[ Upstream commit a96a33b1ca ]
For cases where there is a mismatch in ARMv8.2-LVA support between CPUs
we have to be careful in allowing secondary CPUs to boot if 52-bit
virtual addresses have already been enabled on the boot CPU.
This patch adds code to the secondary startup path. If the boot CPU has
enabled 52-bit VAs then ID_AA64MMFR2_EL1 is checked to see if the
secondary can also enable 52-bit support. If not, the secondary is
prevented from booting and an error message is displayed indicating why.
Technically this patch could be implemented using the cpufeature code
when considering 52-bit userspace support. However, we employ low level
checks here as the cpufeature code won't be able to run if we have
mismatched 52-bit kernel va support.
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4bff35ca1 ]
Show the hpa address of the HP SDC instead of a hashed value, e.g.:
HP SDC: HP SDC at 0xf0201000, IRQ 23 (NMI IRQ 24)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 785145171d ]
We want the hpa addresses printed in the serio modules, not some
virtual ioremap()ed address, e.g.:
serio: gsc-ps2-keyboard port at 0xf0108000 irq 22 @ 2:0:11
serio: gsc-ps2-mouse port at 0xf0108100 irq 22 @ 2:0:12
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 998a84c27a ]
imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.
Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c41ea57be ]
If debugging on i.MX is enabled DEBUG_IMX_UART_PORT defines which UART
is used for the debug output. If however debugging is off don't only
hide the then unused config item but drop it completely by using a
dependency instead of a conditional prompt.
This fixes DEBUG_IMX_UART_PORT being present in the kernel config even
if DEBUG_LL is disabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c4042a4d0 ]
When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.
Correct the wqe initializaton when both dif and first burst are used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24906a41ee ]
The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.
Fixes: daa5abc41c ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e9c523016 ]
There are two callers of this function and they both unlock the mutex so
this ends up being a double unlock.
Fixes: 44ed167da7 ("drbd: rcu_read_lock() and rcu_dereference() for tconn->net_conf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285531f9e6 ]
In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).
# iw wlan0 station get fc:ec:da:64:a6:dd
Station fc:ec:da:64:a6:dd (on wlan0)
inactive time: 4294894049 ms
.
.
connected time: 70 seconds
Fix by returning last_rx if last_ack == 0.
Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8731acc506 ]
gcc's -freorder-blocks-and-partition option makes it group frequently
and infrequently used code in .text.hot and .text.unlikely sections
respectively. At least when building modules on s390, this option is
used by default.
gdb assumes that all code is located in .text section, and that .text
section is located at module load address. With such modules this is no
longer the case: there is code in .text.hot and .text.unlikely, and
either of them might precede .text.
Fix by explicitly telling gdb the addresses of code sections.
It might be tempting to do this for all sections, not only the ones in
the white list. Unfortunately, gdb appears to have an issue, when
telling it about e.g. loadable .note.gnu.build-id section causes it to
think that non-loadable .note.Linux section is loaded at address 0,
which in turn causes NULL pointers to be resolved to bogus symbols. So
keep using the white list approach for the time being.
Link: http://lkml.kernel.org/r/20191028152734.13065-1-iii@linux.ibm.com
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kieran Bingham <kbingham@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c77734642 ]
The left time value is wrong when we get it by sysfs. The left time value
should be equal to preset timeout value minus elapsed time value. According
to the Meson-GXB/GXL datasheets which can be found at [0], the timeout value
is saved to BIT[0-15] of the WATCHDOG_TCNT, and elapsed time value is saved
to BIT[16-31] of the WATCHDOG_TCNT.
[0]: http://linux-meson.com
Fixes: 683fa50f0e ("watchdog: Add Meson GXBB Watchdog Driver")
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 128a1b87d3 ]
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c43eab3edd ]
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f430c7ed8b ]
Add a missing short description to the reset_control_ops documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[p.zabel@pengutronix.de: rebased and updated commit message]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9323b664c ]
Properly save and restore all top PLL related configuration registers
during suspend/resume cycle. So far driver only handled EPLL and RPLL
clocks, all other were reset to default values after suspend/resume cycle.
This caused for example lower G3D (MALI Panfrost) performance after system
resume, even if performance governor has been selected.
Reported-by: Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Fixes: 773424326b ("clk: samsung: exynos5420: add more registers to restore list")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 597b389bd8 which is
commit 50254256f3 upstream.
It breaks a number of runtime Android networking tests, so something is
wrong with the backport, or something else also needed to be backported
at the same time. So I'm dropping this from the tree as regressions are
not good.
Cc: David Barmann <david.barmann@stackpath.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af2e8c68b9 upstream.
On some systems that are vulnerable to Spectre v2, it is up to
software to flush the link stack (return address stack), in order to
protect against Spectre-RSB.
When exiting from a guest we do some house keeping and then
potentially exit to C code which is several stack frames deep in the
host kernel. We will then execute a series of returns without
preceeding calls, opening up the possiblity that the guest could have
poisoned the link stack, and direct speculative execution of the host
to a gadget of some sort.
To prevent this we add a flush of the link stack on exit from a guest.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[dja: straightforward backport to v4.14]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39e72bf96f upstream.
In commit ee13cb249f ("powerpc/64s: Add support for software count
cache flush"), I added support for software to flush the count
cache (indirect branch cache) on context switch if firmware told us
that was the required mitigation for Spectre v2.
As part of that code we also added a software flush of the link
stack (return address stack), which protects against Spectre-RSB
between user processes.
That is all correct for CPUs that activate that mitigation, which is
currently Power9 Nimbus DD2.3.
What I got wrong is that on older CPUs, where firmware has disabled
the count cache, we also need to flush the link stack on context
switch.
To fix it we create a new feature bit which is not set by firmware,
which tells us we need to flush the link stack. We set that when
firmware tells us that either of the existing Spectre v2 mitigations
are enabled.
Then we adjust the patching code so that if we see that feature bit we
enable the link stack flush. If we're also told to flush the count
cache in software then we fall through and do that also.
On the older CPUs we don't need to do do the software count cache
flush, firmware has disabled it, so in that case we patch in an early
return after the link stack flush.
The naming of some of the functions is awkward after this patch,
because they're called "count cache" but they also do link stack. But
we'll fix that up in a later commit to ease backporting.
This is the fix for CVE-2019-18660.
Reported-by: Anthony Steinhauser <asteinhauser@google.com>
Fixes: ee13cb249f ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[dja: straightforward backport to v4.14]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5618332e5b upstream.
The userspace comedilib function 'get_cmd_generic_timed' fills
the cmd structure with an informed guess and then calls the
function 'usbduxfast_ai_cmdtest' in this driver repeatedly while
'usbduxfast_ai_cmdtest' is modifying the cmd struct until it
no longer changes. However, because of rounding errors this never
converged because 'steps = (cmd->convert_arg * 30) / 1000' and then
back to 'cmd->convert_arg = (steps * 1000) / 30' won't be the same
because of rounding errors. 'Steps' should only be converted back to
the 'convert_arg' if 'steps' has actually been modified. In addition
the case of steps being 0 wasn't checked which is also now done.
Signed-off-by: Bernd Porr <mail@berndporr.me.uk>
Cc: <stable@vger.kernel.org> # 4.4+
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20191118230759.1727-1-mail@berndporr.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92fe35fb9c upstream.
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea422312a4 upstream.
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
Fixes: 0f64478cbc ("USB: add USB serial mos7720 driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e696d00e65 upstream.
Add USB ID for MOXA UPort 2210. This device contains mos7820 but
it passes GPIO0 check implemented by driver and it's detected as
mos7840. Hence product id check is added to force mos7820 mode.
Signed-off-by: Pavel Löbl <pavel@loebl.cz>
Cc: stable <stable@vger.kernel.org>
[ johan: rename id defines and add vendor-id check ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2055997f98 ]
We try to disable callbacks on c_ivq even without multiport
even though that vq is not initialized in this configuration.
Fixes: c743d09dbd ("virtio: console: Disable callbacks for virtqueues at start of S4 freeze")
Suggested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7728002c1 ]
Commit 780bc7903a ("virtio_ring: Support DMA APIs") makes
virtqueue_add() return -EIO when we fail to map our I/O buffers. This is
a very realistic scenario for guests with encrypted memory, as swiotlb
may run out of space, depending on it's size and the I/O load.
The virtio-blk driver interprets -EIO form virtqueue_add() as an IO
error, despite the fact that swiotlb full is in absence of bugs a
recoverable condition.
Let us change the return code to -ENOMEM, and make the block layer
recover form these failures when virtio-blk encounters the condition
described above.
Cc: stable@vger.kernel.org
Fixes: 780bc7903a ("virtio_ring: Support DMA APIs")
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Michael Mueller <mimu@linux.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d791cfcbf9 ]
When we hot unplug a virtserialport and then try to hot plug again,
it fails:
(qemu) chardev-add socket,id=serial0,path=/tmp/serial0,server,nowait
(qemu) device_add virtserialport,bus=virtio-serial0.0,nr=2,\
chardev=serial0,id=serial0,name=serial0
(qemu) device_del serial0
(qemu) device_add virtserialport,bus=virtio-serial0.0,nr=2,\
chardev=serial0,id=serial0,name=serial0
kernel error:
virtio-ports vport2p2: Error allocating inbufs
qemu error:
virtio-serial-bus: Guest failure in adding port 2 for device \
virtio-serial0.0
This happens because buffers for the in_vq are allocated when the port is
added but are not released when the port is unplugged.
They are only released when virtconsole is removed (see a7a69ec0d8)
To avoid the problem and to be symmetric, we could allocate all the buffers
in init_vqs() as they are released in remove_vqs(), but it sounds like
a waste of memory.
Rather than that, this patch changes add_port() logic to ignore ENOSPC
error in fill_queue(), which means queue has already been filled.
Fixes: a7a69ec0d8 ("virtio_console: free buffers after reset")
Cc: mst@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2855b33514 ]
an allocated buffer doesn't need to be tied to a vq -
only vq->vdev is ever used. Pass the function the
just what it needs - the vdev.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c60300d68 ]
When out of memory and we can't add ctrl vq buffers,
probe fails. Unfortunately the error handling is
out of spec: it calls del_vqs without bothering
to reset the device first.
To fix, call the full cleanup function in this case.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e6e8df0726 upstream.
Add NULL checks to show() and store() in cpufreq.c to avoid attempts
to invoke a NULL callback.
Though some interfaces of cpufreq are set as read-only, users can
still get write permission using chmod which can lead to a kernel
crash, as follows:
chmod +w /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
echo 1 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
This bug was found in linux 4.19.
Signed-off-by: Kai Shen <shenkai8@huawei.com>
Reported-by: Feilong Lin <linfeilong@huawei.com>
Reviewed-by: Feilong Lin <linfeilong@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e08117c9d upstream.
Visual inspection of the usbvision driver shows that it suffers from
three races between its open, close, and disconnect handlers. In
particular, the driver is careful to update its usbvision->user and
usbvision->remove_pending flags while holding the private mutex, but:
usbvision_v4l2_close() and usbvision_radio_close() don't hold
the mutex while they check the value of
usbvision->remove_pending;
usbvision_disconnect() doesn't hold the mutex while checking
the value of usbvision->user; and
also, usbvision_v4l2_open() and usbvision_radio_open() don't
check whether the device has been unplugged before allowing
the user to open the device files.
Each of these can potentially lead to usbvision_release() being called
twice and use-after-free errors.
This patch fixes the races by reading the flags while the mutex is
still held and checking for pending removes before allowing an open to
succeed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dcd5d7a7a upstream.
There is the same incorrect approach to locking implemented in
vivid_stop_generating_vid_cap(), vivid_stop_generating_vid_out() and
sdr_cap_stop_streaming().
These functions are called during streaming stopping with vivid_dev.mutex
locked. And they all do the same mistake while stopping their kthreads,
which need to lock this mutex as well. See the example from
vivid_stop_generating_vid_cap():
/* shutdown control thread */
vivid_grab_controls(dev, false);
mutex_unlock(&dev->mutex);
kthread_stop(dev->kthread_vid_cap);
dev->kthread_vid_cap = NULL;
mutex_lock(&dev->mutex);
But when this mutex is unlocked, another vb2_fop_read() can lock it
instead of vivid_thread_vid_cap() and manipulate the buffer queue.
That causes a use-after-free access later.
To fix those issues let's:
1. avoid unlocking the mutex in vivid_stop_generating_vid_cap(),
vivid_stop_generating_vid_out() and sdr_cap_stop_streaming();
2. use mutex_trylock() with schedule_timeout_uninterruptible() in
the loops of the vivid kthread handlers.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4add02d22 upstream.
When vbi stream is started, followed by video streaming,
the vid_cap_streaming and vid_out_streaming were not being set to true,
which would cause the video stream to stop when vbi stream is stopped.
This patch allows to set vid_cap_streaming and vid_out_streaming to true.
According to Hans Verkuil it appears that these 'if (dev->kthread_vid_cap)'
checks are a left-over from the original vivid development and should never
have been there.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
