[ Upstream commit df24373435f5899a2a98b7d377479c8d4376613b ]
DPU debugging macros need to be converted to a proper drm_debug_*
macros, however this is a going an intrusive patch, not suitable for a
fix. Wire DPU_DEBUG and DPU_DEBUG_DRIVER to always use DRM_DEBUG_DRIVER
to make sure that DPU debugging messages always end up in the drm debug
messages and are controlled via the usual drm.debug mask.
I don't think that it is a good idea for a generic DPU_DEBUG macro to be
tied to DRM_UT_KMS. It is used to report a debug message from driver, so by
default it should go to the DRM_UT_DRIVER channel. While refactoring
debug macros later on we might end up with particular messages going to
ATOMIC or KMS, but DRIVER should be the default.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/606932/
Link: https://lore.kernel.org/r/20240802-dpu-fix-wb-v2-2-7eac9eb8e895@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 797a68c9de0f5a5447baf4bd3bb9c10a3993435b ]
If a multicast address is removed but there are still some multicast
addresses, that address would remain programmed into the frame filter.
Fix this by explicitly setting the enable bit for each filter.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-3-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ae738dfef2c0323752ab81786e2d298c9939321 ]
If promiscuous mode is disabled when there are fewer than four multicast
addresses, then it will not be reflected in the hardware. Fix this by
always clearing the promiscuous mode flag even when we program multicast
addresses.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-2-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af688a99eb1fc7ef69774665d61e6be51cea627a ]
Some CPT AF registers are per LF and others are global. Translation
of PF/VF local LF slot number to actual LF slot number is required
only for accessing perf LF registers. CPT AF global registers access
do not require any LF slot number. Also, there is no reason CPT
PF/VF to know actual lf's register offset.
Without this fix microcode loading will fail, VFs cannot be created
and hardware is not usable.
Fixes: bc35e28af789 ("octeontx2-af: replace cpt slot with lf id on reg write")
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821070558.1020101-1-bbhushan2@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ea14ccb60c8ab829349979b22b58a941ec4a3ee ]
Ensure there is sufficient room to access the protocol field of the
VLAN header, validate it once before the flowtable lookup.
=====================================================
BUG: KMSAN: uninit-value in nf_flow_offload_inet_hook+0x45a/0x5f0 net/netfilter/nf_flow_table_inet.c:32
nf_flow_offload_inet_hook+0x45a/0x5f0 net/netfilter/nf_flow_table_inet.c:32
nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline]
nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626
nf_hook_ingress include/linux/netfilter_netdev.h:34 [inline]
nf_ingress net/core/dev.c:5440 [inline]
Fixes: 4cd91f7c29 ("netfilter: flowtable: add vlan support")
Reported-by: syzbot+8407d9bb88cd4c6bf61a@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c07ff8592d57ed258afee5a5e04991a48dbaf382 ]
There is a bug in netem_enqueue() introduced by
commit 5845f70638 ("net: netem: fix skb length BUG_ON in __skb_to_sgvec")
that can lead to a use-after-free.
This commit made netem_enqueue() always return NET_XMIT_SUCCESS
when a packet is duplicated, which can cause the parent qdisc's q.qlen
to be mistakenly incremented. When this happens qlen_notify() may be
skipped on the parent during destruction, leaving a dangling pointer
for some classful qdiscs like DRR.
There are two ways for the bug happen:
- If the duplicated packet is dropped by rootq->enqueue() and then
the original packet is also dropped.
- If rootq->enqueue() sends the duplicated packet to a different qdisc
and the original packet is dropped.
In both cases NET_XMIT_SUCCESS is returned even though no packets
are enqueued at the netem qdisc.
The fix is to defer the enqueue of the duplicate packet until after
the original packet has been guaranteed to return NET_XMIT_SUCCESS.
Fixes: 5845f70638 ("net: netem: fix skb length BUG_ON in __skb_to_sgvec")
Reported-by: Budimir Markovic <markovicbudimir@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240819175753.5151-1-stephen@networkplumber.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c50e7475961c36ec4d21d60af055b32f9436b431 ]
The dpaa2_switch_add_bufs() function returns the number of bufs that it
was able to add. It returns BUFS_PER_CMD (7) for complete success or a
smaller number if there are not enough pages available. However, the
error checking is looking at the total number of bufs instead of the
number which were added on this iteration. Thus the error checking
only works correctly for the first iteration through the loop and
subsequent iterations are always counted as a success.
Fix this by checking only the bufs added in the current iteration.
Fixes: 0b1b713704 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/eec27f30-b43f-42b6-b8ee-04a6f83423b6@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50b2143356e888777fc5bca023c39f34f404613a ]
Architectures that have PAGE_SIZE >= 8192 such as arm64 should act the
same as x86 currently, meaning reuse of a page should only take place
when no one else is busy with it.
Do two things independently of underlying PAGE_SIZE:
- store the page count under ice_rx_buf::pgcnt
- then act upon its value vs ice_rx_buf::pagecnt_bias when making the
decision regarding page reuse
Fixes: 2b245cb294 ("ice: Implement transmit and NAPI support")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac07533911 ]
This will allow us to avoid carrying additional auxiliary array of page
counts when dealing with XDP multi buffer support. Previously combining
fragmented frame to skb was not affected in the same way as XDP would be
as whole frame is needed to be in place before executing XDP prog.
Therefore, when going through HW Rx descriptors one-by-one, calls to
ice_put_rx_buf() need to be taken *after* running XDP prog on a
potentially multi buffered frame, so some additional storage of
page count is needed.
By adding page count to rx buf, it will make it easier to walk through
processed entries at the end of rx cleaning routine and decide whether
or not buffers should be recycled.
While at it, bump ice_rx_buf::pagecnt_bias from u16 up to u32. It was
proven many times that calculations on variables smaller than standard
register size are harmful. This was also the case during experiments
with embedding page count to ice_rx_buf - when this was added as u16 it
had a performance impact.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-4-maciej.fijalkowski@intel.com
Stable-dep-of: 50b2143356e8 ("ice: fix page reuse when PAGE_SIZE is over 8k")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb0473e0e9 ]
In preparation for XDP multi-buffer support, let's store xdp_buff on
Rx ring struct. This will allow us to combine fragmented frames across
separate NAPI cycles in the same way as currently skb fragments are
handled. This means that skb pointer on Rx ring will become redundant
and will be removed. For now it is kept and layout of Rx ring struct was
not inspected, some member movement will be needed later on so that will
be the time to take care of it.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-3-maciej.fijalkowski@intel.com
Stable-dep-of: 50b2143356e8 ("ice: fix page reuse when PAGE_SIZE is over 8k")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c61bcebde7 ]
Rx path is going to be modified in a way that fragmented frame will be
gathered within xdp_buff in the first place. This approach implies that
underlying buffer has to provide tailroom for skb_shared_info. This is
currently the case when ring uses build_skb but not when legacy-rx knob
is turned on. This case configures 2k Rx buffers and has no way to
provide either headroom or tailroom - FWIW it currently has
XDP_PACKET_HEADROOM which is broken and in here it is removed. 2k Rx
buffers were used so driver in this setting was able to support 9k MTU
as it can chain up to 5 Rx buffers. With offset configuring HW writing
2k of a data was passing the half of the page which broke the assumption
of our internal page recycling tricks.
Now if above got fixed and legacy-rx path would be left as is, when
referring to skb_shared_info via xdp_get_shared_info_from_buff(),
packet's content would be corrupted again. Hence size of Rx buffer needs
to be lowered and therefore supported MTU. This operation will allow us
to keep the unified data path and with 8k MTU users (if any of
legacy-rx) would still be good to go. However, tendency is to drop the
support for this code path at some point.
Add ICE_RXBUF_1664 as vsi::rx_buf_len and ICE_MAX_FRAME_LEGACY_RX (8320)
as vsi::max_frame for legacy-rx. For bigger page sizes configure 3k Rx
buffers, not 2k.
Since headroom support is removed, disable data_meta support on legacy-rx.
When preparing XDP buff, rely on ice_rx_ring::rx_offset setting when
deciding whether to support data_meta or not.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/bpf/20230131204506.219292-2-maciej.fijalkowski@intel.com
Stable-dep-of: 50b2143356e8 ("ice: fix page reuse when PAGE_SIZE is over 8k")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4c5c5d2ef40a9f67a9241dc5422eac9ffe19547 ]
If the active slave is cleared manually the xfrm state is not flushed.
This leads to xfrm add/del imbalance and adding the same state multiple
times. For example when the device cannot handle anymore states we get:
[ 1169.884811] bond0: (slave eni0np1): bond_ipsec_add_sa_all: failed to add SA
because it's filled with the same state after multiple active slave
clearings. This change also has a few nice side effects: user-space
gets a notification for the change, the old device gets its mac address
and promisc/mcast adjusted properly.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95c90e4ad89d493a7a14fa200082e466e2548f9d ]
We must check if there is an active slave before dereferencing the pointer.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc59b9a5f7201b9f7272944596113a82cc7773d5 ]
Fix the return type which should be bool.
Fixes: 955b785ec6 ("bonding: fix suspicious RCU usage in bond_ipsec_offload_ok()")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b3e33fcc38f7750604b065c55a43e94c5bc3145 ]
GRO code checks for matching layer 2 headers to see, if packet belongs
to the same flow and because ip6 tunnel set dev->hard_header_len
this check fails in cases, where it shouldn't. To fix this don't
set hard_header_len, but use needed_headroom like ipv4/ip_tunnel.c
does.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Link: https://patch.msgid.link/20240815151419.109864-1-tbogendoerfer@suse.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0b39e2dc7017ac667b70bdeee5293e410fab2fb ]
nft_counter_reset() resets the counter by subtracting the previously
retrieved value from the counter. This is a write operation on the
counter and as such it requires to be performed with a write sequence of
nft_counter_seq to serialize against its possible reader.
Update the packets/ bytes within write-sequence of nft_counter_seq.
Fixes: d84701ecbc ("netfilter: nft_counter: rework atomic dump and reset")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eacdd71b3436b54d5fc8218c4bb0187d92a6892 ]
The sequence counter nft_counter_seq is a per-CPU counter. There is no
lock associated with it. nft_counter_do_eval() is using the same counter
and disables BH which suggest that it can be invoked from a softirq.
This in turn means that nft_counter_offload_stats(), which disables only
preemption, can be interrupted by nft_counter_do_eval() leading to two
writer for one seqcount_t.
This can lead to loosing stats or reading statistics while they are
updated.
Disable BH during stats update in nft_counter_offload_stats() to ensure
one writer at a time.
Fixes: b72920f6e4 ("netfilter: nftables: counter hardware offload support")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 565d121b69980637f040eb4d84289869cdaabedf ]
Its possible that two threads call tcp_sk_exit_batch() concurrently,
once from the cleanup_net workqueue, once from a task that failed to clone
a new netns. In the latter case, error unwinding calls the exit handlers
in reverse order for the 'failed' netns.
tcp_sk_exit_batch() calls tcp_twsk_purge().
Problem is that since commit b099ce2602 ("net: Batch inet_twsk_purge"),
this function picks up twsk in any dying netns, not just the one passed
in via exit_batch list.
This means that the error unwind of setup_net() can "steal" and destroy
timewait sockets belonging to the exiting netns.
This allows the netns exit worker to proceed to call
WARN_ON_ONCE(!refcount_dec_and_test(&net->ipv4.tcp_death_row.tw_refcount));
without the expected 1 -> 0 transition, which then splats.
At same time, error unwind path that is also running inet_twsk_purge()
will splat as well:
WARNING: .. at lib/refcount.c:31 refcount_warn_saturate+0x1ed/0x210
...
refcount_dec include/linux/refcount.h:351 [inline]
inet_twsk_kill+0x758/0x9c0 net/ipv4/inet_timewait_sock.c:70
inet_twsk_deschedule_put net/ipv4/inet_timewait_sock.c:221
inet_twsk_purge+0x725/0x890 net/ipv4/inet_timewait_sock.c:304
tcp_sk_exit_batch+0x1c/0x170 net/ipv4/tcp_ipv4.c:3522
ops_exit_list+0x128/0x180 net/core/net_namespace.c:178
setup_net+0x714/0xb40 net/core/net_namespace.c:375
copy_net_ns+0x2f0/0x670 net/core/net_namespace.c:508
create_new_namespaces+0x3ea/0xb10 kernel/nsproxy.c:110
... because refcount_dec() of tw_refcount unexpectedly dropped to 0.
This doesn't seem like an actual bug (no tw sockets got lost and I don't
see a use-after-free) but as erroneous trigger of debug check.
Add a mutex to force strict ordering: the task that calls tcp_twsk_purge()
blocks other task from doing final _dec_and_test before mutex-owner has
removed all tw sockets of dying netns.
Fixes: e9bd0cca09 ("tcp: Don't allocate tcp_death_row outside of struct netns_ipv4.")
Reported-by: syzbot+8ea26396ff85d23a8929@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/0000000000003a5292061f5e4e19@google.com/
Link: https://lore.kernel.org/netdev/20240812140104.GA21559@breakpoint.cc/
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240812222857.29837-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50e2907ef8bb52cf80ecde9eec5c4dac07177146 ]
TCP ehash table is often sparsely populated.
inet_twsk_purge() spends too much time calling cond_resched().
This patch can reduce time spent in inet_twsk_purge() by 20x.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240327191206.508114-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 565d121b6998 ("tcp: prevent concurrent execution of tcp_sk_exit_batch")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7167395a4be7930ecac6a33b4e54d7e3dd9ee209 ]
Currently, we only check the latest senders's exit code. If the receiver
report failed, it is not recoreded. Fix it by checking the exit code
of all the involved processes.
Before:
bad GRO lookup ok
multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
failed
$ echo $?
0
After:
bad GRO lookup ok
multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
failed
$ echo $?
1
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bdd9fd29cb0f136b307559a19c107210ad5c314 ]
The sockets used by udpgso_bench_tx aren't always ready when
udpgso_bench_tx transmits packets. This issue is more prevalent in -rt
kernels, but can occur in both. Replace the hacky sleep calls with a
function that checks whether the ports in the namespace are ready for
use.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Lucas Karpinski <lkarpins@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7167395a4be7 ("selftests: udpgro: report error when receive failed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0c9fe5eecc97680323ee83780ea3eaf440ba1b7 ]
Since commit 255c1c7279 ("tc-testing: Allow test cases to be skipped")
the variable test_ordinal doesn't exist in call_pre_case().
So it should not be accessed when an exception occurs.
This resolves the following splat:
...
During handling of the above exception, another exception occurred:
Traceback (most recent call last):
File ".../tdc.py", line 1028, in <module>
main()
File ".../tdc.py", line 1022, in main
set_operation_mode(pm, parser, args, remaining)
File ".../tdc.py", line 966, in set_operation_mode
catresults = test_runner_serial(pm, args, alltests)
File ".../tdc.py", line 642, in test_runner_serial
(index, tsr) = test_runner(pm, args, alltests)
File ".../tdc.py", line 536, in test_runner
res = run_one_test(pm, args, index, tidx)
File ".../tdc.py", line 419, in run_one_test
pm.call_pre_case(tidx)
File ".../tdc.py", line 146, in call_pre_case
print('test_ordinal is {}'.format(test_ordinal))
NameError: name 'test_ordinal' is not defined
Fixes: 255c1c7279 ("tc-testing: Allow test cases to be skipped")
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20240815-tdc-test-ordinal-v1-1-0255c122a427@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e12ac3beb0dd3a718296b2d8af5528e9ab728e ]
As explained by Horatiu Vultur in commit 603ead96582d ("net: sparx5: Add
spinlock for frame transmission from CPU") which is for a similar
hardware design, multiple CPUs can simultaneously perform injection
or extraction. There are only 2 register groups for injection and 2
for extraction, and the driver only uses one of each. So we'd better
serialize access using spin locks, otherwise frame corruption is
possible.
Note that unlike in sparx5, FDMA in ocelot does not have this issue
because struct ocelot_fdma_tx_ring already contains an xmit_lock.
I guess this is mostly a problem for NXP LS1028A, as that is dual core.
I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka
the felix DSA driver) started using register-based packet injection and
extraction.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1b9e80236c540fa85d76e2d510d1b38e1968c5d ]
There are 2 distinct code paths (listed below) in the source code which
set up an injection header for Ocelot(-like) switches. Code path (2)
lacks the QoS class and source port being set correctly. Especially the
improper QoS classification is a problem for the "ocelot-8021q"
alternative DSA tagging protocol, because we support tc-taprio and each
packet needs to be scheduled precisely through its time slot. This
includes PTP, which is normally assigned to a traffic class other than
0, but would be sent through TC 0 nonetheless.
The code paths are:
(1) ocelot_xmit_common() from net/dsa/tag_ocelot.c - called only by the
standard "ocelot" DSA tagging protocol which uses NPI-based
injection - sets up bit fields in the tag manually to account for
a small difference (destination port offset) between Ocelot and
Seville. Namely, ocelot_ifh_set_dest() is omitted out of
ocelot_xmit_common(), because there's also seville_ifh_set_dest().
(2) ocelot_ifh_set_basic(), called by:
- ocelot_fdma_prepare_skb() for FDMA transmission of the ocelot
switchdev driver
- ocelot_port_xmit() -> ocelot_port_inject_frame() for
register-based transmission of the ocelot switchdev driver
- felix_port_deferred_xmit() -> ocelot_port_inject_frame() for the
DSA tagger ocelot-8021q when it must transmit PTP frames (also
through register-based injection).
sets the bit fields according to its own logic.
The problem is that (2) doesn't call ocelot_ifh_set_qos_class().
Copying that logic from ocelot_xmit_common() fixes that.
Unfortunately, although desirable, it is not easily possible to
de-duplicate code paths (1) and (2), and make net/dsa/tag_ocelot.c
directly call ocelot_ifh_set_basic()), because of the ocelot/seville
difference. This is the "minimal" fix with some logic duplicated (but
at least more consolidated).
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67c3ca2c5cfe6a50772514e3349b5e7b3b0fac03 ]
Problem description
-------------------
On an NXP LS1028A (felix DSA driver) with the following configuration:
- ocelot-8021q tagging protocol
- VLAN-aware bridge (with STP) spanning at least swp0 and swp1
- 8021q VLAN upper interfaces on swp0 and swp1: swp0.700, swp1.700
- ptp4l on swp0.700 and swp1.700
we see that the ptp4l instances do not see each other's traffic,
and they all go to the grand master state due to the
ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES condition.
Jumping to the conclusion for the impatient
-------------------------------------------
There is a zero-day bug in the ocelot switchdev driver in the way it
handles VLAN-tagged packet injection. The correct logic already exists in
the source code, in function ocelot_xmit_get_vlan_info() added by commit
5ca721c54d ("net: dsa: tag_ocelot: set the classified VLAN during xmit").
But it is used only for normal NPI-based injection with the DSA "ocelot"
tagging protocol. The other injection code paths (register-based and
FDMA-based) roll their own wrong logic. This affects and was noticed on
the DSA "ocelot-8021q" protocol because it uses register-based injection.
By moving ocelot_xmit_get_vlan_info() to a place that's common for both
the DSA tagger and the ocelot switch library, it can also be called from
ocelot_port_inject_frame() in ocelot.c.
We need to touch the lines with ocelot_ifh_port_set()'s prototype
anyway, so let's rename it to something clearer regarding what it does,
and add a kernel-doc. ocelot_ifh_set_basic() should do.
Investigation notes
-------------------
Debugging reveals that PTP event (aka those carrying timestamps, like
Sync) frames injected into swp0.700 (but also swp1.700) hit the wire
with two VLAN tags:
00000000: 01 1b 19 00 00 00 00 01 02 03 04 05 81 00 02 bc
~~~~~~~~~~~
00000010: 81 00 02 bc 88 f7 00 12 00 2c 00 00 02 00 00 00
~~~~~~~~~~~
00000020: 00 00 00 00 00 00 00 00 00 00 00 01 02 ff fe 03
00000030: 04 05 00 01 00 04 00 00 00 00 00 00 00 00 00 00
00000040: 00 00
The second (unexpected) VLAN tag makes felix_check_xtr_pkt() ->
ptp_classify_raw() fail to see these as PTP packets at the link
partner's receiving end, and return PTP_CLASS_NONE (because the BPF
classifier is not written to expect 2 VLAN tags).
The reason why packets have 2 VLAN tags is because the transmission
code treats VLAN incorrectly.
Neither ocelot switchdev, nor felix DSA, declare the NETIF_F_HW_VLAN_CTAG_TX
feature. Therefore, at xmit time, all VLANs should be in the skb head,
and none should be in the hwaccel area. This is done by:
static struct sk_buff *validate_xmit_vlan(struct sk_buff *skb,
netdev_features_t features)
{
if (skb_vlan_tag_present(skb) &&
!vlan_hw_offload_capable(features, skb->vlan_proto))
skb = __vlan_hwaccel_push_inside(skb);
return skb;
}
But ocelot_port_inject_frame() handles things incorrectly:
ocelot_ifh_port_set(ifh, port, rew_op, skb_vlan_tag_get(skb));
void ocelot_ifh_port_set(struct sk_buff *skb, void *ifh, int port, u32 rew_op)
{
(...)
if (vlan_tag)
ocelot_ifh_set_vlan_tci(ifh, vlan_tag);
(...)
}
The way __vlan_hwaccel_push_inside() pushes the tag inside the skb head
is by calling:
static inline void __vlan_hwaccel_clear_tag(struct sk_buff *skb)
{
skb->vlan_present = 0;
}
which does _not_ zero out skb->vlan_tci as seen by skb_vlan_tag_get().
This means that ocelot, when it calls skb_vlan_tag_get(), sees
(and uses) a residual skb->vlan_tci, while the same VLAN tag is
_already_ in the skb head.
The trivial fix for double VLAN headers is to replace the content of
ocelot_ifh_port_set() with:
if (skb_vlan_tag_present(skb))
ocelot_ifh_set_vlan_tci(ifh, skb_vlan_tag_get(skb));
but this would not be correct either, because, as mentioned,
vlan_hw_offload_capable() is false for us, so we'd be inserting dead
code and we'd always transmit packets with VID=0 in the injection frame
header.
I can't actually test the ocelot switchdev driver and rely exclusively
on code inspection, but I don't think traffic from 8021q uppers has ever
been injected properly, and not double-tagged. Thus I'm blaming the
introduction of VLAN fields in the injection header - early driver code.
As hinted at in the early conclusion, what we _want_ to happen for
VLAN transmission was already described once in commit 5ca721c54d
("net: dsa: tag_ocelot: set the classified VLAN during xmit").
ocelot_xmit_get_vlan_info() intends to ensure that if the port through
which we're transmitting is under a VLAN-aware bridge, the outer VLAN
tag from the skb head is stripped from there and inserted into the
injection frame header (so that the packet is processed in hardware
through that actual VLAN). And in all other cases, the packet is sent
with VID=0 in the injection frame header, since the port is VLAN-unaware
and has logic to strip this VID on egress (making it invisible to the
wire).
Fixes: 08d02364b1 ("net: mscc: fix the injection header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bcf2e4aca ]
ocelot_xmit_get_vlan_info() calls __skb_vlan_pop() as the most
appropriate helper I could find which strips away a VLAN header.
That's all I need it to do, but __skb_vlan_pop() has more logic, which
will become incompatible with the future revert of commit 6d1ccff627
("net: reset mac header in dev_start_xmit()").
Namely, it performs a sanity check on skb_mac_header(), which will stop
being set after the above revert, so it will return an error instead of
removing the VLAN tag.
ocelot_xmit_get_vlan_info() gets called in 2 circumstances:
(1) the port is under a VLAN-aware bridge and the bridge sends
VLAN-tagged packets
(2) the port is under a VLAN-aware bridge and somebody else (an 8021q
upper) sends VLAN-tagged packets (using a VID that isn't in the
bridge vlan tables)
In case (1), there is actually no bug to defend against, because
br_dev_xmit() calls skb_reset_mac_header() and things continue to work.
However, in case (2), illustrated using the commands below, it can be
seen that our intervention is needed, since __skb_vlan_pop() complains:
$ ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
$ ip link set $eth master br0 && ip link set $eth up
$ ip link add link $eth name $eth.100 type vlan id 100 && ip link set $eth.100 up
$ ip addr add 192.168.100.1/24 dev $eth.100
I could fend off the checks in __skb_vlan_pop() with some
skb_mac_header_was_set() calls, but seeing how few callers of
__skb_vlan_pop() there are from TX paths, that seems rather
unproductive.
As an alternative solution, extract the bare minimum logic to strip a
VLAN header, and move it to a new helper named vlan_remove_tag(), close
to the definition of vlan_insert_tag(). Document it appropriately and
make ocelot_xmit_get_vlan_info() call this smaller helper instead.
Seeing that it doesn't appear illegal to test skb->protocol in the TX
path, I guess it would be a good for vlan_remove_tag() to also absorb
the vlan_set_encap_proto() function call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 67c3ca2c5cfe ("net: mscc: ocelot: use ocelot_xmit_get_vlan_info() also for FDMA and register injection")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eabb1494c9 ]
skb_mac_header() will no longer be available in the TX path when
reverting commit 6d1ccff627 ("net: reset mac header in
dev_start_xmit()"). As preparation for that, let's use
skb_vlan_eth_hdr() to get to the VLAN header instead, which assumes it's
located at skb->data (assumption which holds true here).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 67c3ca2c5cfe ("net: mscc: ocelot: use ocelot_xmit_get_vlan_info() also for FDMA and register injection")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28cd47f75185c4818b0fb1b46f2f02faaba96376 ]
SMP initiator role shall be considered the one that initiates the
pairing procedure with SMP_CMD_PAIRING_REQ:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 3, Part H
page 1557:
Figure 2.1: LE pairing phases
Note that by sending SMP_CMD_SECURITY_REQ it doesn't change the role to
be Initiator.
Link: https://github.com/bluez/bluez/issues/567
Fixes: b28b494366 ("Bluetooth: Add strict checks for allowed SMP PDUs")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 932021a11805b9da4bd6abf66fe233cccd59fe0e ]
Function hci_sched_le needs to update the respective counter variable
inplace other the likes of hci_quote_sent would attempt to use the
possible outdated value of conn->{le_cnt,acl_cnt}.
Link: https://github.com/bluez/bluez/issues/915
Fixes: 73d80deb7b ("Bluetooth: prioritizing data over HCI")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc923d594db21bee0ead128eb4bb78f7e77467a4 ]
There is a small window in ssam_serial_hub_probe() where the controller
is initialized but has not been started yet. Specifically, between
ssam_controller_init() and ssam_controller_start(). Any failure in this
window, for example caused by a failure of serdev_device_open(),
currently results in an incorrect warning being emitted.
In particular, any failure in this window results in the controller
being destroyed via ssam_controller_destroy(). This function checks the
state of the controller and, in an attempt to validate that the
controller has been cleanly shut down before we try and deallocate any
resources, emits a warning if that state is not SSAM_CONTROLLER_STOPPED.
However, since we have only just initialized the controller and have not
yet started it, its state is SSAM_CONTROLLER_INITIALIZED. Note that this
is the only point at which the controller has this state, as it will
change after we start the controller with ssam_controller_start() and
never revert back. Further, at this point no communication has taken
place and the sender and receiver threads have not been started yet (and
we may not even have an open serdev device either).
Therefore, it is perfectly safe to call ssam_controller_destroy() with a
state of SSAM_CONTROLLER_INITIALIZED. This, however, means that the
warning currently being emitted is incorrect. Fix it by extending the
check.
Fixes: c167b9c7e3 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20240811124645.246016-1-luzmaximilian@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56fb276d0244d430496f249335a44ae114dd5f54 ]
[why & how]
When the commit 9d84c7ef8a ("drm/amd/display: Correct cursor position
on horizontal mirror") was introduced, it used the wrong calculation for
the position copy for X. This commit uses the correct calculation for that
based on the original patch.
Fixes: 9d84c7ef8a ("drm/amd/display: Correct cursor position on horizontal mirror")
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8f9b23abbae5ffcd64856facd26a86b67195bc2f)
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46a6e10a1ab16cc71d4a3cab73e79aabadd6b8ea ]
If we a find that an extent is shared but its end offset is not sector
size aligned, then we don't clone it and issue write operations instead.
This is because the reflink (remap_file_range) operation does not allow
to clone unaligned ranges, except if the end offset of the range matches
the i_size of the source and destination files (and the start offset is
sector size aligned).
While this is not incorrect because send can only guarantee that a file
has the same data in the source and destination snapshots, it's not
optimal and generates confusion and surprising behaviour for users.
For example, running this test:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV
mount $DEV $MNT
# Use a file size not aligned to any possible sector size.
file_size=$((1 * 1024 * 1024 + 5)) # 1MB + 5 bytes
dd if=/dev/random of=$MNT/foo bs=$file_size count=1
cp --reflink=always $MNT/foo $MNT/bar
btrfs subvolume snapshot -r $MNT/ $MNT/snap
rm -f /tmp/send-test
btrfs send -f /tmp/send-test $MNT/snap
umount $MNT
mkfs.btrfs -f $DEV
mount $DEV $MNT
btrfs receive -vv -f /tmp/send-test $MNT
xfs_io -r -c "fiemap -v" $MNT/snap/bar
umount $MNT
Gives the following result:
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
write bar - offset=0 length=49152
write bar - offset=49152 length=49152
write bar - offset=98304 length=49152
write bar - offset=147456 length=49152
write bar - offset=196608 length=49152
write bar - offset=245760 length=49152
write bar - offset=294912 length=49152
write bar - offset=344064 length=49152
write bar - offset=393216 length=49152
write bar - offset=442368 length=49152
write bar - offset=491520 length=49152
write bar - offset=540672 length=49152
write bar - offset=589824 length=49152
write bar - offset=638976 length=49152
write bar - offset=688128 length=49152
write bar - offset=737280 length=49152
write bar - offset=786432 length=49152
write bar - offset=835584 length=49152
write bar - offset=884736 length=49152
write bar - offset=933888 length=49152
write bar - offset=983040 length=49152
write bar - offset=1032192 length=16389
chown bar - uid=0, gid=0
chmod bar - mode=0644
utimes bar
utimes
BTRFS_IOC_SET_RECEIVED_SUBVOL uuid=06d640da-9ca1-604c-b87c-3375175a8eb3, stransid=7
/mnt/sdi/snap/bar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..2055]: 26624..28679 2056 0x1
There's no clone operation to clone extents from the file foo into file
bar and fiemap confirms there's no shared flag (0x2000).
So update send_write_or_clone() so that it proceeds with cloning if the
source and destination ranges end at the i_size of the respective files.
After this changes the result of the test is:
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
clone bar - source=foo source offset=0 offset=0 length=1048581
chown bar - uid=0, gid=0
chmod bar - mode=0644
utimes bar
utimes
BTRFS_IOC_SET_RECEIVED_SUBVOL uuid=582420f3-ea7d-564e-bbe5-ce440d622190, stransid=7
/mnt/sdi/snap/bar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..2055]: 26624..28679 2056 0x2001
A test case for fstests will also follow up soon.
Link: https://github.com/kdave/btrfs-progs/issues/572#issuecomment-2282841416
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e00422ee62663e31e611d7de4d2c4aa3f8555f2 ]
The block size stored in the super block is used by subsystems outside
of btrfs and it's a copy of fs_info::sectorsize. Unify that to always
use our sectorsize, with the exception of mount where we first need to
use fixed values (4K) until we read the super block and can set the
sectorsize.
Replace all uses, in most cases it's fewer pointer indirections.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: 46a6e10a1ab1 ("btrfs: send: allow cloning non-aligned extent if it ends at i_size")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58a63729c957621f1990c3494c702711188ca347 ]
After napi_complete_done() is called when NAPI is polling in the current
process context, another NAPI may be scheduled and start running in
softirq on another CPU and may ring the doorbell before the current CPU
does. When combined with unnecessary rings when there is no need to arm
the CQ, it triggers error paths in the hardware.
This patch fixes this by calling napi_complete_done() after doorbell
rings. It limits the number of unnecessary rings when there is
no need to arm. MANA hardware specifies that there must be one doorbell
ring every 8 CQ wraparounds. This driver guarantees one doorbell ring as
soon as the number of consumed CQEs exceeds 4 CQ wraparounds. In practical
workloads, the 4 CQ wraparounds proves to be big enough that it rarely
exceeds this limit before all the napi weight is consumed.
To implement this, add a per-CQ counter cq->work_done_since_doorbell,
and make sure the CQ is armed as soon as passing 4 wraparounds of the CQ.
Cc: stable@vger.kernel.org
Fixes: e1b5683ff6 ("net: mana: Move NAPI from EQ to CQ")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Link: https://patch.msgid.link/1723219138-29887-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e1fd567d32fcf7544c6e09e0e5bc6c650da6e23 ]
This commit changes device mapper, so that it returns -ERESTARTSYS
instead of -EINTR when it is interrupted by a signal (so that the ioctl
can be restarted).
The manpage signal(7) says that the ioctl function should be restarted if
the signal was handled with SA_RESTART.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14d069d92951a3e150c0a81f2ca3b93e54da913b ]
On ACPI machines, the tegra i2c module encounters an issue due to a
mutex being called inside a spinlock. This leads to the following bug:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585
...
Call trace:
__might_sleep
__mutex_lock_common
mutex_lock_nested
acpi_subsys_runtime_resume
rpm_resume
tegra_i2c_xfer
The problem arises because during __pm_runtime_resume(), the spinlock
&dev->power.lock is acquired before rpm_resume() is called. Later,
rpm_resume() invokes acpi_subsys_runtime_resume(), which relies on
mutexes, triggering the error.
To address this issue, devices on ACPI are now marked as not IRQ-safe,
considering the dependency of acpi_subsys_runtime_resume() on mutexes.
Fixes: bd2fdedbf2 ("i2c: tegra: Add the ACPI support")
Cc: <stable@vger.kernel.org> # v5.17+
Co-developed-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f5d68c859 ]
Save a bit of code for older Tegra platforms by compiling out
VI's I2C mode support that's used only for Tegra210.
$ size i2c-tegra.o
text data bss dec hex filename
11381 292 8 11681 2da1 i2c-tegra.o (full)
10193 292 8 10493 28fd i2c-tegra.o (no-dvc)
9145 292 8 9445 24e5 i2c-tegra.o (no-vi,no-dvc)
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 14d069d92951 ("i2c: tegra: Do not mark ACPI devices as irq safe")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a55efa7edf ]
Save a bit of code for newer Tegra platforms by compiling out
DVC's I2C mode support that's used only for Tegra2.
$ size i2c-tegra.o
text data bss dec hex filename
- 11381 292 8 11681 2da1 i2c-tegra.o
+ 10193 292 8 10493 28fd i2c-tegra.o
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 14d069d92951 ("i2c: tegra: Do not mark ACPI devices as irq safe")
Signed-off-by: Sasha Levin <sashal@kernel.org>
