[ Upstream commit 66cce9e73e ]
When a remote usb device is attached to the local Virtual USB
Host Controller Root Hub port, the bound device driver may send
a port reset command.
vhci_hcd accepts port resets only when the device doesn't have
port address assigned to it. When reset happens device is in
assigned/used state and vhci_hcd rejects it leaving the port in
a stuck state.
This problem was found when a blue-tooth or xbox wireless dongle
was passed through using usbip.
A few drivers reset the port during probe including mt76 driver
specific to this bug report. Fix the problem with a change to
honor reset requests when device is in used state (VDEV_ST_USED).
Reported-and-tested-by: Michael <msbroadf@gmail.com>
Suggested-by: Michael <msbroadf@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210819225937.41037-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c75bde329 ]
If IRQ occurs between calling dsps_setup_optional_vbus_irq()
and dsps_create_musb_pdev(), then null pointer dereference occurs
since glue->musb wasn't initialized yet.
The patch puts initializing of neccesery data before registration
of the interrupt handler.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210819163323.17714-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2847c46c61 ]
This reverts commit 5d5323a6f3.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d72c74197b ]
smb_buf is allocated by small_smb_init_no_tc(), and buf type is
CIFS_SMALL_BUFFER, so we should use cifs_small_buf_release() to
release it in failed path.
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e72a55f2e5 ]
When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.
IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)
The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).
It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.
Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().
The test code and the output of only the CMD17 is included in the
commit to limit the message length.
CMD17 (Test Code Snippet):
==========================
printf("Forming CMD%d\n", opt_idx);
/* single block read */
cmd.blksz = 512;
cmd.blocks = 1;
cmd.write_flag = 0;
cmd.opcode = 17;
//cmd.arg = atoi(argv[3]);
cmd.arg = 0x09B2FFFF;
/* Expecting response R1B */
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
memset(data, 0, sizeof(__u8) * 512);
mmc_ioc_cmd_set_data(cmd, data);
printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
if(ioctl(fd, MMC_IOC_CMD, &cmd))
perror("Error");
printf("\nResponse: %08x\n", cmd.response[0]);
CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 00000000
(Incorrect response)
CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d82d73da3 ]
0Day robot observed that it's easily timeout on a heavy load host.
-------------------
# selftests: bpf: test_maps
# Fork 1024 tasks to 'test_update_delete'
# Fork 1024 tasks to 'test_update_delete'
# Fork 100 tasks to 'test_hashmap'
# Fork 100 tasks to 'test_hashmap_percpu'
# Fork 100 tasks to 'test_hashmap_sizes'
# Fork 100 tasks to 'test_hashmap_walk'
# Fork 100 tasks to 'test_arraymap'
# Fork 100 tasks to 'test_arraymap_percpu'
# Failed sockmap unexpected timeout
not ok 3 selftests: bpf: test_maps # exit=1
# selftests: bpf: test_lru_map
# nr_cpus:8
-------------------
Since this test will be scheduled by 0Day to a random host that could have
only a few cpus(2-8), enlarge the timeout to avoid a false NG report.
In practice, i tried to pin it to only one cpu by 'taskset 0x01 ./test_maps',
and knew 10S is likely enough, but i still perfer to a larger value 30.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210820015556.23276-2-lizhijian@cn.fujitsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac5e45291 ]
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6211e9cb2f ]
Trying to boot without SYSFS, but with OF_DYNAMIC quickly
results in a crash:
[ 0.088460] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
[...]
[ 0.103927] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.14.0-rc3 #4179
[ 0.105810] Hardware name: linux,dummy-virt (DT)
[ 0.107147] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 0.108876] pc : kernfs_find_and_get_ns+0x3c/0x7c
[ 0.110244] lr : kernfs_find_and_get_ns+0x3c/0x7c
[...]
[ 0.134087] Call trace:
[ 0.134800] kernfs_find_and_get_ns+0x3c/0x7c
[ 0.136054] safe_name+0x4c/0xd0
[ 0.136994] __of_attach_node_sysfs+0xf8/0x124
[ 0.138287] of_core_init+0x90/0xfc
[ 0.139296] driver_init+0x30/0x4c
[ 0.140283] kernel_init_freeable+0x160/0x1b8
[ 0.141543] kernel_init+0x30/0x140
[ 0.142561] ret_from_fork+0x10/0x18
While not having sysfs isn't a very common option these days,
it is still expected that such configuration would work.
Paper over it by bailing out from __of_attach_node_sysfs() if
CONFIG_SYSFS isn't enabled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210820144722.169226-1-maz@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3736127a3a ]
Function btrfs_lookup_data_extent calls btrfs_search_slot to verify if
the EXTENT_ITEM exists in the extent tree. btrfs_search_slot can return
values bellow zero if an error happened.
Function replay_one_extent currently checks if the search found
something (0 returned) and increments the reference, and if not, it
seems to evaluate as 'not found'.
Fix the condition by checking if the value was bellow zero and return
early.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db87db65c1 ]
> Hi Arnd,
>
> First bad commit (maybe != root cause):
>
> tree: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git master
> head: 2f73937c9aa561e2082839bc1a8efaac75d6e244
> commit: 47fd22f2b8 [4771/5318] cs89x0: rework driver configuration
> config: m68k-randconfig-c003-20210804 (attached as .config)
> compiler: m68k-linux-gcc (GCC) 10.3.0
> reproduce (this is a W=1 build):
> wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=47fd22f2b84765a2f7e3f150282497b902624547
> git remote add linux-next https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
> git fetch --no-tags linux-next master
> git checkout 47fd22f2b8
> # save the attached .config to linux build tree
> COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-10.3.0 make.cross ARCH=m68k
>
> If you fix the issue, kindly add following tag as appropriate
> Reported-by: kernel test robot <lkp@intel.com>
>
> All errors (new ones prefixed by >>):
>
> In file included from include/linux/kernel.h:19,
> from include/linux/list.h:9,
> from include/linux/module.h:12,
> from drivers/net/ethernet/cirrus/cs89x0.c:51:
> drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
> drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
> 897 | (unsigned long)isa_virt_to_bus(lp->dma_buff));
> | ^~~~~~~~~~~~~~~
> include/linux/printk.h:141:17: note: in definition of macro 'no_printk'
> 141 | printk(fmt, ##__VA_ARGS__); \
> | ^~~~~~~~~~~
> drivers/net/ethernet/cirrus/cs89x0.c:86:3: note: in expansion of macro 'pr_debug'
> 86 | pr_##level(fmt, ##__VA_ARGS__); \
> | ^~~
> drivers/net/ethernet/cirrus/cs89x0.c:894:3: note: in expansion of macro 'cs89_dbg'
> 894 | cs89_dbg(1, debug, "%s: dma %lx %lx\n",
> | ^~~~~~~~
> >> drivers/net/ethernet/cirrus/cs89x0.c:914:3: error: implicit declaration of function 'disable_dma'; did you mean 'disable_irq'? [-Werror=implicit-function-declaration]
As far as I can tell, this is a bug with the m68kmmu architecture, not
with my driver:
The CONFIG_ISA_DMA_API option is provided for coldfire, which implements it,
but dragonball also sets the option as a side-effect, without actually
implementing
the interfaces. The patch below should fix it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8fb4df1f5 ]
'bp_ena' in Aura context is NIX block index, setting it
zero will always backpressure NIX0 block, even if NIXLF
belongs to NIX1. Hence fix this by setting it appropriately
based on NIX block address.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05e4588738 ]
The kernel test robot reports undefined reference after we report wakeup
reason to mac80211. This is because CONFIG_PM is not defined in the testing
configuration file. In fact, functions within wow.c are used if CONFIG_PM
is defined, so use CONFIG_PM to decide whether we build this file or not.
The reported messages are:
hppa-linux-ld: drivers/net/wireless/realtek/rtw88/wow.o: in function `rtw_wow_show_wakeup_reason':
>> (.text+0x6c4): undefined reference to `ieee80211_report_wowlan_wakeup'
>> hppa-linux-ld: (.text+0x6e0): undefined reference to `ieee80211_report_wowlan_wakeup'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-4-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02a55c0009 ]
In current wow flow, driver calls rtw_wow_fw_start and sleep for 100ms,
to wait firmware finish preliminary work and then update the value of
WOWLAN_WAKE_REASON register to zero. But later firmware will start wow
function with power-saving mode, in which mode the value of
WOWLAN_WAKE_REASON register is 0xea. So driver may get 0xea value and
return fail. We use read_poll_timeout instead to check the value to avoid
this issue.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c626f3864b ]
In certain randconfigs, clang warns:
drivers/gpu/drm/exynos/exynos_drm_dma.c:121:19: warning: variable
'mapping' is uninitialized when used here [-Wuninitialized]
priv->mapping = mapping;
^~~~~~~
drivers/gpu/drm/exynos/exynos_drm_dma.c:111:16: note: initialize the
variable 'mapping' to silence this warning
void *mapping;
^
= NULL
1 warning generated.
This occurs when CONFIG_EXYNOS_IOMMU is enabled and both
CONFIG_ARM_DMA_USE_IOMMU and CONFIG_IOMMU_DMA are disabled, which makes
the code look like
void *mapping;
if (0)
mapping = arm_iommu_create_mapping()
else if (0)
mapping = iommu_get_domain_for_dev()
...
priv->mapping = mapping;
Add an else branch that initializes mapping to the -ENODEV error pointer
so that there is no more warning and the driver does not change during
runtime.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de875b231 ]
Locks have two sets of op arrays, fl_lmops for the lock manager (lockd
or nfsd), fl_ops for the filesystem. The server-side lockd code has
been setting its own fl_ops, which leads to confusion (and crashes) in
the reexport case, where the filesystem expects to be the only one
setting fl_ops.
And there's no reason for it that I can see-the lm_get/put_owner ops do
the same job.
Reported-by: Daire Byrne <daire@dneg.com>
Tested-by: Daire Byrne <daire@dneg.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1340f80f0 ]
In the gfs2 withdraw sequence, the dlm protocol is unmounted with a call
to lm_unmount. After a withdraw, users are allowed to unmount the
withdrawn file system. But at that point we may still have glocks left
over that we need to free via unmount's call to gfs2_gl_hash_clear.
These glocks may have never been completed because of whatever problem
caused the withdraw (IO errors or whatever).
Before this patch, function gdlm_put_lock would still try to call into
dlm to unlock these leftover glocks, which resulted in dlm returning
-EINVAL because the lock space was abandoned. These glocks were never
freed because there was no mechanism after that to free them.
This patch adds a check to gdlm_put_lock to see if the locking protocol
was inactive (DFL_UNMOUNT flag) and if so, free the glock and not
make the invalid call into dlm.
I could have combined this "if" with the one that follows, related to
leftover glock LVBs, but I felt the code was more readable with its own
if clause.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83e5dcbece ]
When skipping the tests due to a lack of system support for MTE we
currently print a message saying FAIL which makes it look like the test
failed even though the test did actually report KSFT_SKIP, creating some
confusion. Change the error message to say SKIP instead so things are
clearer.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210819172902.56211-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74fc4f8287 ]
Currently, when creating an ingress qdisc on an indirect device before
the driver registered for callbacks, the driver will not have a chance
to register its filter configuration callbacks.
To fix that, modify the code such that it keeps track of all the ingress
qdiscs that call flow_indr_dev_setup_offload(). When a driver calls
flow_indr_dev_register(), go through the list of tracked ingress qdiscs
and call the driver callback entry point so as to give it a chance to
register its callback.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe34165cc ]
Fix buf allocation size (it needs to be 2 bytes larger). Found when
__alloc_size() annotations were added to kmalloc() interfaces.
In file included from ./include/linux/string.h:253,
from ./include/linux/bitmap.h:10,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/paravirt.h:17,
from ./arch/x86/include/asm/irqflags.h:63,
from ./include/linux/irqflags.h:16,
from ./include/linux/rcupdate.h:26,
from ./include/linux/rculist.h:11,
from ./include/linux/pid.h:5,
from ./include/linux/sched.h:14,
from ./include/linux/blkdev.h:5,
from drivers/staging/rts5208/rtsx_scsi.c:12:
In function 'get_ms_information',
inlined from 'ms_sp_cmnd' at drivers/staging/rts5208/rtsx_scsi.c:2877:12,
inlined from 'rtsx_scsi_handler' at drivers/staging/rts5208/rtsx_scsi.c:3247:12:
./include/linux/fortify-string.h:54:29: warning: '__builtin_memcpy' forming offset [106, 107] is out
of the bounds [0, 106] [-Warray-bounds]
54 | #define __underlying_memcpy __builtin_memcpy
| ^
./include/linux/fortify-string.h:417:2: note: in expansion of macro '__underlying_memcpy'
417 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
./include/linux/fortify-string.h:463:26: note: in expansion of macro '__fortify_memcpy_chk'
463 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/staging/rts5208/rtsx_scsi.c:2851:3: note: in expansion of macro 'memcpy'
2851 | memcpy(buf + i, ms_card->raw_sys_info, 96);
| ^~~~~~
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-staging@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818044252.1533634-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b16ac5bf73 ]
libbpf CI has reported send_signal test is flaky although
I am not able to reproduce it in my local environment.
But I am able to reproduce with on-demand libbpf CI ([1]).
Through code analysis, the following is possible reason.
The failed subtest runs bpf program in softirq environment.
Since bpf_send_signal() only sends to a fork of "test_progs"
process. If the underlying current task is
not "test_progs", bpf_send_signal() will not be triggered
and the subtest will fail.
To reduce the chances where the underlying process is not
the intended one, this patch boosted scheduling priority to
-20 (highest allowed by setpriority() call). And I did
10 runs with on-demand libbpf CI with this patch and I
didn't observe any failures.
[1] https://github.com/libbpf/libbpf/actions/workflows/ondemand.yml
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210817190923.3186725-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3faa49bce ]
Since the original TFO server code was implemented in commit
168a8f5805 ("tcp: TCP Fast Open Server -
main code path") the TFO server code has supported the sysctl bit flag
TFO_SERVER_COOKIE_NOT_REQD. Currently, when the TFO_SERVER_ENABLE and
TFO_SERVER_COOKIE_NOT_REQD sysctl bit flags are set, a server connection
will accept a SYN with N bytes of data (N > 0) that has no TFO cookie,
create a new fast open connection, process the incoming data in the SYN,
and make the connection ready for accepting. After accepting, the
connection is ready for read()/recvmsg() to read the N bytes of data in
the SYN, ready for write()/sendmsg() calls and data transmissions to
transmit data.
This commit changes an edge case in this feature by changing this
behavior to apply to (N >= 0) bytes of data in the SYN rather than only
(N > 0) bytes of data in the SYN. Now, a server will accept a data-less
SYN without a TFO cookie if TFO_SERVER_COOKIE_NOT_REQD is set.
Caveat! While this enables a new kind of TFO (data-less empty-cookie
SYN), some firewall rules setup may not work if they assume such packets
are not legit TFOs and will filter them.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210816205105.2533289-1-luke.w.hsiao@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b69eea82d3 ]
Modern-day mapping_set_error has the ability to squash the usual
negative error code into something appropriate for long-term storage in
a struct address_space -- ENOSPC becomes AS_ENOSPC, and everything else
becomes EIO. iomap squashes /everything/ to EIO, just as XFS did before
that, but this doesn't make sense.
Fix this by making it so that we can pass ENOSPC to userspace when
writeback fails due to space problems.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b8061bad ]
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 020d86fc0d ]
The 'required-opps' property is considered optional, hence remove
the pr_err() in of_parse_required_opp() when we find the property is
missing.
While at it, also fix the return value of
of_get_required_opp_performance_state() when of_parse_required_opp()
fails, return a -ENODEV instead of the -EINVAL.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cafae4cd62 ]
LE Enhanced Connection Complete contains the Local RPA used in the
connection which must be used when set otherwise there could problems
when pairing since the address used by the remote stack could be the
Local RPA:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 4, Part E
page 2396
'Resolvable Private Address being used by the local device for this
connection. This is only valid when the Own_Address_Type (from the
HCI_LE_Create_Connection, HCI_LE_Set_Advertising_Parameters,
HCI_LE_Set_Extended_Advertising_Parameters, or
HCI_LE_Extended_Create_Connection commands) is set to 0x02 or
0x03, and the Controller generated a resolvable private address for the
local device using a non-zero local IRK. For other Own_Address_Type
values, the Controller shall return all zeros.'
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7006de6c2 ]
We cannot detect a (perhaps buggy) controller that is sending us
a completion for a request that was already completed (for example
sending a completion twice), this phenomenon was seen in the wild
a few times.
So to protect against this, we use the upper 4 msbits of the nvme sqe
command_id to use as a 4-bit generation counter and verify it matches
the existing request generation that is incrementing on every execution.
The 16-bit command_id structure now is constructed by:
| xxxx | xxxxxxxxxxxx |
gen request tag
This means that we are giving up some possible queue depth as 12 bits
allow for a maximum queue depth of 4095 instead of 65536, however we
never create such long queues anyways so no real harm done.
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b01a9d0ca ]
We already validate it when receiving the c2hdata pdu header
and this is not changing so this is a redundant check.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f865d0292f ]
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70e740ad55 ]
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79f5962bae ]
The maximum MTU was set to 2304, which is the maximum MSDU size. While
this is valid for normal WLAN interfaces, it is too low for monitor
interfaces. A monitor interface may receive and inject MPDU frames, and
the maximum MPDU frame size is larger than 2304. The MPDU may also
contain an A-MSDU frame, in which case the size may be much larger than
the MTU limit. Since the maximum size of an A-MSDU depends on the PHY
mode of the transmitting STA, it is not possible to set an exact MTU
limit for a monitor interface. Now the maximum MTU for a monitor
interface is unrestricted.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210628123246.2070558-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554594567b ]
The variable dc->clk_mgr is checked in:
if (dc->clk_mgr && dc->clk_mgr->funcs->get_clock)
This indicates dc->clk_mgr can be NULL.
However, it is dereferenced in:
if (!dc->clk_mgr->funcs->get_clock)
To fix this null-pointer dereference, check dc->clk_mgr and the function
pointer dc->clk_mgr->funcs->get_clock earlier, and return if one of them
is NULL.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a211260c34 ]
The variable val is declared without initialization, and its address is
passed to amdgpu_i2c_get_byte(). In this function, the value of val is
accessed in:
DRM_DEBUG("i2c 0x%02x 0x%02x read failed\n",
addr, *val);
Also, when amdgpu_i2c_get_byte() returns, val may remain uninitialized,
but it is accessed in:
val &= ~amdgpu_connector->router.ddc_mux_control_pin;
To fix this possible uninitialized-variable access, initialize val to 0 in
amdgpu_i2c_router_select_ddc_port().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 979aa51967 ]
Fix the following smatch warning:
wait_func_handle_exec_timeout() warn: should '1 << ent->idx' be a 64 bit type?
Use 1ULL, to have a 64 bit type variable.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
