[ Upstream commit d3566abb1a ]
In shutdown/reboot paths, the timer is not stopped:
qla2x00_shutdown
pci_device_shutdown
device_shutdown
kernel_restart_prepare
kernel_restart
sys_reboot
This causes lockups (on powerpc) when firmware config space access calls
are interrupted by smp_send_stop later in reboot.
Fixes: e30d175648 ("[SCSI] qla2xxx: Addition of shutdown callback handler.")
Link: https://lore.kernel.org/r/20191024063804.14538-1-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d482c7bb05 ]
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that an HCD will
crash or hang when trying to handle an URB for such an endpoint.
Currently the USB core does not check for endpoints having a maxpacket
value of 0. This patch adds a check, printing a warning and skipping
over any endpoints it catches.
Now, the USB spec does not rule out endpoints having maxpacket = 0.
But since they wouldn't have any practical use, there doesn't seem to
be any good reason for us to accept them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281050420.1485-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7d9874c6f ]
layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c20c89b04 ]
composite_dev_cleanup call from the failure of configfs_composite_bind
frees up the cdev->os_desc_req and cdev->req. If the previous calls of
bind and unbind is successful these will carry stale values.
Consider the below sequence of function calls:
configfs_composite_bind()
composite_dev_prepare()
- Allocate cdev->req, cdev->req->buf
composite_os_desc_req_prepare()
- Allocate cdev->os_desc_req, cdev->os_desc_req->buf
configfs_composite_unbind()
composite_dev_cleanup()
- free the cdev->os_desc_req->buf and cdev->req->buf
Next composition switch
configfs_composite_bind()
- If it fails goto err_comp_cleanup will call the
composite_dev_cleanup() function
composite_dev_cleanup()
- calls kfree up with the stale values of cdev->req->buf and
cdev->os_desc_req from the previous configfs_composite_bind
call. The free call on these stale values leads to double free.
Hence, Fix this issue by setting request and buffer pointer to NULL after
kfree.
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba3a1a915c ]
Fix interrupt storm generated by endpoints when working in FIFO mode.
The TX_COMPLETE interrupt is used only by control endpoints processing.
Do not enable it for other types of endpoints.
Fixes: 914a3f3b37 ("USB: add atmel_usba_udc driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c24b75e0f9 ]
syzbot reported the following issue :
BUG: KCSAN: data-race in update_defense_level / update_defense_level
read to 0xffffffff861a6260 of 4 bytes by task 3006 on cpu 1:
update_defense_level+0x621/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:177
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
write to 0xffffffff861a6260 of 4 bytes by task 7333 on cpu 0:
update_defense_level+0xa62/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:205
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7333 Comm: kworker/0:5 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events defense_work_handler
Indeed, old_secure_tcp is currently a static variable, while it
needs to be a per netns variable.
Fixes: a0840e2e16 ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fd103ccfe ]
The initial lpfc_desc_set_adisc implementation in commit
dea3101e0a ("lpfc: add Emulex FC driver version 8.0.28") enabled ADISC if
cfg_use_adisc && RSCN_MODE && FCP_2_DEVICE
In commit 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of
SLI-3") this changed to
(cfg_use_adisc && RSC_MODE) || FCP_2_DEVICE
and later in commit ffc954936b ("[SCSI] lpfc 8.3.13: FC Discovery Fixes
and enhancements.") to
(cfg_use_adisc && RSC_MODE) || (FCP_2_DEVICE && FCP_TARGET)
A customer reports that after a devloss, an ADISC failure is logged. It
turns out the ADISC flag is set even the user explicitly set lpfc_use_adisc
= 0.
[Sat Dec 22 22:55:58 2018] lpfc 0000:82:00.0: 2:(0):0203 Devloss timeout on WWPN 50:01:43:80:12:8e:40:20 NPort x05df00 Data: x82000000 x8 xa
[Sat Dec 22 23:08:20 2018] lpfc 0000:82:00.0: 2:(0):2755 ADISC failure DID:05DF00 Status:x9/x70000
[mkp: fixed Hannes' email]
Fixes: 92d7f7b0cd ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: James Smart <james.smart@broadcom.com>
Link: https://lore.kernel.org/r/20191022072112.132268-1-dwagner@suse.de
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7be142caab upstream.
The PCI Tegra controller conversion to a device tree configurable
driver in commit d1523b52bf ("PCI: tegra: Move PCIe driver
to drivers/pci/host") implied that code for the driver can be
compiled in for a kernel supporting multiple platforms.
Unfortunately, a blind move of the code did not check that some of the
quirks that were applied in arch/arm (eg enabling Relaxed Ordering on
all PCI devices - since the quirk hook erroneously matches PCI_ANY_ID
for both Vendor-ID and Device-ID) are now applied in all kernels that
compile the PCI Tegra controlled driver, DT and ACPI alike.
This is completely wrong, in that enablement of Relaxed Ordering is only
required by default in Tegra20 platforms as described in the Tegra20
Technical Reference Manual (available at
https://developer.nvidia.com/embedded/downloads#?search=tegra%202 in
Section 34.1, where it is mentioned that Relaxed Ordering bit needs to
be enabled in its root ports to avoid deadlock in hardware) and in the
Tegra30 platforms for the same reasons (unfortunately not documented
in the TRM).
There is no other strict requirement on PCI devices Relaxed Ordering
enablement on any other Tegra platforms or PCI host bridge driver.
Fix this quite upsetting situation by limiting the vendor and device IDs
to which the Relaxed Ordering quirk applies to the root ports in
question, reported above.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[lorenzo.pieralisi@arm.com: completely rewrote the commit log/fixes tag]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c92e5fbf4 upstream.
Add missing break statement to prevent the code for case
USB_PORT_FEAT_C_RESET falling through to the default case.
Addresses-Coverity-ID: 143155
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d79cda045e upstream.
This patch fixes possibility of dereference by NULLL pointer in "[PATCH
v5 1/3] usbip: vhci extension: modifications to vhci driver" which has
been merged to 4.9-rc1. It occurs when a URB with pointer to invalid
USB/IP device is enqueued in race condition against detach operation.
A pointer was passed to vdev_to_vhci() before NULL check.
In vdev_to_vhci(), there's a dereference by the pointer.
This patch moves vdev_to_vhci() after NULL check of the pointer.
Signed-off-by: Nobuo Iwata <nobuo.iwata@fujixerox.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 351e5d869e upstream.
Configfs abuses symlink(2). Unlike the normal filesystems, it
wants the target resolved at symlink(2) time, like link(2) would've
done. The problem is that ->symlink() is called with the parent
directory locked exclusive, so resolving the target inside the
->symlink() is easily deadlocked.
Short of really ugly games in sys_symlink() itself, all we can
do is to unlock the parent before resolving the target and
relock it after. However, that invalidates the checks done
by the caller of ->symlink(), so we have to
* check that dentry is still where it used to be
(it couldn't have been moved, but it could've been unhashed)
* recheck that it's still negative (somebody else
might've successfully created a symlink with the same name
while we were looking the target up)
* recheck the permissions on the parent directory.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0841eefd9 upstream.
Make sure that attribute methods are not called after the item
has been removed from the tree. To do so, we
* at the point of no return in removals, grab ->frag_sem
exclusive and mark the fragment dead.
* call the methods of attributes with ->frag_sem taken
shared and only after having verified that the fragment is still
alive.
The main benefit is for method instances - they are
guaranteed that the objects they are accessing *and* all ancestors
are still there. Another win is that we don't need to bother
with extra refcount on config_item when opening a file -
the item will be alive for as long as it stays in the tree, and
we won't touch it/attributes/any associated data after it's
been removed from the tree.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47320fbe11 upstream.
Refcounted, hangs of configfs_dirent, created by operations that add
fragments to configfs tree (mkdir and configfs_register_{subsystem,group}).
Will be used in the next commit to provide exclusion between fragment
removal and ->show/->store calls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f19e4ed1e1 upstream.
revert cc57c07343 "configfs: fix registered group removal"
It was an attempt to handle something that fundamentally doesn't
work - configfs_register_group() should never be done in a part
of tree that can be rmdir'ed. And in mainline it never had been,
so let's not borrow trouble; the fix was racy anyway, it would take
a lot more to make that work and desired semantics is not clear.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f6928c347 upstream.
Bool initializations should use true and false. Bool tests don't need
comparisons.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7a1337f0d upstream.
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org> # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de280f403f upstream.
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes: 46be265d33 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cb3eaac52 upstream.
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30b7244d79 upstream.
The copy_to_user() function returns the number of bytes remaining to be
copied. In this code, that positive return is checked at the end of the
function and we return zero/success. What we should do instead is
return -EFAULT.
Fixes: a7b4f989a6 ("netfilter: ipset: IP set core support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 250367c59e upstream.
Invoking the following commands on a 32-bit architecture with strict
alignment requirements (such as an ARMv7-based Raspberry Pi) results
in an alignment exception:
# nft add table ip test-ip4
# nft add chain ip test-ip4 output { type filter hook output priority 0; }
# nft add rule ip test-ip4 output quota 1025 bytes
Alignment trap: not handling instruction e1b26f9f at [<7f4473f8>]
Unhandled fault: alignment exception (0x001) at 0xb832e824
Internal error: : 1 [#1] PREEMPT SMP ARM
Hardware name: BCM2835
[<7f4473fc>] (nft_quota_do_init [nft_quota])
[<7f447448>] (nft_quota_init [nft_quota])
[<7f4260d0>] (nf_tables_newrule [nf_tables])
[<7f4168dc>] (nfnetlink_rcv_batch [nfnetlink])
[<7f416bd0>] (nfnetlink_rcv [nfnetlink])
[<8078b334>] (netlink_unicast)
[<8078b664>] (netlink_sendmsg)
[<8071b47c>] (sock_sendmsg)
[<8071bd18>] (___sys_sendmsg)
[<8071ce3c>] (__sys_sendmsg)
[<8071ce94>] (sys_sendmsg)
The reason is that nft_quota_do_init() calls atomic64_set() on an
atomic64_t which is only aligned to 32-bit, not 64-bit, because it
succeeds struct nft_expr in memory which only contains a 32-bit pointer.
Fix by aligning the nft_expr private data to 64-bit.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24e1eb5c0d upstream.
It could happen that either `val` or `val2` [provided from userspace] is
negative. In that case the computed frequency could get a weird value.
Fix this by checking that neither of the 2 variables is negative, and check
that the computed result is not-zero.
Fixes: e4f9593901 ("iio: imu: adis16480 switch sampling frequency attr to core support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea60ed6fcf upstream.
KASAN reports a use-after-free when running xfstest generic/531, with the
following trace:
[ 293.903362] kasan_report+0xe/0x20
[ 293.903365] rb_erase+0x1f/0x790
[ 293.903370] __ceph_remove_cap+0x201/0x370
[ 293.903375] __ceph_remove_caps+0x4b/0x70
[ 293.903380] ceph_evict_inode+0x4e/0x360
[ 293.903386] evict+0x169/0x290
[ 293.903390] __dentry_kill+0x16f/0x250
[ 293.903394] dput+0x1c6/0x440
[ 293.903398] __fput+0x184/0x330
[ 293.903404] task_work_run+0xb9/0xe0
[ 293.903410] exit_to_usermode_loop+0xd3/0xe0
[ 293.903413] do_syscall_64+0x1a0/0x1c0
[ 293.903417] entry_SYSCALL_64_after_hwframe+0x44/0xa9
This happens because __ceph_remove_cap() may queue a cap release
(__ceph_queue_cap_release) which can be scheduled before that cap is
removed from the inode list with
rb_erase(&cap->ci_node, &ci->i_caps);
And, when this finally happens, the use-after-free will occur.
This can be fixed by removing the cap from the inode list before being
removed from the session list, and thus eliminating the risk of an UAF.
Cc: stable@vger.kernel.org
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cbf2fff3b upstream.
In the current code, we use the atomic_cmpxchg() to serialize the output
of the dump_stack(), but this implementation suffers the thundering herd
problem. We have observed such kind of livelock on a Marvell cn96xx
board(24 cpus) when heavily using the dump_stack() in a kprobe handler.
Actually we can let the competitors to wait for the releasing of the
lock before jumping to atomic_cmpxchg(). This will definitely mitigate
the thundering herd problem. Thanks Linus for the suggestion.
[akpm@linux-foundation.org: fix comment]
Link: http://lkml.kernel.org/r/20191030031637.6025-1-haokexin@gmail.com
Fixes: b58d977432 ("dump_stack: serialize the output from dump_stack()")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 169226f7e0 upstream.
We have a usecase to use tmpfs as QEMU memory backend and we would like
to take the advantage of THP as well. But, our test shows the EPT is
not PMD mapped even though the underlying THP are PMD mapped on host.
The number showed by /sys/kernel/debug/kvm/largepage is much less than
the number of PMD mapped shmem pages as the below:
7f2778200000-7f2878200000 rw-s 00000000 00:14 262232 /dev/shm/qemu_back_mem.mem.Hz2hSf (deleted)
Size: 4194304 kB
[snip]
AnonHugePages: 0 kB
ShmemPmdMapped: 579584 kB
[snip]
Locked: 0 kB
cat /sys/kernel/debug/kvm/largepages
12
And some benchmarks do worse than with anonymous THPs.
By digging into the code we figured out that commit 127393fbe5 ("mm:
thp: kvm: fix memory corruption in KVM with THP enabled") checks if
there is a single PTE mapping on the page for anonymous THP when setting
up EPT map. But the _mapcount < 0 check doesn't work for page cache THP
since every subpage of page cache THP would get _mapcount inc'ed once it
is PMD mapped, so PageTransCompoundMap() always returns false for page
cache THP. This would prevent KVM from setting up PMD mapped EPT entry.
So we need handle page cache THP correctly. However, when page cache
THP's PMD gets split, kernel just remove the map instead of setting up
PTE map like what anonymous THP does. Before KVM calls get_user_pages()
the subpages may get PTE mapped even though it is still a THP since the
page cache THP may be mapped by other processes at the mean time.
Checking its _mapcount and whether the THP has PTE mapped or not.
Although this may report some false negative cases (PTE mapped by other
processes), it looks not trivial to make this accurate.
With this fix /sys/kernel/debug/kvm/largepage would show reasonable
pages are PMD mapped by EPT as the below:
7fbeaee00000-7fbfaee00000 rw-s 00000000 00:14 275464 /dev/shm/qemu_back_mem.mem.SKUvat (deleted)
Size: 4194304 kB
[snip]
AnonHugePages: 0 kB
ShmemPmdMapped: 557056 kB
[snip]
Locked: 0 kB
cat /sys/kernel/debug/kvm/largepages
271
And the benchmarks are as same as anonymous THPs.
[yang.shi@linux.alibaba.com: v4]
Link: http://lkml.kernel.org/r/1571865575-42913-1-git-send-email-yang.shi@linux.alibaba.com
Link: http://lkml.kernel.org/r/1571769577-89735-1-git-send-email-yang.shi@linux.alibaba.com
Fixes: dd78fedde4 ("rmap: support file thp")
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Reported-by: Gang Deng <gavin.dg@linux.alibaba.com>
Tested-by: Gang Deng <gavin.dg@linux.alibaba.com>
Suggested-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 706ad6746a upstream.
For Focusrite Saffire Pro i/o, the lowest 8 bits of register represents
configured source of sampling clock. The next lowest 8 bits represents
whether the configured source is actually detected or not just after
the register is changed for the source.
Current implementation evaluates whole the register to detect configured
source. This results in failure due to the next lowest 8 bits when the
source is connected in advance.
This commit fixes the bug.
Fixes: 25784ec2d0 ("ALSA: bebob: Add support for Focusrite Saffire/SaffirePro series")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191102150920.20367-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7af6307a8 upstream.
The clean up commit 41672c0c24 ("ALSA: timer: Simplify error path in
snd_timer_open()") unified the error handling code paths with the
standard goto, but it introduced a subtle bug: the timer instance is
stored in snd_timer_open() incorrectly even if it returns an error.
This may eventually lead to UAF, as spotted by fuzzer.
The culprit is the snd_timer_open() code checks the
SNDRV_TIMER_IFLG_EXCLUSIVE flag with the common variable timeri.
This variable is supposed to be the newly created instance, but we
(ab-)used it for a temporary check before the actual creation of a
timer instance. After that point, there is another check for the max
number of instances, and it bails out if over the threshold. Before
the refactoring above, it worked fine because the code returned
directly from that point. After the refactoring, however, it jumps to
the unified error path that stores the timeri variable in return --
even if it returns an error. Unfortunately this stored value is kept
in the caller side (snd_timer_user_tselect()) in tu->timeri. This
causes inconsistency later, as if the timer was successfully
assigned.
In this patch, we fix it by not re-using timeri variable but a
temporary variable for testing the exclusive connection, so timeri
remains NULL at that point.
Fixes: 41672c0c24 ("ALSA: timer: Simplify error path in snd_timer_open()")
Reported-and-tested-by: Tristan Madani <tristmd@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106165547.23518-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99a8efbb6e ]
The variable nfcid_skb is not changed in the callee nfc_hci_get_param()
if error occurs. Consequently, the freed variable nfcid_skb will be
freed again, resulting in a double free bug. Set nfcid_skb to NULL after
releasing it to fix the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 025ec40b81 ]
The function nfc_put_device(dev) is called twice to drop the reference
to dev when there is no associated local llcp. Remove one of them to fix
the bug.
Fixes: 52feb444a9 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support")
Fixes: d9b8d8e19b ("NFC: llcp: Service Name Lookup netlink interface")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 517ce4e933 ]
The address of fw_vsc_cfg is on stack. Releasing it with devm_kfree() is
incorrect, which may result in a system crash or other security impacts.
The expected object to free is *fw_vsc_cfg.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
