PD#SWPL-4761
Problem:
When slave device is busy processing, it is unable to handle the
incoming communication attempts. i2c master have to repeatedly attemp
communication until the slave sends an ACK after receiving its slave
address.
Solution:
add retry-process when slave NACK.
Verify:
mesonaxg_s420_32_release
Change-Id: Ieb195176cac4b80e223ea6adb502ffd3bc9ef728
Signed-off-by: Daogao Xu <daogao.xu@amlogic.com>
PD#SWPL-5555
Problem:
Current driver does not support both NEC and RC5
Solution:
Add a macro to depecit both NEC and RC5 state
Verify:
X301
Change-Id: I06894d033eabdb22db6e34fc2ad76e0390ef565f
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
PD#SWPL-5574
Problem:
amixer return error due to ad82584f not exist in W411 platform
Solution:
Disable ad82584f, and remove it from TDM output list
Verify:
Yes
Change-Id: I7fcd5ad31ba57887399c45d67b130e8c3d08e671
Signed-off-by: Blance Tang <guofeng.tang@amlogic.com>
PD#SWPL-4854
Problem:
TXL DTMB has losing lock issue
Solution:
set HHI_DEMOD_CLK_CNTL to 0x301 for TXL
Verify:
verified by t962_p321
Change-Id: I51b61949b5f9c96b64eae7e0054771ce44dbfd5b
Signed-off-by: zhiwei.yuan <zhiwei.yuan@amlogic.com>
PD#SWPL-5202
Problem:
cma memory is not released when suspend
Solution:
provide suspend interface to release cma memory
Verify:
verified by t962x2_x301
Change-Id: I1d808a8a6119a2f385961c4c5bded5ab71c9c9d1
Signed-off-by: zhiwei.yuan <zhiwei.yuan@amlogic.com>
PD#SWPL-4975
Problem:
some basic saradc registers are only initialized at bl2 stage, the ADC
value is abnormal when bl2 disable saradc init.
Solution:
to re-initialize the basic saradc registers in kernel.
Verify:
test pass on w400 and p212
Change-Id: Ie98e8789fd47cc43cafcb49d9862ccccbe1d9b66
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
PD#OTT-2168
Problem:
media control bar can't displayed because afbc source crop not support
Solution:
add afbc source crop support
Verify:
verify on raven
Change-Id: Ib1f925aeea12ba18d8f976aba8c84f0738c41293
Signed-off-by: Pengcheng Chen <pengcheng.chen@amlogic.com>
PD#SWPL-5014
Problem:
ppmgr provider error sometimes in long time run under poor signal
Solution:
use light reg for video decoder local reset
Verify:
X301
Change-Id: I1500c9ddfdce76b3e9cb2b24a35cdee765f82d5f
Signed-off-by: Hui Zhang <hui.zhang@amlogic.com>
PD#SWPL-5295
Problem:
add RX delay for 8211f and add led setup interface
Solution:
tuning delay and leds
Verify:
verify on u200 board
Change-Id: I45e855894d570fdd976f90fd8f03151ad52a3683
Signed-off-by: Zhuo Wang <zhuo.wang@amlogic.com>
PD#SWPL-5206
Problem:
Setup time in sdio highspeed mode of txlx is
inconsistent with the protocol standard.
Solution:
set co_phase = 2.
Verify:
r321
Change-Id: I3e5a1bca335faea6397513de772d3ee35ea76d40
Signed-off-by: Nan Li <nan.li@amlogic.com>
PD#SWPL-3300
Problem:
local contrast interface for pc tool
Solution:
add driver interface for pc tool
Verify:
tl1
Change-Id: I874ebc6c234f1030fa64a48033580af644550048
Signed-off-by: Bencheng Jing <bencheng.jing@amlogic.com>
PD#TV-2272
Problem:
can't get corrent reboot reason in system panic
Solution:
get corrent reboot reason in system panic
Verify:
test pass on T962x2_x301
Change-Id: If0fc95c2807d89542b4ccbc8e3709be20f17b03b
Signed-off-by: Hong Guo <hong.guo@amlogic.com>
PD#SWPL-5017
Problem:
need support dummy lcd for viu1
Solution:
add dummp_panel display mode.
when need viu1 + viu2 -> encl, and show viu2 data,
you can use below setting:
echo dump_panel >/sys/class/display/mode
echo panel >/sys/class/display2/mode
Verify:
x301
Change-Id: I8a7fb52e2272fc8f71d682424ff20dc37f02b726
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
PD#SWPL-3365
Problem:
system would reboot when carshed by hw resample
Solution:
actrl of toddr is modified to null pointer, so it leads to crash.
fix to pass toddr pointer to function, not fetched by resample module.
Verify:
TL1 socket board
Change-Id: I9227ef2e1ca225e72b0408bc694e6a20d623c8a9
Signed-off-by: huijie.huang <huijie.huang@amlogic.com>
PD#SWPL-4421
Problem:
Tuner crashes easily when fast fine tune
Solution:
Delay afc work to prevent tuner crash
Verify:
verified by x301
Change-Id: I011f7c3f71a30f95a9b7aa371d5fabe71f249051
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
PD#SWPL-4733
Problem:
The Speaker has noise
Solution:
The binv is not correct for TDM out c,
we will use amixer to set it
Verify:
A113
Change-Id: I7c8af8e00e3c8834533347947630a6944b7e2136
Signed-off-by: yujie.wu <yujie.wu@amlogic.com>
PD#SWPL-4737
Problem:
HDMI in and Line in use the same device.
But their input I2S inskew is not same.
Solution:
We need use separate skew setting for different
source.
Verify:
A113
Change-Id: I8e306af06d9c9d614c4032f2030dbedb64a7f6df
Signed-off-by: yujie.wu <yujie.wu@amlogic.com>
PD#SWPL-4680
Problem:
unify lcd driver frame_rate change function
Solution:
create a unified api(lcd_clk_change) to management the function
Verify:
verify by t962x2-r311
Change-Id: I1ab378aa2556db0636aabe8c20f3b97845b8184f
Signed-off-by: Shaochan Liu <shaochan.liu@amlogic.com>
PD#SWPL-4225
Problem:
This interface is added to facilitate debugging the voltage-
table in pwm regulator, which can output different percentages
of waveforms in a fixed pwm cycle.
example:
echo 50 100 > sys/class/pwm/pwmchipx/pwmx/relative_duty
output 50% duty pwm
Solution:
add relative_duty interface in pwm sysfs
Verify:
test pass on tl1_X301_v1 tl1_skt_v1
Change-Id: Icd01e681694b81f3790f7cce8c326db02674a48c
Signed-off-by: Bichao Zheng <bichao.zheng@amlogic.com>
PD#SWPL-3081
Problem:
1,lack suspend/resume function
2,lack reset pin control
Solution:
1,add suspend/resume function
2, add reset pin control
Verify:
962x2
Signed-off-by: Che Song <che.song@amlogic.com>
Change-Id: I1cb920fdba4ad32048518fdad93e3a5a81039dd9
PD#SWPL-3902
Problem:
If cma page is unevictable, migrate it will cost long time.
Solution:
1. Recalim unevictable cma file cache pages.
2. Using CMA after first water mark not ok.
Verify:
einstern
Change-Id: I0ecbf5dd535cb034430c4ea623891e7a7ae6e4dd
Signed-off-by: Tao Zeng <tao.zeng@amlogic.com>
PD#SWPL-4350
Problem:
ramdump is not enabled on g12b/gxl.
Solution:
Add ramdump support on g12b/gxl in bl2.
Verify:
verified on g12b_w400_v1/gxl_p212_v1.
Change-Id: I3520fea366af332ef113809560587eeb4db7b6c5
Signed-off-by: changqing.gao <changqing.gao@amlogic.com>
PD#SH-327
Problem:
uart default min baud rate was set 9600, but PTZ PELCO-D
and PELCO-P need uart driver support 2400 and 4800 baud rate
Solution:
change baud rate minimum value to 2400
Verify:
Local
Change-Id: Iee20ea30a95b89f89a59fab95cecf7d559cbff51
Signed-off-by: Dianzhong Huo <dianzhong.huo@amlogic.com>
PD#SWPL-4839
Problem:
have risk of unmap ge2d dma_buf
Solution:
unmap ge2d dma_buf after ge2d process finished
Verify:
verify by w400
Change-Id: Ia84786b297f8e95cc9efc038300917c98d6b73f6
Signed-off-by: Pengcheng Chen <pengcheng.chen@amlogic.com>
Signed-off-by: Jian Cao <jian.cao@amlogic.com>
PD#SWPL-4387
Problem:
system would reboot when carshed by hw resample
Solution:
actrl of toddr is modified to null pointer, so it leads to crash.
fix to pass toddr pointer to function, not fetched by resample module.
Verify:
x301
Change-Id: I91c30260ee825d843e8ed17304031382b42ac119
Signed-off-by: Xing Wang <xing.wang@amlogic.com>
PD#SWPL-4233
Problem:
3D framepacking mode display black screen
Solution:
Add vinfo 3d flag and hdmitx update
when work 3d mode
Verify:
U212
Change-Id: Ia2b7b25c9ed401dbec2c487ea2a5c6cc1e0d8b8d
Signed-off-by: Kaifu Hu <kaifu.hu@amlogic.com>
PD#SWPL-4501
Problem:
All platforms but m8b use "gpio_periphs" as gpio pinctrl function, that
breaks consistency.
Solution:
rename m8b pinctrl function "gpio" to "gpio_periphs" to make it
consistent with code and other platform.
ref:
https://patchwork.kernel.org/patch/10720219/
Verify:
m200
Change-Id: I940d1e30882cc8b042c02022ed3435a659aa3921
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
PD#SWPL-4355
Problem:
ge2d: Adjust scaler para when input is nv21 and output is rgb
Solution:
merge patch 'Adjust scaler para when input is nv21 and output is rgb'
from amlogic-3.14-dev(PD#15652)
Verify:
verified on u200
Change-Id: I199b07d683a01175ec17d4d34be6febd3083920c
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
Signed-off-by: Jian Cao <jian.cao@amlogic.com>
PD#SWPL-4355
Problem:
ge2d: play video display mess when used ionvideo
Solution:
merge patch 'play video display mess when used ionvideo'
from amlogic-3.14-dev(PD#155143)
Verify:
verified on u200
Change-Id: Iaf34fe1d1c7e7637015dadaaf43e201cf28089b7
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
Signed-off-by: Jian Cao <jian.cao@amlogic.com>
PD#SWPL-4351
Problem:
Our cpu has 4 watch point on each cpu. It can be used for debug
purpose. But currently there is no driver support it.
Solution:
Bring up driver for it.
Verify:
p212
Change-Id: Ifbcb7f9b77e10fcb03b3c1a5e18f06b1a56ec2f0
Signed-off-by: Tao Zeng <tao.zeng@amlogic.com>
PD#TV-470
Problem:
t950 ddr bandwidth usage is error
Solution:
t950/805x ddr is 16bit, correct the param to get right usage
Verify:
t950
Change-Id: Ice876f82e5c33e778b3ac9f593e0c163d57d7f3f
Signed-off-by: wenbiao zhang <wenbiao.zhang@amlogic.com>
PD#TV-2088
Problem:
wifi can not power in driver
Solution:
export set_usb_wifi_power
Verify:
franklin
Change-Id: Ic6fb75133533c395cd96e9d82f14427cf40cee96
Signed-off-by: Rongjun Chen <rongjun.chen@amlogic.com>
