[ Upstream commit f816b9829b ]
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230510200020.1534610-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f97b8401e0 ]
On some distributions, the rp_filter is automatically set (=1) by
default on a netdev basis (also on VRFs).
In an SRv6 End.DT4 behavior, decapsulated IPv4 packets are routed using
the table associated with the VRF bound to that tunnel. During lookup
operations, the rp_filter can lead to packet loss when activated on the
VRF.
Therefore, we chose to make this selftest more robust by explicitly
disabling the rp_filter during tests (as it is automatically set by some
Linux distributions).
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21a933c79a ]
The srv6_end_dt4_l3vpn_test instantiates a virtual network consisting of
several routers (rt-1, rt-2) and hosts.
When the IPv6 addresses of rt-{1,2} routers are configured, the Deduplicate
Address Detection (DAD) kicks in when enabled in the Linux distros running
the selftests. DAD is used to check whether an IPv6 address is already
assigned in a network. Such a mechanism consists of sending an ICMPv6 Echo
Request and waiting for a reply.
As the DAD process could take too long to complete, it may cause the
failing of some tests carried out by the srv6_end_dt4_l3vpn_test script.
To make the srv6_end_dt4_l3vpn_test more robust, we disable DAD on routers
since we configure the virtual network manually and do not need any address
deduplication mechanism at all.
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf3128a7ac ]
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d776e31c8 ]
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c5a7680e6 ]
struct platform_driver::remove returning an integer made driver authors
expect that returning an error code was proper error handling. However
the driver core ignores the error and continues to remove the device
because there is nothing the core could do anyhow and reentering the
remove callback again is only calling for trouble.
So this is an source for errors typically yielding resource leaks in the
error path.
As there are too many platform drivers to neatly convert them all to
return void in a single go, do it in several steps after this patch:
a) Convert all drivers to implement .remove_new() returning void instead
of .remove() returning int;
b) Change struct platform_driver::remove() to return void and so make
it identical to .remove_new();
c) Change all drivers back to .remove() now with the better prototype;
d) drop struct platform_driver::remove_new().
While this touches all drivers eventually twice, steps a) and c) can be
done one driver after another and so reduces coordination efforts
immensely and simplifies review.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221209150914.3557650-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 17955aba78 ("ASoC: fsl_micfil: Fix error handler with pm_runtime_enable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fc46f9421 ]
This reverts commit b0355dbbf1.
The reverted commit clears the secpath on packets received via xfrm interfaces
to support nested IPsec tunnels. This breaks Netfilter policy matching using
xt_policy in the FORWARD chain, as the secpath is missing during forwarding.
Additionally, Benedict Wong reports that it breaks Transport-in-Tunnel mode.
Fix this regression by reverting the commit until we have a better approach
for nested IPsec tunnels.
Fixes: b0355dbbf1 ("Fix XFRM-I support for nested ESP tunnels")
Link: https://lore.kernel.org/netdev/20230412085615.124791-1-martin@strongswan.org/
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 430cac4874 ]
The current code doesn't let a simple "allow" policy counteract a
default policy blocking all incoming packets:
ip x p setdefault in block
ip x p a src 192.168.2.1/32 dst 192.168.2.2/32 dir in action allow
At this stage, we have an allow policy (with or without transforms)
for this packet. It doesn't matter what the default policy says, since
the policy we looked up lets the packet through. The case of a
blocking policy is already handled separately, so we can remove this
check.
Fixes: 2d151d3907 ("xfrm: Add possibility to set the default to block if we have no policy")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 720b47229a ]
The gfx.cp_ecc_error_irq is retired in gfx11. In gfx_v11_0_hw_fini still
use amdgpu_irq_put to disable this interrupt, which caused the call trace
in this function.
[ 102.873958] Call Trace:
[ 102.873959] <TASK>
[ 102.873961] gfx_v11_0_hw_fini+0x23/0x1e0 [amdgpu]
[ 102.874019] gfx_v11_0_suspend+0xe/0x20 [amdgpu]
[ 102.874072] amdgpu_device_ip_suspend_phase2+0x240/0x460 [amdgpu]
[ 102.874122] amdgpu_device_ip_suspend+0x3d/0x80 [amdgpu]
[ 102.874172] amdgpu_device_pre_asic_reset+0xd9/0x490 [amdgpu]
[ 102.874223] amdgpu_device_gpu_recover.cold+0x548/0xce6 [amdgpu]
[ 102.874321] amdgpu_debugfs_reset_work+0x4c/0x70 [amdgpu]
[ 102.874375] process_one_work+0x21f/0x3f0
[ 102.874377] worker_thread+0x200/0x3e0
[ 102.874378] ? process_one_work+0x3f0/0x3f0
[ 102.874379] kthread+0xfd/0x130
[ 102.874380] ? kthread_complete_and_exit+0x20/0x20
[ 102.874381] ret_from_fork+0x22/0x30
v2:
- Handle umc and gfx ras cases in separated patch
- Retired the gfx_v11_0_cp_ecc_error_irq_funcs in gfx11
v3:
- Improve the subject and code comments
- Add judgment on gfx11 in the function of amdgpu_gfx_ras_late_init
v4:
- Drop the define of CP_ME1_PIPE_INST_ADDR_INTERVAL and
SET_ECC_ME_PIPE_STATE which using in gfx_v11_0_set_cp_ecc_error_state
- Check cp_ecc_error_irq.funcs rather than ip version for a more
sustainable life
v5:
- Simplify judgment conditions
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e9b8992b1 ]
The purpose of this patch is to provide a central location where all
HP related drivers are found. HP drivers will recide under
drivers/platform/x86/hp directory.
Introduce changes to Kconfig file to list all HP driver under "HP X86
Platform Specific Device Drivers" menu option. Additional changes
include update MAINTAINERS file to indicate hp related drivers new
path.
Signed-off-by: Jorge Lopez <jorge.lopez2@hp.com>
Link: https://lore.kernel.org/r/20221020201033.12790-2-jorge.lopez2@hp.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: decab2825c ("platform/x86: hp-wmi: add micmute to hp_wmi_keymap struct")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829632dae8 ]
The panic notifiers' callbacks execute in an atomic context, with
interrupts/preemption disabled, and all CPUs not running the panic
function are off, so it's very dangerous to wait on a regular
spinlock, there's a risk of deadlock.
Refactor the panic notifier of parisc/power driver to make use
of spin_trylock - for that, we've added a second version of the
soft-power function. Also, some comments were reorganized and
trailing white spaces, useless header inclusion and blank lines
were removed.
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jeroen Roovers <jer@xs4all.nl>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ded99b89d2 ]
The Android Lenovo Yoga Book X90F / X90L uses the same charger / fuelgauge
setup as the already supported Windows Lenovo Yoga Book X91F/L, add
a DMI match for this to intel_cht_wc_models with driver_data
set to INTEL_CHT_WC_LENOVO_YOGABOOK1.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230301095402.28582-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e953796251 ]
This reverts commit
443a98e649 ("soundwire: bus: use pm_runtime_resume_and_get()")
Change calls to pm_runtime_resume_and_get() back to pm_runtime_get_sync().
This fixes a usage count underrun caused by doing a pm_runtime_put() even
though pm_runtime_resume_and_get() returned an error.
The three affected functions ignore -EACCES error from trying to get
pm_runtime, and carry on, including a put at the end of the function.
But pm_runtime_resume_and_get() does not increment the usage count if it
returns an error. So in the -EACCES case you must not call
pm_runtime_put().
The documentation for pm_runtime_get_sync() says:
"Consider using pm_runtime_resume_and_get() ... as this is likely to
result in cleaner code."
In this case I don't think it results in cleaner code because the
pm_runtime_put() at the end of the function would have to be conditional on
the return value from pm_runtime_resume_and_get() at the top of the
function.
pm_runtime_get_sync() doesn't have this problem because it always
increments the count, so always needs a put. The code can just flow through
and do the pm_runtime_put() unconditionally.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230406134640.8582-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2367e0ecb4 ]
There are two issues related to the number of ports coming from
Devicetree when exceeding in total QCOM_SDW_MAX_PORTS. Both lead to
incorrect memory accesses:
1. With DTS having too big value of input or output ports, the driver,
when copying port parameters from local/stack arrays into 'pconfig'
array in 'struct qcom_swrm_ctrl', will iterate over their sizes.
2. If DTS also has too many parameters for these ports (e.g.
qcom,ports-sinterval-low), the driver will overflow buffers on the
stack when reading these properties from DTS.
Add a sanity check so incorrect DTS will not cause kernel memory
corruption.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230222144412.237832-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e82793f0 ]
When we unbind a serial port hardware specific 8250 driver, the generic
serial8250 driver takes over the port. After that we see an oops about 10
seconds later. This can produce the following at least on some TI SoCs:
Unhandled fault: imprecise external abort (0x1406)
Internal error: : 1406 [#1] SMP ARM
Turns out that we may still have the serial port hardware specific driver
port->pm in use, and serial8250_pm() tries to call it after the port
specific driver is gone:
serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base]
uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base]
uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c
__tty_hangup.part.0 from disassociate_ctty+0x154/0x20c
disassociate_ctty from do_exit+0x744/0xaac
do_exit from do_group_exit+0x40/0x8c
do_group_exit from __wake_up_parent+0x0/0x1c
Let's fix the issue by calling serial8250_set_defaults() in
serial8250_unregister_port(). This will set the port back to using
the serial8250 default functions, and sets the port->pm to point to
serial8250_pm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230418101407.12403-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dac3b19210 ]
PD3.0 Spec 6.4.4.3.2 say that only Responder supports 12 or more SVIDs,
the Discover SVIDs Command Shall be executed multiple times until a
Discover SVIDs VDO is returned ending either with a SVID value of
0x0000 in the last part of the last VDO or with a VDO containing two
SVIDs with values of 0x0000.
In the current implementation, if the last VDO does not find that the
Discover SVIDs Command would be executed multiple times even if the
Responder SVIDs are less than 12, and we found some odd dockers just
meet this case. So fix it.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Link: https://lore.kernel.org/r/20230316081149.24519-1-frank.wang@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bea407a427 ]
Some devices will include battery status usages in the HID descriptor
but we won't see that battery data for one reason or another. For example,
AES sensors won't send battery data unless an AES pen is in proximity.
If a user does not have an AES pen but instead only interacts with the
AES touchscreen with their fingers then there is no need for us to create
a battery object. Similarly, if a family of peripherals shares the same
HID descriptor between wired-only and wireless-capable SKUs, users of the
former may never see a battery event and will not want a power_supply
object created.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217062
Link: https://gitlab.gnome.org/GNOME/gnome-control-center/-/issues/2354
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 326e1c208f ]
On some ACPI platforms (namely the ASUS Zenbook UM325) the _DSM method must
not be called after a notification is received but instead the mailbox
should be read immediately from RAM. This is because the ACPI interrupt
handler destroys the CCI in ERAM after copying to system memory, and when
_DSM is later called to perform a second copy, it retrieves a garbage
value.
Instead, the _DSM(read) method should only be called when necessary, i.e.
for polling the state after reset and for retrieving the version. Other
reads should not call _DSM and only peek into the RAM region.
This adds a separate read operation for the Zenbook that syncs the
ACPI mailbox only with polled commands.
Link: https://lore.kernel.org/linux-usb/20210823180626.tb6m7h5tp6adhvt2@fastboi.localdomain/
Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
[ heikki : handling everything in ucsi_acpi.c with DMI quirk ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230405134456.49607-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c614175b ]
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20230318222132.3373-1-kgroeneveld@lenbrook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b3691d15e ]
Now that USB HID++ devices can gather a serial number that matches the
one that would be gathered when connected through a Unifying receiver,
remove the last difference by dropping the product ID as devices
usually have different product IDs when connected through USB or
Unifying.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying before patch: 4067-e8-ce-cd-45
- USB before patch: c086-e8-ce-cd-45
- Unifying and USB after patch: e8-ce-cd-45
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230302130117.3975-2-hadess@hadess.net
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ad1fe0da0 ]
For devices that support the 0x0003 feature (Device Information) version 4,
set the serial based on the output of that feature, rather than relying
on the usbhid code setting the USB serial.
This should allow the serial when connected through USB to (nearly)
match the one when connected through a unifying receiver.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying: 4067-e8-ce-cd-45
- USB before patch: 017C385C3837
- USB after patch: c086-e8-ce-cd-45
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230302130117.3975-1-hadess@hadess.net
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 752cbd8f19 ]
Initialize the module parameters, read_timeout and write_timeout once in
init().
Module parameters can only be set once and cannot be modified later, so we
don't need to evaluate them again when passing the parameters to
wait_event_interruptible_timeout().
Convert datatype of {read,write}_timeout from 'int' to 'long int' because
implicit conversion of 'long int' to 'int' in statement
'{read,write}_timeout = MAX_SCHEDULE_TIMEOUT' results in an overflow.
Change format specifier for {read,write}_timeout from %i to %li.
Reviewed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Khadija Kamran <kamrankhadijadj@gmail.com>
Link: https://lore.kernel.org/r/ZBN3XAsItCiTk7CV@khadija-virtual-machine
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3388ddc74 ]
I recently tested several old MacBooks and as far as I can tell, all
MacBooks that have an ISO keyboard have the tilde key quirk:
Product Model Year System CPU Shape Labels Country Quirky
============================================================================
05ac:021b A1181 2006 MacBook2,1 T5600 ISO British 13 Yes
05ac:021b A1181 2007 MacBook2,1 T7200 ISO Québécois 13 Yes
05ac:0229 A1181 2007 MacBook4,1 T8300 ANSI Usonian 33 No
05ac:022a A1181 2007 MacBook4,1 T8100 ISO English 13 Yes
05ac:022a A1181 2007 MacBook5,2 P7350 ISO Québécois 13 Yes
05ac:0237 A1278 2008 MacBook5,1 P7350 ISO Dutch 13 Yes
05ac:0237 A1278 2009 MacBook5,5 P7550 ISO British 13 Yes
The model number and year are from the laptop case. Since Apple printed
the same model and year on many different laptops, the system name (as
reported in the SMBIOS tables) and CPU form a more precise identifier.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91b6d02ddc ]
The ATS2851 based controller advertises support for command "LE Set Random
Private Address Timeout" but does not actually implement it, impeding the
controller initialization.
Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller
initialization.
< HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Status (0x0f) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1
Status: Unknown HCI Command (0x01)
Co-developed-by: imoc <wzj9912@gmail.com>
Signed-off-by: imoc <wzj9912@gmail.com>
Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
