commit b8caf69a69 upstream.
Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16. Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.
The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds. This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:
Bluetooth: hci0: QCA Product ID :0x00000010
Bluetooth: hci0: QCA SOC Version :0x400a0200
Bluetooth: hci0: QCA ROM Version :0x00000200
Bluetooth: hci0: QCA Patch Version:0x00000d2b
Bluetooth: hci0: QCA controller version 0x02000200
Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
Bluetooth: hci0: QCA Failed to download patch (-2)
==================================================================
BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
Write of size 4 at addr ffff279347d578c0 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x8c/0xb8
print_report+0x188/0x488
kasan_report+0xb4/0x100
__asan_store4+0x80/0xa4
handle_rx_uart+0xa8/0x18c
qcom_geni_serial_handle_rx+0x84/0x9c
qcom_geni_serial_isr+0x24c/0x760
__handle_irq_event_percpu+0x108/0x500
handle_irq_event+0x6c/0x110
handle_fasteoi_irq+0x138/0x2cc
generic_handle_domain_irq+0x48/0x64
If the RX FIFO depth changes after probe, be sure to resize the buffer.
Fixes: f9d690b6ec ("tty: serial: qcom_geni_serial: Allocate port->rx_fifo buffer in probe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221221164022.1087814-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30b2b2196d upstream.
On async reads, page data is allocated before sending. When the
response is received but it has no data to fill (e.g.
STATUS_END_OF_FILE), __calc_signature() will still include the pages in
its computation, leading to an invalid signature check.
This patch fixes this by not setting the async read smb_rqst page data
(zeroed by default) if its got_bytes is 0.
This can be reproduced/verified with xfstests generic/465.
Cc: <stable@vger.kernel.org>
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7adbf9ada upstream.
If we have one task trying to start the quota rescan worker while another
one is trying to disable quotas, we can end up hitting a race that results
in the quota rescan worker doing a NULL pointer dereference. The steps for
this are the following:
1) Quotas are enabled;
2) Task A calls the quota rescan ioctl and enters btrfs_qgroup_rescan().
It calls qgroup_rescan_init() which returns 0 (success) and then joins a
transaction and commits it;
3) Task B calls the quota disable ioctl and enters btrfs_quota_disable().
It clears the bit BTRFS_FS_QUOTA_ENABLED from fs_info->flags and calls
btrfs_qgroup_wait_for_completion(), which returns immediately since the
rescan worker is not yet running.
Then it starts a transaction and locks fs_info->qgroup_ioctl_lock;
4) Task A queues the rescan worker, by calling btrfs_queue_work();
5) The rescan worker starts, and calls rescan_should_stop() at the start
of its while loop, which results in 0 iterations of the loop, since
the flag BTRFS_FS_QUOTA_ENABLED was cleared from fs_info->flags by
task B at step 3);
6) Task B sets fs_info->quota_root to NULL;
7) The rescan worker tries to start a transaction and uses
fs_info->quota_root as the root argument for btrfs_start_transaction().
This results in a NULL pointer dereference down the call chain of
btrfs_start_transaction(). The stack trace is something like the one
reported in Link tag below:
general protection fault, probably for non-canonical address 0xdffffc0000000041: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000208-0x000000000000020f]
CPU: 1 PID: 34 Comm: kworker/u4:2 Not tainted 6.1.0-syzkaller-13872-gb6bb9676f216 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Workqueue: btrfs-qgroup-rescan btrfs_work_helper
RIP: 0010:start_transaction+0x48/0x10f0 fs/btrfs/transaction.c:564
Code: 48 89 fb 48 (...)
RSP: 0018:ffffc90000ab7ab0 EFLAGS: 00010206
RAX: 0000000000000041 RBX: 0000000000000208 RCX: ffff88801779ba80
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
RBP: dffffc0000000000 R08: 0000000000000001 R09: fffff52000156f5d
R10: fffff52000156f5d R11: 1ffff92000156f5c R12: 0000000000000000
R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2bea75b718 CR3: 000000001d0cc000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
btrfs_qgroup_rescan_worker+0x3bb/0x6a0 fs/btrfs/qgroup.c:3402
btrfs_work_helper+0x312/0x850 fs/btrfs/async-thread.c:280
process_one_work+0x877/0xdb0 kernel/workqueue.c:2289
worker_thread+0xb14/0x1330 kernel/workqueue.c:2436
kthread+0x266/0x300 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
</TASK>
Modules linked in:
So fix this by having the rescan worker function not attempt to start a
transaction if it didn't do any rescan work.
Reported-by: syzbot+96977faa68092ad382c4@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/000000000000e5454b05f065a803@google.com/
Fixes: e804861bd4 ("btrfs: fix deadlock between quota disable and qgroup rescan worker")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2efb6edd52 upstream.
(Actually, this is fixing the "Read the Current Status" command sent to
the device's outgoing mailbox, but it is only currently used for the PWM
instructions.)
The PCI-1760 is operated mostly by sending commands to a set of Outgoing
Mailbox registers, waiting for the command to complete, and reading the
result from the Incoming Mailbox registers. One of these commands is
the "Read the Current Status" command. The number of this command is
0x07 (see the User's Manual for the PCI-1760 at
<https://advdownload.advantech.com/productfile/Downloadfile2/1-11P6653/PCI-1760.pdf>.
The `PCI1760_CMD_GET_STATUS` macro defined in the driver should expand
to this command number 0x07, but unfortunately it currently expands to
0x03. (Command number 0x03 is not defined in the User's Manual.)
Correct the definition of the `PCI1760_CMD_GET_STATUS` macro to fix it.
This is used by all the PWM subdevice related instructions handled by
`pci1760_pwm_insn_config()` which are probably all broken. The effect
of sending the undefined command number 0x03 is not known.
Fixes: 14b93bb6bb ("staging: comedi: adv_pci_dio: separate out PCI-1760 support")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20230103143754.17564-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7171b0e261 upstream.
The Texas Instruments TUSB8041 has an autosuspend problem at high
temperature.
If there is not USB traffic, after a couple of ms, the device enters in
autosuspend mode. In this condition the external clock stops working, to
save energy. When the USB activity turns on, ther hub exits the
autosuspend state, the clock starts running again and all works fine.
At ambient temperature all works correctly, but at high temperature,
when the USB activity turns on, the external clock doesn't restart and
the hub disappears from the USB bus.
Disabling the autosuspend mode for this hub solves the issue.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20221219124759.3207032-1-f.suligoi@asem.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96b328d119 upstream.
It is possible that in between calling fastrpc_map_get() until
map->fl->lock is taken in fastrpc_free_map(), another thread can call
fastrpc_map_lookup() and get a reference to a map that is about to be
deleted.
Rewrite fastrpc_map_get() to only increase the reference count of a map
if it's non-zero. Propagate this to callers so they can know if a map is
about to be deleted.
Fixes this warning:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 5 PID: 10100 at lib/refcount.c:25 refcount_warn_saturate
...
Call trace:
refcount_warn_saturate
[fastrpc_map_get inlined]
[fastrpc_map_lookup inlined]
fastrpc_map_create
fastrpc_internal_invoke
fastrpc_device_ioctl
__arm64_sys_ioctl
invoke_syscall
Fixes: c68cfb718c ("misc: fastrpc: Add support for context Invoke method")
Cc: stable <stable@kernel.org>
Signed-off-by: Ola Jeppsson <ola@snap.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221124174941.418450-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d83299351 upstream.
gcc-13 notices a type mismatch between function declaration
and definition for a few functions that have been converted
from returning vchiq specific status values to regular error
codes:
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:662:5: error: conflicting types for 'vchiq_initialise' due to enum/integer mismatch; have 'int(struct vchiq_instance **)' [-Werror=enum-int-mismatch]
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:1411:1: error: conflicting types for 'vchiq_use_internal' due to enum/integer mismatch; have 'int(struct vchiq_state *, struct vchiq_service *, enum USE_TYPE_E)' [-Werror=enum-int-mismatch]
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:1468:1: error: conflicting types for 'vchiq_release_internal' due to enum/integer mismatch; have 'int(struct vchiq_state *, struct vchiq_service *)' [-Werror=enum-int-mismatch]
Change the declarations to match the actual function definition.
Fixes: a9fbd828be ("staging: vchiq_arm: drop enum vchiq_status from vchiq_*_internal")
Cc: stable <stable@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230117163957.1109872-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7397906057 upstream.
do_prlimit() adds the user-controlled resource value to a pointer that
will subsequently be dereferenced. In order to help prevent this
codepath from being used as a spectre "gadget" a barrier needs to be
added after checking the range.
Reported-by: Jordy Zomer <jordyzomer@google.com>
Tested-by: Jordy Zomer <jordyzomer@google.com>
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74622f0a81 upstream.
USB3 ports on xHC hosts may have retimers that cause too long
exit latency to work with native USB3 U1/U2 link power management states.
For now only use usb_acpi_port_lpm_incapable() to evaluate if port lpm
should be disabled while setting up the USB3 roothub.
Other ways to identify lpm incapable ports can be added here later if
ACPI _DSM does not exist.
Limit this to Intel hosts for now, this is to my knowledge only
an Intel issue.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0522b9a165 upstream.
One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23a3b8d5a2 upstream.
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2bc47c43e upstream.
Make sure xhci_free_dev() and xhci_kill_endpoint_urbs() do not race
and cause null pointer dereference when host suddenly dies.
Usb core may call xhci_free_dev() which frees the xhci->devs[slot_id]
virt device at the same time that xhci_kill_endpoint_urbs() tries to
loop through all the device's endpoints, checking if there are any
cancelled urbs left to give back.
hold the xhci spinlock while freeing the virt device
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8fb5bc76e upstream.
When the host controller is not responding, all URBs queued to all
endpoints need to be killed. This can cause a kernel panic if we
dereference an invalid endpoint.
Fix this by using xhci_get_virt_ep() helper to find the endpoint and
checking if the endpoint is valid before dereferencing it.
[233311.853271] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead
[233311.853393] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
[233311.853964] pc : xhci_hc_died+0x10c/0x270
[233311.853971] lr : xhci_hc_died+0x1ac/0x270
[233311.854077] Call trace:
[233311.854085] xhci_hc_died+0x10c/0x270
[233311.854093] xhci_stop_endpoint_command_watchdog+0x100/0x1a4
[233311.854105] call_timer_fn+0x50/0x2d4
[233311.854112] expire_timers+0xac/0x2e4
[233311.854118] run_timer_softirq+0x300/0xabc
[233311.854127] __do_softirq+0x148/0x528
[233311.854135] irq_exit+0x194/0x1a8
[233311.854143] __handle_domain_irq+0x164/0x1d0
[233311.854149] gic_handle_irq.22273+0x10c/0x188
[233311.854156] el1_irq+0xfc/0x1a8
[233311.854175] lpm_cpuidle_enter+0x25c/0x418 [msm_pm]
[233311.854185] cpuidle_enter_state+0x1f0/0x764
[233311.854194] do_idle+0x594/0x6ac
[233311.854201] cpu_startup_entry+0x7c/0x80
[233311.854209] secondary_start_kernel+0x170/0x198
Fixes: 50e8725e7c ("xhci: Refactor command watchdog and fix split string.")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <0fe978ed-8269-9774-1c40-f8a98c17e838@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4aec40015 upstream.
There is a slight optimisation to be had by calculating the correct pos
pointer inside io_kiocb_update_pos and then using that later.
It seems code size drops by a bit:
000000000000a1b0 0000000000000400 t io_read
000000000000a5b0 0000000000000319 t io_write
vs
000000000000a1b0 00000000000003f6 t io_read
000000000000a5b0 0000000000000310 t io_write
Signed-off-by: Dylan Yudaken <dylany@fb.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d34e1e5b39 upstream.
Update kiocb->ki_pos at execution time rather than in io_prep_rw().
io_prep_rw() happens before the job is enqueued to a worker and so the
offset might be read multiple times before being executed once.
Ensures that the file position in a set of _linked_ SQEs will be only
obtained after earlier SQEs have completed, and so will include their
incremented file position.
Signed-off-by: Dylan Yudaken <dylany@fb.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit af9c45eceb upstream.
io_kiocb_ppos is called in both branches, and it seems that the compiler
does not fuse this. Fusing removes a few bytes from loop_rw_iter.
Before:
$ nm -S fs/io_uring.o | grep loop_rw_iter
0000000000002430 0000000000000124 t loop_rw_iter
After:
$ nm -S fs/io_uring.o | grep loop_rw_iter
0000000000002430 000000000000010d t loop_rw_iter
Signed-off-by: Dylan Yudaken <dylany@fb.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e775f93f2a upstream.
io_uring caches task references to avoid doing atomics for each of them
per request. If a request is put from the same task that allocated it,
then we can maintain a per-ctx cache of them. This obviously relies
on io_uring always pruning caches in a reliable way, and there's
currently a case off io_uring fd release where we can miss that.
One example is a ring setup with IOPOLL, which relies on the task
polling for completions, which will free them. However, if such a task
submits a request and then exits or closes the ring without reaping
the completion, then ring release will reap and put. If release happens
from that very same task, the completed request task refs will get
put back into the cache pool. This is problematic, as we're now beyond
the point of pruning caches.
Manually drop these caches after doing an IOPOLL reap. This releases
references from the current task, which is enough. If another task
happens to be doing the release, then the caching will not be
triggered and there's no issue.
Cc: stable@vger.kernel.org
Fixes: e98e49b2bb ("io_uring: extend task put optimisations")
Reported-by: Homin Rhee <hominlab@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 544d163d65 upstream.
syzbot reports an issue with overflow filling for IOPOLL:
WARNING: CPU: 0 PID: 28 at io_uring/io_uring.c:734 io_cqring_event_overflow+0x1c0/0x230 io_uring/io_uring.c:734
CPU: 0 PID: 28 Comm: kworker/u4:1 Not tainted 6.2.0-rc3-syzkaller-16369-g358a161a6a9e #0
Workqueue: events_unbound io_ring_exit_work
Call trace:
io_cqring_event_overflow+0x1c0/0x230 io_uring/io_uring.c:734
io_req_cqe_overflow+0x5c/0x70 io_uring/io_uring.c:773
io_fill_cqe_req io_uring/io_uring.h:168 [inline]
io_do_iopoll+0x474/0x62c io_uring/rw.c:1065
io_iopoll_try_reap_events+0x6c/0x108 io_uring/io_uring.c:1513
io_uring_try_cancel_requests+0x13c/0x258 io_uring/io_uring.c:3056
io_ring_exit_work+0xec/0x390 io_uring/io_uring.c:2869
process_one_work+0x2d8/0x504 kernel/workqueue.c:2289
worker_thread+0x340/0x610 kernel/workqueue.c:2436
kthread+0x12c/0x158 kernel/kthread.c:376
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:863
There is no real problem for normal IOPOLL as flush is also called with
uring_lock taken, but it's getting more complicated for IOPOLL|SQPOLL,
for which __io_cqring_overflow_flush() happens from the CQ waiting path.
Reported-and-tested-by: syzbot+6805087452d72929404e@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 343190841a ]
We only check the register opcode value inside the restricted ring
section, move it into the main io_uring_register() function instead
and check it up front.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a73825ba70 upstream.
Do not set REQ_F_NOWAIT if the socket is non blocking. When enabled this
causes the accept to immediately post a CQE with EAGAIN, which means you
cannot perform an accept SQE on a NONBLOCK socket asynchronously.
By removing the flag if there is no pending accept then poll is armed as
usual and when a connection comes in the CQE is posted.
Signed-off-by: Dylan Yudaken <dylany@fb.com>
Link: https://lore.kernel.org/r/20220324143435.2875844-1-dylany@fb.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 10c873334f upstream.
We currently check REQ_F_POLLED before arming async poll for a
notification to retry. If it's set, then we don't allow poll and will
punt to io-wq instead. This is done to prevent a situation where a buggy
driver will repeatedly return that there's space/data available yet we
get -EAGAIN.
However, if we already transferred data, then it should be safe to rely
on poll again. Gate the check on whether or not REQ_F_PARTIAL_IO is
also set.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4c3c09439c upstream.
Like commit 7ba89d2af1 for recv/recvmsg, support MSG_WAITALL for the
send side. If this flag is set and we do a short send, retry for a
stream of seqpacket socket.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8a3e8ee564 upstream.
If we need to continue doing this IO, then we don't want a potentially
selected buffer recycled. Add a flag for that.
Set this for recv/recvmsg if they do partial IO.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7ba89d2af1 upstream.
We currently don't attempt to get the full asked for length even if
MSG_WAITALL is set, if we get a partial receive. If we do see a partial
receive, then just note how many bytes we did and return -EAGAIN to
get it retried.
The iov is advanced appropriately for the vector based case, and we
manually bump the buffer and remainder for the non-vector case.
Cc: stable@vger.kernel.org
Reported-by: Constantine Gavrilov <constantine.gavrilov@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 46a525e199 upstream.
This isn't a reliable mechanism to tell if we have task_work pending, we
really should be looking at whether we have any items queued. This is
problematic if forward progress is gated on running said task_work. One
such example is reading from a pipe, where the write side has been closed
right before the read is started. The fput() of the file queues TWA_RESUME
task_work, and we need that task_work to be run before ->release() is
called for the pipe. If ->release() isn't called, then the read will sit
forever waiting on data that will never arise.
Fix this by io_run_task_work() so it checks if we have task_work pending
rather than rely on TIF_NOTIFY_SIGNAL for that. The latter obviously
doesn't work for task_work that is queued without TWA_SIGNAL.
Reported-by: Christiano Haesbaert <haesbaert@haesbaert.org>
Cc: stable@vger.kernel.org
Link: https://github.com/axboe/liburing/issues/665
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 272970be3d ]
The driver shutdown callback (which sends EDL_SOC_RESET to the device
over serdev) should not be invoked when HCI device is not open (e.g. if
hci_dev_open_sync() failed), because the serdev and its TTY are not open
either. Also skip this step if device is powered off
(qca_power_shutdown()).
The shutdown callback causes use-after-free during system reboot with
Qualcomm Atheros Bluetooth:
Unable to handle kernel paging request at virtual address
0072662f67726fd7
...
CPU: 6 PID: 1 Comm: systemd-shutdow Tainted: G W
6.1.0-rt5-00325-g8a5f56bcfcca #8
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
tty_driver_flush_buffer+0x4/0x30
serdev_device_write_flush+0x24/0x34
qca_serdev_shutdown+0x80/0x130 [hci_uart]
device_shutdown+0x15c/0x260
kernel_restart+0x48/0xac
KASAN report:
BUG: KASAN: use-after-free in tty_driver_flush_buffer+0x1c/0x50
Read of size 8 at addr ffff16270c2e0018 by task systemd-shutdow/1
CPU: 7 PID: 1 Comm: systemd-shutdow Not tainted
6.1.0-next-20221220-00014-gb85aaf97fb01-dirty #28
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xdc/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x68/0x84
print_report+0x188/0x488
kasan_report+0xa4/0xf0
__asan_load8+0x80/0xac
tty_driver_flush_buffer+0x1c/0x50
ttyport_write_flush+0x34/0x44
serdev_device_write_flush+0x48/0x60
qca_serdev_shutdown+0x124/0x274
device_shutdown+0x1e8/0x350
kernel_restart+0x48/0xb0
__do_sys_reboot+0x244/0x2d0
__arm64_sys_reboot+0x54/0x70
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x44/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xbc/0x140
el0t_64_sync+0x190/0x194
Fixes: 7e7bbddd02 ("Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2be43abac5 ]
Currently qca_suspend() is relied on IBS mechanism. During
FW download and memory dump collections, IBS will be disabled.
In those cases, driver will allow suspend and still uses the
serdev port, which results to errors. Now added a wait timeout
if suspend is triggered during FW download and memory collections.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Stable-dep-of: 272970be3d ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e006ac3003 ]
After [1][2], if we catch exceptions due to EFI runtime service, we will
clear EFI_RUNTIME_SERVICES bit to disable EFI runtime service, then the
subsequent routine which invoke the EFI runtime service should fail.
But the userspace cat efivars through /sys/firmware/efi/efivars/ will stuck
and infinite loop calling read() due to efivarfs_file_read() return -EINTR.
The -EINTR is converted from EFI_ABORTED by efi_status_to_err(), and is
an improper return value in this situation, so let virt_efi_xxx() return
EFI_DEVICE_ERROR and converted to -EIO to invoker.
Cc: <stable@vger.kernel.org>
Fixes: 3425d934fc ("efi/x86: Handle page faults occurring while running EFI runtime services")
Fixes: 23715a26c8 ("arm64: efi: Recover from synchronous exceptions occurring in firmware")
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7633355e5c upstream.
If nilfs2 reads a corrupted disk image and tries to reads a b-tree node
block by calling __nilfs_btree_get_block() against an invalid virtual
block address, it returns -ENOENT because conversion of the virtual block
address to a disk block address fails. However, this return value is the
same as the internal code that b-tree lookup routines return to indicate
that the block being searched does not exist, so functions that operate on
that b-tree may misbehave.
When nilfs_btree_insert() receives this spurious 'not found' code from
nilfs_btree_do_lookup(), it misunderstands that the 'not found' check was
successful and continues the insert operation using incomplete lookup path
data, causing the following crash:
general protection fault, probably for non-canonical address
0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
...
RIP: 0010:nilfs_btree_get_nonroot_node fs/nilfs2/btree.c:418 [inline]
RIP: 0010:nilfs_btree_prepare_insert fs/nilfs2/btree.c:1077 [inline]
RIP: 0010:nilfs_btree_insert+0x6d3/0x1c10 fs/nilfs2/btree.c:1238
Code: bc 24 80 00 00 00 4c 89 f8 48 c1 e8 03 42 80 3c 28 00 74 08 4c 89
ff e8 4b 02 92 fe 4d 8b 3f 49 83 c7 28 4c 89 f8 48 c1 e8 03 <42> 80 3c
28 00 74 08 4c 89 ff e8 2e 02 92 fe 4d 8b 3f 49 83 c7 02
...
Call Trace:
<TASK>
nilfs_bmap_do_insert fs/nilfs2/bmap.c:121 [inline]
nilfs_bmap_insert+0x20d/0x360 fs/nilfs2/bmap.c:147
nilfs_get_block+0x414/0x8d0 fs/nilfs2/inode.c:101
__block_write_begin_int+0x54c/0x1a80 fs/buffer.c:1991
__block_write_begin fs/buffer.c:2041 [inline]
block_write_begin+0x93/0x1e0 fs/buffer.c:2102
nilfs_write_begin+0x9c/0x110 fs/nilfs2/inode.c:261
generic_perform_write+0x2e4/0x5e0 mm/filemap.c:3772
__generic_file_write_iter+0x176/0x400 mm/filemap.c:3900
generic_file_write_iter+0xab/0x310 mm/filemap.c:3932
call_write_iter include/linux/fs.h:2186 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x7dc/0xc50 fs/read_write.c:584
ksys_write+0x177/0x2a0 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
...
</TASK>
This patch fixes the root cause of this problem by replacing the error
code that __nilfs_btree_get_block() returns on block address conversion
failure from -ENOENT to another internal code -EINVAL which means that the
b-tree metadata is corrupted.
By returning -EINVAL, it propagates without glitches, and for all relevant
b-tree operations, functions in the upper bmap layer output an error
message indicating corrupted b-tree metadata via
nilfs_bmap_convert_error(), and code -EIO will be eventually returned as
it should be.
Link: https://lkml.kernel.org/r/000000000000bd89e205f0e38355@google.com
Link: https://lkml.kernel.org/r/20230105055356.8811-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+ede796cecd5296353515@syzkaller.appspotmail.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a608da3bd7 upstream.
Using REQ_OP_ZONE_APPEND operations for synchronous writes to sequential
files succeeds regardless of the zone write pointer position, as long as
the target zone is not full. This means that if an external (buggy)
application writes to the zone of a sequential file underneath the file
system, subsequent file write() operation will succeed but the file size
will not be correct and the file will contain invalid data written by
another application.
Modify zonefs_file_dio_append() to check the written sector of an append
write (returned in bio->bi_iter.bi_sector) and return -EIO if there is a
mismatch with the file zone wp offset field. This change triggers a call
to zonefs_io_error() and a zone check. Modify zonefs_io_error_cb() to
not expose the unexpected data after the current inode size when the
errors=remount-ro mode is used. Other error modes are correctly handled
already.
Fixes: 02ef12a663 ("zonefs: use REQ_OP_ZONE_APPEND for sync DIO")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
