commit bed4ff1ed4 upstream.
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c463a158cb upstream.
acpi_gsb_i2c_write_bytes() returns i2c_transfer()'s return value, which
is the number of transfers executed on success, so 1.
The ACPI code expects us to store 0 in gsb->status for success, not 1.
Specifically this breaks the following code in the Thinkpad 8 DSDT:
ECWR = I2CW = ECWR /* \_SB_.I2C1.BAT0.ECWR */
If ((ECST == Zero))
{
ECRD = I2CR /* \_SB_.I2C1.I2CR */
}
Before this commit we set ECST to 1, causing the read to never happen
breaking battery monitoring on the Thinkpad 8.
This commit makes acpi_gsb_i2c_write_bytes() return 0 when i2c_transfer()
returns 1, so the single write transfer completed successfully, and
makes it return -EIO on for other (unexpected) return values >= 0.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1204e35bed upstream.
Commit b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug
events for a device") iterates over the devices on a hotplug port's
subordinate bus in pciehp's IRQ handler without acquiring pci_bus_sem.
It is thus possible for a user to cause a crash by concurrently
manipulating the device list, e.g. by disabling slot power via sysfs
on a different CPU or by initiating a remove/rescan via sysfs.
This can't be fixed by acquiring pci_bus_sem because it may sleep.
The simplest fix is to avoid the list iteration altogether and just
check the ignore_hotplug flag on the port itself. This works because
pci_ignore_hotplug() sets the flag both on the device as well as on its
parent bridge.
We do lose the ability to print the name of the device blocking hotplug
in the debug message, but that's probably bearable.
Fixes: b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 281e878eab upstream.
When pciehp is unbound (e.g. on unplug of a Thunderbolt device), the
hotplug_slot struct is deregistered and thus freed before freeing the
IRQ. The IRQ handler and the work items it schedules print the slot
name referenced from the freed structure in various informational and
debug log messages, each time resulting in a quadruple dereference of
freed pointers (hotplug_slot -> pci_slot -> kobject -> name).
At best the slot name is logged as "(null)", at worst kernel memory is
exposed in logs or the driver crashes:
pciehp 0000:10:00.0:pcie204: Slot((null)): Card not present
An attacker may provoke the bug by unplugging multiple devices on a
Thunderbolt daisy chain at once. Unplugging can also be simulated by
powering down slots via sysfs. The bug is particularly easy to trigger
in poll mode.
It has been present since the driver's introduction in 2004:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Fix by rearranging teardown such that the IRQ is freed first. Run the
work items queued by the IRQ handler to completion before freeing the
hotplug_slot struct by draining the work queue from the ->release_slot
callback which is invoked by pci_hp_deregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.4
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dbe97efe8 upstream.
PCIe r4.0, sec 9.3.5.4, "Device Control Register", shows both
Max_Payload_Size (MPS) and Max_Read_request_Size (MRRS) to be 'RsvdP' for
VFs. Just prior to the table it states:
"PF and VF functionality is defined in Section 7.5.3.4 except where
noted in Table 9-16. For VF fields marked 'RsvdP', the PF setting
applies to the VF."
All of which implies that with respect to Max_Payload_Size Supported
(MPSS), MPS, and MRRS values, we should not be paying any attention to the
VF's fields, but rather only to the PF's. Only looking at the PF's fields
also logically makes sense as it's the sole physical interface to the PCIe
bus.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527
Fixes: 27d868b5e6 ("PCI: Set MPS to match upstream bridge")
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.3+
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Dongdong Liu <liudongdong3@huawei.com>
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ce6435820 upstream.
If addition of sysfs files fails on registration of a hotplug slot, the
struct pci_slot as well as the entry in the slot_list is leaked. The
issue has been present since the hotplug core was introduced in 2002:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Perhaps the idea was that even though sysfs addition fails, the slot
should still be usable. But that's not how drivers use the interface,
they abort probe if a non-zero value is returned.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.4.15+
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b885ac1dc upstream.
Now that mb() is an instruction barrier, it will slow performance if we issue
unnecessary barriers.
The spinlock defines have a number of unnecessary barriers. The __ldcw()
define is both a hardware and compiler barrier. The mb() barriers in the
routines using __ldcw() serve no purpose.
The only barrier needed is the one in arch_spin_unlock(). We need to ensure
all accesses are complete prior to releasing the lock.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caa21e19e0 upstream.
Invoking shutdown for a socket in state SMC_LISTEN does not make
sense. Nevertheless programs like syzbot fuzzing the kernel may
try to do this. For SMC this means a socket refcounting problem.
This patch makes sure a shutdown call for an SMC socket in state
SMC_LISTEN simply returns with -ENOTCONN.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4576cd469d upstream.
TPACKET_V3 stores variable length frames in fixed length blocks.
Blocks must be able to store a block header, optional private space
and at least one minimum sized frame.
Frames, even for a zero snaplen packet, store metadata headers and
optional reserved space.
In the block size bounds check, ensure that the frame of the
chosen configuration fits. This includes sockaddr_ll and optional
tp_reserve.
Syzbot was able to construct a ring with insuffient room for the
sockaddr_ll in the header of a zero-length frame, triggering an
out-of-bounds write in dev_parse_header.
Convert the comparison to less than, as zero is a valid snap len.
This matches the test for minimum tp_frame_size immediately below.
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Fixes: eb73190f4f ("net/packet: refine check for priv area size")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6613b6173d upstream.
When first DCCP packet is SYNC or SYNCACK, we insert a new conntrack
that has an un-initialized timeout value, i.e. such entry could be
reaped at any time.
Mark them as INVALID and only ignore SYNC/SYNCACK when connection had
an old state.
Reported-by: syzbot+6f18401420df260e37ed@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7797167ffd upstream.
Now that we use a sync prior to releasing the locks in syscall.S, we don't need
the PA 2.0 ordered stores used to release some locks. Using an ordered store,
potentially slows the release and subsequent code.
There are a number of other ordered stores and loads that serve no purpose. I
have converted these to normal stores.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9432a31757 upstream.
A comment warning against this bug is there, but the code is not doing what
the comment says. Therefore it is possible that an EPOLLHUP races against
irq_bypass_register_consumer. The EPOLLHUP handler schedules irqfd_shutdown,
and if that runs soon enough, you get a use-after-free.
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b38276813 ]
The old code in nvme_user_cmd() passed the userspace virtual address
from nvme_passthru_cmd.metadata as the length of the metadata buffer
as well as the address to nvme_submit_user_cmd().
Fixes: 63263d60 ("nvme: Use metadata for passthrough commands")
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e01a06c808 ]
The Marvell switches report their interrupts in a level sensitive way.
When using edge sensitive detection a race condition in the interrupt
handler of the swich might result in the OS to miss all future events
which might make the switch non-functional.
The problem is that both mv88e6xxx_g2_irq_thread_fn() and
mv88e6xxx_g1_irq_thread_work() sample the irq cause register
(MV88E6XXX_G2_INT_SRC and MV88E6XXX_G1_STS respectively) once and then
handle the observed sources. If after sampling but before all observed
irq sources are handled a new irq source gets active this is not noticed
by the handler which returns unsuspecting, but the interrupt line stays
active which prevents the edge detector to kick in.
All device trees but imx6qdl-zii-rdu2 get this right (most of them by
not specifying an interrupt parent). So fix imx6qdl-zii-rdu2
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f64992d1a9 ("ARM: dts: imx6: RDU2: Add Switch interrupts")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c4d6baf1b ]
The ec_no_wakeup matcher added for Thinkpad X1 Carbon 6th gen systems
beyond matched only a single DMI model (20KGS3JF01), that didn't cover
my laptop (20KH002JUS). Change to match based on DMI product family to
cover all X1 6th gen systems.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e56b8ce363 ]
Attempt to make cryptic TCP seq number error messages clearer by
(1) identifying the source of the message as "TCP", (2) identifying the
errors as "seq # bug", and (3) grouping the field identifiers and values
by separating them with commas.
E.g., the following message is changed from:
recvmsg bug 2: copied 73BCB6CD seq 70F17CBE rcvnxt 73BCB9AA fl 0
WARNING: CPU: 2 PID: 1501 at /linux/net/ipv4/tcp.c:1881 tcp_recvmsg+0x649/0xb90
to:
TCP recvmsg seq # bug 2: copied 73BCB6CD, seq 70F17CBE, rcvnxt 73BCB9AA, fl 0
WARNING: CPU: 2 PID: 1501 at /linux/net/ipv4/tcp.c:2011 tcp_recvmsg+0x694/0xba0
Suggested-by: 積丹尼 Dan Jacobson <jidanni@jidanni.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 711c62dfa6 ]
In case the SPI thread is not running, a simple reset of sync
state won't fix the transmit timeout. We also need to wake up the kernel
thread.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: ed7d42e24e ("net: qca_spi: fix transmit queue timeout handling")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b2bab426dc ]
As long as the synchronization with the QCA7000 isn't finished, we
cannot accept packets from the upper layers. So let the SPI thread
enable the TX queue after sync and avoid unwanted packet drop.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e10f780503 ]
Inside a nested guest, access to hardware can be slow enough that
tsc_read_refs always return ULLONG_MAX, causing tsc_refine_calibration_work
to be called periodically and the nested guest to spend a lot of time
reading the ACPI timer.
However, if the TSC frequency is available from the pvclock page,
we can just set X86_FEATURE_TSC_KNOWN_FREQ and avoid the recalibration.
'refine' operation.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
[Commit message rewritten. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a9b045506 ]
This driver can spam the kernel log with multiple messages of:
net eth0: eth0: allmulti set
Usually 4 or 8 at a time (probably because of using ConnMan).
This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4aac0b4347 ]
octeon_mgmt driver doesn't drop RX frames that are 1-4 bytes bigger than
MTU set for the corresponding interface. The problem is in the
AGL_GMX_RX0/1_FRM_MAX register setting, which should not account for VLAN
tagging.
According to Octeon HW manual:
"For tagged frames, MAX increases by four bytes for each VLAN found up to a
maximum of two VLANs, or MAX + 8 bytes."
OCTEON_FRAME_HEADER_LEN "define" is fine for ring buffer management, but
should not be used for AGL_GMX_RX0/1_FRM_MAX.
The problem could be easily reproduced using "ping" command. If affected
system has default MTU 1500, other host (having MTU >= 1504) can
successfully "ping" the affected system with payload size 1473-1476,
resulting in IP packets of size 1501-1504 accepted by the mgmt driver.
Fixed system still accepts IP packets of 1500 bytes even with VLAN tagging,
because the limits are lifted in HW as expected, for every VLAN tag.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 665d4953cd ]
In commit ac0b4145d6 ("btrfs: scrub: Don't use inode pages for device
replace") we removed the branch of copy_nocow_pages() to avoid
corruption for compressed nodatasum extents.
However above commit only solves the problem in scrub_extent(), if
during scrub_pages() we failed to read some pages,
sctx->no_io_error_seen will be non-zero and we go to fixup function
scrub_handle_errored_block().
In scrub_handle_errored_block(), for sctx without csum (no matter if
we're doing replace or scrub) we go to scrub_fixup_nodatasum() routine,
which does the similar thing with copy_nocow_pages(), but does it
without the extra check in copy_nocow_pages() routine.
So for test cases like btrfs/100, where we emulate read errors during
replace/scrub, we could corrupt compressed extent data again.
This patch will fix it just by avoiding any "optimization" for
nodatasum, just falls back to the normal fixup routine by try read from
any good copy.
This also solves WARN_ON() or dead lock caused by lame backref iteration
in scrub_fixup_nodatasum() routine.
The deadlock or WARN_ON() won't be triggered before commit ac0b4145d6
("btrfs: scrub: Don't use inode pages for device replace") since
copy_nocow_pages() have better locking and extra check for data extent,
and it's already doing the fixup work by try to read data from any good
copy, so it won't go scrub_fixup_nodatasum() anyway.
This patch disables the faulty code and will be removed completely in a
followup patch.
Fixes: ac0b4145d6 ("btrfs: scrub: Don't use inode pages for device replace")
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3578a7ecb6 ]
Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered. Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c133459765 ]
CC [M] drivers/net/ethernet/freescale/fman/fman.o
In file included from ../drivers/net/ethernet/freescale/fman/fman.c:35:
../include/linux/fsl/guts.h: In function 'guts_set_dmacr':
../include/linux/fsl/guts.h:165:2: error: implicit declaration of function 'clrsetbits_be32' [-Werror=implicit-function-declaration]
clrsetbits_be32(&guts->dmacr, 3 << shift, device << shift);
^~~~~~~~~~~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 916c5e1413 ]
The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.
Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3ffe64f1a6 ("hv_netvsc: split sub-channel setup into async and sync")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c29e9da56b ]
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Fixes: cc4fa83f66 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 993675a310 ]
If variable length link layer headers result in a packet shorter
than dev->hard_header_len, reset the network header offset. Else
skb->mac_len may exceed skb->len after skb_mac_reset_len.
packet_sendmsg_spkt already has similar logic.
Fixes: b84bbaf7a6 ("packet: in packet_snd start writing at link layer allocation")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d14c780c11 ]
This change makes it so that we are much more explicit about the ordering
of updates to the receive address register (RAR) table. Prior to this patch
I believe we may have been updating the table while entries were still
active, or possibly allowing for reordering of things since we weren't
explicitly flushing writes to either the lower or upper portion of the
register prior to accessing the other half.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 923847413f ]
The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi. This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f8b5b2183 ]
Call secure services to enable ACTLR[0] (Enable invalidates of BTB with
ICIALLU) when branch hardening is enabled for kernel.
On GP devices OMAP5/DRA7, there is no possibility to update secure
side since "secure world" is ROM and there are no override mechanisms
possible. On HS devices, appropriate PPA should do the workarounds as
well.
However, the configuration is only done for secondary core, since it is
expected that firmware/bootloader will have enabled the required
configuration for the primary boot core (note: bootloaders typically
will NOT enable secondary processors, since it has no need to do so).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4c7e2bd2e ]
Dynamic ftrace requires modifying the code segments that are usually
set to read-only. To do this, a per arch function is called both before
and after the ftrace modifications are performed. The "before" function
will set kernel code text to read-write to allow for ftrace to make the
modifications, and the "after" function will set the kernel code text
back to "read-only" to keep the kernel code text protected.
The issue happens when dynamic ftrace is tested at boot up. The test is
done before the kernel code text has been set to read-only. But the
"before" and "after" calls are still performed. The "after" call will
change the kernel code text to read-only prematurely, and other boot
code that expects this code to be read-write will fail.
The solution is to add a variable that is set when the kernel code text
is expected to be converted to read-only, and make the ftrace "before"
and "after" calls do nothing if that variable is not yet set. This is
similar to the x86 solution from commit 1623963097 ("ftrace, x86:
make kernel text writable only for conversions").
Link: http://lkml.kernel.org/r/20180620212906.24b7b66e@vmware.local.home
Reported-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee6581ceba ]
Incremental patch to fix the unchecked dereference in acpi_nfit_ctl.
Reported by Dan Carpenter:
"acpi/nfit: fix cmd_rc for acpi_nfit_ctl to
always return a value" from Jun 28, 2018, leads to the following
Smatch complaint:
drivers/acpi/nfit/core.c:578 acpi_nfit_ctl()
warn: variable dereferenced before check 'cmd_rc' (see line 411)
drivers/acpi/nfit/core.c
410
411 *cmd_rc = -EINVAL;
^^^^^^^^^^^^^^^^^^
Patch adds unchecked dereference.
Fixes: c1985cefd8 ("acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db0ba84c04 ]
The dictionaries are attached to the parameter tuple that steals the
references and takes care of releasing them when appropriate. The code
should not decrement the reference counts explicitly. E.g. if libpython
has been built with reference debugging enabled, the superfluous DECREFs
will trigger this error when running perf script:
Fatal Python error: Objects/tupleobject.c:238 object at
0x7f10f2041b40 has negative ref count -1
Aborted (core dumped)
If the reference debugging is not enabled, the superfluous DECREFs might
cause the dict objects to be silently released while they are still in
use. This may trigger various other assertions or just cause perf
crashes and/or weird and unexpected data changes in the stored Python
objects.
Signed-off-by: Janne Huttunen <janne.huttunen@nokia.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jaroslav Skarvada <jskarvad@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1531133990-17485-1-git-send-email-janne.huttunen@nokia.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a09603f851 ]
We are getting following warnings on gcc8 that break compilation:
$ make
CC jvmti/jvmti_agent.o
jvmti/jvmti_agent.c: In function ‘jvmti_open’:
jvmti/jvmti_agent.c:252:35: error: ‘/jit-’ directive output may be truncated \
writing 5 bytes into a region of size between 1 and 4096 [-Werror=format-truncation=]
snprintf(dump_path, PATH_MAX, "%s/jit-%i.dump", jit_path, getpid());
There's no point in checking the result of snprintf call in
jvmti_open, the following open call will fail in case the
name is mangled or too long.
Using tools/lib/ function scnprintf that touches the return value from
the snprintf() calls and thus get rid of those warnings.
$ make DEBUG=1
CC arch/x86/util/perf_regs.o
arch/x86/util/perf_regs.c: In function ‘arch_sdt_arg_parse_op’:
arch/x86/util/perf_regs.c:229:4: error: ‘strncpy’ output truncated before terminating nul
copying 2 bytes from a string of the same length [-Werror=stringop-truncation]
strncpy(prefix, "+0", 2);
^~~~~~~~~~~~~~~~~~~~~~~~
Using scnprintf instead of the strncpy (which we know is safe in here)
to get rid of that warning.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180702134202.17745-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
