During driver unload/reload testing, the NVMe initiator would not
re-establish connectivity to NVMe controllers on reload.
The failing NVMe array supports concurrent FCP and NVMe operation via
different nport_id's. The array was repeatedly sending an ADISC every 2
seconds after PLOGI completed and while NVMe subsystems were executing
discovery. The target would continue this state for roughly 45 seconds.
The driver's current behavior on ADISC receipt is to validate a the ADISC
vs the device and issue a RESUME_RPI to restore transmission. The receipt
of the ADISC effectively caused a driver to take actions similar to a
logout and login for the remote port, causing the deregistration of the
nvme rport and a subsequent re-registration. This caused a constant reset
and re-connect of the NVMe controller while this 45s window occurred. There
was no need for the state changes as ADISC does not change login state.
This patch corrects this behavior by validating if the remoteport is
already logged in (MAPPED) and when true, avoids the call to set the ndlp
state to MAPPED, which triggers the unreg/re-reg. Thus ADISC does not
change the login state of the node.
Link: https://lore.kernel.org/r/20200630215001.70793-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity reported the following error:
Assigned value that is never used may represent unnecessary computation.
The rc variable was initially assigned a value but in several cases, when
an error case is detected, it is reassigned a new value. The initial value
had little use.
In code-reviewing this routine, it could use some cleanup:
- Setting the initialization value to -ENODEV is a much better choice and
lessens code in the routine.
- The wasn't tracking logic errors vs no error and mailbox failure.
Better to resolve by adding a status to track the mailbox failure
and merge it with the logic error when the routine returns.
Link: https://lore.kernel.org/r/20200630215001.70793-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The request_t 'handle' member is 32-bits wide, hence use wrt_reg_dword().
Change the cast in the wrt_reg_byte() call to make it clear that a regular
pointer is casted to an __iomem pointer.
Note: 'pkt' points to I/O memory for the qlafx00 adapter family and to
coherent memory for all other adapter families.
This patch fixes the following Coverity complaint:
CID 358864 (#1 of 1): Reliance on integer endianness (INCOMPATIBLE_CAST)
incompatible_cast: Pointer &pkt->handle points to an object whose effective
type is unsigned int (32 bits, unsigned) but is dereferenced as a narrower
unsigned short (16 bits, unsigned). This may lead to unexpected results
depending on machine endianness.
Link: https://lore.kernel.org/r/20200629225454.22863-7-bvanassche@acm.org
Fixes: 8ae6d9c7eb ("[SCSI] qla2xxx: Enhancements to support ISPFx00.")
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If tcmu_handle_completions() has to process a padding shorter than
sizeof(struct tcmu_cmd_entry), the current call to
tcmu_flush_dcache_range() with sizeof(struct tcmu_cmd_entry) as length
param is wrong and causes crashes on e.g. ARM, because
tcmu_flush_dcache_range() in this case calls
flush_dcache_page(vmalloc_to_page(start)); with start being an invalid
address above the end of the vmalloc'ed area.
The fix is to use the minimum of remaining ring space and sizeof(struct
tcmu_cmd_entry) as the length param.
The patch was tested on kernel 4.19.118.
See https://bugzilla.kernel.org/show_bug.cgi?id=208045#c10
Link: https://lore.kernel.org/r/20200629093756.8947-1-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow Exynos UFS driver to build as a module. This patch fixes the
followin build issue reported by kernel build robot.
drivers/scsi/ufs/ufs-exynos.o: in function `exynos_ufs_probe':
drivers/scsi/ufs/ufs-exynos.c:1231: undefined reference to `ufshcd_pltfrm_init'
drivers/scsi/ufs/ufs-exynos.o: in function `exynos_ufs_pre_pwr_mode':
drivers/scsi/ufs/ufs-exynos.c:635: undefined reference to `ufshcd_get_pwr_dev_param'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_shutdown'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_suspend'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_resume'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_suspend'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_resume'
drivers/scsi/ufs/ufs-exynos.o:undefined reference to `ufshcd_pltfrm_runtime_idle'
Link: https://lore.kernel.org/r/20200620173232.52521-1-alim.akhtar@samsung.com
Fixes: 55f4b1f736 ("scsi: ufs: ufs-exynos: Add UFS host support for Exynos SoCs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(scatter|gather)_data_area() need to flush dcache after writing data to or
before reading data from a page in uio data area. The two routines are
able to handle data transfer to/from such a page in fragments and flush the
cache after each fragment was copied by calling the wrapper
tcmu_flush_dcache_range().
That means:
1) flush_dcache_page() can be called multiple times for the same page.
2) Calling flush_dcache_page() indirectly using the wrapper does not make
sense, because each call of the wrapper is for one single page only and
the calling routine already has the correct page pointer.
Change (scatter|gather)_data_area() such that, instead of calling
tcmu_flush_dcache_range() before/after each memcpy, it now calls
flush_dcache_page() before unmapping a page (when writing is complete for
that page) or after mapping a page (when starting to read the page).
After this change only calls to tcmu_flush_dcache_range() for addresses in
vmalloc'ed command ring are left over.
The patch was tested on ARM with kernel 4.19.118 and 5.7.2
Link: https://lore.kernel.org/r/20200618131632.32748-2-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Tested-by: Daniel Meyerholt <dxm523@gmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS load calculation is based on "total_time" and "busy_time" in a
devfreq window. However, the source of time is different for both
parameters: "busy_time" is assigned from "jiffies" thus has different
accuracy from "total_time" which is assigned from ktime_get().
In addition, the time of window boundary is not exactly the same as the
starting busy time in this window if UFS is actually busy in the beginning
of the window. A similar accuracy error may also happen for the end of busy
time in current window.
To guarantee the precision of load calculation, we need to
1. Align time accuracy of both devfreq_dev_status.total_time and
devfreq_dev_status.busy_time. For example, use "ktime_get()" directly.
2. Align the following timelines:
- The beginning time of devfreq windows
- The beginning of busy time in a new window
- The end of busy time in the current window
Link: https://lore.kernel.org/r/20200611101043.6379-1-stanley.chu@mediatek.com
Fixes: a3cd5ec55f ("scsi: ufs: add load based scaling of UFS gear")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MediaTek UFS clocks are separated to two parts and controlled by different
modules: ufs-mediatek and phy-ufs-mediatek.
If both Auto-Hibern8 and clk-gating feature are enabled, mphy power control
is not balanced thus unbalanced control also happens to the clocks probed
by phy-ufs-mediatek module.
Fix this issue by:
- Promise usage of phy_power_on/off balanced
- Remove phy_power_on/off control in suspend/resume vops since both can be
handled in setup_clock vops only
Link: https://lore.kernel.org/r/20200601104646.15436-5-stanley.chu@mediatek.com
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a chance that link enters hibern8 via auto-hibern8 scheme during
the clock-gating flow. Clocks shall not be gated if link is still active
otherwise host or device may hang.
Fix this by returning error code to the caller __ufshcd_setup_clocks() to
skip gating clocks there if link is not confirmed in hibern8 state yet.
Also allow some waiting time for the hibern8 state transition.
Link: https://lore.kernel.org/r/20200601104646.15436-3-stanley.chu@mediatek.com
Reviewed-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
