commit e225128c3f8be879e7d4eb71a25949e188b420ae upstream.
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
Cc: stable@vger.kernel.org
Fixes: cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts when enabling")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20250312-pinctrl-msm-type-latch-v1-1-ce87c561d3d7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aecb63e88c5e5fb9afb782a1577264c76f179af9 upstream.
Ensure the PHY reset and perst is asserted during power-off to
guarantee it is in a reset state upon repeated power-on calls. This
resolves an issue where the PHY may not properly initialize during
subsequent power-on cycles. Power-on will deassert the reset at the
appropriate time after tuning the PHY parameters.
During suspend/resume cycles, we observed that the PHY PLL failed to
lock during resume when the CPU temperature increased from 65C to 75C.
The observed errors were:
phy phy-32f00000.pcie-phy.3: phy poweron failed --> -110
imx6q-pcie 33800000.pcie: waiting for PHY ready timeout!
imx6q-pcie 33800000.pcie: PM: dpm_run_callback(): genpd_resume_noirq+0x0/0x80 returns -110
imx6q-pcie 33800000.pcie: PM: failed to resume noirq: error -110
This resulted in a complete CPU freeze, which is resolved by ensuring
the PHY is in reset during power-on, thus preventing PHY PLL failures.
Cc: stable@vger.kernel.org
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250305144355.20364-3-eichest@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2df181e1aea4628a8fd257f866026625d0519627 upstream.
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 40ca1bf580 ("PCI: brcmstb: Add MSI support")
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250122222955.1752778-1-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 708124d9e6e7ac5ebf927830760679136b23fdf0 upstream.
of_irq_init() will leak interrupt controller device node refcounts
in two places as explained below:
1) Leak refcounts of both @desc->dev and @desc->interrupt_parent when
suffers @desc->irq_init_cb() failure.
2) Leak refcount of @desc->interrupt_parent when cleans up list
@intc_desc_list in the end.
Refcounts of both @desc->dev and @desc->interrupt_parent were got in
the first loop, but of_irq_init() does not put them before kfree(@desc)
in places mentioned above, so causes refcount leakages.
Fix by putting refcounts involved before kfree(@desc).
Fixes: 8363ccb917 ("of/irq: add missing of_node_put")
Fixes: c71a54b082 ("of/irq: introduce of_irq_init")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-7-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbf71f44aaf241d853759a71de7e7ebcdb89be3d upstream.
of_irq_count() invokes of_irq_parse_one() to count IRQs, and successful
invocation of the later will get device node @irq.np refcount, but the
former does not put the refcount before next iteration invocation, hence
causes device node refcount leakages.
Fix by putting @irq.np refcount before the next iteration invocation.
Fixes: 3da5278727 ("of/irq: Rework of_irq_count()")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-5-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff93e7213d6cc8d9a7b0bc64f70ed26094e168f3 upstream.
if the node @out_irq->np got by of_irq_parse_raw() is a combo node which
consists of both controller and nexus, namely, of_irq_parse_raw() returns
due to condition (@ipar == @newpar), then the node's refcount was increased
twice, hence causes refcount leakage.
Fix by putting @out_irq->np refcount before returning due to the condition.
Also add comments about refcount of node @out_irq->np got by the API.
Fixes: 0412841812 ("of/irq: Allow matching of an interrupt-map local to an interrupt controller")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-4-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cb58d6c7b558a69957fabe159bfb184196e1e8d upstream.
of_irq_parse_one(@int_gen_dev, i, ...) will leak refcount of @i_th_phandle
int_gen_dev {
...
interrupts-extended = ..., <&i_th_phandle ...>, ...;
...
};
Refcount of @i_th_phandle is increased by of_parse_phandle_with_args()
but is not decreased by API of_irq_parse_one() before return, so causes
refcount leakage.
Rework the refcounting to use __free() cleanup and simplify the code to
have a single call to of_irq_parse_raw().
Also add comments about refcount of node @out_irq->np got by the API.
Fixes: 79d9701559 ("of/irq: create interrupts-extended property")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-2-93e3a2659aa7@quicinc.com
[robh: Use __free() to do puts]
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd5625fc86922f36bedee5846fefd647b7e72751 upstream.
msi_db_mask is of type 'u64', still the standard 'int' arithmetic is
performed to compute its value.
While most of the ntb_hw drivers actually don't utilize the higher 32
bits of the doorbell mask now, this may be the case for Switchtec - see
switchtec_ntb_init_db().
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2b0569b3b7 ("NTB: Add MSI interrupt support to ntb_transport")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef01cac401f18647d62720cf773d7bb0541827da upstream.
Acquire a lock on kvm->srcu when userspace is getting MP state to handle a
rather extreme edge case where "accepting" APIC events, i.e. processing
pending INIT or SIPI, can trigger accesses to guest memory. If the vCPU
is in L2 with INIT *and* a TRIPLE_FAULT request pending, then getting MP
state will trigger a nested VM-Exit by way of ->check_nested_events(), and
emuating the nested VM-Exit can access guest memory.
The splat was originally hit by syzkaller on a Google-internal kernel, and
reproduced on an upstream kernel by hacking the triple_fault_event_test
selftest to stuff a pending INIT, store an MSR on VM-Exit (to generate a
memory access on VMX), and do vcpu_mp_state_get() to trigger the scenario.
=============================
WARNING: suspicious RCU usage
6.14.0-rc3-b112d356288b-vmx/pi_lockdep_false_pos-lock #3 Not tainted
-----------------------------
include/linux/kvm_host.h:1058 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by triple_fault_ev/1256:
#0: ffff88810df5a330 (&vcpu->mutex){+.+.}-{4:4}, at: kvm_vcpu_ioctl+0x8b/0x9a0 [kvm]
stack backtrace:
CPU: 11 UID: 1000 PID: 1256 Comm: triple_fault_ev Not tainted 6.14.0-rc3-b112d356288b-vmx #3
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
<TASK>
dump_stack_lvl+0x7f/0x90
lockdep_rcu_suspicious+0x144/0x190
kvm_vcpu_gfn_to_memslot+0x156/0x180 [kvm]
kvm_vcpu_read_guest+0x3e/0x90 [kvm]
read_and_check_msr_entry+0x2e/0x180 [kvm_intel]
__nested_vmx_vmexit+0x550/0xde0 [kvm_intel]
kvm_check_nested_events+0x1b/0x30 [kvm]
kvm_apic_accept_events+0x33/0x100 [kvm]
kvm_arch_vcpu_ioctl_get_mpstate+0x30/0x1d0 [kvm]
kvm_vcpu_ioctl+0x33e/0x9a0 [kvm]
__x64_sys_ioctl+0x8b/0xb0
do_syscall_64+0x6c/0x170
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250401150504.829812-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc52ae0a708cb6fa3926d11c88e3c55e1171b4a1 upstream.
Explicitly zero/empty-initialize the unions used for PMU related CPUID
entries, instead of manually zeroing all fields (hopefully), or in the
case of 0x80000022, relying on the compiler to clobber the uninitialized
bitfields.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-ID: <20250315024102.2361628-1-seanjc@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42ea22e754ba4f2b86f8760ca27f6f71da2d982c upstream.
When the kernel contains a large number of functions that can be traced,
the loop in ftrace_graph_set_hash() may take a lot of time to execute.
This may trigger the softlockup watchdog.
Add cond_resched() within the loop to allow the kernel to remain
responsive even when processing a large number of functions.
This matches the cond_resched() that is used in other locations of the
code that iterates over all functions that can be traced.
Cc: stable@vger.kernel.org
Fixes: b9b0c831be ("ftrace: Convert graph filter to use hash tables")
Link: https://lore.kernel.org/tencent_3E06CE338692017B5809534B9C5C03DA7705@qq.com
Signed-off-by: zhoumin <teczm@foxmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2de510fccbca3d1906b55f4be5f1de83fa2424ef upstream.
There's a possible race condition in dm-verity - the prefetch work item
may race with suspend and it is possible that prefetch continues to run
while the device is suspended. Fix this by calling flush_workqueue and
dm_bufio_client_reset in the postsuspend hook.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00204ae3d6712ee053353920e3ce2b00c35ef75b upstream.
The dm-integrity target didn't set the error string when memory
allocation failed. This patch fixes it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c565428788fb9b49066f94ab7b10efc686a0a4c upstream.
There's a possible race condition in dm-ebs - dm bufio prefetch may be in
progress while the device is suspended. Fix this by calling
dm_bufio_client_reset in the postsuspend hook.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07bb097b92b987db518e72525b515d77904e966e upstream.
Currently, the ASP primary device check does not have support for PCI
domains, and, as a result, when the system is configured with PCI domains
(PCI segments) the wrong device can be selected as primary. This results
in commands submitted to the device timing out and failing. The device
check also relies on specific device and function assignments that may
not hold in the future.
Fix the primary ASP device check to include support for PCI domains and
to perform proper checking of the Bus/Device/Function positions.
Fixes: 2a6170dfe7 ("crypto: ccp: Add Platform Security Processor (PSP) device support")
Cc: stable@vger.kernel.org
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5eac348182d2b5ed1066459abedb7bc6b5466f81 upstream.
BRANCH_HALT_ENABLE and BRANCH_HALT_ENABLE_VOTED flags are used to check
halt status of branch clocks, which have an inverted logic for the halt
bit in CBCR register. However, the current logic in the _check_halt()
method only compares the BRANCH_HALT_ENABLE flags, ignoring the votable
branch clocks.
Update the logic to correctly handle the invert logic for votable clocks
using the BRANCH_HALT_ENABLE_VOTED flags.
Fixes: 9092d1083a ("clk: qcom: branch: Extend the invert logic for branch2 clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Ajit Pandey <quic_ajipan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250128-push_fix-v1-1-fafec6747881@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f8a394aa952257575910d57cf0a63627fa949a2 upstream.
Fix regression in mounts to e.g. onedrive shares.
Generally, reparse points are processed by the SMB server during the
SMB OPEN request, but there are few reparse points which do not have
OPEN-like meaning for the SMB server and has to be processed by the SMB
client. Those are symlinks and special files (fifo, socket, block, char).
For Linux SMB client, it is required to process also name surrogate reparse
points as they represent another entity on the SMB server system. Linux
client will mark them as separate mount points. Examples of name surrogate
reparse points are NTFS junction points (e.g. created by the "mklink" tool
on Windows servers).
So after processing the name surrogate reparse points, clear the
-EOPNOTSUPP error code returned from the parse_reparse_point() to let SMB
server to process reparse points.
And remove printing misleading error message "unhandled reparse tag:" as
reparse points are handled by SMB server and hence unhandled fact is normal
operation.
Fixes: cad3fc0a4c8c ("cifs: Throw -EOPNOTSUPP error on unsupported reparse point type from parse_reparse_point()")
Fixes: b587fd128660 ("cifs: Treat unhandled directory name surrogate reparse points as mount directory nodes")
Cc: stable@vger.kernel.org
Reported-by: Junwen Sun <sunjw8888@gmail.com>
Tested-by: Junwen Sun <sunjw8888@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2510859475d7f46ed7940db0853f3342bf1b65ee upstream.
The echo_interval is not limited in any way during mounting,
which makes it possible to write a large number to it. This can
cause an overflow when multiplying ctx->echo_interval by HZ in
match_server().
Add constraints for echo_interval to smb3_fs_context_parse_param().
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: adfeb3e00e ("cifs: Make echo interval tunable")
Cc: stable@vger.kernel.org
Signed-off-by: Roman Smirnov <r.smirnov@omp.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4885bd5935bb26f0a414ad55679a372e53f9b9b upstream.
cifs_server_dbg() implies server to be non-NULL so
move call under condition to avoid NULL pointer dereference.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e79b0332ae ("cifs: ignore cached share root handle closing errors")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee022e5cae052e0c67ca7c5fec0f2e7bc897c70e upstream.
The mapping table for the rk3328 is missing the entry for -25C which is
found in the TRM section 9.5.2 "Temperature-to-code mapping".
NOTE: the kernel uses the tsadc_q_sel=1'b1 mode which is defined as:
4096-<code in table>. Whereas the table in the TRM gives the code
"3774" for -25C, the kernel uses 4096-3774=322.
[Dragan Simic] : "After going through the RK3308 and RK3328 TRMs, as
well as through the downstream kernel code, it seems we may have
some troubles at our hands. Let me explain, please.
To sum it up, part 1 of the RK3308 TRM v1.1 says on page 538 that
the equation for the output when tsadc_q_sel equals 1 is (4096 -
tsadc_q), while part 1 of the RK3328 TRM v1.2 says that the output
equation is (1024 - tsadc_q) in that case.
The downstream kernel code, however, treats the RK3308 and RK3328
tables and their values as being the same. It even mentions 1024 as
the "offset" value in a comment block for the rk_tsadcv3_control()
function, just like the upstream code does, which is obviously wrong
"offset" value when correlated with the table on page 544 of part 1
of the RK3308 TRM v1.1.
With all this in mind, it's obvious that more work is needed to make
it clear where's the actual mistake (it could be that the TRM is
wrong), which I'll volunteer for as part of the SoC binning project.
In the meantime, this patch looks fine as-is to me, by offering
what's a clear improvement to the current state of the upstream
code"
Link: https://opensource.rock-chips.com/images/9/97/Rockchip_RK3328TRM_V1.1-Part1-20170321.pdf
Cc: stable@vger.kernel.org
Fixes: eda519d5f7 ("thermal: rockchip: Support the RK3328 SOC in thermal driver")
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250207175048.35959-1-twoerner@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1a453a57bc76be678bd746f84e3d73f378a9511 upstream.
The following causes a vsnprintf fault:
# echo 's:wake_lat char[] wakee; u64 delta;' >> /sys/kernel/tracing/dynamic_events
# echo 'hist:keys=pid:ts=common_timestamp.usecs if !(common_flags & 0x18)' > /sys/kernel/tracing/events/sched/sched_waking/trigger
# echo 'hist:keys=next_pid:delta=common_timestamp.usecs-$ts:onmatch(sched.sched_waking).trace(wake_lat,next_comm,$delta)' > /sys/kernel/tracing/events/sched/sched_switch/trigger
Because the synthetic event's "wakee" field is created as a dynamic string
(even though the string copied is not). The print format to print the
dynamic string changed from "%*s" to "%s" because another location
(__set_synth_event_print_fmt()) exported this to user space, and user
space did not need that. But it is still used in print_synth_event(), and
the output looks like:
<idle>-0 [001] d..5. 193.428167: wake_lat: wakee=(efault)sshd-sessiondelta=155
sshd-session-879 [001] d..5. 193.811080: wake_lat: wakee=(efault)kworker/u34:5delta=58
<idle>-0 [002] d..5. 193.811198: wake_lat: wakee=(efault)bashdelta=91
bash-880 [002] d..5. 193.811371: wake_lat: wakee=(efault)kworker/u35:2delta=21
<idle>-0 [001] d..5. 193.811516: wake_lat: wakee=(efault)sshd-sessiondelta=129
sshd-session-879 [001] d..5. 193.967576: wake_lat: wakee=(efault)kworker/u34:5delta=50
The length isn't needed as the string is always nul terminated. Just print
the string and not add the length (which was hard coded to the max string
length anyway).
Cc: stable@vger.kernel.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: Douglas Raillard <douglas.raillard@arm.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/20250407154139.69955768@gandalf.local.home
Fixes: 4d38328eb442d ("tracing: Fix synth event printk format for str fields");
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87af633689ce16ddb166c80f32b120e50b1295de upstream.
PVH dom0 re-uses logic from PV dom0, in which RAM ranges not assigned to
dom0 are re-used as scratch memory to map foreign and grant pages. Such
logic relies on reporting those unpopulated ranges as RAM to Linux, and
mark them as reserved. This way Linux creates the underlying page
structures required for metadata management.
Such approach works fine on PV because the initial balloon target is
calculated using specific Xen data, that doesn't take into account the
memory type changes described above. However on HVM and PVH the initial
balloon target is calculated using get_num_physpages(), and that function
does take into account the unpopulated RAM regions used as scratch space
for remote domain mappings.
This leads to PVH dom0 having an incorrect initial balloon target, which
causes malfunction (excessive memory freeing) of the balloon driver if the
dom0 memory target is later adjusted from the toolstack.
Fix this by using xen_released_pages to account for any pages that are part
of the memory map, but are already unpopulated when the balloon driver is
initialized. This accounts for any regions used for scratch remote
mappings. Note on x86 xen_released_pages definition is moved to
enlighten.c so it's uniformly available for all Xen-enabled builds.
Take the opportunity to unify PV with PVH/HVM guests regarding the usage of
get_num_physpages(), as that avoids having to add different logic for PV vs
PVH in both balloon_add_regions() and arch_xen_unpopulated_init().
Much like a6aa4eb994ee, the code in this changeset should have been part of
38620fc4e893.
Fixes: a6aa4eb994ee ('xen/x86: add extra pages to unpopulated-alloc if available')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20250407082838.65495-1-roger.pau@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1a69a940de58b16e8249dff26f74c8cc59b32be upstream.
sctp_sendmsg() re-uses associations and transports when possible by
doing a lookup based on the socket endpoint and the message destination
address, and then sctp_sendmsg_to_asoc() sets the selected transport in
all the message chunks to be sent.
There's a possible race condition if another thread triggers the removal
of that selected transport, for instance, by explicitly unbinding an
address with setsockopt(SCTP_SOCKOPT_BINDX_REM), after the chunks have
been set up and before the message is sent. This can happen if the send
buffer is full, during the period when the sender thread temporarily
releases the socket lock in sctp_wait_for_sndbuf().
This causes the access to the transport data in
sctp_outq_select_transport(), when the association outqueue is flushed,
to result in a use-after-free read.
This change avoids this scenario by having sctp_transport_free() signal
the freeing of the transport, tagging it as "dead". In order to do this,
the patch restores the "dead" bit in struct sctp_transport, which was
removed in
commit 47faa1e4c5 ("sctp: remove the dead field of sctp_transport").
Then, in the scenario where the sender thread has released the socket
lock in sctp_wait_for_sndbuf(), the bit is checked again after
re-acquiring the socket lock to detect the deletion. This is done while
holding a reference to the transport to prevent it from being freed in
the process.
If the transport was deleted while the socket lock was relinquished,
sctp_sendmsg_to_asoc() will return -EAGAIN to let userspace retry the
send.
The bug was found by a private syzbot instance (see the error report [1]
and the C reproducer that triggers it [2]).
Link: https://people.igalia.com/rcn/kernel_logs/20250402__KASAN_slab-use-after-free_Read_in_sctp_outq_select_transport.txt [1]
Link: https://people.igalia.com/rcn/kernel_logs/20250402__KASAN_slab-use-after-free_Read_in_sctp_outq_select_transport__repro.c [2]
Cc: stable@vger.kernel.org
Fixes: df132eff46 ("sctp: clear the transport of some out_chunk_list chunks in sctp_assoc_rm_peer")
Suggested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Ricardo Cañuelo Navarro <rcn@igalia.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20250404-kasan_slab-use-after-free_read_in_sctp_outq_select_transport__20250404-v1-1-5ce4a0b78ef2@igalia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaf99ac2ceb7c974f758a635723eeaf48596388e upstream.
When an uncorrected memory error is consumed there is a race between the
CMCI from the memory controller reporting an uncorrected error with a UCNA
signature, and the core reporting and SRAR signature machine check when
the data is about to be consumed.
- Background: why *UN*corrected errors tied to *C*MCI in Intel platform [1]
Prior to Icelake memory controllers reported patrol scrub events that
detected a previously unseen uncorrected error in memory by signaling a
broadcast machine check with an SRAO (Software Recoverable Action
Optional) signature in the machine check bank. This was overkill because
it's not an urgent problem that no core is on the verge of consuming that
bad data. It's also found that multi SRAO UCE may cause nested MCE
interrupts and finally become an IERR.
Hence, Intel downgrades the machine check bank signature of patrol scrub
from SRAO to UCNA (Uncorrected, No Action required), and signal changed to
#CMCI. Just to add to the confusion, Linux does take an action (in
uc_decode_notifier()) to try to offline the page despite the UC*NA*
signature name.
- Background: why #CMCI and #MCE race when poison is consuming in Intel platform [1]
Having decided that CMCI/UCNA is the best action for patrol scrub errors,
the memory controller uses it for reads too. But the memory controller is
executing asynchronously from the core, and can't tell the difference
between a "real" read and a speculative read. So it will do CMCI/UCNA if
an error is found in any read.
Thus:
1) Core is clever and thinks address A is needed soon, issues a speculative read.
2) Core finds it is going to use address A soon after sending the read request
3) The CMCI from the memory controller is in a race with MCE from the core
that will soon try to retire the load from address A.
Quite often (because speculation has got better) the CMCI from the memory
controller is delivered before the core is committed to the instruction
reading address A, so the interrupt is taken, and Linux offlines the page
(marking it as poison).
- Why user process is killed for instr case
Commit 046545a661 ("mm/hwpoison: fix error page recovered but reported
"not recovered"") tries to fix noise message "Memory error not recovered"
and skips duplicate SIGBUSs due to the race. But it also introduced a bug
that kill_accessing_process() return -EHWPOISON for instr case, as result,
kill_me_maybe() send a SIGBUS to user process.
If the CMCI wins that race, the page is marked poisoned when
uc_decode_notifier() calls memory_failure(). For dirty pages,
memory_failure() invokes try_to_unmap() with the TTU_HWPOISON flag,
converting the PTE to a hwpoison entry. As a result,
kill_accessing_process():
- call walk_page_range() and return 1 regardless of whether
try_to_unmap() succeeds or fails,
- call kill_proc() to make sure a SIGBUS is sent
- return -EHWPOISON to indicate that SIGBUS is already sent to the
process and kill_me_maybe() doesn't have to send it again.
However, for clean pages, the TTU_HWPOISON flag is cleared, leaving the
PTE unchanged and not converted to a hwpoison entry. Conversely, for
clean pages where PTE entries are not marked as hwpoison,
kill_accessing_process() returns -EFAULT, causing kill_me_maybe() to send
a SIGBUS.
Console log looks like this:
Memory failure: 0x827ca68: corrupted page was clean: dropped without side effects
Memory failure: 0x827ca68: recovery action for clean LRU page: Recovered
Memory failure: 0x827ca68: already hardware poisoned
mce: Memory error not recovered
To fix it, return 0 for "corrupted page was clean", preventing an
unnecessary SIGBUS to user process.
[1] https://lore.kernel.org/lkml/20250217063335.22257-1-xueshuai@linux.alibaba.com/T/#mba94f1305b3009dd340ce4114d3221fe810d1871
Link: https://lkml.kernel.org/r/20250312112852.82415-3-xueshuai@linux.alibaba.com
Fixes: 046545a661 ("mm/hwpoison: fix error page recovered but reported "not recovered"")
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jane Chu <jane.chu@oracle.com>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ruidong Tian <tianruidong@linux.alibaba.com>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4cdc2c4e248f48de23bc778870fd71e772a274 upstream.
This patch should fix a possible userfaultfd release() hang during
concurrent GUP.
This problem was initially reported by Dimitris Siakavaras in July 2023
[1] in a firecracker use case. Firecracker has a separate process
handling page faults remotely, and when the process releases the
userfaultfd it can race with a concurrent GUP from KVM trying to fault in
a guest page during the secondary MMU page fault process.
A similar problem was reported recently again by Jinjiang Tu in March 2025
[2], even though the race happened this time with a mlockall() operation,
which does GUP in a similar fashion.
In 2017, commit 656710a60e ("userfaultfd: non-cooperative: closing the
uffd without triggering SIGBUS") was trying to fix this issue. AFAIU,
that fixes well the fault paths but may not work yet for GUP. In GUP, the
issue is NOPAGE will be almost treated the same as "page fault resolved"
in faultin_page(), then the GUP will follow page again, seeing page
missing, and it'll keep going into a live lock situation as reported.
This change makes core mm return RETRY instead of NOPAGE for both the GUP
and fault paths, proactively releasing the mmap read lock. This should
guarantee the other release thread make progress on taking the write lock
and avoid the live lock even for GUP.
When at it, rearrange the comments to make sure it's uptodate.
[1] https://lore.kernel.org/r/79375b71-db2e-3e66-346b-254c90d915e2@cslab.ece.ntua.gr
[2] https://lore.kernel.org/r/20250307072133.3522652-1-tujinjiang@huawei.com
Link: https://lkml.kernel.org/r/20250312145131.1143062-1-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Jinjiang Tu <tujinjiang@huawei.com>
Cc: Dimitris Siakavaras <jimsiak@cslab.ece.ntua.gr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0ebbb3841e07c4493e6fe351698806b09a87a37 upstream.
The PGDAT_RECLAIM_LOCKED bit is used to provide mutual exclusion of node
reclaim for struct pglist_data using a single bit.
It is "locked" with a test_and_set_bit (similarly to a try lock) which
provides full ordering with respect to loads and stores done within
__node_reclaim().
It is "unlocked" with clear_bit(), which does not provide any ordering
with respect to loads and stores done before clearing the bit.
The lack of clear_bit() memory ordering with respect to stores within
__node_reclaim() can cause a subsequent CPU to fail to observe stores from
a prior node reclaim. This is not an issue in practice on TSO (e.g.
x86), but it is an issue on weakly-ordered architectures (e.g. arm64).
Fix this by using clear_bit_unlock rather than clear_bit to clear
PGDAT_RECLAIM_LOCKED with a release memory ordering semantic.
This provides stronger memory ordering (release rather than relaxed).
Link: https://lkml.kernel.org/r/20250312141014.129725-1-mathieu.desnoyers@efficios.com
Fixes: d773ed6b85 ("mm: test and set zone reclaim lock before starting reclaim")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jade Alglave <j.alglave@ucl.ac.uk>
Cc: Luc Maranget <luc.maranget@inria.fr>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 937582ee8e8d227c30ec147629a0179131feaa80 upstream.
Patch series "refactor mremap and fix bug", v3.
The existing mremap() logic has grown organically over a very long period
of time, resulting in code that is in many parts, very difficult to follow
and full of subtleties and sources of confusion.
In addition, it is difficult to thread state through the operation
correctly, as function arguments have expanded, some parameters are
expected to be temporarily altered during the operation, others are
intended to remain static and some can be overridden.
This series completely refactors the mremap implementation, sensibly
separating functions, adding comments to explain the more subtle aspects
of the implementation and making use of small structs to thread state
through everything.
The reason for doing so is to lay the groundwork for planned future
changes to the mremap logic, changes which require the ability to easily
pass around state.
Additionally, it would be unhelpful to add yet more logic to code that is
already difficult to follow without first refactoring it like this.
The first patch in this series additionally fixes a bug when a VMA with
start address zero is partially remapped.
Tested on real hardware under heavy workload and all self tests are
passing.
This patch (of 3):
Consider the case of a partial mremap() (that results in a VMA split) of
an accountable VMA (i.e. which has the VM_ACCOUNT flag set) whose start
address is zero, with the MREMAP_MAYMOVE flag specified and a scenario
where a move does in fact occur:
addr end
| |
v v
|-------------|
| vma |
|-------------|
0
This move is affected by unmapping the range [addr, end). In order to
prevent an incorrect decrement of accounted memory which has already been
determined, the mremap() code in move_vma() clears VM_ACCOUNT from the VMA
prior to doing so, before reestablishing it in each of the VMAs
post-split:
addr end
| |
v v
|---| |---|
| A | | B |
|---| |---|
Commit 6b73cff239 ("mm: change munmap splitting order and move_vma()")
changed this logic such as to determine whether there is a need to do so
by establishing account_start and account_end and, in the instance where
such an operation is required, assigning them to vma->vm_start and
vma->vm_end.
Later the code checks if the operation is required for 'A' referenced
above thusly:
if (account_start) {
...
}
However, if the VMA described above has vma->vm_start == 0, which is now
assigned to account_start, this branch will not be executed.
As a result, the VMA 'A' above will remain stripped of its VM_ACCOUNT
flag, incorrectly.
The fix is to simply convert these variables to booleans and set them as
required.
Link: https://lkml.kernel.org/r/cover.1741639347.git.lorenzo.stoakes@oracle.com
Link: https://lkml.kernel.org/r/dc55cb6db25d97c3d9e460de4986a323fa959676.1741639347.git.lorenzo.stoakes@oracle.com
Fixes: 6b73cff239 ("mm: change munmap splitting order and move_vma()")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 691ee97e1a9de0cdb3efb893c1f180e3f4a35e32 upstream.
Patch series "Fix lazy mmu mode", v2.
I'm planning to implement lazy mmu mode for arm64 to optimize vmalloc. As
part of that, I will extend lazy mmu mode to cover kernel mappings in
vmalloc table walkers. While lazy mmu mode is already used for kernel
mappings in a few places, this will extend it's use significantly.
Having reviewed the existing lazy mmu implementations in powerpc, sparc
and x86, it looks like there are a bunch of bugs, some of which may be
more likely to trigger once I extend the use of lazy mmu. So this series
attempts to clarify the requirements and fix all the bugs in advance of
that series. See patch #1 commit log for all the details.
This patch (of 5):
The docs, implementations and use of arch_[enter|leave]_lazy_mmu_mode() is
a bit of a mess (to put it politely). There are a number of issues
related to nesting of lazy mmu regions and confusion over whether the
task, when in a lazy mmu region, is preemptible or not. Fix all the
issues relating to the core-mm. Follow up commits will fix the
arch-specific implementations. 3 arches implement lazy mmu; powerpc,
sparc and x86.
When arch_[enter|leave]_lazy_mmu_mode() was first introduced by commit
6606c3e0da ("[PATCH] paravirt: lazy mmu mode hooks.patch"), it was
expected that lazy mmu regions would never nest and that the appropriate
page table lock(s) would be held while in the region, thus ensuring the
region is non-preemptible. Additionally lazy mmu regions were only used
during manipulation of user mappings.
Commit 38e0edb15b ("mm/apply_to_range: call pte function with lazy
updates") started invoking the lazy mmu mode in apply_to_pte_range(),
which is used for both user and kernel mappings. For kernel mappings the
region is no longer protected by any lock so there is no longer any
guarantee about non-preemptibility. Additionally, for RT configs, the
holding the PTL only implies no CPU migration, it doesn't prevent
preemption.
Commit bcc6cc8325 ("mm: add default definition of set_ptes()") added
arch_[enter|leave]_lazy_mmu_mode() to the default implementation of
set_ptes(), used by x86. So after this commit, lazy mmu regions can be
nested. Additionally commit 1a10a44dfc ("sparc64: implement the new
page table range API") and commit 9fee28baa6 ("powerpc: implement the
new page table range API") did the same for the sparc and powerpc
set_ptes() overrides.
powerpc couldn't deal with preemption so avoids it in commit b9ef323ea1
("powerpc/64s: Disable preemption in hash lazy mmu mode"), which
explicitly disables preemption for the whole region in its implementation.
x86 can support preemption (or at least it could until it tried to add
support nesting; more on this below). Sparc looks to be totally broken in
the face of preemption, as far as I can tell.
powerpc can't deal with nesting, so avoids it in commit 47b8def935
("powerpc/mm: Avoid calling arch_enter/leave_lazy_mmu() in set_ptes"),
which removes the lazy mmu calls from its implementation of set_ptes().
x86 attempted to support nesting in commit 49147beb0c ("x86/xen: allow
nesting of same lazy mode") but as far as I can tell, this breaks its
support for preemption.
In short, it's all a mess; the semantics for
arch_[enter|leave]_lazy_mmu_mode() are not clearly defined and as a result
the implementations all have different expectations, sticking plasters and
bugs.
arm64 is aiming to start using these hooks, so let's clean everything up
before adding an arm64 implementation. Update the documentation to state
that lazy mmu regions can never be nested, must not be called in interrupt
context and preemption may or may not be enabled for the duration of the
region. And fix the generic implementation of set_ptes() to avoid
nesting.
arch-specific fixes to conform to the new spec will proceed this one.
These issues were spotted by code review and I have no evidence of issues
being reported in the wild.
Link: https://lkml.kernel.org/r/20250303141542.3371656-1-ryan.roberts@arm.com
Link: https://lkml.kernel.org/r/20250303141542.3371656-2-ryan.roberts@arm.com
Fixes: bcc6cc8325 ("mm: add default definition of set_ptes()")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Juegren Gross <jgross@suse.com>
Cc: Matthew Wilcow (Oracle) <willy@infradead.org>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 442b1eca223b4860cc85ef970ae602d125aec5a4 upstream.
When a process consumes a UE in a page, the memory failure handler
attempts to collect information for a potential SIGBUS. If the page is an
anonymous page, page_mapped_in_vma(page, vma) is invoked in order to
1. retrieve the vaddr from the process' address space,
2. verify that the vaddr is indeed mapped to the poisoned page,
where 'page' is the precise small page with UE.
It's been observed that when injecting poison to a non-head subpage of an
anonymous hugetlb page, no SIGBUS shows up, while injecting to the head
page produces a SIGBUS. The cause is that, though hugetlb_walk() returns
a valid pmd entry (on x86), but check_pte() detects mismatch between the
head page per the pmd and the input subpage. Thus the vaddr is considered
not mapped to the subpage and the process is not collected for SIGBUS
purpose. This is the calling stack:
collect_procs_anon
page_mapped_in_vma
page_vma_mapped_walk
hugetlb_walk
huge_pte_lock
check_pte
check_pte() header says that it
"check if [pvmw->pfn, @pvmw->pfn + @pvmw->nr_pages) is mapped at the @pvmw->pte"
but practically works only if pvmw->pfn is the head page pfn at pvmw->pte.
Hindsight acknowledging that some pvmw->pte could point to a hugepage of
some sort such that it makes sense to make check_pte() work for hugepage.
Link: https://lkml.kernel.org/r/20250224211445.2663312-1-jane.chu@oracle.com
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Kirill A. Shuemov <kirill.shutemov@linux.intel.com>
Cc: linmiaohe <linmiaohe@huawei.com>
Cc: Matthew Wilcow (Oracle) <willy@infradead.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1d416bf9faf4f4871cb5a943614a07f80a7d70f upstream.
Since commit 38e0edb15b ("mm/apply_to_range: call pte function with lazy
updates") it's been possible for arch_[enter|leave]_lazy_mmu_mode() to be
called without holding a page table lock (for the kernel mappings case),
and therefore it is possible that preemption may occur while in the lazy
mmu mode. The Sparc lazy mmu implementation is not robust to preemption
since it stores the lazy mode state in a per-cpu structure and does not
attempt to manage that state on task switch.
Powerpc had the same issue and fixed it by explicitly disabling preemption
in arch_enter_lazy_mmu_mode() and re-enabling in
arch_leave_lazy_mmu_mode(). See commit b9ef323ea1 ("powerpc/64s:
Disable preemption in hash lazy mmu mode").
Given Sparc's lazy mmu mode is based on powerpc's, let's fix it in the
same way here.
Link: https://lkml.kernel.org/r/20250303141542.3371656-4-ryan.roberts@arm.com
Fixes: 38e0edb15b ("mm/apply_to_range: call pte function with lazy updates")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Juegren Gross <jgross@suse.com>
Cc: Matthew Wilcow (Oracle) <willy@infradead.org>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35fec1089ebb5617f85884d3fa6a699ce6337a75 upstream.
If do_zone_finish() is called with a filesystem that has missing devices
(e.g. a RAID file system mounted in degraded mode) it is accessing the
btrfs_device::zone_info pointer, which will not be set if the device
in question is missing.
Check if the device is present (by checking if it has a valid block device
pointer associated) and if not, skip zone finishing for it.
Fixes: 4dcbb8ab31 ("btrfs: zoned: make zone finishing multi stripe capable")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bbc4a45e5eb6b868357c1045bf6f38f6ba576e0 upstream.
If btrfs_zone_activate() is called with a filesystem that has missing
devices (e.g. a RAID file system mounted in degraded mode) it is accessing
the btrfs_device::zone_info pointer, which will not be set if the device in
question is missing.
Check if the device is present (by checking if it has a valid block
device pointer associated) and if not, skip zone activation for it.
Fixes: f9a912a3c4 ("btrfs: zoned: make zone activation multi stripe capable")
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
