commit d73a9b3001 upstream.
Add an unusual_devs entry for the Samsung YP-CP3 MP4 player.
User was getting the following errors in dmesg:
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: USB disconnect, address 2
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb:<2>ldm_validate_partition_table(): Disk read failed.
Dev sdb: unable to read RDB block 0
unable to read partition table
Signed-off-by: Vitaly Kuznetsov <vitty@altlinux.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ecc1624a2f upstream.
Fabio Battaglia report that he has another cable that works with this
driver, so this patch adds its vendor/product ID.
Signed-off-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 462e635e5b upstream.
The install_special_mapping routine (used, for example, to setup the
vdso) skips the security check before insert_vm_struct, allowing a local
attacker to bypass the mmap_min_addr security restriction by limiting
the available pages for special mappings.
bprm_mm_init() also skips the check, and although I don't think this can
be used to bypass any restrictions, I don't see any reason not to have
the security check.
$ uname -m
x86_64
$ cat /proc/sys/vm/mmap_min_addr
65536
$ cat install_special_mapping.s
section .bss
resb BSS_SIZE
section .text
global _start
_start:
mov eax, __NR_pause
int 0x80
$ nasm -D__NR_pause=29 -DBSS_SIZE=0xfffed000 -f elf -o install_special_mapping.o install_special_mapping.s
$ ld -m elf_i386 -Ttext=0x10000 -Tbss=0x11000 -o install_special_mapping install_special_mapping.o
$ ./install_special_mapping &
[1] 14303
$ cat /proc/14303/maps
0000f000-00010000 r-xp 00000000 00:00 0 [vdso]
00010000-00011000 r-xp 00001000 00:19 2453665 /home/taviso/install_special_mapping
00011000-ffffe000 rwxp 00000000 00:00 0 [stack]
It's worth noting that Red Hat are shipping with mmap_min_addr set to
4096.
Signed-off-by: Tavis Ormandy <taviso@google.com>
Acked-by: Kees Cook <kees@ubuntu.com>
Acked-by: Robert Swiecki <swiecki@google.com>
[ Changed to not drop the error code - akpm ]
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3bfa321e66 upstream.
Lenovo S10-3t's ClickPad is a 2-button ClickPad that reports BTN_LEFT
and BTN_RIGHT as normal touchpad, unlike the 1-button ClickPad used in
HP mini 210 that reports solely BTN_MIDDLE.
In 0xc0-cap response, the 1-button ClickPad has the 20-bit set while
2-button ClickPad has the 8-bit set.
This patch makes the kernel only handle 1-button ClickPad specially,
and treat 2-button ClickPad in the same fashion as regular touchpads.
This fixes kernel bug #18122 and MeeGo bug #4807.
Signed-off-by: Yan Li <yan.i.li@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6027277e77 upstream.
Add a quirk entry for Thinkpad Edge 11 as well as other TP Edge models.
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8d1331b37d upstream.
During initialization each driver reads the default TX power
for each individual channel. However mac80211 only accepts the
maximum value (which is also handled as default value).
As a result, the TX power of the device was being limited to
the default value, which is often quite low compared to the
real maximum acceptable value.
This patch allows each driver to set the maximum value on a
per-channel basis which is forwarded to mac80211. The default
value will be preserved for now, in case we want to update
mac80211 to differentiate between the maximum and default txpower.
This fixes bug complaining about limited TX power values like:
https://bugzilla.kernel.org/show_bug.cgi?id=16358
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 254e42006c upstream.
On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.
During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).
Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the system to hang.
Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com>
Reported-by: Max Asbock <masbock@linux.vnet.ibm.com>
Reported-and-tested-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 086e8ced65 upstream.
In x2apic mode, we need to set the upper address register of the fault
handling interrupt register of the vt-d hardware. Without this
irq migration of the vt-d fault handling interrupt is broken.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <1291225233.2648.39.camel@sbsiddha-MOBL3>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Tested-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7f99d946e7 upstream.
Fault handling is getting enabled after enabling the interrupt-remapping (as
the success of interrupt-remapping can affect the apic mode and hence the
fault handling mode).
Hence there can potentially be some faults between the window of enabling
interrupt-remapping in the vt-d and the fault-handling of the vt-d units.
Handle any previous faults after enabling the vt-d fault handling.
For v2.6.38 cleanup, need to check if we can remove the dmar_fault() in the
enable_intr_remapping() and see if we can enable fault handling along with
enabling intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101201062244.630417138@intel.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7f7fbf45c6 upstream.
Interrupt-remapping gets enabled very early in the boot, as it determines the
apic mode that the processor can use. And the current code enables the vt-d
fault handling before the setup_local_APIC(). And hence the APIC LDR registers
and data structure in the memory may not be initialized. So the vt-d fault
handling in logical xapic/x2apic modes were broken.
Fix this by enabling the vt-d fault handling in the end_local_APIC_setup()
A cleaner fix of enabling fault handling while enabling intr-remapping
will be addressed for v2.6.38. [ Enabling intr-remapping determines the
usage of x2apic mode and the apic mode determines the fault-handling
configuration. ]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <20101201062244.541996375@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit de2a8cf98e upstream.
The vdso Makefile passes linker-style -m options not to the linker but
to gcc. This happens to work with earlier gcc, but fails with gcc
4.6. Pass gcc-style -m options, instead.
Note: all currently supported versions of gcc supports -m32, so there
is no reason to conditionalize it any more.
Reported-by: H. J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <tip-*@git.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit bc4cf2bb27 upstream.
Previously we were just setting up the "tp" register in the
new task as started by clone() in libc. However, this is not
quite right, since in principle a signal might be delivered to
the new task before it had its TLS set up. (Of course, this race
window still exists for resetting the libc getpid() cached value
in the new task, in principle. But in any case, we are now doing
this exactly the way all other architectures do it.)
This change is important for 2.6.37 since the tile glibc we will
be submitting upstream will not set TLS in user space any more,
so it will only work on a kernel that has this fix. It should
also be taken for 2.6.36.x in the stable tree if possible.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 364829b126 upstream.
The file_ops struct for the "trace" special file defined llseek as seq_lseek().
However, if the file was opened for writing only, seq_open() was not called,
and the seek would dereference a null pointer, file->private_data.
This patch introduces a new wrapper for seq_lseek() which checks if the file
descriptor is opened for reading first. If not, it does nothing.
Signed-off-by: Slava Pestov <slavapestov@google.com>
LKML-Reference: <1290640396-24179-1-git-send-email-slavapestov@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 589a594be1 upstream.
When we fail to start a raid10 for some reason, we call
md_unregister_thread to kill the thread that was created.
Unfortunately md_thread() will then make one call into the handler
(raid10d) even though md_wakeup_thread has not been called. This is
not safe and as md_unregister_thread is called after mddev->private
has been set to NULL, it will definitely cause a NULL dereference.
So fix this at both ends:
- md_thread should only call the handler if THREAD_WAKEUP has been
set.
- raid10 should call md_unregister_thread before setting things
to NULL just like all the other raid modules do.
This is applicable to 2.6.35 and later.
Reported-by: "Citizen" <citizen_lee@thecus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1a855a0606 upstream.
With v0.90 metadata, a hot-spare does not become a full member of the
array until recovery is complete. So if we re-add such a device to
the array, we know that all of it is as up-to-date as the event count
would suggest, and so it a bitmap-based recovery is possible.
However with v1.x metadata, the hot-spare immediately becomes a full
member of the array, but it record how much of the device has been
recovered. If the array is stopped and re-assembled recovery starts
from this point.
When such a device is hot-added to an array we currently lose the 'how
much is recovered' information and incorrectly included it as a full
in-sync member (after bitmap-based fixup).
This is wrong and unsafe and could corrupt data.
So be more careful about setting saved_raid_disk - which is what
guides the re-adding of devices back into an array.
The new code matches the code in slot_store which does a similar
thing, which is encouraging.
This is suitable for any -stable kernel.
Reported-by: "Dailey, Nate" <Nate.Dailey@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[The mainline kernel doesn't have this problem. Commit "(23588c3) x86,
amd: Add support for CPUID topology extension of AMD CPUs" removed the
family check. But 2.6.32.y needs to be fixed.]
This CPU family check is not required -- existence of the NodeId MSR
is indicated by a CPUID feature flag which is already checked in
amd_fixup_dcm() -- and it needlessly prevents amd_fixup_dcm() to be
called for newer AMD CPUs.
In worst case this can lead to a panic in the scheduler code for AMD
family 0x15 multi-node AMD CPUs. I just have a picture of VGA console
output so I can't copy-and-paste it herein, but the call stack of such
a panic looked like:
do_divide_error
...
find_busiest_group
run_rebalance_domains
...
apic_timer_interrupt
...
cpu_idle
The mainline kernel doesn't have this problem. Commit "(23588c3) x86,
amd: Add support for CPUID topology extension of AMD CPUs" removed the
family check. But 2.6.32.y needs to be fixed.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ba34fcee47 upstream.
... and interface up.
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0a54917c3f upstream.
Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a2ae4cc9a1 upstream.
If inotify_init is unable to allocate a new file for the new inotify
group we leak the new group. This patch drops the reference on the
group on file allocation failure.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f08f5a0add upstream.
There are some situations (e.g. in __pm_generic_call()), where
pm_runtime_suspended() is used to decide whether or not to execute
a device's (system) ->suspend() callback. The callback is not
executed if pm_runtime_suspended() returns true, but it does so
for devices that don't even support runtime PM, because the
power.disable_depth device field is ignored by it. This leads to
problems (i.e. devices are not suspened when they should), so rework
pm_runtime_suspended() so that it returns false if the device's
power.disable_depth field is different from zero.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0f004f5a69 upstream.
There's a long-running regression that proved difficult to fix and
which is hitting certain people and is rather annoying in its effects.
Damien reported that after 74f5187ac8 (sched: Cure load average vs
NO_HZ woes) his load average is unnaturally high, he also noted that
even with that patch reverted the load avgerage numbers are not
correct.
The problem is that the previous patch only solved half the NO_HZ
problem, it addressed the part of going into NO_HZ mode, not of
comming out of NO_HZ mode. This patch implements that missing half.
When comming out of NO_HZ mode there are two important things to take
care of:
- Folding the pending idle delta into the global active count.
- Correctly aging the averages for the idle-duration.
So with this patch the NO_HZ interaction should be complete and
behaviour between CONFIG_NO_HZ=[yn] should be equivalent.
Furthermore, this patch slightly changes the load average computation
by adding a rounding term to the fixed point multiplication.
Reported-by: Damien Wyart <damien.wyart@free.fr>
Reported-by: Tim McGrath <tmhikaru@gmail.com>
Tested-by: Damien Wyart <damien.wyart@free.fr>
Tested-by: Orion Poplawski <orion@cora.nwra.com>
Tested-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Chase Douglas <chase.douglas@canonical.com>
LKML-Reference: <1291129145.32004.874.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 49f4138346 upstream.
wake_up_klogd() may get called from preemptible context but uses
__raw_get_cpu_var() to write to a per cpu variable. If it gets preempted
between getting the address and writing to it, the cpu in question could be
offline if the process gets scheduled back and hence writes to the per cpu data
of an offline cpu.
This buggy behaviour was introduced with fa33507a "printk: robustify
printk, fix#2" which was supposed to fix a "using smp_processor_id() in
preemptible" warning.
Let's use this_cpu_write() instead which disables preemption and makes sure
that the outlined scenario cannot happen.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20101126124247.GC7023@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ab838338a2 upstream.
The old code generated an interrupt storm bad enough to completely
take down my system.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8df3fc981d upstream.
Some Panasonic Toughbooks create nodes in module level code.
Module level code is the executable AML code outside of control method,
for example, below AML code creates a node \_SB.PCI0.GFX0.DD02.CUBL
If (\_OSI ("Windows 2006"))
{
Scope (\_SB.PCI0.GFX0.DD02)
{
Name (CUBL, Ones)
...
}
}
Scope() op does not actually create a new object, it refers to an
existing object(\_SB.PCI0.GFX0.DD02 in above example). However, for
Scope(), we want to indeed open a new scope, so the child nodes(CUBL in
above example) can be created correctly under it.
https://bugzilla.kernel.org/show_bug.cgi?id=19462
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 67286640f6 ]
packet_getname_spkt() doesn't initialize all members of sa_data field of
sockaddr struct if strlen(dev->name) < 13. This structure is then copied
to userland. It leads to leaking of contents of kernel stack memory.
We have to fully fill sa_data with strncpy() instead of strlcpy().
The same with packet_getname(): it doesn't initialize sll_pkttype field of
sockaddr_ll. Set it to zero.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 1f18b7176e]
Parameter 'len' is size_t type so it will never get negative.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 332dd96f7a ]
Followup of commit ef885afbf8 (net: use rcu_barrier() in
rollback_registered_many)
dst_dev_event() scans a garbage dst list that might be feeded by various
network notifiers at device dismantle time.
Its important to call dst_dev_event() after other notifiers, or we might
enter the infamous msleep(250) in netdev_wait_allrefs(), and wait one
second before calling again call_netdevice_notifiers(NETDEV_UNREGISTER,
dev) to properly remove last device references.
Use priority -10 to let dst_dev_notifier be called after other network
notifiers (they have the default 0 priority)
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Octavian Purdila <opurdila@ixiacom.com>
Reported-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 46814e08d8 ]
My conversion of tehuti to use request_firmware() was confused about
the filename of the firmware blob. Change the driver to match the
blob.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 171995e5d8]
x25 does not decrement the network device reference counts on module unload.
Thus unregistering any pre-existing interface after unloading the x25 module
hangs and results in
unregister_netdevice: waiting for tap0 to become free. Usage count = 1
This patch decrements the reference counts of all interfaces in x25_link_free,
the way it is already done in x25_link_device_down for NETDEV_DOWN events.
Signed-off-by: Apollon Oikonomopoulos <apollon@noc.grnet.gr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit e8d34a884e]
Using the SOCK_DGRAM enum results in
"net-pf-2-proto-SOCK_DGRAM-type-115", so use the numeric value like it
is done in net/dccp.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 75c1c82566 ]
If we break the loop when there are still skbs in tq and no skb in
rq, the skbs will be left in txq until new skbs are enqueued into rq.
In rare cases, no new skb is queued, then these skbs will stay in rq
forever.
After this patch, if tq isn't empty when we break the loop, we goto
resched directly.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 4e085e76cb ]
Unconditional use of skb->dev won't work here,
try to fetch the econet device via skb_dst()->dev
instead.
Suggested by Eric Dumazet.
Reported-by: Nelson Elhage <nelhage@ksplice.com>
Tested-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 0c62fc6dd0]
We need to drop the mutex and do a dev_put, so set an error code and break like
the other paths, instead of returning directly.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 46bcf14f44 ]
Pavel Emelyanov tried to fix a race between sk_filter_(de|at)tach and
sk_clone() in commit 47e958eac2
Problem is we can have several clones sharing a common sk_filter, and
these clones might want to sk_filter_attach() their own filters at the
same time, and can overwrite old_filter->rcu, corrupting RCU queues.
We can not use filter->rcu without being sure no other thread could do
the same thing.
Switch code to a more conventional ref-counting technique : Do the
atomic decrement immediately and queue one rcu call back when last
reference is released.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit c00b2c9e79 ]
Somewhere along the lines net_cls_subsys_id became a macro when
cls_cgroup is built as a module. Not only did it make cls_cgroup
completely useless, it also causes it to crash on module unload.
This patch fixes this by removing that macro.
Thanks to Eric Dumazet for diagnosing this problem.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit af3e5bd5f6 ]
The returned slave is incorrect, if the net device under check is not
charged yet by the master.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit fe10ae5338 ]
Sometimes ax25_getname() doesn't initialize all members of fsa_digipeater
field of fsa struct, also the struct has padding bytes between
sax25_call and sax25_ndigis fields. This structure is then copied to
userland. It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 25888e3031 ]
Its easy to eat all kernel memory and trigger NMI watchdog, using an
exploit program that queues unix sockets on top of others.
lkml ref : http://lkml.org/lkml/2010/11/25/8
This mechanism is used in applications, one choice we have is to have a
recursion limit.
Other limits might be needed as well (if we queue other types of files),
since the passfd mechanism is currently limited by socket receive queue
sizes only.
Add a recursion_level to unix socket, allowing up to 4 levels.
Each time we send an unix socket through sendfd mechanism, we copy its
recursion level (plus one) to receiver. This recursion level is cleared
when socket receive queue is emptied.
Reported-by: Марк Коренберг <socketpair@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 9915672d41 ]
Vegard Nossum found a unix socket OOM was possible, posting an exploit
program.
My analysis is we can eat all LOWMEM memory before unix_gc() being
called from unix_release_sock(). Moreover, the thread blocked in
unix_gc() can consume huge amount of time to perform cleanup because of
huge working set.
One way to handle this is to have a sensible limit on unix_tot_inflight,
tested from wait_for_unix_gc() and to force a call to unix_gc() if this
limit is hit.
This solves the OOM and also reduce overall latencies, and should not
slowdown normal workloads.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Upstream commit 24b7ea9f6c ]
I am not family with RealTek RTL-8139C+ series 10/100 PCI Ethernet driver.
I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(status & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If these are right, driver will set ip_summed with CHECKSUM_UNNECESSARY for other
upper protocol, e.g. sctp, igmp protocol. This will cause protocol stack ignores
checksum check for packets with invalid checksum.
This patch is only compile-test.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
