[ Upstream commit c4d57c22ac ]
On all newer bq27xxx ICs, the AveragePower register contains a signed
value; in addition to handling the raw value as unsigned, the driver
code also didn't convert it to µW as expected.
At least for the BQ28Z610, the reference manual incorrectly states that
the value is in units of 1mW and not 10mW. I have no way of knowing
whether the manuals of other supported ICs contain the same error, or if
there are models that actually use 1mW. At least, the new code shouldn't
be *less* correct than the old version for any device.
power_avg is removed from the cache structure, se we don't have to
extend it to store both a signed value and an error code. Always getting
an up-to-date value may be desirable anyways, as it avoids inconsistent
current and power readings when switching between charging and
discharging.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f6c45ac5f ]
In practice, IA_CSS_PIPE_ID_NUM should never be used when
calling atomisp_q_video_buffers_to_css(), as the driver should
discover the right pipe before calling it.
Yet, if some pipe parsing issue happens, it could end using
it.
So, add a WARN_ON() to prevent such case.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc271b6754 ]
The correct return code to report an invalid pipeline configuration is
-EPIPE. Return it instead of -EINVAL from __capture_legacy_try_fmt()
when the capture format doesn't match the media bus format of the
connected subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee6ddf5847 ]
Running an rcuscale stress-suite can lead to "Out of memory" of a
system. This can happen under high memory pressure with a small amount
of physical memory.
For example, a KVM test configuration with 64 CPUs and 512 megabytes
can result in OOM when running rcuscale with below parameters:
../kvm.sh --torture rcuscale --allcpus --duration 10 --kconfig CONFIG_NR_CPUS=64 \
--bootargs "rcuscale.kfree_rcu_test=1 rcuscale.kfree_nthreads=16 rcuscale.holdoff=20 \
rcuscale.kfree_loops=10000 torture.disable_onoff_at_boot" --trust-make
<snip>
[ 12.054448] kworker/1:1H invoked oom-killer: gfp_mask=0x2cc0(GFP_KERNEL|__GFP_NOWARN), order=0, oom_score_adj=0
[ 12.055303] CPU: 1 PID: 377 Comm: kworker/1:1H Not tainted 5.11.0-rc3+ #510
[ 12.055416] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-1 04/01/2014
[ 12.056485] Workqueue: events_highpri fill_page_cache_func
[ 12.056485] Call Trace:
[ 12.056485] dump_stack+0x57/0x6a
[ 12.056485] dump_header+0x4c/0x30a
[ 12.056485] ? del_timer_sync+0x20/0x30
[ 12.056485] out_of_memory.cold.47+0xa/0x7e
[ 12.056485] __alloc_pages_slowpath.constprop.123+0x82f/0xc00
[ 12.056485] __alloc_pages_nodemask+0x289/0x2c0
[ 12.056485] __get_free_pages+0x8/0x30
[ 12.056485] fill_page_cache_func+0x39/0xb0
[ 12.056485] process_one_work+0x1ed/0x3b0
[ 12.056485] ? process_one_work+0x3b0/0x3b0
[ 12.060485] worker_thread+0x28/0x3c0
[ 12.060485] ? process_one_work+0x3b0/0x3b0
[ 12.060485] kthread+0x138/0x160
[ 12.060485] ? kthread_park+0x80/0x80
[ 12.060485] ret_from_fork+0x22/0x30
[ 12.062156] Mem-Info:
[ 12.062350] active_anon:0 inactive_anon:0 isolated_anon:0
[ 12.062350] active_file:0 inactive_file:0 isolated_file:0
[ 12.062350] unevictable:0 dirty:0 writeback:0
[ 12.062350] slab_reclaimable:2797 slab_unreclaimable:80920
[ 12.062350] mapped:1 shmem:2 pagetables:8 bounce:0
[ 12.062350] free:10488 free_pcp:1227 free_cma:0
...
[ 12.101610] Out of memory and no killable processes...
[ 12.102042] Kernel panic - not syncing: System is deadlocked on memory
[ 12.102583] CPU: 1 PID: 377 Comm: kworker/1:1H Not tainted 5.11.0-rc3+ #510
[ 12.102600] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-1 04/01/2014
<snip>
Because kvfree_rcu() has a fallback path, memory allocation failure is
not the end of the world. Furthermore, the added overhead of aggressive
GFP settings must be balanced against the overhead of the fallback path,
which is a cache miss for double-argument kvfree_rcu() and a call to
synchronize_rcu() for single-argument kvfree_rcu(). The current choice
of GFP_KERNEL|__GFP_NOWARN can result in longer latencies than a call
to synchronize_rcu(), so less-tenacious GFP flags would be helpful.
Here is the tradeoff that must be balanced:
a) Minimize use of the fallback path,
b) Avoid pushing the system into OOM,
c) Bound allocation latency to that of synchronize_rcu(), and
d) Leave the emergency reserves to use cases lacking fallbacks.
This commit therefore changes GFP flags from GFP_KERNEL|__GFP_NOWARN to
GFP_KERNEL|__GFP_NORETRY|__GFP_NOMEMALLOC|__GFP_NOWARN. This combination
leaves the emergency reserves alone and can initiate reclaim, but will
not invoke the OOM killer.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b89997aa88 ]
Being called for each dequeue, util_est reduces the number of its updates
by filtering out when the EWMA signal is different from the task util_avg
by less than 1%. It is a problem for a sudden util_avg ramp-up. Due to the
decay from a previous high util_avg, EWMA might now be close enough to
the new util_avg. No update would then happen while it would leave
ue.enqueued with an out-of-date value.
Taking into consideration the two util_est members, EWMA and enqueued for
the filtering, ensures, for both, an up-to-date value.
This is for now an issue only for the trace probe that might return the
stale value. Functional-wise, it isn't a problem, as the value is always
accessed through max(enqueued, ewma).
This problem has been observed using LISA's UtilConvergence:test_means on
the sd845c board.
No regression observed with Hackbench on sd845c and Perf-bench sched pipe
on hikey/hikey960.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lkml.kernel.org/r/20210225165820.1377125-1-vincent.donnefort@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb0cd09be4 ]
When unloading driver after killing some applications, it will hit sdma
flush tlb job timeout which is called by ttm_bo_delay_delete. So
to avoid the job submit after fence driver fini, call ttm_bo_lock_delayed_workqueue
before fence driver fini. And also put drm_sched_fini before waiting fence.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89adc10178 ]
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:59:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: note: (near initialization for ‘aux_shift.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:181:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: note: (near initialization for ‘aux_mask.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6f91fc183 ]
amdgpu DM handles INTERRUPT_LOW_IRQ_CONTEXT interrupt(hpd, hpd_rx) by using work
queue and uses single work_struct. If new interrupt is recevied before the
previous handler finished, new interrupts(same type) will be discarded and
driver just sends "amdgpu_dm_irq_schedule_work FAILED" message out. If some
important hpd, hpd_rx related interrupts are missed by driver the hot (un)plug
devices may cause system hang or instability, such as issues with system
resume from S3 sleep with mst device connected.
This patch dynamically allocates new amdgpu_dm_irq_handler_data for new
interrupts if previous INTERRUPT_LOW_IRQ_CONTEXT interrupt work has not been
handled. So the new interrupt works can be queued to the same workqueue_struct,
instead of discard the new interrupts. All allocated amdgpu_dm_irq_handler_data
are put into a single linked list and will be reused after.
Signed-off-by: Xiaogang Chen <xiaogang.chen@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ad98e8aeb ]
[Why]
There is a window of time where we optimize bandwidth due to no streams
enabled will enable PSTATE changing but HUBPs are not disabled yet.
This results in underflow counter increasing in some hotplug scenarios.
[How]
Set the optimize-bandwidth flag for later processing once all the HUBPs
are properly disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 349a19b2f1 ]
[why]
This check for ASIC revision is no longer useful and causes
lightup issues after a topology change in MST DSC scenario.
In this case, DSC configs should be recalculated for the new
topology. This check prevented that from happening on certain
ASICs that do, in fact, support DSC.
[how]
Change the ASIC revision to instead check if DSC is supported.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a9213a935 ]
A few BUG_ON()'s in replace_path are purely to keep us from making
logical mistakes, so replace them with ASSERT()'s.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 592fbcd50c ]
We call btrfs_update_root in btrfs_update_reloc_root, which can fail for
all sorts of reasons, including IO errors. Instead of panicing the box
lets return the error, now that all callers properly handle those
errors.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84c50ba521 ]
We do memory allocations here, read blocks from disk, all sorts of
operations that could easily fail at any given point. Instead of
panicing the box, simply return the error back up the chain, all callers
at this point have proper error handling.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d347b4aaa1 ]
When initially probing the SPI slave device, the call for disabling an
SPI device without the SPI_CS_HIGH flag is not applied, as the
condition for checking whether or not the state to be applied equals the
one currently set evaluates to true.
This however might not necessarily be the case, as the chipselect might
be active.
Add a force flag to spi_set_cs which allows to override this
early exit condition. Set it to false everywhere except when called
from spi_setup to sync up the initial CS state.
Fixes commit d40f0b6f2e ("spi: Avoid setting the chip select if we don't
need to")
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210416195956.121811-1-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f34cc4a8d ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13343badae ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 747bf30fd9 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cb3ad7019 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc987ae915 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06cd7423cf ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Signed-off-by: Shixin Liu <liushixin2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1723d8b87 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092716.3270248-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a932ee40c2 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c782817a9 ]
In some cases when firmware is busy or updating, some mailbox commands
still timeout on some newer CPUs. To fix this issue, change how we
process timeout.
With this change, replaced timeout from using simple count with real
timeout in micro-seconds using ktime. When the command response takes
more than average processing time, yield to other tasks. The worst case
timeout is extended upto 1 milli-second.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210330220840.3113959-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e70b710f3 ]
The current string size to print cpulist can accommodate upto 80
logical CPUs per package. But this limit is not enough. So increase
the string size. Also prevent buffer overflow, if the string size
reaches limit.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 286fd02fd5 ]
The Max Interrupters supported by the controller is given in a 10bit
wide bitfield, but the driver uses a fixed 128 size array to index these
interrupters.
Klockwork reports a possible array out of bounds case which in theory
is possible. In practice this hasn't been hit as a common number of Max
Interrupters for new controllers is 8, not even close to 128.
This needs to be fixed anyway
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210406070208.3406266-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
