commit 1e4e25c495 upstream.
The subsystem will free the asd memory on notifier cleanup, if the asd is
added to the notifier.
However the memory is freed using kfree.
Thus, we cannot allocate the asd using devm_*
This can lead to crashes and problems.
To test this issue, just return an error at probe, but cleanup the
notifier beforehand.
Fixes: 106267444f ("[media] atmel-isc: add the Image Sensor Controller code")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e926b12c61 upstream.
After a PWM is disposed by its user the per chip data becomes invalid.
Clear the data in common code instead of the device drivers to get
consistent behaviour. Before this patch only three of nine drivers
cleaned up here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f413cbb332 upstream.
Errors are negative numbers. Using %u shows them as very large positive
numbers such as 4294967277 that don't make sense. Use the %d format
instead, and get a much nicer -19.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Fixes: b48e0bab14 ("net: macb: Migrate to devm clock interface")
Fixes: 93b31f48b3 ("net/macb: unify clock management")
Fixes: 421d9df062 ("net/macb: merge at91_ether driver into macb driver")
Fixes: aead88bd0e ("net: ethernet: macb: Add support for rx_clk")
Fixes: f5473d1d44 ("net: macb: Support clock management for tsu_clk")
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0816e5088 upstream.
Control DO_WHITE_BALANCE is a button, with read only and execute-on-write flags.
Adding this control in the proper list in the fill function.
After adding it here, we can see output of v4l2-ctl -L
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86c6739eda upstream.
We leak the page that we use to create skb page fragments
when destroying the xfrm_state. Fix this by dropping a
page reference if a page was assigned to the xfrm_state.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Reported-by: JD <jdtxs00@gmail.com>
Reported-by: Paul Wouters <paul@nohats.ca>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a7ebfa85f upstream.
On zang's Dell XPS 13 9370 after Thunderbolt NVM firmware upgrade the
Thunderbolt controller did not come back as expected. Only after the
system was rebooted it became available again. It is not entirely clear
what happened but I suspect the new NVM firmware image authentication
failed for some reason. Regardless of this the router needs to be power
cycled if NVM authentication fails in order to get it fully functional
again.
This modifies the driver to issue a power cycle in case the NVM
authentication fails immediately when dma_port_flash_update_auth()
returns. We also need to call tb_switch_set_uuid() earlier to be able to
fetch possible NVM authentication failure when DMA port is added.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205457
Reported-by: zang <dump@tzib.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6689f0f4bb upstream.
Testing on different generations of Lantiq MIPS SoC based boards, showed
that it takes up to 1500 us until the core reset bit is cleared.
The driver from the vendor SDK (ifxhcd) uses a 1 second timeout. Use the
same timeout to fix wrong hang detections and make the driver work for
Lantiq MIPS SoCs.
At least till kernel 4.14 the hanging reset only caused a warning but
the driver was probed successful. With kernel 4.19 errors out with
EBUSY.
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1e4580a1d upstream.
Set gck->audio_pll_allowed in at91_clk_register_generated. This makes it
easier to do it from code that is not parsing device tree.
Also, this fixes an issue where the resulting clk_hw can be dereferenced
before being tested for error.
Fixes: 1a1a36d72e ("clk: at91: clk-generated: make gclk determine audio_pll rate")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mainline commit 8fde12ca79 ("mm: prevent get_user_pages() from
overflowing page refcount") was backported to 4.19.y stable as commit
d972ebbf42. The backport however missed that in 4.19, there are several
arch-specific gup.c versions with fast gup implementations, so these do not
prevent refcount overflow.
This stable-only commit fixes the s390 version, and is based on the backport in
SUSE SLES/openSUSE 4.12-based kernels.
The remaining architectures with own gup.c are sparc, mips, sh. It's unlikely
the known overflow scenario based on FUSE, which needs 140GB of RAM, is a
problem for those architectures, and I don't feel confident enough to patch
them.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bda2ab5635 ]
Commit 2b6f0090a3 ("mtd: Check add_mtd_device() ret code") contained
a leftover of the debug session that led to this bug fix. Remove this
pr_info().
Fixes: 2b6f0090a3 ("mtd: Check add_mtd_device() ret code")
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 676e4a6fe7 ]
We want to avoid leaking pointer info from xdp_frame (that is placed in
top of frame) like commit 6dfb970d3d ("xdp: avoid leaking info stored in
frame data on page reuse"), and followup commit 97e19cce05 ("bpf:
reserve xdp_frame size in xdp headroom") that reserve this headroom.
These changes also affected how cpumap constructed SKBs, as xdpf->headroom
size changed, the skb data starting point were in-effect shifted with 32
bytes (sizeof xdp_frame). This was still okay, as the cpumap frame_size
calculation also included xdpf->headroom which were reduced by same amount.
A bug was introduced in commit 77ea5f4cbe ("bpf/cpumap: make sure
frame_size for build_skb is aligned if headroom isn't"), where the
xdpf->headroom became part of the SKB_DATA_ALIGN rounding up. This
round-up to find the frame_size is in principle still correct as it does
not exceed the 2048 bytes frame_size (which is max for ixgbe and i40e),
but the 32 bytes offset of pkt_data_start puts this over the 2048 bytes
limit. This cause skb_shared_info to spill into next frame. It is a little
hard to trigger, as the SKB need to use above 15 skb_shinfo->frags[] as
far as I calculate. This does happen in practise for TCP streams when
skb_try_coalesce() kicks in.
KASAN can be used to detect these wrong memory accesses, I've seen:
BUG: KASAN: use-after-free in skb_try_coalesce+0x3cb/0x760
BUG: KASAN: wild-memory-access in skb_release_data+0xe2/0x250
Driver veth also construct a SKB from xdp_frame in this way, but is not
affected, as it doesn't reserve/deduct the room (used by xdp_frame) from
the SKB headroom. Instead is clears the pointers via xdp_scrub_frame(),
and allows SKB to use this area.
The fix in this patch is to do like veth and instead allow SKB to (re)use
the area occupied by xdp_frame, by clearing via xdp_scrub_frame(). (This
does kill the idea of the SKB being able to access (mem) info from this
area, but I guess it was a bad idea anyhow, and it was already killed by
the veth changes.)
Fixes: 77ea5f4cbe ("bpf/cpumap: make sure frame_size for build_skb is aligned if headroom isn't")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa9ace68e ]
In dlpar_parse_cc_property(), 'prop->name' is allocated by kstrdup().
kstrdup() may return NULL, so it should be checked and handle error.
And prop should be freed if 'prop->name' is NULL.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 406dcbc55a ]
The LattePanda board has a sound card chtrt5645, when there is nothing
plugged in the headphone jack, the system thinks the headphone is
plugged in, while we plug a headphone in the jack, the system thinks
the headphone is unplugged.
If adding quirk=0x21 in the module parameter, the headphone jack can
work well. So let us fix it via platform_data.
https://bugs.launchpad.net/bugs/182459
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e69cf1fe2 ]
The the below commit, hns_roce_v2_modify_qp is called inside spinlock
while using GFP_KERNEL. Change it to GFP_ATOMIC.
Fixes: 0425e3e6e0 ("RDMA/hns: Support flush cqe for hip08 in kernel space")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab22bf0521 ]
The state of mr after reregister operation should be set to valid
state. Otherwise, it will keep the same as the state before reregistered.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d103905eb ]
In some application scenario, the user could not have receive queue when
run rdma write or read operation.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c6ccc035c ]
When flush cqe with srq, the driver disable to update the rq head pointer
into the hardware.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01929a65df ]
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c31b0c677 ]
When injecting 2 bit ECC error, it will cause fatal AXI interrupts. Before
the recovery of SAS controller reset, the internal of SAS controller is in
error. If CQ interrupts return at the time, actually it is exception CQ
interrupt, and it may cause resource release in disorder.
To avoid the exception situation, shutdown AXI bus after fatal AXI
interrupt. In SAS controller reset, it will restart AXI bus. For later
version of v3 hw, hardware will shutdown AXI bus for this situation, so
just fix current ver of v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ac234be1a ]
The ghes code is careful to parse and round firmware's advertised
memory requirements for CPER records, up to a maximum of 64K.
However when ghes_estatus_pool_expand() does its work, it splits
the requested size into PAGE_SIZE granules.
This means if firmware generates 5K of CPER records, and correctly
describes this in the table, __process_error() will silently fail as it
is unable to allocate more than PAGE_SIZE.
Switch the estatus pool to vmalloc() memory. On x86 vmalloc() memory
may fault and be fixed up by vmalloc_fault(). To prevent this call
vmalloc_sync_all() before an NMI handler could discover the memory.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78b0b690f6 ]
oops_begin() exists to group printk() messages with the oops message
printed by die(). To reach this caller we know that platform firmware
took this error first, then notified the OS via NMI with a 'panic'
severity.
Don't wait for another CPU to release the die-lock before panic()ing,
our only goal is to print this fatal error and panic().
This code is always called in_nmi(), and since commit 42a0bb3f71
("printk/nmi: generic solution for safe printk in NMI"), it has been
safe to call printk() from this context. Messages are batched in a
per-cpu buffer and printed via irq-work, or a call back from panic().
Link: https://patchwork.kernel.org/patch/10313555/
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cec9771d2e ]
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 201218e4d3 ]
Although the apparmorfs dentries are always dropped from the dentry cache
when the usage count drops to zero, there is no guarantee that this will
happen in aafs_remove(), as another thread might still be using it. In
this scenario, this means that the dentry will temporarily continue to
appear in the results of lookups, even after the call to aafs_remove().
In the case of removal of a profile - it also causes simple_rmdir()
on the profile directory to fail, as the directory won't be empty until
the usage counts of all child dentries have decreased to zero. This
results in the dentry for the profile directory leaking and appearing
empty in the file system tree forever.
Signed-off-by: Chris Coulson <chris.coulson@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6241e71e72 ]
HNS3 supports setting rx-usecs|tx-usecs as 0, but it will not
update dynamically when adaptive-tx or adaptive-rx is enable.
This patch removes the Redundant check.
Fixes: a95e1f8666 ("net: hns3: change the time interval of int_gl calculating")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed9535f9f ]
HNS3 VF driver support NIC and Roce, hdev stores NIC
handle and Roce handle, should use correct parameter for
container_of.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3ad430ac5 ]
The PFC enabling is based on user priority, currently it is
based on TC, which may cause PFC not setting correctly when pri
to TC mapping is not one to one relation.
This patch adds pfc_en in tm_info to fix it.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 352d20d611 ]
In bpf/syscall.c, map_create() first set map->usercnt to 1, a file
descriptor is supposed to return to userspace. When bpf_map_new_fd()
fails, drop the refcount.
Fixes: bd5f5f4ecb ("bpf: Add BPF_MAP_GET_FD_BY_ID")
Signed-off-by: Peng Sun <sironhide0null@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ed0579c12 ]
debugfs can now report an error code if something went wrong instead of
just NULL. So if the return value is to be used as a "real" dentry, it
needs to be checked if it is an error before dereferencing it.
This is now happening because of ff9fb72bc0 ("debugfs: return error
values, not NULL"). syzbot has found a way to trigger multiple debugfs
files attempting to be created, which fails, and then the error code
gets passed to dentry_path_raw() which obviously does not like it.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reported-and-tested-by: syzbot+7857962b4d45e602b8ad@syzkaller.appspotmail.com
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c53336c8f5 ]
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 781e62823c ]
In bpf/syscall.c, bpf_map_get_fd_by_id() use bpf_map_inc_not_zero()
to increase the refcount, both map->refcnt and map->usercnt. Then, if
bpf_map_new_fd() fails, should handle map->usercnt too.
Fixes: bd5f5f4ecb ("bpf: Add BPF_MAP_GET_FD_BY_ID")
Signed-off-by: Peng Sun <sironhide0null@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1f20c03f4 ]
hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.
Function sctp_transport_reset_hb_timer has two roles:
- initial start of hb_timer for a given transport,
- update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.
This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.
Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0; //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2; //or more
time_before(hb_timer.expire, new_expire) == false
Fixes: ba6f5e33bd ("sctp: avoid refreshing heartbeat timer too often")
Reported-by: Marcin Stojek <marcin.stojek@nokia.com>
Tested-by: Marcin Stojek <marcin.stojek@nokia.com>
Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 103d0244d2 ]
Report erspan version field to userspace in ip6gre_fill_info just for
erspan_v6 tunnels. Moreover report IFLA_GRE_ERSPAN_INDEX only for
erspan version 1.
The issue can be triggered with the following reproducer:
$ip link add name gre6 type ip6gre local 2001::1 remote 2002::2
$ip link set gre6 up
$ip -d link sh gre6
14: grep6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1448 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre6 2001::1 peer 2002::2 promiscuity 0 minmtu 0 maxmtu 0
ip6gre remote 2002::2 local 2001::1 hoplimit 64 encaplimit 4 tclass 0x00 flowlabel 0x00000 erspan_index 0 erspan_ver 0 addrgenmode eui64
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bdf700e53 ]
Report erspan version field to userspace in ipgre_fill_info just for
erspan tunnels. The issue can be triggered with the following reproducer:
$ip link add name gre1 type gre local 192.168.0.1 remote 192.168.1.1
$ip link set dev gre1 up
$ip -d link sh gre1
13: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre 192.168.0.1 peer 192.168.1.1 promiscuity 0 minmtu 0 maxmtu 0
gre remote 192.168.1.1 local 192.168.0.1 ttl inherit erspan_ver 0 addrgenmode eui64 numtxqueues 1 numrxqueues 1
Fixes: f551c91de2 ("net: erspan: introduce erspan v2 for ip_gre")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bf325a532 ]
With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.
They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7603ac1fc ]
Due to the depends on NET_UDP_TUNNEL, at the moment it is impossible to
compile GENEVE if no other protocol depending on NET_UDP_TUNNEL is
selected.
Fix this changing the depends to a select, and drop NET_IP_TUNNEL from the
select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-and-tested-by: Andrea Claudi <aclaudi@redhat.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c65285428b ]
The bitmap of found partitions in efx_ef10_mtd_probe was not
initialised, causing partitions to be suppressed based off whatever
value was in the bitmap at the start.
Fixes: 3366463513 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 323fb7b947 ]
Make sure i2s->rclk_srcrate is properly initialized also during
playback through the secondary DAI.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7384b538d3 ]
When we free skb at tipc_data_input, we return a 'false' boolean.
Then, skb passed to subcalling tipc_link_input in tipc_link_rcv,
<snip>
1303 int tipc_link_rcv:
...
1354 if (!tipc_data_input(l, skb, l->inputq))
1355 rc |= tipc_link_input(l, skb, l->inputq);
</snip>
Fix it by simple changing to a 'true' boolean when skb is being free-ed.
Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above
condition.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccc8ca9b90 ]
The recent change in the rx_curs_confirmed assignment disregards
byte order, which causes problems on little endian architectures.
This patch fixes it.
Fixes: b8649efad8 ("net/smc: fix sender_free computation") (net-tree)
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0803de7804 ]
Currently, blktrace will not show requests that don't have any data as
rq->__sector is initialized to -1 which is out of device range and thus
discarded by act_log_check(). This is most notably the case for cache
flush requests sent to the device. Fix the problem by making
blk_rq_trace_sector() return 0 for requests without initialized sector.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
