commit 9279c00fa4 upstream.
The X series Ingenic SoCs have a shadow GPIO group which is at a higher
offset than the other groups, and is used for all GPIO configuration.
The regmap did not take this offset into account and set max_register
too low, so the regmap API blocked writes to the shadow group, which
made the pinctrl driver unable to configure any pins.
Fix this by adding regmap access tables to the chip info. The way that
max_register was computed was also off by one, since max_register is an
inclusive bound, not an exclusive bound; this has been fixed.
Cc: stable@vger.kernel.org
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Fixes: 6626a76ef8 ("pinctrl: ingenic: Add .max_register in regmap_config")
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220317000740.1045204-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b5b4f85b0 upstream.
As bughunter reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=215709
f2fs may hang when mounting a fuzzed image, the dmesg shows as below:
__filemap_get_folio+0x3a9/0x590
pagecache_get_page+0x18/0x60
__get_meta_page+0x95/0x460 [f2fs]
get_checkpoint_version+0x2a/0x1e0 [f2fs]
validate_checkpoint+0x8e/0x2a0 [f2fs]
f2fs_get_valid_checkpoint+0xd0/0x620 [f2fs]
f2fs_fill_super+0xc01/0x1d40 [f2fs]
mount_bdev+0x18a/0x1c0
f2fs_mount+0x15/0x20 [f2fs]
legacy_get_tree+0x28/0x50
vfs_get_tree+0x27/0xc0
path_mount+0x480/0xaa0
do_mount+0x7c/0xa0
__x64_sys_mount+0x8b/0xe0
do_syscall_64+0x38/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is cp_pack_total_block_count field in checkpoint was fuzzed
to one, as calcuated, two cp pack block locates in the same block address,
so then read latter cp pack block, it will block on the page lock due to
the lock has already held when reading previous cp pack block, fix it by
adding sanity check for cp_pack_total_block_count.
Cc: stable@vger.kernel.org
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b622ffe1d9 upstream.
Ensure that we always initialise the 'xattr_support' field in struct
nfs_fsinfo, so that nfs_server_set_fsinfo() doesn't declare our NFSv2/v3
client to be capable of supporting the NFSv4.2 xattr protocol by setting
the NFS_CAP_XATTR capability.
This configuration can cause nfs_do_access() to set access mode bits
that are unsupported by the NFSv3 ACCESS call, which may confuse
spec-compliant servers.
Reported-by: Olga Kornievskaia <kolga@netapp.com>
Fixes: b78ef845c3 ("NFSv4.2: query the server for extended attribute support")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3848e96edf upstream.
xprt_destory() claims XPRT_LOCKED and then calls del_timer_sync().
Both xprt_unlock_connect() and xprt_release() call
->release_xprt()
which drops XPRT_LOCKED and *then* xprt_schedule_autodisconnect()
which calls mod_timer().
This may result in mod_timer() being called *after* del_timer_sync().
When this happens, the timer may fire long after the xprt has been freed,
and run_timer_softirq() will probably crash.
The pairing of ->release_xprt() and xprt_schedule_autodisconnect() is
always called under ->transport_lock. So if we take ->transport_lock to
call del_timer_sync(), we can be sure that mod_timer() will run first
(if it runs at all).
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f97ec5d75e upstream.
Allocating memory with kmalloc and GPF_DMA32 is not allowed, the
allocator will ignore the attribute.
Instead, use dma_alloc_coherent() API as we allocate a small amount of
memory to transfer firmware fragment to the ISH.
On Arcada chromebook, after the patch the warning:
"Unexpected gfp: 0x4 (GFP_DMA32). Fixing up to gfp: 0xcc0 (GFP_KERNEL). Fix your code!"
is gone. The ISH firmware is loaded properly and we can interact with
the ISH:
> ectool --name cros_ish version
...
Build info: arcada_ish_v2.0.3661+3c1a1c1ae0 2022-02-08 05:37:47 @localhost
Tool version: v2.0.12300-900b03ec7f 2022-02-08 10:01:48 @localhost
Fixes: commit 91b228107d ("HID: intel-ish-hid: ISH firmware loader client driver")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 590bfb57b2 upstream.
It is insecure to allow arbitrary hash algorithms and signature
encodings to be used with arbitrary signature algorithms. Notably,
ECDSA, ECRDSA, and SM2 all sign/verify raw hash values and don't
disambiguate between different hash algorithms like RSA PKCS#1 v1.5
padding does. Therefore, they need to be restricted to certain sets of
hash algorithms (ideally just one, but in practice small sets are used).
Additionally, the encoding is an integral part of modern signature
algorithms, and is not supposed to vary.
Therefore, tighten the checks of hash_algo and encoding done by
software_key_determine_akcipher().
Also rearrange the parameters to software_key_determine_akcipher() to
put the public_key first, as this is the most important parameter and it
often determines everything else.
Fixes: 299f561a66 ("x509: Add support for parsing x509 certs with ECDSA keys")
Fixes: 2155256396 ("X.509: support OSCCA SM2-with-SM3 certificate verification")
Fixes: 0d7a78643f ("crypto: ecrdsa - add EC-RDSA (GOST 34.10) algorithm")
Cc: stable@vger.kernel.org
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Vitaly Chikunov <vt@altlinux.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2abc9c246e upstream.
Most callers of public_key_verify_signature(), including most indirect
callers via verify_signature() as well as pkcs7_verify_sig_chain(),
don't check that public_key_signature::pkey_algo matches
public_key::pkey_algo. These should always match. However, a malicious
signature could intentionally declare an unintended algorithm. It is
essential that such signatures be rejected outright, or that the
algorithm of the *key* be used -- not the algorithm of the signature as
that would allow attackers to choose the algorithm used.
Currently, public_key_verify_signature() correctly uses the key's
algorithm when deciding which akcipher to allocate. That's good.
However, it uses the signature's algorithm when deciding whether to do
the first step of SM2, which is incorrect. Also, v4.19 and older
kernels used the signature's algorithm for the entire process.
Prevent such errors by making public_key_verify_signature() enforce that
the signature's algorithm (if given) matches the key's algorithm.
Also remove two checks of this done by callers, which are now redundant.
Cc: stable@vger.kernel.org
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Vitaly Chikunov <vt@altlinux.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c51abd9683 upstream.
In many cases, keyctl_pkey_params_get_2() is validating the user buffer
lengths against the wrong algorithm properties. Fix it to check against
the correct properties.
Probably this wasn't noticed before because for all asymmetric keys of
the "public_key" subtype, max_data_size == max_sig_size == max_enc_size
== max_dec_size. However, this isn't necessarily true for the
"asym_tpm" subtype (it should be, but it's not strictly validated). Of
course, future key types could have different values as well.
Fixes: 00d60fd3b9 ("KEYS: Provide keyctls to drive the new key type ops for asymmetric keys [ver #2]")
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a14b65d59 upstream.
Remove the spinlock around the tree traversal as we are calling possibly
sleeping functions.
We do not need a spinlock here as there will be no modifications to this
tree at this point.
This prevents warnings like this to occur in dmesg:
[ 653.774996] BUG: sleeping function called from invalid context at kernel/loc\
king/mutex.c:280
[ 653.775088] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1827, nam\
e: umount
[ 653.775152] preempt_count: 1, expected: 0
[ 653.775191] CPU: 0 PID: 1827 Comm: umount Tainted: G W OE 5.17.0\
-rc7-00006-g4eb628dd74df #135
[ 653.775195] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-\
1.fc33 04/01/2014
[ 653.775197] Call Trace:
[ 653.775199] <TASK>
[ 653.775202] dump_stack_lvl+0x34/0x44
[ 653.775209] __might_resched.cold+0x13f/0x172
[ 653.775213] mutex_lock+0x75/0xf0
[ 653.775217] ? __mutex_lock_slowpath+0x10/0x10
[ 653.775220] ? _raw_write_lock_irq+0xd0/0xd0
[ 653.775224] ? dput+0x6b/0x360
[ 653.775228] cifs_kill_sb+0xff/0x1d0 [cifs]
[ 653.775285] deactivate_locked_super+0x85/0x130
[ 653.775289] cleanup_mnt+0x32c/0x4d0
[ 653.775292] ? path_umount+0x228/0x380
[ 653.775296] task_work_run+0xd8/0x180
[ 653.775301] exit_to_user_mode_loop+0x152/0x160
[ 653.775306] exit_to_user_mode_prepare+0x89/0xd0
[ 653.775315] syscall_exit_to_user_mode+0x12/0x30
[ 653.775322] do_syscall_64+0x48/0x90
[ 653.775326] entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 187af6e98b44e5d8f25e1d41a92db138eb54416f ("cifs: fix handlecache and multiuser")
Reported-by: kernel test robot <oliver.sang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47178c7722 upstream.
In multiuser each individual user has their own tcon structure for the
share and thus their own handle for a cached directory.
When we umount such a share we much make sure to release the pinned down dentry
for each such tcon and not just the master tcon.
Otherwise we will get nasty warnings on umount that dentries are still in use:
[ 3459.590047] BUG: Dentry 00000000115c6f41{i=12000000019d95,n=/} still in use\
(2) [unmount of cifs cifs]
...
[ 3459.590492] Call Trace:
[ 3459.590500] d_walk+0x61/0x2a0
[ 3459.590518] ? shrink_lock_dentry.part.0+0xe0/0xe0
[ 3459.590526] shrink_dcache_for_umount+0x49/0x110
[ 3459.590535] generic_shutdown_super+0x1a/0x110
[ 3459.590542] kill_anon_super+0x14/0x30
[ 3459.590549] cifs_kill_sb+0xf5/0x104 [cifs]
[ 3459.590773] deactivate_locked_super+0x36/0xa0
[ 3459.590782] cleanup_mnt+0x131/0x190
[ 3459.590789] task_work_run+0x5c/0x90
[ 3459.590798] exit_to_user_mode_loop+0x151/0x160
[ 3459.590809] exit_to_user_mode_prepare+0x83/0xd0
[ 3459.590818] syscall_exit_to_user_mode+0x12/0x30
[ 3459.590828] do_syscall_64+0x48/0x90
[ 3459.590833] entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee1fee9005 upstream.
Setting PTRACE_O_SUSPEND_SECCOMP is supposed to be a highly privileged
operation because it allows the tracee to completely bypass all seccomp
filters on kernels with CONFIG_CHECKPOINT_RESTORE=y. It is only supposed to
be settable by a process with global CAP_SYS_ADMIN, and only if that
process is not subject to any seccomp filters at all.
However, while these permission checks were done on the PTRACE_SETOPTIONS
path, they were missing on the PTRACE_SEIZE path, which also sets
user-specified ptrace flags.
Move the permissions checks out into a helper function and let both
ptrace_attach() and ptrace_setoptions() call it.
Cc: stable@kernel.org
Fixes: 13c4a90119 ("seccomp: add ptrace options for suspend/resume")
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lkml.kernel.org/r/20220319010838.1386861-1-jannh@google.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10b74af310 upstream.
In commit 4e7cf74fa3 ("clk: fractional-divider: Export approximation
algorithm to the CCF users"), the code handling the rational best
approximation algorithm was replaced by a call to the core
clk_fractional_divider_general_approximation function which did the same
thing back then.
However, in commit 82f53f9ee5 ("clk: fractional-divider: Introduce
POWER_OF_TWO_PS flag"), this common code was made conditional on
CLK_FRAC_DIVIDER_POWER_OF_TWO_PS flag which was not added back to the
rockchip clock driver.
This broke the ltk050h3146w-a2 MIPI DSI display present on a PX30-based
downstream board.
Let's add the flag to the fractional divider flags so that the original
and intended behavior is brought back to the rockchip clock drivers.
Fixes: 82f53f9ee5 ("clk: fractional-divider: Introduce POWER_OF_TWO_PS flag")
Cc: stable@vger.kernel.org
Cc: Quentin Schulz <foss+kernel@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220131163224.708002-1-quentin.schulz@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14b457fdde upstream.
When a consumer calls iio_read_channel_processed() and no channel scale
is available, it's assumed that the scale is one and the raw value is
returned as expected.
On the other hand, if the consumer calls iio_convert_raw_to_processed()
the scaling factor requested by the consumer is not applied.
This for example causes the consumer to process mV when expecting uV.
Make sure to always apply the scaling factor requested by the consumer.
Fixes: adc8ec5ff1 ("iio: inkern: pass through raw values if no scaling")
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220108205319.2046348-3-liambeguin@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bca97ff95 upstream.
When a consumer calls iio_read_channel_processed() and the channel has
an integer scale, the scale channel scale is applied and the processed
value is returned as expected.
On the other hand, if the consumer calls iio_convert_raw_to_processed()
the scaling factor requested by the consumer is not applied.
This for example causes the consumer to process mV when expecting uV.
Make sure to always apply the scaling factor requested by the consumer.
Fixes: 48e44ce0f8 ("iio:inkern: Add function to read the processed value")
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220108205319.2046348-2-liambeguin@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea75a342ae upstream.
It's impossible to program a valid value for TRCCONFIGR.QE
when TRCIDR0.QSUPP==0b10. In that case the following is true:
Q element support is implemented, and only supports Q elements without
instruction counts. TRCCONFIGR.QE can only take the values 0b00 or 0b11.
Currently the low bit of QSUPP is checked to see if the low bit of QE can
be written to, but as you can see when QSUPP==0b10 the low bit is cleared
making it impossible to ever write the only valid value of 0b11 to QE.
0b10 would be written instead, which is a reserved QE value even for all
values of QSUPP.
The fix is to allow writing the low bit of QE for any non zero value of
QSUPP.
This change also ensures that the low bit is always set, even when the
user attempts to only set the high bit.
Signed-off-by: James Clark <james.clark@arm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Fixes: d8c6696208 ("coresight-etm4x: Controls pertaining to the reset, mode, pe and events")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220120113047.2839622-2-james.clark@arm.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed2d980503 upstream.
The MHI driver does not work on big endian architectures. The
controller never transitions into mission mode. This appears to be due
to the modem device expecting the various contexts and transfer rings to
have fields in little endian order in memory, but the driver constructs
them in native endianness.
Fix MHI event, channel and command contexts and TRE handling macros to
use explicit conversion to little endian. Mark fields in relevant
structures as little endian to document this requirement.
Fixes: a6e2e3522f ("bus: mhi: core: Add support for PM state transitions")
Fixes: 6cd330ae76 ("bus: mhi: core: Add support for ringing channel/event ring doorbells")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220301160308.107452-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05519b8589 upstream.
xhci_decode_ctrl_ctx() returns the untouched buffer as-is if both "drop"
and "add" parameters are zero.
Fix the function to return an empty string in that case.
It was not immediately clear from the possible call chains whether this
issue is currently actually triggerable or not.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 90d6d5731d ("xhci: Add tracing for input control context")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
commit 4843b4b5ec ("xhci: fix even more unsafe memory usage in xhci tracing")
Link: https://lore.kernel.org/r/20220303110903.1662404-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14073ce951 upstream.
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac1912 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c05e4cf6 upstream.
A race between system resume and device-initiated resume may result in
runtime PM imbalance on USB2 root hub. If a device-initiated resume
starts and system resume xhci_bus_resume() directs U0 before hub driver
sees the resuming device in RESUME state, device-initiated resume will
not be finished in xhci_handle_usb2_port_link_resume(). In this case,
usb_hcd_end_port_resume() call is missing.
This changes calls usb_hcd_end_port_resume() if resuming device reaches
U0 to keep runtime PM balance.
Fixes: a231ec41e6 ("xhci: refactor U0 link state handling in get_port_status")
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3105bc977d upstream.
xhci_decode_usbsts() is expected to return a zero-terminated string by
its only caller, xhci_stop_endpoint_command_watchdog(), which directly
logs the return value:
xhci_warn(xhci, "USBSTS:%s\n", xhci_decode_usbsts(str, usbsts));
However, if no recognized bits are set in usbsts, the function will
return without having called any sprintf() and therefore return an
untouched non-zero-terminated caller-provided buffer, causing garbage
to be output to log.
Fix that by always including the raw value in the output.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 9c1aa36efd ("xhci: Show host status when watchdog triggers and host is assumed dead.")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1892bf9067 upstream.
The kernel test robot found a problem with the ene_ub6250 subdriver in
usb-storage: It uses structures containing bitfields to represent
hardware bits in its SD_STATUS, MS_STATUS, and SM_STATUS bytes. This
is not safe; it presumes a particular bit ordering and it assumes the
compiler will not insert padding, neither of which is guaranteed.
This patch fixes the problem by changing the structures to simple u8
values, with the bitfields replaced by bitmask constants.
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YjOcbuU106UpJ/V8@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e0438f83d upstream.
The following sequence of operations results in a refcount warning:
1. Open device /dev/tpmrm.
2. Remove module tpm_tis_spi.
3. Write a TPM command to the file descriptor opened at step 1.
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1161 at lib/refcount.c:25 kobject_get+0xa0/0xa4
refcount_t: addition on 0; use-after-free.
Modules linked in: tpm_tis_spi tpm_tis_core tpm mdio_bcm_unimac brcmfmac
sha256_generic libsha256 sha256_arm hci_uart btbcm bluetooth cfg80211 vc4
brcmutil ecdh_generic ecc snd_soc_core crc32_arm_ce libaes
raspberrypi_hwmon ac97_bus snd_pcm_dmaengine bcm2711_thermal snd_pcm
snd_timer genet snd phy_generic soundcore [last unloaded: spi_bcm2835]
CPU: 3 PID: 1161 Comm: hold_open Not tainted 5.10.0ls-main-dirty #2
Hardware name: BCM2711
[<c0410c3c>] (unwind_backtrace) from [<c040b580>] (show_stack+0x10/0x14)
[<c040b580>] (show_stack) from [<c1092174>] (dump_stack+0xc4/0xd8)
[<c1092174>] (dump_stack) from [<c0445a30>] (__warn+0x104/0x108)
[<c0445a30>] (__warn) from [<c0445aa8>] (warn_slowpath_fmt+0x74/0xb8)
[<c0445aa8>] (warn_slowpath_fmt) from [<c08435d0>] (kobject_get+0xa0/0xa4)
[<c08435d0>] (kobject_get) from [<bf0a715c>] (tpm_try_get_ops+0x14/0x54 [tpm])
[<bf0a715c>] (tpm_try_get_ops [tpm]) from [<bf0a7d6c>] (tpm_common_write+0x38/0x60 [tpm])
[<bf0a7d6c>] (tpm_common_write [tpm]) from [<c05a7ac0>] (vfs_write+0xc4/0x3c0)
[<c05a7ac0>] (vfs_write) from [<c05a7ee4>] (ksys_write+0x58/0xcc)
[<c05a7ee4>] (ksys_write) from [<c04001a0>] (ret_fast_syscall+0x0/0x4c)
Exception stack(0xc226bfa8 to 0xc226bff0)
bfa0: 00000000 000105b4 00000003 beafe664 00000014 00000000
bfc0: 00000000 000105b4 000103f8 00000004 00000000 00000000 b6f9c000 beafe684
bfe0: 0000006c beafe648 0001056c b6eb6944
---[ end trace d4b8409def9b8b1f ]---
The reason for this warning is the attempt to get the chip->dev reference
in tpm_common_write() although the reference counter is already zero.
Since commit 8979b02aaf ("tpm: Fix reference count to main device") the
extra reference used to prevent a premature zero counter is never taken,
because the required TPM_CHIP_FLAG_TPM2 flag is never set.
Fix this by moving the TPM 2 character device handling from
tpm_chip_alloc() to tpm_add_char_device() which is called at a later point
in time when the flag has been set in case of TPM2.
Commit fdc915f7f7 ("tpm: expose spaces via a device link /dev/tpmrm<n>")
already introduced function tpm_devs_release() to release the extra
reference but did not implement the required put on chip->devs that results
in the call of this function.
Fix this by putting chip->devs in tpm_chip_unregister().
Finally move the new implementation for the TPM 2 handling into a new
function to avoid multiple checks for the TPM_CHIP_FLAG_TPM2 flag in the
good case and error cases.
Cc: stable@vger.kernel.org
Fixes: fdc915f7f7 ("tpm: expose spaces via a device link /dev/tpmrm<n>")
Fixes: 8979b02aaf ("tpm: Fix reference count to main device")
Co-developed-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b61343b50 upstream.
For various reasons based on the allocator behaviour and typical
use-cases at the time, when the max32_alloc_size optimisation was
introduced it seemed reasonable to couple the reset of the tracked
size to the update of cached32_node upon freeing a relevant IOVA.
However, since subsequent optimisations focused on helping genuine
32-bit devices make best use of even more limited address spaces, it
is now a lot more likely for cached32_node to be anywhere in a "full"
32-bit address space, and as such more likely for space to become
available from IOVAs below that node being freed.
At this point, the short-cut in __cached_rbnode_delete_update() really
doesn't hold up any more, and we need to fix the logic to reliably
provide the expected behaviour. We still want cached32_node to only move
upwards, but we should reset the allocation size if *any* 32-bit space
has become available.
Reported-by: Yunfei Wang <yf.wang@mediatek.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/033815732d83ca73b13c11485ac39336f15c3b40.1646318408.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cc: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61cc4534b6 upstream.
It was found that reading /proc/lockdep after a lockdep splat may
potentially cause an access to freed memory if lockdep_unregister_key()
is called after the splat but before access to /proc/lockdep [1]. This
is due to the fact that graph_lock() call in lockdep_unregister_key()
fails after the clearing of debug_locks by the splat process.
After lockdep_unregister_key() is called, the lock_name may be freed
but the corresponding lock_class structure still have a reference to
it. That invalid memory pointer will then be accessed when /proc/lockdep
is read by a user and a use-after-free (UAF) error will be reported if
KASAN is enabled.
To fix this problem, lockdep_unregister_key() is now modified to always
search for a matching key irrespective of the debug_locks state and
zap the corresponding lock class if a matching one is found.
[1] https://lore.kernel.org/lkml/77f05c15-81b6-bddd-9650-80d5f23fe330@i-love.sakura.ne.jp/
Fixes: 8b39adbee8 ("locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Cc: Cheng-Jui Wang <cheng-jui.wang@mediatek.com>
Link: https://lkml.kernel.org/r/20220103023558.1377055-1-longman@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c4debc443 ]
When building the vm selftests using clang, some errors are seen due to
having headers in the compilation command:
clang -Wall -I ../../../../usr/include -no-pie gup_test.c ../../../../mm/gup_test.h -lrt -lpthread -o .../tools/testing/selftests/vm/gup_test
clang: error: cannot specify -o when generating multiple output files
make[1]: *** [../lib.mk:146: .../tools/testing/selftests/vm/gup_test] Error 1
Rework to add the header files to LOCAL_HDRS before including ../lib.mk,
since the dependency is evaluated in '$(OUTPUT)/%:%.c $(LOCAL_HDRS)' in
file lib.mk.
Link: https://lkml.kernel.org/r/20220304000645.1888133-1-yosryahmed@google.com
Signed-off-by: Yosry Ahmed <yosryahmed@google.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
