[ Upstream commit 0a4c56c80f ]
Commit ef91bb196b ("kernel.h: Silence sparse warning in
lower_32_bits") caused new warnings to show in the fsldma driver, but
that commit was not to blame: it only exposed some very incorrect code
that tried to take the low 32 bits of an address.
That made no sense for multiple reasons, the most notable one being that
that code was intentionally limited to only 32-bit ppc builds, so "only
low 32 bits of an address" was completely nonsensical. There were no
high bits to mask off to begin with.
But even more importantly fropm a correctness standpoint, turning the
address into an integer then caused the subsequent address arithmetic to
be completely wrong too, and the "+1" actually incremented the address
by one, rather than by four.
Which again was incorrect, since the code was reading two 32-bit values
and trying to make a 64-bit end result of it all. Surprisingly, the
iowrite64() did not suffer from the same odd and incorrect model.
This code has never worked, but it's questionable whether anybody cared:
of the two users that actually read the 64-bit value (by way of some C
preprocessor hackery and eventually the 'get_cdar()' inline function),
one of them explicitly ignored the value, and the other one might just
happen to work despite the incorrect value being read.
This patch at least makes it not fail the build any more, and makes the
logic superficially sane. Whether it makes any difference to the code
_working_ or not shall remain a mystery.
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b67a468a4c ]
When amdgpu_display_modeset_create_props() fails, state and
state->context should be freed to prevent memleak. It's the
same when amdgpu_dm_audio_init() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef67d792a2 ]
[Why]
In dm_dp_aux_transfer() now, we forget to handle AUX_WR fail cases. We
suppose every write wil get done successfully and hence some AUX
commands might not sent out indeed.
[How]
Check if AUX_WR success. If not, retry it.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5896585512 ]
In `amdgpu_dm_update_backlight_caps()`, there is a local
`amdgpu_dm_backlight_caps` object that is filled in by
`amdgpu_acpi_get_backlight_caps()`. However, this object is
uninitialized before the call and hence the subsequent check for
aux_support can fail since it is not initialized by
`amdgpu_acpi_get_backlight_caps()` as well. This change initializes
this local `amdgpu_dm_backlight_caps` object to 0.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 168f09cdad ]
[Why]
These aren't stable on some platform configurations when driving
multiple displays, especially on higher resolution.
In particular the delay in asserting p-state and validating from
x86 outweights any power or performance benefit from the hardware
composition.
Under some configurations this will manifest itself as extreme stutter
or unresponsiveness especially when combined with cursor movement.
[How]
Disable these for now. Exposing overlays to userspace doesn't guarantee
that they'll be able to use them in any and all configurations and it's
part of the DRM contract to have userspace gracefully handle validation
failures when they occur.
Valdiation occurs as part of DC and this in particular affects RV, so
disable this in dcn10_global_validation.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acb19e17c5 ]
If we configured io timeout of nbd0 to 100s. Later after we
finished using it, we configured nbd0 again and set the io
timeout to 0. We expect it would timeout after 30 seconds
and keep retry. But in fact we could not change the timeout
when we set it to 0. the timeout is still the original 100s.
So change the timeout to default 30s when we set it to zero.
It also behaves same as commit 2da22da573 ("nbd: fix zero
cmd timeout handling v2").
It becomes more important if we were reconfigure a nbd device
and the io timeout it set to zero. Because it could take 30s
to detect the new socket and thus io could be completed more
quickly compared to 100s.
Signed-off-by: Hou Pu <houpu@bytedance.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fd5b25499 ]
After commit 92cc68e358 ("drm/vblank: Use
spin_(un)lock_irq() in drm_crtc_vblank_on()") omapdrm locking is broken:
WARNING: inconsistent lock state
5.8.0-rc2-00483-g92cc68e35863 #13 Tainted: G W
--------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
swapper/0/0 [HC1[1]:SC0[0]:HE0:SE1] takes:
ea98222c (&dev->event_lock#2){?.+.}-{2:2}, at: drm_handle_vblank+0x4c/0x520 [drm]
{HARDIRQ-ON-W} state was registered at:
trace_hardirqs_on+0x9c/0x1ec
_raw_spin_unlock_irq+0x20/0x58
omap_crtc_atomic_enable+0x54/0xa0 [omapdrm]
drm_atomic_helper_commit_modeset_enables+0x218/0x270 [drm_kms_helper]
omap_atomic_commit_tail+0x48/0xc4 [omapdrm]
commit_tail+0x9c/0x190 [drm_kms_helper]
drm_atomic_helper_commit+0x154/0x188 [drm_kms_helper]
drm_client_modeset_commit_atomic+0x228/0x268 [drm]
drm_client_modeset_commit_locked+0x60/0x1d0 [drm]
drm_client_modeset_commit+0x24/0x40 [drm]
drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0xa8 [drm_kms_helper]
drm_fb_helper_set_par+0x2c/0x5c [drm_kms_helper]
drm_fb_helper_hotplug_event.part.0+0xa0/0xbc [drm_kms_helper]
drm_kms_helper_hotplug_event+0x24/0x30 [drm_kms_helper]
output_poll_execute+0x1a8/0x1c0 [drm_kms_helper]
process_one_work+0x268/0x800
worker_thread+0x30/0x4e0
kthread+0x164/0x190
ret_from_fork+0x14/0x20
The reason for this is that omapdrm calls drm_crtc_vblank_on() while
holding event_lock taken with spin_lock_irq().
It is not clear why drm_crtc_vblank_on() and drm_crtc_vblank_get() are
called while holding event_lock. I don't see any problem with moving
those calls outside the lock, which is what this patch does.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819103021.440288-1-tomi.valkeinen@ti.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 496ceaf124 ]
Leases don't currently work correctly on kcephfs, as they are not broken
when caps are revoked. They could eventually be implemented similarly to
how we did them in libcephfs, but for now don't allow them.
[ idryomov: no need for simple_nosetlease() in ceph_dir_fops and
ceph_snapdir_fops ]
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0839152f8c ]
vmalloc can return different return code than NULL and a valid
pointer. We must validate it in order to dereference a non valid
pointer.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bce382a8bb ]
We must validate FW size in order not to corrupt memory in case
a malicious FW file will be present in system.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43906812ea ]
This has roughly the same effect as drm_atomic_helper_wait_for_vblanks(),
basically just ensuring that vblank accounting is enabled so that we get
valid timestamp/seqn on pageflip events.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d3b6a8d21 ]
Based on nvme spec, when keep alive timeout is set to zero
the keep-alive timer should be disabled.
Signed-off-by: Amit Engel <amit.engel@dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cecf7560f0 ]
clang static analysis reports this representative problem
applesmc.c:758:10: warning: 1st function call argument is an
uninitialized value
left = be16_to_cpu(*(__be16 *)(buffer + 6)) >> 2;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
buffer is filled by the earlier call
ret = applesmc_read_key(LIGHT_SENSOR_LEFT_KEY, ...
This problem is reported because a goto skips the status check.
Other similar problems use data from applesmc_read_key before checking
the status. So move the checks to before the use.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Henrik Rydberg <rydberg@bitmath.org>
Link: https://lore.kernel.org/r/20200820131932.10590-1-trix@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d5cbf5fe4 ]
Define shutdown callback for display drm driver,
so as to disable all the CRTCS when shutdown
notification is received by the driver.
This change will turn off the timing engine so
that no display transactions are requested
while mmu translations are getting disabled
during reboot sequence.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Changes in v2:
- Remove NULL check from msm_pdev_shutdown (Stephen Boyd)
- Change commit text to reflect when this issue
was uncovered (Sai Prakash Ranjan)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c978caf08 ]
Plane validation uses an API drm_calc_scale which will
return src/dst value as a scale ratio.
when viewing the range on a scale the values should fall in as
Upscale ratio < Unity scale < Downscale ratio for src/dst formula
Fix the min and max scale ratios to suit the API accordingly.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Kristian H. Kristensen <hoegsberg@google.com>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627a49975b ]
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. One Lenovo PixArt
mouse is already fixed. Got two references for 17ef:602e and three
references for 17ef:6019 misbehaving like this. Got one direct bug
report for 17ef:6093 from Wyatt Ward (wyatt8740). So add
HID_QUIRK_ALWAYS_POLL for all of them.
Link: https://github.com/sriemer/fix-linux-mouse issue 22
Signed-off-by: Sebastian Parschauer <s.parschauer@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3c58f73723 upstream.
(scatter|gather)_data_area() need to flush dcache after writing data to or
before reading data from a page in uio data area. The two routines are
able to handle data transfer to/from such a page in fragments and flush the
cache after each fragment was copied by calling the wrapper
tcmu_flush_dcache_range().
That means:
1) flush_dcache_page() can be called multiple times for the same page.
2) Calling flush_dcache_page() indirectly using the wrapper does not make
sense, because each call of the wrapper is for one single page only and
the calling routine already has the correct page pointer.
Change (scatter|gather)_data_area() such that, instead of calling
tcmu_flush_dcache_range() before/after each memcpy, it now calls
flush_dcache_page() before unmapping a page (when writing is complete for
that page) or after mapping a page (when starting to read the page).
After this change only calls to tcmu_flush_dcache_range() for addresses in
vmalloc'ed command ring are left over.
The patch was tested on ARM with kernel 4.19.118 and 5.7.2
Link: https://lore.kernel.org/r/20200618131632.32748-2-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Tested-by: Daniel Meyerholt <dxm523@gmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c4e0f2123 upstream.
1) If remaining ring space before the end of the ring is smaller then the
next cmd to write, tcmu writes a padding entry which fills the remaining
space at the end of the ring.
Then tcmu calls tcmu_flush_dcache_range() with the size of struct
tcmu_cmd_entry as data length to flush. If the space filled by the
padding was smaller then tcmu_cmd_entry, tcmu_flush_dcache_range() is
called for an address range reaching behind the end of the vmalloc'ed
ring.
tcmu_flush_dcache_range() in a loop calls
flush_dcache_page(virt_to_page(start)); for every page being part of the
range. On x86 the line is optimized out by the compiler, as
flush_dcache_page() is empty on x86.
But I assume the above can cause trouble on other architectures that
really have a flush_dcache_page(). For paddings only the header part of
an entry is relevant due to alignment rules the header always fits in
the remaining space, if padding is needed. So tcmu_flush_dcache_range()
can safely be called with sizeof(entry->hdr) as the length here.
2) After it has written a command to cmd ring, tcmu calls
tcmu_flush_dcache_range() using the size of a struct tcmu_cmd_entry as
data length to flush. But if a command needs many iovecs, the real size
of the command may be bigger then tcmu_cmd_entry, so a part of the
written command is not flushed then.
Link: https://lore.kernel.org/r/20200528193108.9085-1-bstroesser@ts.fujitsu.com
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71a7f8cb1c upstream.
AT instructions do a translation table walk and return the result, or
the fault in PAR_EL1. KVM uses these to find the IPA when the value is
not provided by the CPU in HPFAR_EL1.
If a translation table walk causes an external abort it is taken as an
exception, even if it was due to an AT instruction. (DDI0487F.a's D5.2.11
"Synchronous faults generated by address translation instructions")
While we previously made KVM resilient to exceptions taken due to AT
instructions, the device access causes mismatched attributes, and may
occur speculatively. Prevent this, by forbidding a walk through memory
described as device at stage2. Now such AT instructions will report a
stage2 fault.
Such a fault will cause KVM to restart the guest. If the AT instructions
always walk the page tables, but guest execution uses the translation cached
in the TLB, the guest can't make forward progress until the TLB entry is
evicted. This isn't a problem, as since commit 5dcd0fdbb4 ("KVM: arm64:
Defer guest entry when an asynchronous exception is pending"), KVM will
return to the host to process IRQs allowing the rest of the system to keep
running.
Cc: stable@vger.kernel.org # <v5.3: 5dcd0fdbb4 ("KVM: arm64: Defer guest entry when an asynchronous exception is pending")
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88a84ccccb upstream.
KVM doesn't expect any synchronous exceptions when executing, any such
exception leads to a panic(). AT instructions access the guest page
tables, and can cause a synchronous external abort to be taken.
The arm-arm is unclear on what should happen if the guest has configured
the hardware update of the access-flag, and a memory type in TCR_EL1 that
does not support atomic operations. B2.2.6 "Possible implementation
restrictions on using atomic instructions" from DDI0487F.a lists
synchronous external abort as a possible behaviour of atomic instructions
that target memory that isn't writeback cacheable, but the page table
walker may behave differently.
Make KVM robust to synchronous exceptions caused by AT instructions.
Add a get_user() style helper for AT instructions that returns -EFAULT
if an exception was generated.
While KVM's version of the exception table mixes synchronous and
asynchronous exceptions, only one of these can occur at each location.
Re-enter the guest when the AT instructions take an exception on the
assumption the guest will take the same exception. This isn't guaranteed
to make forward progress, as the AT instructions may always walk the page
tables, but guest execution may use the translation cached in the TLB.
This isn't a problem, as since commit 5dcd0fdbb4 ("KVM: arm64: Defer guest
entry when an asynchronous exception is pending"), KVM will return to the
host to process IRQs allowing the rest of the system to keep running.
Cc: stable@vger.kernel.org # <v5.3: 5dcd0fdbb4 ("KVM: arm64: Defer guest entry when an asynchronous exception is pending")
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9ee186bb7 upstream.
KVM has a one instruction window where it will allow an SError exception
to be consumed by the hypervisor without treating it as a hypervisor bug.
This is used to consume asynchronous external abort that were caused by
the guest.
As we are about to add another location that survives unexpected exceptions,
generalise this code to make it behave like the host's extable.
KVM's version has to be mapped to EL2 to be accessible on nVHE systems.
The SError vaxorcism code is a one instruction window, so has two entries
in the extable. Because the KVM code is copied for VHE and nVHE, we end up
with four entries, half of which correspond with code that isn't mapped.
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f232d9ec02 upstream.
As seen in the Vivante kernel driver, most GPUs with the BLT engine have
a broken TS cache flush. The workaround is to temporarily set the BLT
command to CLEAR_IMAGE, without actually executing the clear. Apparently
this state change is enough to trigger the required TS cache flush. As
the BLT engine is completely asychronous, we also need a few more stall
states to synchronize the flush with the frontend.
Root-caused-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Walter Lozano <walter.lozano@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35556bed83 upstream.
When calling into hid_map_usage(), the passed event code is
blindly stored as is, even if it doesn't fit in the associated bitmap.
This event code can come from a variety of sources, including devices
masquerading as input devices, only a bit more "programmable".
Instead of taking the event code at face value, check that it actually
fits the corresponding bitmap, and if it doesn't:
- spit out a warning so that we know which device is acting up
- NULLify the bitmap pointer so that we catch unexpected uses
Code paths that can make use of untrusted inputs can now check
that the mapping was indeed correct and bail out if not.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bce1305c0e upstream.
It appears that a ReportSize value of zero is legal, even if a bit
non-sensical. Most of the HID code seems to handle that gracefully,
except when computing the total size in bytes. When fed as input to
memset, this leads to some funky outcomes.
Detect the corner case and correctly compute the size.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4a42c82e9 upstream.
Redefine GZIP, BZIP2, LZOP variables as KGZIP, KBZIP2, KLZOP resp.
GZIP, BZIP2, LZOP env variables are reserved by the tools. The original
attempt to redefine them internally doesn't work in makefiles/scripts
intercall scenarios, e.g., "make GZIP=gzip bindeb-pkg" and results in
broken builds. There can be other broken build commands because of this,
so the universal solution is to use non-reserved env variables for the
compression tools.
Fixes: 8dfb61dcba ("kbuild: add variables for compression tools")
Signed-off-by: Denis Efremov <efremov@linux.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dfb61dcba upstream.
Allow user to use alternative implementations of compression tools,
such as pigz, pbzip2, pxz. For example, multi-threaded tools to
speed up the build:
$ make GZIP=pigz BZIP2=pbzip2
Variables _GZIP, _BZIP2, _LZOP are used internally because original env
vars are reserved by the tools. The use of GZIP in gzip tool is obsolete
since 2015. However, alternative implementations (e.g., pigz) still rely
on it. BZIP2, BZIP, LZOP vars are not obsolescent.
The credit goes to @grsecurity.
As a sidenote, for multi-threaded lzma, xz compression one can use:
$ export XZ_OPT="--threads=0"
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f276031b4e upstream.
This comment block explains why include/generated/compile.h is omitted,
but nothing about include/generated/autoconf.h, which might be more
difficult to understand. Add more comments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1463f74f49 upstream.
'pushd' ... 'popd' is the last bash-specific code in this script.
One way to avoid it is to run the code in a sub-shell.
With that addressed, you can run this script with sh.
I replaced $(BASH) with $(CONFIG_SHELL), and I changed the hashbang
to #!/bin/sh.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea79e5168b upstream.
This script copies headers by the cpio command twice; first from
srctree, and then from objtree. However, when we building in-tree,
we know the srctree and the objtree are the same. That is, all the
headers copied by the first cpio are overwritten by the second one.
Skip the first cpio when we are building in-tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e11773e76 upstream.
This script computes md5sum of headers in srctree and in objtree.
However, when we are building in-tree, we know the srctree and the
objtree are the same. That is, we end up with the same computation
twice. In fact, the first two lines of kernel/kheaders.md5 are always
the same for in-tree builds.
Unify the two md5sum calculations.
For in-tree builds ($building_out_of_srctree is empty), we check
only two directories, "include", and "arch/$SRCARCH/include".
For out-of-tree builds ($building_out_of_srctree is 1), we check
4 directories, "$srctree/include", "$srctree/arch/$SRCARCH/include",
"include", and "arch/$SRCARCH/include" since we know they are all
different.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a06635718 upstream.
The 'head' and 'tail' commands can take a file path directly.
So, you do not need to run 'cat'.
cat kernel/kheaders.md5 | head -1
... is equivalent to:
head -1 kernel/kheaders.md5
and the latter saves forking one process.
While I was here, I replaced 'head -1' with 'head -n 1'.
I also replaced '==' with '=' since we do not have a good reason to
use the bashism.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
