commit 686f85d71d upstream.
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 772f66421d upstream.
Section 4.3.1 of the datasheet says,
This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.
Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.
After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.
When in reset mode, take the opportunity to reset the CAM Enable
register.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27e0c31c5f upstream.
There are several issues relating to command register usage during
chip initialization.
Firstly, the SONIC sometimes comes out of software reset with the
Start Timer bit set. This gets logged as,
macsonic macsonic eth0: sonic_init: status=24, i=101
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89ba879e95 upstream.
As soon as the driver is finished with a receive buffer it allocs a new
one and overwrites the corresponding RRA entry with a new buffer pointer.
Problem is, the buffer pointer is split across two word-sized registers.
It can't be updated in one atomic store. So this operation races with the
chip while it stores received packets and advances its RRP register.
This could result in memory corruption by a DMA write.
Avoid this problem by adding buffers only at the location given by the
RWP register, in accordance with the National Semiconductor datasheet.
Re-factor this code into separate functions to calculate a RRA pointer
and to update the RWP.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94b1663495 upstream.
After sonic_tx_timeout() calls sonic_init(), it can happen that
sonic_rx() will subsequently encounter a receive descriptor with no
flags set. Remove the comment that says that this can't happen.
When giving a receive descriptor to the SONIC, clear the descriptor
status field. That way, any rx descriptor with flags set can only be
a newly received packet.
Don't process a descriptor without the LPKT bit set. The buffer is
still in use by the SONIC.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaabfd19b2 upstream.
The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e311820f6 upstream.
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427db97df1 upstream.
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3885f5761 upstream.
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fedabf5a7 upstream.
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 865ad2f220 upstream.
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0cb50185a upstream.
may_create_in_sticky() call is done when we already have dropped the
reference to dir.
Fixes: 30aba6656f (namei: allow restricted O_CREAT of FIFOs and regular files)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0695e2351 upstream.
Just as commit 0566e40ce7 ("tracing: initcall: Ordered comparison of
function pointers"), this patch fixes another remaining one in xen.h
found by clang-9.
In file included from arch/x86/xen/trace.c:21:
In file included from ./include/trace/events/xen.h:475:
In file included from ./include/trace/define_trace.h:102:
In file included from ./include/trace/trace_events.h:473:
./include/trace/events/xen.h:69:7: warning: ordered comparison of function \
pointers ('xen_mc_callback_fn_t' (aka 'void (*)(void *)') and 'xen_mc_callback_fn_t') [-Wordered-compare-function-pointers]
__field(xen_mc_callback_fn_t, fn)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/trace/trace_events.h:421:29: note: expanded from macro '__field'
^
./include/trace/trace_events.h:407:6: note: expanded from macro '__field_ext'
is_signed_type(type), filter_type); \
^
./include/linux/trace_events.h:554:44: note: expanded from macro 'is_signed_type'
^
Fixes: c796f213a6 ("xen/trace: add multicall tracing")
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97e24b0953 upstream.
The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.
Fixes: e28d0c9cd3 ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3111491fca upstream.
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-3-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8eeb74df5 upstream.
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 162f98dea4 ("Input: gtco - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-5-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b32391ed6 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 996d5d5f89 upstream.
Setting the vibrator enable_mask is not implemented correctly:
For regmap_update_bits(map, reg, mask, val) we give in either
regs->enable_mask or 0 (= no-op) as mask and "val" as value.
But "val" actually refers to the vibrator voltage control register,
which has nothing to do with the enable_mask.
So we usually end up doing nothing when we really wanted
to enable the vibrator.
We want to set or clear the enable_mask (to enable/disable the vibrator).
Therefore, change the call to always modify the enable_mask
and set the bits only if we want to enable the vibrator.
Fixes: d4c7c5c96c ("Input: pm8xxx-vib - handle separate enable register")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200114183442.45720-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de19055564 upstream.
For a while Arm64 has been capable of force enabling
or disabling the kpti mitigations. Lets make sure the
documentation reflects that.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 927d780ee3 upstream.
Scenario 1, ARMv7
=================
If code in arch/arm/kernel/ftrace.c would operate on mcount() pointer
the following may be generated:
00000230 <prealloc_fixed_plts>:
230: b5f8 push {r3, r4, r5, r6, r7, lr}
232: b500 push {lr}
234: f7ff fffe bl 0 <__gnu_mcount_nc>
234: R_ARM_THM_CALL __gnu_mcount_nc
238: f240 0600 movw r6, #0
238: R_ARM_THM_MOVW_ABS_NC __gnu_mcount_nc
23c: f8d0 1180 ldr.w r1, [r0, #384] ; 0x180
FTRACE currently is not able to deal with it:
WARNING: CPU: 0 PID: 0 at .../kernel/trace/ftrace.c:1979 ftrace_bug+0x1ad/0x230()
...
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.116-... #1
...
[<c0314e3d>] (unwind_backtrace) from [<c03115e9>] (show_stack+0x11/0x14)
[<c03115e9>] (show_stack) from [<c051a7f1>] (dump_stack+0x81/0xa8)
[<c051a7f1>] (dump_stack) from [<c0321c5d>] (warn_slowpath_common+0x69/0x90)
[<c0321c5d>] (warn_slowpath_common) from [<c0321cf3>] (warn_slowpath_null+0x17/0x1c)
[<c0321cf3>] (warn_slowpath_null) from [<c038ee9d>] (ftrace_bug+0x1ad/0x230)
[<c038ee9d>] (ftrace_bug) from [<c038f1f9>] (ftrace_process_locs+0x27d/0x444)
[<c038f1f9>] (ftrace_process_locs) from [<c08915bd>] (ftrace_init+0x91/0xe8)
[<c08915bd>] (ftrace_init) from [<c0885a67>] (start_kernel+0x34b/0x358)
[<c0885a67>] (start_kernel) from [<00308095>] (0x308095)
---[ end trace cb88537fdc8fa200 ]---
ftrace failed to modify [<c031266c>] prealloc_fixed_plts+0x8/0x60
actual: 44:f2:e1:36
ftrace record flags: 0
(0) expected tramp: c03143e9
Scenario 2, ARMv4T
==================
ftrace: allocating 14435 entries in 43 pages
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/trace/ftrace.c:2029 ftrace_bug+0x204/0x310
CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.5 #1
Hardware name: Cirrus Logic EDB9302 Evaluation Board
[<c0010a24>] (unwind_backtrace) from [<c000ecb0>] (show_stack+0x20/0x2c)
[<c000ecb0>] (show_stack) from [<c03c72e8>] (dump_stack+0x20/0x30)
[<c03c72e8>] (dump_stack) from [<c0021c18>] (__warn+0xdc/0x104)
[<c0021c18>] (__warn) from [<c0021d7c>] (warn_slowpath_null+0x4c/0x5c)
[<c0021d7c>] (warn_slowpath_null) from [<c0095360>] (ftrace_bug+0x204/0x310)
[<c0095360>] (ftrace_bug) from [<c04dabac>] (ftrace_init+0x3b4/0x4d4)
[<c04dabac>] (ftrace_init) from [<c04cef4c>] (start_kernel+0x20c/0x410)
[<c04cef4c>] (start_kernel) from [<00000000>] ( (null))
---[ end trace 0506a2f5dae6b341 ]---
ftrace failed to modify
[<c000c350>] perf_trace_sys_exit+0x5c/0xe8
actual: 1e:ff:2f:e1
Initializing ftrace call sites
ftrace record flags: 0
(0)
expected tramp: c000fb24
The analysis for this problem has been already performed previously,
refer to the link below.
Fix the above problems by allowing only selected reloc types in
__mcount_loc. The list itself comes from the legacy recordmcount.pl
script.
Link: https://lore.kernel.org/lkml/56961010.6000806@pengutronix.de/
Cc: stable@vger.kernel.org
Fixes: ed60453fa8 ("ARM: 6511/1: ftrace: add ARM support for C version of recordmcount")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba9a103f40 upstream.
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 99f83c9c9a ("[PATCH] USB: add driver for Keyspan Digital Remote")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 2.6.13
Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeed8aa387 upstream.
With CONFIG_PROVE_RCU_LIST, I had many suspicious RCU warnings
when I ran ftracetest trigger testcases.
-----
# dmesg -c > /dev/null
# ./ftracetest test.d/trigger
...
# dmesg | grep "RCU-list traversed" | cut -f 2 -d ] | cut -f 2 -d " "
kernel/trace/trace_events_hist.c:6070
kernel/trace/trace_events_hist.c:1760
kernel/trace/trace_events_hist.c:5911
kernel/trace/trace_events_trigger.c:504
kernel/trace/trace_events_hist.c:1810
kernel/trace/trace_events_hist.c:3158
kernel/trace/trace_events_hist.c:3105
kernel/trace/trace_events_hist.c:5518
kernel/trace/trace_events_hist.c:5998
kernel/trace/trace_events_hist.c:6019
kernel/trace/trace_events_hist.c:6044
kernel/trace/trace_events_trigger.c:1500
kernel/trace/trace_events_trigger.c:1540
kernel/trace/trace_events_trigger.c:539
kernel/trace/trace_events_trigger.c:584
-----
I investigated those warnings and found that the RCU-list
traversals in event trigger and hist didn't need to use
RCU version because those were called only under event_mutex.
I also checked other RCU-list traversals related to event
trigger list, and found that most of them were called from
event_hist_trigger_func() or hist_unregister_trigger() or
register/unregister functions except for a few cases.
Replace these unneeded RCU-list traversals with normal list
traversal macro and lockdep_assert_held() to check the
event_mutex is held.
Link: http://lkml.kernel.org/r/157680910305.11685.15110237954275915782.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: 30350d65ac ("tracing: Add variable support to hist triggers")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e89cd303e upstream.
To account for parts of the chip that are "harvested" (disabled) due to
silicon flaws, caches on some AMD GPUs must be initialized before ATS is
enabled.
ATS is normally enabled by the IOMMU driver before the GPU driver loads, so
this cache initialization would have to be done in a quirk, but that's too
complex to be practical.
For Navi14 (device ID 0x7340), this initialization is done by the VBIOS,
but apparently some boards went to production with an older VBIOS that
doesn't do it. Disable ATS for those boards.
Link: https://lore.kernel.org/r/20200114205523.1054271-3-alexander.deucher@amd.com
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1015
See-also: d28ca864c4 ("PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken")
See-also: 9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
[bhelgaas: squash into one patch, simplify slightly, commit log]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bf8bdcf3b upstream.
The hwmon core uses device managed functions, tied to the hwmon parent
device, for various internal memory allocations. This is problematic
since hwmon device lifetime does not necessarily match its parent's
device lifetime. If there is a mismatch, memory leaks will accumulate
until the parent device is released.
Fix the problem by managing all memory allocations internally. The only
exception is memory allocation for thermal device registration, which
can be tied to the hwmon device, along with thermal device registration
itself.
Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Cc: stable@vger.kernel.org # v4.14.x: 47c332deb8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.14.x: 74e3512731: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9.x: 3a412d5e4a: hwmon: (core) Simplify sysfs attribute name allocation
Cc: stable@vger.kernel.org # v4.9.x: 47c332deb8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.9.x: 74e3512731: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9+
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf3ca18775 upstream.
reg2volt returns the voltage that matches a given register value.
Converting this back the other way with volt2reg didn't return the same
register value because it used truncation instead of rounding.
This meant that values read from sysfs could not be written back to sysfs
to set back the same register value.
With this change, volt2reg will return the same value for every voltage
previously returned by reg2volt (for the set of possible input values)
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191205231659.1301-1-luuk.paulussen@alliedtelesis.co.nz
cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a45ea48e2b upstream.
The afs filesystem needs to prohibit certain characters from cell names,
such as '/', as these are used to form filenames in procfs, leading to
the following warning being generated:
WARNING: CPU: 0 PID: 3489 at fs/proc/generic.c:178
Fix afs_alloc_cell() to disallow nonprintable characters, '/', '@' and
names that begin with a dot.
Remove the check for "@cell" as that is then redundant.
This can be tested by running:
echo add foo/.bar 1.2.3.4 >/proc/fs/afs/cells
Note that we will also need to deal with:
- Names ending in ".invalid" shouldn't be passed to the DNS.
- Names that contain non-valid domainname chars shouldn't be passed to
the DNS.
- DNS replies that say "your-dns-needs-immediate-attention.<gTLD>" and
replies containing A records that say 127.0.53.53 should be
considered invalid.
[https://www.icann.org/en/system/files/files/name-collision-mitigation-01aug14-en.pdf]
but these need to be dealt with by the kafs-client DNS program rather
than the kernel.
Reported-by: syzbot+b904ba7c947a37b4b291@syzkaller.appspotmail.com
Cc: stable@kernel.org
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1efba987c4 ]
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Petar Penkov <ppenkov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2bec445f9b ]
Latest commit 853697504d ("tcp: Fix highest_sack and highest_sack_seq")
apparently allowed syzbot to trigger various crashes in TCP stack [1]
I believe this commit only made things easier for syzbot to find
its way into triggering use-after-frees. But really the bugs
could lead to bad TCP behavior or even plain crashes even for
non malicious peers.
I have audited all calls to tcp_rtx_queue_unlink() and
tcp_rtx_queue_unlink_and_free() and made sure tp->highest_sack would be updated
if we are removing from rtx queue the skb that tp->highest_sack points to.
These updates were missing in three locations :
1) tcp_clean_rtx_queue() [This one seems quite serious,
I have no idea why this was not caught earlier]
2) tcp_rtx_queue_purge() [Probably not a big deal for normal operations]
3) tcp_send_synack() [Probably not a big deal for normal operations]
[1]
BUG: KASAN: use-after-free in tcp_highest_sack_seq include/net/tcp.h:1864 [inline]
BUG: KASAN: use-after-free in tcp_highest_sack_seq include/net/tcp.h:1856 [inline]
BUG: KASAN: use-after-free in tcp_check_sack_reordering+0x33c/0x3a0 net/ipv4/tcp_input.c:891
Read of size 4 at addr ffff8880a488d068 by task ksoftirqd/1/16
CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.5.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:639
__asan_report_load4_noabort+0x14/0x20 mm/kasan/generic_report.c:134
tcp_highest_sack_seq include/net/tcp.h:1864 [inline]
tcp_highest_sack_seq include/net/tcp.h:1856 [inline]
tcp_check_sack_reordering+0x33c/0x3a0 net/ipv4/tcp_input.c:891
tcp_try_undo_partial net/ipv4/tcp_input.c:2730 [inline]
tcp_fastretrans_alert+0xf74/0x23f0 net/ipv4/tcp_input.c:2847
tcp_ack+0x2577/0x5bf0 net/ipv4/tcp_input.c:3710
tcp_rcv_established+0x6dd/0x1e90 net/ipv4/tcp_input.c:5706
tcp_v4_do_rcv+0x619/0x8d0 net/ipv4/tcp_ipv4.c:1619
tcp_v4_rcv+0x307f/0x3b40 net/ipv4/tcp_ipv4.c:2001
ip_protocol_deliver_rcu+0x5a/0x880 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x23b/0x380 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip_local_deliver+0x1e9/0x520 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x1db/0x2f0 net/ipv4/ip_input.c:428
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip_rcv+0xe8/0x3f0 net/ipv4/ip_input.c:538
__netif_receive_skb_one_core+0x113/0x1a0 net/core/dev.c:5148
__netif_receive_skb+0x2c/0x1d0 net/core/dev.c:5262
process_backlog+0x206/0x750 net/core/dev.c:6093
napi_poll net/core/dev.c:6530 [inline]
net_rx_action+0x508/0x1120 net/core/dev.c:6598
__do_softirq+0x262/0x98c kernel/softirq.c:292
run_ksoftirqd kernel/softirq.c:603 [inline]
run_ksoftirqd+0x8e/0x110 kernel/softirq.c:595
smpboot_thread_fn+0x6a3/0xa40 kernel/smpboot.c:165
kthread+0x361/0x430 kernel/kthread.c:255
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
Allocated by task 10091:
save_stack+0x23/0x90 mm/kasan/common.c:72
set_track mm/kasan/common.c:80 [inline]
__kasan_kmalloc mm/kasan/common.c:513 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:486
kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:521
slab_post_alloc_hook mm/slab.h:584 [inline]
slab_alloc_node mm/slab.c:3263 [inline]
kmem_cache_alloc_node+0x138/0x740 mm/slab.c:3575
__alloc_skb+0xd5/0x5e0 net/core/skbuff.c:198
alloc_skb_fclone include/linux/skbuff.h:1099 [inline]
sk_stream_alloc_skb net/ipv4/tcp.c:875 [inline]
sk_stream_alloc_skb+0x113/0xc90 net/ipv4/tcp.c:852
tcp_sendmsg_locked+0xcf9/0x3470 net/ipv4/tcp.c:1282
tcp_sendmsg+0x30/0x50 net/ipv4/tcp.c:1432
inet_sendmsg+0x9e/0xe0 net/ipv4/af_inet.c:807
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:672
__sys_sendto+0x262/0x380 net/socket.c:1998
__do_sys_sendto net/socket.c:2010 [inline]
__se_sys_sendto net/socket.c:2006 [inline]
__x64_sys_sendto+0xe1/0x1a0 net/socket.c:2006
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 10095:
save_stack+0x23/0x90 mm/kasan/common.c:72
set_track mm/kasan/common.c:80 [inline]
kasan_set_free_info mm/kasan/common.c:335 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:474
kasan_slab_free+0xe/0x10 mm/kasan/common.c:483
__cache_free mm/slab.c:3426 [inline]
kmem_cache_free+0x86/0x320 mm/slab.c:3694
kfree_skbmem+0x178/0x1c0 net/core/skbuff.c:645
__kfree_skb+0x1e/0x30 net/core/skbuff.c:681
sk_eat_skb include/net/sock.h:2453 [inline]
tcp_recvmsg+0x1252/0x2930 net/ipv4/tcp.c:2166
inet_recvmsg+0x136/0x610 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:886 [inline]
sock_recvmsg net/socket.c:904 [inline]
sock_recvmsg+0xce/0x110 net/socket.c:900
__sys_recvfrom+0x1ff/0x350 net/socket.c:2055
__do_sys_recvfrom net/socket.c:2073 [inline]
__se_sys_recvfrom net/socket.c:2069 [inline]
__x64_sys_recvfrom+0xe1/0x1a0 net/socket.c:2069
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff8880a488d040
which belongs to the cache skbuff_fclone_cache of size 456
The buggy address is located 40 bytes inside of
456-byte region [ffff8880a488d040, ffff8880a488d208)
The buggy address belongs to the page:
page:ffffea0002922340 refcount:1 mapcount:0 mapping:ffff88821b057000 index:0x0
raw: 00fffe0000000200 ffffea00022a5788 ffffea0002624a48 ffff88821b057000
raw: 0000000000000000 ffff8880a488d040 0000000100000006 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880a488cf00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8880a488cf80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8880a488d000: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
^
ffff8880a488d080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880a488d100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 853697504d ("tcp: Fix highest_sack and highest_sack_seq")
Fixes: 50895b9de1 ("tcp: highest_sack fix")
Fixes: 737ff31456 ("tcp: use sequence distance to detect reordering")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cambda Zhu <cambda@linux.alibaba.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d39ca2590d ]
This reverts commit 0d4a6608f6.
Willem reported that after commit 0d4a6608f6 ("udp: do rmem bulk
free even if the rx sk queue is empty") the memory allocated by
an almost idle system with many UDP sockets can grow a lot.
For stable kernel keep the solution as simple as possible and revert
the offending commit.
Reported-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 0d4a6608f6 ("udp: do rmem bulk free even if the rx sk queue is empty")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce896476c6 ]
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb626bf566 ]
Netdev_register_kobject is calling device_initialize. In case of error
reference taken by device_initialize is not given up.
Drivers are supposed to call free_netdev in case of error. In non-error
case the last reference is given up there and device release sequence
is triggered. In error case this reference is kept and the release
sequence is never started.
Fix this by setting reg_state as NETREG_UNREGISTERED if registering
fails.
This is the rootcause for couple of memory leaks reported by Syzkaller:
BUG: memory leak unreferenced object 0xffff8880675ca008 (size 256):
comm "netdev_register", pid 281, jiffies 4294696663 (age 6.808s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<0000000058ca4711>] kmem_cache_alloc_trace+0x167/0x280
[<000000002340019b>] device_add+0x882/0x1750
[<000000001d588c3a>] netdev_register_kobject+0x128/0x380
[<0000000011ef5535>] register_netdevice+0xa1b/0xf00
[<000000007fcf1c99>] __tun_chr_ioctl+0x20d5/0x3dd0
[<000000006a5b7b2b>] tun_chr_ioctl+0x2f/0x40
[<00000000f30f834a>] do_vfs_ioctl+0x1c7/0x1510
[<00000000fba062ea>] ksys_ioctl+0x99/0xb0
[<00000000b1c1b8d2>] __x64_sys_ioctl+0x78/0xb0
[<00000000984cabb9>] do_syscall_64+0x16f/0x580
[<000000000bde033d>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<00000000e6ca2d9f>] 0xffffffffffffffff
BUG: memory leak
unreferenced object 0xffff8880668ba588 (size 8):
comm "kobject_set_nam", pid 286, jiffies 4294725297 (age 9.871s)
hex dump (first 8 bytes):
6e 72 30 00 cc be df 2b nr0....+
backtrace:
[<00000000a322332a>] __kmalloc_track_caller+0x16e/0x290
[<00000000236fd26b>] kstrdup+0x3e/0x70
[<00000000dd4a2815>] kstrdup_const+0x3e/0x50
[<0000000049a377fc>] kvasprintf_const+0x10e/0x160
[<00000000627fc711>] kobject_set_name_vargs+0x5b/0x140
[<0000000019eeab06>] dev_set_name+0xc0/0xf0
[<0000000069cb12bc>] netdev_register_kobject+0xc8/0x320
[<00000000f2e83732>] register_netdevice+0xa1b/0xf00
[<000000009e1f57cc>] __tun_chr_ioctl+0x20d5/0x3dd0
[<000000009c560784>] tun_chr_ioctl+0x2f/0x40
[<000000000d759e02>] do_vfs_ioctl+0x1c7/0x1510
[<00000000351d7c31>] ksys_ioctl+0x99/0xb0
[<000000008390040a>] __x64_sys_ioctl+0x78/0xb0
[<0000000052d196b7>] do_syscall_64+0x16f/0x580
[<0000000019af9236>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<00000000bc384531>] 0xffffffffffffffff
v3 -> v4:
Set reg_state to NETREG_UNREGISTERED if registering fails
v2 -> v3:
* Replaced BUG_ON with WARN_ON in free_netdev and netdev_release
v1 -> v2:
* Relying on driver calling free_netdev rather than calling
put_device directly in error path
Reported-by: syzbot+ad8ca40ecd77896d51e2@syzkaller.appspotmail.com
Cc: David Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8eb718348 upstream.
kobject_init_and_add takes reference even when it fails. This has
to be given up by the caller in error handling. Otherwise memory
allocated by kobject_init_and_add is never freed. Originally found
by Syzkaller:
BUG: memory leak
unreferenced object 0xffff8880679f8b08 (size 8):
comm "netdev_register", pid 269, jiffies 4294693094 (age 12.132s)
hex dump (first 8 bytes):
72 78 2d 30 00 36 20 d4 rx-0.6 .
backtrace:
[<000000008c93818e>] __kmalloc_track_caller+0x16e/0x290
[<000000001f2e4e49>] kvasprintf+0xb1/0x140
[<000000007f313394>] kvasprintf_const+0x56/0x160
[<00000000aeca11c8>] kobject_set_name_vargs+0x5b/0x140
[<0000000073a0367c>] kobject_init_and_add+0xd8/0x170
[<0000000088838e4b>] net_rx_queue_update_kobjects+0x152/0x560
[<000000006be5f104>] netdev_register_kobject+0x210/0x380
[<00000000e31dab9d>] register_netdevice+0xa1b/0xf00
[<00000000f68b2465>] __tun_chr_ioctl+0x20d5/0x3dd0
[<000000004c50599f>] tun_chr_ioctl+0x2f/0x40
[<00000000bbd4c317>] do_vfs_ioctl+0x1c7/0x1510
[<00000000d4c59e8f>] ksys_ioctl+0x99/0xb0
[<00000000946aea81>] __x64_sys_ioctl+0x78/0xb0
[<0000000038d946e5>] do_syscall_64+0x16f/0x580
[<00000000e0aa5d8f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<00000000285b3d1a>] 0xffffffffffffffff
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0f4185160 ]
in the same manner as commit 690afc165b ("net: ip6_gre: fix moving
ip6gre between namespaces"), fix namespace moving as it was broken since
commit 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.").
Indeed, the ip6_gre commit removed the local flag for collect_md
condition, so there is no reason to keep it for ip_gre/ip_tunnel.
this patch will fix both ip_tunnel and ip_gre modules.
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: William Dauchy <w.dauchy@criteo.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5311a69aac ]
in the same manner as commit d0f4185160 ("net, ip_tunnel: fix
namespaces move"), fix namespace moving as it was broken since commit
8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnel"), but for
ipv6 this time; there is no reason to keep it for ip6_tunnel.
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnel")
Signed-off-by: William Dauchy <w.dauchy@criteo.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 690afc165b ]
Support for moving IPv4 GRE tunnels between namespaces was added in
commit b57708add3 ("gre: add x-netns support"). The respective change
for IPv6 tunnels, commit 22f08069e8 ("ip6gre: add x-netns support")
did not drop NETIF_F_NETNS_LOCAL flag so moving them from one netns to
another is still denied in IPv6 case. Drop NETIF_F_NETNS_LOCAL flag from
ip6gre tunnels to allow moving ip6gre tunnel endpoints between network
namespaces.
Signed-off-by: Niko Kortstrom <niko.kortstrom@nokia.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
