[ Upstream commit f30d4968e9 ]
Below is a simplified case from a report in bcc [0]:
r4 = 20
*(u32 *)(r10 -4) = r4
*(u32 *)(r10 -8) = r4 /* r4 state is tracked */
r4 = *(u64 *)(r10 -8) /* Read more than the tracked 32bit scalar.
* verifier rejects as 'corrupted spill memory'.
*/
After commit 354e8f1970 ("bpf: Support <8-byte scalar spill and refill"),
the 8-byte aligned 32bit spill is also tracked by the verifier and the
register state is stored.
However, if 8 bytes are read from the stack instead of the tracked 4 byte
scalar, then verifier currently rejects the program as "corrupted spill
memory". This patch fixes this case by allowing it to read but marks the
register as unknown.
Also note that, if the prog is trying to corrupt/leak an earlier spilled
pointer by spilling another <8 bytes register on top, this has already
been rejected in the check_stack_write_fixed_off().
[0] https://github.com/iovisor/bcc/pull/3683
Fixes: 354e8f1970 ("bpf: Support <8-byte scalar spill and refill")
Reported-by: Hengqi Chen <hengqi.chen@gmail.com>
Reported-by: Yonghong Song <yhs@gmail.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Hengqi Chen <hengqi.chen@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20211102064535.316018-1-kafai@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6c052afe6 ]
Wp-gpios property can be used on NVMEM nodes and the same property can
be also used on MTD NAND nodes. In case of the wp-gpios property is
defined at NAND level node, the GPIO management is done at NAND driver
level. Write protect is disabled when the driver is probed or resumed
and is enabled when the driver is released or suspended.
When no partitions are defined in the NAND DT node, then the NAND DT node
will be passed to NVMEM framework. If wp-gpios property is defined in
this node, the GPIO resource is taken twice and the NAND controller
driver fails to probe.
It would be possible to set config->wp_gpio at MTD level before calling
nvmem_register function but NVMEM framework will toggle this GPIO on
each write when this GPIO should only be controlled at NAND level driver
to ensure that the Write Protect has not been enabled.
A way to fix this conflict is to add a new boolean flag in nvmem_config
named ignore_wp. In case ignore_wp is set, the GPIO resource will
be managed by the provider.
Fixes: 2a127da461 ("nvmem: add support for the write-protect pin")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220220151432.16605-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ab3428cfd9 ("nvmem: core: fix registration vs use race")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4920ab131b upstream.
This patch fixes slab-out-of-bounds reads in brcmfmac that occur in
brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count
value of channel specifications provided by the device is greater than
the length of 'list->element[]', decided by the size of the 'list'
allocated with kzalloc(). The patch adds checks that make the functions
free the buffer and return -EINVAL if that is the case. Note that the
negative return is handled by the caller, brcmf_setup_wiphybands() or
brcmf_cfg80211_attach().
Found by a modified version of syzkaller.
Crash Report from brcmf_construct_chaninfo():
==================================================================
BUG: KASAN: slab-out-of-bounds in brcmf_setup_wiphybands+0x1238/0x1430
Read of size 4 at addr ffff888115f24600 by task kworker/0:2/1896
CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
dump_stack_lvl+0x57/0x7d
print_address_description.constprop.0.cold+0x93/0x334
kasan_report.cold+0x83/0xdf
brcmf_setup_wiphybands+0x1238/0x1430
brcmf_cfg80211_attach+0x2118/0x3fd0
brcmf_attach+0x389/0xd40
brcmf_usb_probe+0x12de/0x1690
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_set_configuration+0x984/0x1770
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_new_device.cold+0x463/0xf66
hub_event+0x10d5/0x3330
process_one_work+0x873/0x13e0
worker_thread+0x8b/0xd10
kthread+0x379/0x450
ret_from_fork+0x1f/0x30
Allocated by task 1896:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
kmem_cache_alloc_trace+0x19e/0x330
brcmf_setup_wiphybands+0x290/0x1430
brcmf_cfg80211_attach+0x2118/0x3fd0
brcmf_attach+0x389/0xd40
brcmf_usb_probe+0x12de/0x1690
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_set_configuration+0x984/0x1770
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_new_device.cold+0x463/0xf66
hub_event+0x10d5/0x3330
process_one_work+0x873/0x13e0
worker_thread+0x8b/0xd10
kthread+0x379/0x450
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff888115f24000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1536 bytes inside of
2048-byte region [ffff888115f24000, ffff888115f24800)
Memory state around the buggy address:
ffff888115f24500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888115f24580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff888115f24600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888115f24680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888115f24700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Crash Report from brcmf_enable_bw40_2g():
==================================================================
BUG: KASAN: slab-out-of-bounds in brcmf_cfg80211_attach+0x3d11/0x3fd0
Read of size 4 at addr ffff888103787600 by task kworker/0:2/1896
CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
dump_stack_lvl+0x57/0x7d
print_address_description.constprop.0.cold+0x93/0x334
kasan_report.cold+0x83/0xdf
brcmf_cfg80211_attach+0x3d11/0x3fd0
brcmf_attach+0x389/0xd40
brcmf_usb_probe+0x12de/0x1690
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_set_configuration+0x984/0x1770
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_new_device.cold+0x463/0xf66
hub_event+0x10d5/0x3330
process_one_work+0x873/0x13e0
worker_thread+0x8b/0xd10
kthread+0x379/0x450
ret_from_fork+0x1f/0x30
Allocated by task 1896:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
kmem_cache_alloc_trace+0x19e/0x330
brcmf_cfg80211_attach+0x3302/0x3fd0
brcmf_attach+0x389/0xd40
brcmf_usb_probe+0x12de/0x1690
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_set_configuration+0x984/0x1770
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_new_device.cold+0x463/0xf66
hub_event+0x10d5/0x3330
process_one_work+0x873/0x13e0
worker_thread+0x8b/0xd10
kthread+0x379/0x450
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff888103787000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1536 bytes inside of
2048-byte region [ffff888103787000, ffff888103787800)
Memory state around the buggy address:
ffff888103787500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888103787580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff888103787600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888103787680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888103787700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Reported-by: Dokyung Song <dokyungs@yonsei.ac.kr>
Reported-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr>
Reported-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221116142952.518241-1-linuxlovemin@yonsei.ac.kr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57e9af7831 upstream.
As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
CPU0 CPU1
dma_rx_complete()
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma_flush()
__dma_rx_complete()
dma->rx_running = 0
// Complete DMA Rx
spin_unlock_irqrestore(&port->lock)
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma()
dma->rx_running = 1
// Setup a new DMA Rx
spin_unlock_irqrestore(&port->lock)
spin_lock_irqsave(&port->lock)
// sees dma->rx_running = 1
__dma_rx_complete()
dma->rx_running = 0
// Incorrectly complete
// running DMA Rx
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f65c4bbbd6 upstream.
A Sysbot [1] corrupted filesystem exposes two flaws in the handling and
sanity checking of the xattr_ids count in the filesystem. Both of these
flaws cause computation overflow due to incorrect typing.
In the corrupted filesystem the xattr_ids value is 4294967071, which
stored in a signed variable becomes the negative number -225.
Flaw 1 (64-bit systems only):
The signed integer xattr_ids variable causes sign extension.
This causes variable overflow in the SQUASHFS_XATTR_*(A) macros. The
variable is first multiplied by sizeof(struct squashfs_xattr_id) where the
type of the sizeof operator is "unsigned long".
On a 64-bit system this is 64-bits in size, and causes the negative number
to be sign extended and widened to 64-bits and then become unsigned. This
produces the very large number 18446744073709548016 or 2^64 - 3600. This
number when rounded up by SQUASHFS_METADATA_SIZE - 1 (8191 bytes) and
divided by SQUASHFS_METADATA_SIZE overflows and produces a length of 0
(stored in len).
Flaw 2 (32-bit systems only):
On a 32-bit system the integer variable is not widened by the unsigned
long type of the sizeof operator (32-bits), and the signedness of the
variable has no effect due it always being treated as unsigned.
The above corrupted xattr_ids value of 4294967071, when multiplied
overflows and produces the number 4294963696 or 2^32 - 3400. This number
when rounded up by SQUASHFS_METADATA_SIZE - 1 (8191 bytes) and divided by
SQUASHFS_METADATA_SIZE overflows again and produces a length of 0.
The effect of the 0 length computation:
In conjunction with the corrupted xattr_ids field, the filesystem also has
a corrupted xattr_table_start value, where it matches the end of
filesystem value of 850.
This causes the following sanity check code to fail because the
incorrectly computed len of 0 matches the incorrect size of the table
reported by the superblock (0 bytes).
len = SQUASHFS_XATTR_BLOCK_BYTES(*xattr_ids);
indexes = SQUASHFS_XATTR_BLOCKS(*xattr_ids);
/*
* The computed size of the index table (len bytes) should exactly
* match the table start and end points
*/
start = table_start + sizeof(*id_table);
end = msblk->bytes_used;
if (len != (end - start))
return ERR_PTR(-EINVAL);
Changing the xattr_ids variable to be "usigned int" fixes the flaw on a
64-bit system. This relies on the fact the computation is widened by the
unsigned long type of the sizeof operator.
Casting the variable to u64 in the above macro fixes this flaw on a 32-bit
system.
It also means 64-bit systems do not implicitly rely on the type of the
sizeof operator to widen the computation.
[1] https://lore.kernel.org/lkml/000000000000cd44f005f1a0f17f@google.com/
Link: https://lkml.kernel.org/r/20230127061842.10965-1-phillip@squashfs.org.uk
Fixes: 506220d2ba ("squashfs: add more sanity checks in xattr id lookup")
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: <syzbot+082fa4af80a5bb1a9843@syzkaller.appspotmail.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Fedor Pchelkin <pchelkin@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d2c7203ff upstream.
In kernels compiled with CONFIG_PARAVIRT=n, the compiler re-orders the
DR7 read in exc_nmi() to happen before the call to sev_es_ist_enter().
This is problematic when running as an SEV-ES guest because in this
environment the DR7 read might cause a #VC exception, and taking #VC
exceptions is not safe in exc_nmi() before sev_es_ist_enter() has run.
The result is stack recursion if the NMI was caused on the #VC IST
stack, because a subsequent #VC exception in the NMI handler will
overwrite the stack frame of the interrupted #VC handler.
As there are no compiler barriers affecting the ordering of DR7
reads/writes, make the accesses to this register volatile, forbidding
the compiler to re-order them.
[ bp: Massage text, make them volatile too, to make sure some
aggressive compiler optimization pass doesn't discard them. ]
Fixes: 315562c9af ("x86/sev-es: Adjust #VC IST Stack on entering NMI handler")
Reported-by: Alexey Kardashevskiy <aik@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230127035616.508966-1-aik@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3489dbb696 upstream.
Patch series "Fixes for hugetlb mapcount at most 1 for shared PMDs".
This issue of mapcount in hugetlb pages referenced by shared PMDs was
discussed in [1]. The following two patches address user visible behavior
caused by this issue.
[1] https://lore.kernel.org/linux-mm/Y9BF+OCdWnCSilEu@monkey/
This patch (of 2):
A hugetlb page will have a mapcount of 1 if mapped by multiple processes
via a shared PMD. This is because only the first process increases the
map count, and subsequent processes just add the shared PMD page to their
page table.
page_mapcount is being used to decide if a hugetlb page is shared or
private in /proc/PID/smaps. Pages referenced via a shared PMD were
incorrectly being counted as private.
To fix, check for a shared PMD if mapcount is 1. If a shared PMD is found
count the hugetlb page as shared. A new helper to check for a shared PMD
is added.
[akpm@linux-foundation.org: simplification, per David]
[akpm@linux-foundation.org: hugetlb.h: include page_ref.h for page_count()]
Link: https://lkml.kernel.org/r/20230126222721.222195-2-mike.kravetz@oracle.com
Fixes: 25ee01a2fc ("mm: hugetlb: proc: add hugetlb-related fields to /proc/PID/smaps")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: James Houghton <jthoughton@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev>
Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f394c0e7d upstream.
GCC 13 will enable -fasynchronous-unwind-tables by default on riscv. In
the kernel, we don't have any use for unwind tables yet, so disable them.
More importantly, the .eh_frame section brings relocations
(R_RISC_32_PCREL, R_RISCV_SET{6,8,16}, R_RISCV_SUB{6,8,16}) into modules
that we are not prepared to handle.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Link: https://lore.kernel.org/r/mvmzg9xybqu.fsf@suse.de
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2acd031347 upstream.
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a53f945879 upstream.
ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
14-bit left-justified sample data and MAGN output data registers
contain the X-axis, Y-axis, and Z-axis 16-bit sample data. The ACCEL
raw register output data should be divided by 4 before sent to
userspace.
Apply a 2 bits signed right shift to the raw data from ACCEL output
data register but keep that from MAGN sensor as the origin.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 636ab417a7 upstream.
UEFI v2.10 introduces version 2 of the memory attributes table, which
turns the reserved field into a flags field, but is compatible with
version 1 in all other respects. So let's not complain about version 2
if we encounter it.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32e40f9506 upstream.
The DIAG 288 statement consumes an EBCDIC string the address of which is
passed in a register. Use a "memory" clobber to tell the compiler that
memory is accessed within the inline assembly.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe8973a3ad upstream.
With CONFIG_VMAP_STACK=y the stack is allocated from the vmalloc space.
Data passed to a hardware or a hypervisor interface that
requires V=R can no longer be allocated on the stack.
Use kmalloc() to get memory for a diag288 command.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a6a87c3616 ]
A lot of modern Clevo barebones have touchpad and/or keyboard issues after
suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of them
have an external PS/2 port so this can safely be set for all of them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use. No negative effects could be
observed when setting all four.
The list is quite massive as neither the TUXEDO nor the Clevo dmi strings
have been very consistent historically. I tried to keep the list as short
as possible without risking on missing an affected device.
This is revision 3. The Clevo N150CU barebone is still removed as it might
have problems with the fix and needs further investigations. The
SchenkerTechnologiesGmbH System-/Board-Vendor string variations are
added. This is now based in the quirk table refactor. This now also
includes the additional noaux flag for the NS7xMU.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-5-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff946268a0 ]
Merge i8042 quirk tables to reduce code duplication for devices that need
more than one quirk. Before every quirk had its own table with devices
needing that quirk. If a new quirk needed to be added a new table had to
be created. When a device needed multiple quirks, it appeared in multiple
tables. Now only one table called i8042_dmi_quirk_table exists. In it every
device has one entry and required quirks are coded in the .driver_data
field of the struct dmi_system_id used by this table. Multiple quirks for
one device can be applied by bitwise-or of the new SERIO_QUIRK_* defines.
Also align quirkable options with command line parameters and make vendor
wide quirks per device overwriteable on a per device basis. The first match
is honored while following matches are ignored. So when a vendor wide quirk
is defined in the table, a device can inserted before and therefore
ignoring the vendor wide define.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220629112725.12922-3-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 921deb9da1 ]
__ffs_ep0_queue_wait executes holding the spinlock of &ffs->ev.waitq.lock
and unlocks it after the assignments to usb_request are done.
However in the code if the request is already NULL we bail out returning
-EINVAL but never unlocked the spinlock.
Fix this by adding spin_unlock_irq &ffs->ev.waitq.lock before returning.
Fixes: 6a19da1110 ("usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait")
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/20230124091149.18647-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2b0b5210f ]
When listen() and accept() are called on an x25 socket
that connect() succeeds, accept() succeeds immediately.
This is because x25_connect() queues the skb to
sk->sk_receive_queue, and x25_accept() dequeues it.
This creates a child socket with the sk of the parent
x25 socket, which can cause confusion.
Fix x25_listen() to return -EINVAL if the socket has
already been successfully connect()ed to avoid this issue.
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
