[ Upstream commit 64d571742b0ae44eee5efd51e2d4a09d7f6782fc ]
DIV_ROUND_CLOSEST() after kstrtoul() results in an overflow if a large
number such as 18446744073709551615 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
This commit was inspired by commit: 57ee12b6c514.
Fixes: 02ee68b95d ("mt76: mt7915: add control knobs for thermal throttling")
Signed-off-by: xueqin Luo <luoxueqin@kylinos.cn>
Link: https://patch.msgid.link/20241202031917.23741-3-luoxueqin@kylinos.cn
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1b1e133a770fcdbd89551651232b034d2f7a27a ]
When initializing the network card, unplugging the device will
trigger an -EPROTO error, resulting in a flood of error messages
being printed frantically.
The exception is printed as follows：
mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71
mt76x2u 2-2.4:1.0: vendor request req:47 off:9018 failed:-71
...
It will continue to print more than 2000 times for about 5 minutes,
causing the usb device to be unable to be disconnected. During this
period, the usb port cannot recognize the new device because the old
device has not disconnected.
There may be other operating methods that cause -EPROTO, but -EPROTO is
a low-level hardware error. It is unwise to repeat vendor requests
expecting to read correct data. It is a better choice to treat -EPROTO
and -ENODEV the same way.
Similar to commit 9b0f100c19 ("mt76: usb: process URBs with status
EPROTO properly") do no schedule rx_worker for urb marked with status
set -EPROTO. I also reproduced this situation when plugging and
unplugging the device, and this patch is effective.
Just do not vendor request again for urb marked with status set -EPROTO.
Link: https://lore.kernel.org/all/531681bd-30f5-4a70-a156-bf8754b8e072@intel.com/
Link: https://lore.kernel.org/all/D4B9CC1FFC0CBAC3+20250105040607.154706-1-wangyuli@uniontech.com/
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://patch.msgid.link/9DD7DE7AAB497CB7+20250113070241.63590-1-wangyuli@uniontech.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4b6539038c1aa1ae871aacf6e41b566c3613993 ]
When recvmsg with MSG_PEEK flag, the data will be copied to
user's buffer without advancing consume cursor and without
reducing the length of rx available data. Once the expected
peek length is larger than the value of bytes_to_rcv, in the
loop of do while in smc_rx_recvmsg, the first loop will copy
bytes_to_rcv bytes of data from the position local_tx_ctrl.cons,
the second loop will copy the min(bytes_to_rcv, read_remaining)
bytes from the position local_tx_ctrl.cons again because of the
lacking of process with advancing consume cursor and reducing
the length of available data. So do the subsequent loops. The
data copied in the second loop and the subsequent loops will
result in data error, as it should not be copied if no more data
arrives and it should be copied from the position advancing
bytes_to_rcv bytes from the local_tx_ctrl.cons if more data arrives.
This issue can be reproduce by the following python script:
server.py:
import socket
import time
server_ip = '0.0.0.0'
server_port = 12346
server_socket = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
server_socket.bind((server_ip, server_port))
server_socket.listen(1)
print('Server is running and listening for connections...')
conn, addr = server_socket.accept()
print('Connected by', addr)
while True:
data = conn.recv(1024)
if not data:
break
print('Received request:', data.decode())
conn.sendall(b'Hello, client!\n')
time.sleep(5)
conn.sendall(b'Hello, again!\n')
conn.close()
client.py:
import socket
server_ip = '<server ip>'
server_port = 12346
resp=b'Hello, client!\nHello, again!\n'
client_socket = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
client_socket.connect((server_ip, server_port))
request = 'Hello, server!'
client_socket.sendall(request.encode())
peek_data = client_socket.recv(len(resp),
socket.MSG_PEEK | socket.MSG_WAITALL)
print('Peeked data:', peek_data.decode())
client_socket.close()
Fixes: 952310ccf2 ("smc: receive data from RMBE")
Reported-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Link: https://patch.msgid.link/20250104143201.35529-1-guangguan.wang@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 830d8062d25581cf0beaa334486eea06834044da ]
Ralink SoC RT3883 has already 'xtal' defined as a base clock so there is no
need to redefine it again in fixed clocks section. Hence, remove the duplicate
one from there.
Fixes: d34db686a3d7 ("clk: ralink: mtmips: fix clocks probe order in oldest ralink SoCs")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20250108093636.265033-1-sergio.paracuellos@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aaa1a5a9a2ceeb32afa6ea4110a92338a863c33 ]
With change (wifi: mac80211: fix receiving A-MSDU
frames on mesh interfaces), a non-zero TID assignment
is lost during slow path mesh forwarding.
Prior to this change, ieee80211_rx_h_mesh_fwding()
left the TID intact in the header.
As a result of this header corruption, packets belonging
to non-zero TIDs will get treating as belonging
TID 0 by functions such as ieee80211_get_tid().
While this miscategorization by itself is an
issue, there are additional ramifications
due to the fact that skb->priority still reflects
the mesh forwarded packet's ingress (correct) TID.
The mt7915 driver inspects the TID recorded within
skb->priority and relays this to the
hardware/radio during TX. The radio firmware appears to
react to this by changing the sequence control
header, but it does not also ensure/correct the TID in
the QoS control header. As a result, the receiver
will see packets with sequence numbers corresponding
to the wrong TID. The receiver of the forwarded
packet will see TID 0 in QoS control but a sequence number
corresponding to the correct (different) TID in sequence
control. This causes data stalls for TID 0 until
the TID 0 sequence number advances past what the receiver
believes it should be due to this bug.
Mesh routing mpath changes cause a brief transition
from fast path forwarding to slow path forwarding.
Since this bug only affects the slow path forwarding,
mpath changes bring opportunity for the bug to be triggered.
In the author's case, he was experiencing TID 0 data stalls
after mpath changes on an intermediate mesh node.
These observed stalls may be specific
to mediatek radios. But the inconsistency between
the packet header and skb->priority may cause problems
for other drivers as well. Regardless if this causes
connectivity issues on other radios, this change is
necessary in order transmit (forward) the packet on the
correct TID and to have a consistent view a packet's TID
within mac80211.
Fixes: 986e43b19a ("wifi: mac80211: fix receiving A-MSDU frames on mesh interfaces")
Signed-off-by: Andy Strohman <andrew@andrewstrohman.com>
Link: https://patch.msgid.link/20250107104431.446775-1-andrew@andrewstrohman.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f21b77cb556296116b1cce1d62295d13e35da574 ]
commit c4f0755823 ("wifi: mt76: mt7915: fix command timeout in AP stop
period") changes the behavior of mt7915_bss_info_changed() in mesh mode
when enable_beacon becomes false: it calls mt7915_mcu_add_bss_info(...,
false) and mt7915_mcu_add_sta(..., false) while the previous code
didn't. These sends mcu commands that apparently confuse the firmware.
This breaks scanning while in mesh mode on AsiaRF MT7916 DBDC-based cards:
scanning works but no mesh frames get sent afterwards and the firmware
seems to be hosed. It breaks on MT7916 DBDC but not on MT7915 DBDC.
Fixes: c4f0755823 ("wifi: mt76: mt7915: fix command timeout in AP stop period")
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://patch.msgid.link/20240927085350.4594-1-nicolas.cavallari@green-communications.fr
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 996c934c8c196144af386c4385f61fcd5349af28 ]
If firmware boot failes, runtime pm is put too often:
[12092.708099] wlcore: ERROR firmware boot failed despite 3 retries
[12092.708099] wl18xx_driver wl18xx.1.auto: Runtime PM usage count underflow!
Fix that by redirecting all error gotos before runtime_get so that runtime is
not put.
Fixes: c40aad28a3 ("wlcore: Make sure firmware is initialized in wl1271_op_add_interface()")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Michael Nemanov <michael.nemanov@ti.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250104195507.402673-1-akemnade@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 805f7aaf7fee14a57b56af01d270edf6c10765e8 ]
It is possible for multiple, simultaneous callers calling
device_node_get_regmap() with the same node to fail to find an entry in
the syscon_list. There is a period of time while the first caller is
calling of_syscon_register() that subsequent callers also fail to find
an entry in the syscon_list and then call of_syscon_register() a second
time.
Fix this by keeping the lock held until after of_syscon_register()
completes and adds the node to syscon_list. Convert the spinlock to a
mutex as many of the functions called in of_syscon_register() such as
kzalloc() and of_clk_get() may sleep.
Fixes: bdb0066df9 ("mfd: syscon: Decouple syscon interface from platform devices")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20241217-syscon-fixes-v2-1-4f56d750541d@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 769cb63166d90f1fadafa4352f180cbd96b6cb77 ]
The of_syscon_register_regmap() API allows an externally created regmap
to be registered with syscon. This regmap can then be returned to client
drivers using the syscon_regmap_lookup_by_phandle() APIs.
The API is used by platforms where mmio access to the syscon registers is
not possible, and a underlying soc driver like exynos-pmu provides a SoC
specific regmap that can issue a SMC or hypervisor call to write the
register.
This approach keeps the SoC complexities out of syscon, but allows common
drivers such as syscon-poweroff, syscon-reboot and friends that are used
by many SoCs already to be re-used.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240621115544.1655458-2-peter.griffin@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Stable-dep-of: 805f7aaf7fee ("mfd: syscon: Fix race in device_node_get_regmap()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0db017f8edd9b9af818bc1d68ba578df1b4c4628 ]
The kernel coding style does not require 'extern' in function prototypes
in .h files, so remove them as they are not needed.
To avoid checkpatch warnings such as
CHECK: Lines should not end with a '('
+struct regmap *syscon_regmap_lookup_by_phandle(
The indentation is also updated. No functional changes in this patch.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240220115012.471689-3-peter.griffin@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Stable-dep-of: 805f7aaf7fee ("mfd: syscon: Fix race in device_node_get_regmap()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 417cad5dc782096350e6a967ee5dd3417a19a24e ]
cht_wc_leds_probe() leaks memory when the second led_classdev_register()
call in the for-loop fails as it does not call the cleanup function
led_classdev_unregister() on the first device. Avoid this leak by
calling devm_led_classdev_register().
Fixes: 047da762b9 ("leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://lore.kernel.org/r/20241220085346.533675-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80818fdc068eaab729bb793d790ae9fd053f7053 ]
The addition of the "System Do Not Disturb" event code caused the Generic
Desktop D-Pad configuration to be skipped. This commit allows both to be
configured without conflicting with each other.
Fixes: 22d6d060ac77 ("input: Add support for "Do Not Disturb"")
Signed-off-by: Terry Tritton <terry.tritton@linaro.org>
Reviewed-by: Aseda Aboagye <aaboagye@chromium.org>
Reviewed-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f760a4bb5e927a133dcd75f7b69ccae2a331e42c ]
Similar to the earlier fixes meant for sm8x50 and x1e platforms,
we have to stop using the shared clk ops for sdm845 QUPs as well.
As Stephen Boyd pointed out in earlier fixes, there wasn't a problem
to mark QUP clks shared until we started parking shared RCGs at clk
registration time in commit 01a0a6cc8cfd ("clk: qcom: Park shared RCGs
upon registration"). Parking at init is actually harmful to the UART
when earlycon is used. If the device is pumping out data while the
frequency changes and we see garbage on the serial console until the
driver can probe and actually set a proper frequency.
This patch reverts the QUP clk sharing ops part of commit 06391eddb6
("clk: qcom: Add Global Clock controller (GCC) driver for SDM845"), so
that the QUPs on sdm845 don't get parked during clk registration and
break UART operations.
Fixes: 01a0a6cc8cfd ("clk: qcom: Park shared RCGs upon registration")
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/20241209174912.2526928-1-amit.pundir@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3540bba855b4b422e8b977d11aa8173ccb4f089d ]
Currently, when the vdev start WMI cmd is sent from host, vdev related
parameters such as max_reg_power, max_power, and max_antenna_gain are
multiplied by 2 before being sent to the firmware. This is incorrect
because the firmware uses 1 dBm steps for power calculations.
This leads to incorrect power values being used in the firmware and
radio, potentially causing incorrect behavior.
Fix the update of max_reg_power, max_power, and max_antenna_gain values
in the ath12k_mac_vdev_start_restart function, ensuring accurate
power settings in the firmware by sending these values as-is,
without multiplication.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Santhosh Ramesh <quic_santrame@quicinc.com>
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240909073049.3423035-1-quic_santrame@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d38eb7f7b26261a0b642f6e0923269c7c000a97 ]
_opp_add_static_v2() leaks the obtained OF node reference when
_of_opp_alloc_required_opps() fails. Add an of_node_put() call in the
error path.
Fixes: 3466ea2cd6 ("OPP: Don't drop opp->np reference while it is still in use")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dddca3b2fc676113c58b04aaefe84bfb958ac83e ]
of_regulator_match() does not release the OF node reference in the error
path, resulting in an OF node leak. Therefore, call of_node_put() on the
obtained nodes before returning the EINVAL error.
Since it is possible that some drivers call this function and do not
exit on failure, such as s2mps11_pmic_driver, clear the init_data and
of_node in the error path.
This was reported by an experimental verification tool that I am
developing. As I do not have access to actual devices nor the QEMU board
configuration to test drivers that call this function, no runtime test
was able to be performed.
Fixes: 1c8fa58f47 ("regulator: Add generic DT parsing for regulators")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://patch.msgid.link/20250104080453.2153592-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 383ca7bee8a93be9ff5a072936981c2710d2856b ]
Stop force-selecting PLL-MIPI as TCON0 parent, since it breaks video
output on Pinebook that uses RGB to eDP bridge.
Partially revert commit ca1170b699 ("clk: sunxi-ng: a64: force
select PLL_MIPI in TCON0 mux"), while still leaving
CLK_SET_RATE_NO_REPARENT flag set, since we do not want the clock to
be reparented.
The issue is that apparently different TCON0 outputs require a different
clock, or the mux might be selecting the output type.
I did an experiment: I manually configured PLL_MIPI and PLL_VIDEO0_2X
to the same clock rate and flipped the switch with devmem. Experiment
clearly showed that whenever PLL_MIPI is selected as TCON0 clock parent,
the video output stops working.
Therefore, TCON0 clock parent corresponding to the output type must be
assigned in the device tree.
Fixes: ca1170b699 ("clk: sunxi-ng: a64: force select PLL_MIPI in TCON0 mux")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Frank Oltmanns <frank@oltmanns.dev> # on PinePhone
Tested-by: Stuart Gathman <stuart@gathman.org> # on OG Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patch.msgid.link/20250104074035.1611136-5-anarsoul@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fff5da4ca2164bb4d0f1e6cd33f6eb8a0e73e50 ]
Prevent adding a device which is already a team device lower,
e.g. adding veth0 if vlan1 was already added and veth0 is a lower of
vlan1.
This is not useful in practice and can lead to recursive locking:
$ ip link add veth0 type veth peer name veth1
$ ip link set veth0 up
$ ip link set veth1 up
$ ip link add link veth0 name veth0.1 type vlan protocol 802.1Q id 1
$ ip link add team0 type team
$ ip link set veth0.1 down
$ ip link set veth0.1 master team0
team0: Port device veth0.1 added
$ ip link set veth0 down
$ ip link set veth0 master team0
============================================
WARNING: possible recursive locking detected
6.13.0-rc2-virtme-00441-ga14a429069bb #46 Not tainted
--------------------------------------------
ip/7684 is trying to acquire lock:
ffff888016848e00 (team->team_lock_key){+.+.}-{4:4}, at: team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973)
but task is already holding lock:
ffff888016848e00 (team->team_lock_key){+.+.}-{4:4}, at: team_add_slave (drivers/net/team/team_core.c:1147 drivers/net/team/team_core.c:1977)
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(team->team_lock_key);
lock(team->team_lock_key);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by ip/7684:
stack backtrace:
CPU: 3 UID: 0 PID: 7684 Comm: ip Not tainted 6.13.0-rc2-virtme-00441-ga14a429069bb #46
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:122)
print_deadlock_bug.cold (kernel/locking/lockdep.c:3040)
__lock_acquire (kernel/locking/lockdep.c:3893 kernel/locking/lockdep.c:5226)
? netlink_broadcast_filtered (net/netlink/af_netlink.c:1548)
lock_acquire.part.0 (kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5851)
? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973)
? trace_lock_acquire (./include/trace/events/lock.h:24 (discriminator 2))
? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973)
? lock_acquire (kernel/locking/lockdep.c:5822)
? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973)
__mutex_lock (kernel/locking/mutex.c:587 kernel/locking/mutex.c:735)
? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973)
? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973)
? fib_sync_up (net/ipv4/fib_semantics.c:2167)
? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973)
team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973)
notifier_call_chain (kernel/notifier.c:85)
call_netdevice_notifiers_info (net/core/dev.c:1996)
__dev_notify_flags (net/core/dev.c:8993)
? __dev_change_flags (net/core/dev.c:8975)
dev_change_flags (net/core/dev.c:9027)
vlan_device_event (net/8021q/vlan.c:85 net/8021q/vlan.c:470)
? br_device_event (net/bridge/br.c:143)
notifier_call_chain (kernel/notifier.c:85)
call_netdevice_notifiers_info (net/core/dev.c:1996)
dev_open (net/core/dev.c:1519 net/core/dev.c:1505)
team_add_slave (drivers/net/team/team_core.c:1219 drivers/net/team/team_core.c:1977)
? __pfx_team_add_slave (drivers/net/team/team_core.c:1972)
do_set_master (net/core/rtnetlink.c:2917)
do_setlink.isra.0 (net/core/rtnetlink.c:3117)
Reported-by: syzbot+3c47b5843403a45aef57@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=3c47b5843403a45aef57
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: Octavian Purdila <tavip@google.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9b7c84d22fb1687d63ca2a386773015cf59436b ]
The CLKOUTn may be fed from PLL1/2/3, but the PLL1/2/3 has to be enabled
first by setting PLL_CLKE bit 11 in CCM_ANALOG_SYS_PLLn_GEN_CTRL register.
The CCM_ANALOG_SYS_PLLn_GEN_CTRL bit 11 is modeled by plln_out clock. Fix
the clock tree and place the clkout1/2 under plln_sel instead of plain plln
to let the clock subsystem correctly control the bit 11 and enable the PLL
in case the CLKOUTn is supplied by PLL1/2/3.
Fixes: 43896f56b5 ("clk: imx8mp: add clkout1/2 support")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20241112013718.333771-1-marex@denx.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9ba290d0b829012574b6821ba08815046e60c94 ]
determine_rate() callback is used by the clk_set_rate() API to get the
closest rate of the target rate supported by the clock. If this callback
is not implemented (nor round_rate() callback), then the API will assume
that the clock cannot set the requested rate. And since there is no parent,
it will return -EINVAL.
This is not an issue right now as clk_set_rate() mistakenly compares the
target rate with cached rate and bails out early. But once that is fixed
to compare the target rate with the actual rate of the clock (returned by
recalc_rate()), then clk_set_rate() for this clock will start to fail as
below:
cpu cpu0: _opp_config_clk_single: failed to set clock rate: -22
So implement the determine_rate() callback that just returns the actual
rate at which the clock is passed to the CPUs in a domain.
Fixes: 4370232c72 ("cpufreq: qcom-hw: Add CPU clock provider support")
Reported-by: Johan Hovold <johan+linaro@kernel.org>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85d8b11351a8f15d6ec7a5e97909861cb3b6bcec ]
Currently, qcom_cpufreq_hw_recalc_rate() returns the LMh throttled
frequency for the domain even if LMh IRQ is not available. But as per
qcom_cpufreq_hw_get(), the driver has to query LUT entries to get the
actual frequency of the domain. So do the same in
qcom_cpufreq_hw_recalc_rate().
While doing so, refactor the existing qcom_cpufreq_hw_get() function so
that qcom_cpufreq_hw_recalc_rate() can make use of the existing code and
avoid code duplication. This also requires setting the
qcom_cpufreq_data::policy even if LMh IRQ is not available.
Fixes: 4370232c72 ("cpufreq: qcom-hw: Add CPU clock provider support")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53c59d66c44c5eb98b34da9967f937e5387f8624 ]
Curtrently the error path is unsynchronised with removal due to
regulator being disabled before other device managed resources
are handled. Correct that by wrapping regulator enablement in
the respective call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 7cef813a91c4 ("gpio: pca953x: log an error when failing to get the reset GPIO")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f4d3e293392571e02b106c8b431b638bd029276 ]
New code should solely use firmware nodes for the specifics and
not any callbacks.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 7cef813a91c4 ("gpio: pca953x: log an error when failing to get the reset GPIO")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e461a1cb43d69d2fc8a97e61916dce571e6bb31 ]
A redundant frequency update is only truly needed when there is a policy
limits change with a driver that specifies CPUFREQ_NEED_UPDATE_LIMITS.
In spite of that, drivers specifying CPUFREQ_NEED_UPDATE_LIMITS receive a
frequency update _all the time_, not just for a policy limits change,
because need_freq_update is never cleared.
Furthermore, ignore_dl_rate_limit()'s usage of need_freq_update also leads
to a redundant frequency update, regardless of whether or not the driver
specifies CPUFREQ_NEED_UPDATE_LIMITS, when the next chosen frequency is the
same as the current one.
Fix the superfluous updates by only honoring CPUFREQ_NEED_UPDATE_LIMITS
when there's a policy limits change, and clearing need_freq_update when a
requisite redundant update occurs.
This is neatly achieved by moving up the CPUFREQ_NEED_UPDATE_LIMITS test
and instead setting need_freq_update to false in sugov_update_next_freq().
Fixes: 600f5badb7 ("cpufreq: schedutil: Don't skip freq update when limits change")
Signed-off-by: Sultan Alsawaf (unemployed) <sultan@kerneltoast.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/20241212015734.41241-2-sultan@kerneltoast.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a853c609504e2d1d83e71285e3622fda1f1451d8 ]
All inet_getpeer() callers except ip4_frag_init() don't need
to acquire a permanent refcount on the inetpeer.
They can switch to full RCU protection.
Move the refcount_inc_not_zero() into ip4_frag_init(),
so that all the other callers no longer have to
perform a pair of expensive atomic operations on
a possibly contended cache line.
inet_putpeer() no longer needs to be exported.
After this patch, my DUT can receive 8,400,000 UDP packets
per second targeting closed ports, using 50% less cpu cycles
than before.
Also change two calls to l3mdev_master_ifindex() by
l3mdev_master_ifindex_rcu() (Ido ideas)
Fixes: 8c2bd38b95f7 ("icmp: change the order of rate limits")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241215175629.1248773-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50b362f21d6c10b0f7939c1482c6a1b43da82f1a ]
inet_putpeer() will be removed in the following patch,
because we will no longer use refcounts.
Update inetpeer timestamp (p->dtime) at lookup time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241215175629.1248773-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: a853c609504e ("inetpeer: do not get a refcount in inet_getpeer()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0508316be63bb735f59bdc8fe4527cadb62210ca ]
netxbig_leds_get_of_pdata() does not release the OF node obtained by
of_parse_phandle() when of_find_device_by_node() fails. Add an
of_node_put() call to fix the leak.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 9af512e819 ("leds: netxbig: Convert to use GPIO descriptors")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://lore.kernel.org/r/20241216074923.628509-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6856edf7ead8c54803216a38a7b227bcb3dadff7 ]
The sense resistor used for measuring currents is typically some tens of
milli Ohms. It has accidentally been documented to be tens of mega Ohms.
Fix the size of this resistor and a few copy-paste errors while at it.
Drop the unsuitable 'rohm,charger-sense-resistor-ohms' property (which
can't represent resistors smaller than one Ohm), and introduce a new
'rohm,charger-sense-resistor-micro-ohms' property with appropriate
minimum, maximum and default values instead.
Fixes: 4238dc1e64 ("dt_bindings: mfd: Add ROHM BD71815 PMIC")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/0efd8e9de0ae8d62ee4c6b78cc565b04007a245d.1731430700.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d6c0e58514f8b57cd9c2c755e41623d6a966025 ]
Commit 'cpupower: Make TSC read per CPU for Mperf monitor' (c2adb1877b)
changes TSC counter reads per cpu, but left time diff global (from start
of all cpus to end of all cpus), thus diff(time) is too large for a
cpu's tsc counting, resulting in far less than acutal TSC_Mhz and thus
`cpupower monitor` showing far less than actual cpu realtime frequency.
/proc/cpuinfo shows frequency:
cat /proc/cpuinfo | egrep -e 'processor' -e 'MHz'
...
processor : 171
cpu MHz : 4108.498
...
before fix (System 100% busy):
| Mperf || Idle_Stats
CPU| C0 | Cx | Freq || POLL | C1 | C2
171| 0.77| 99.23| 2279|| 0.00| 0.00| 0.00
after fix (System 100% busy):
| Mperf || Idle_Stats
CPU| C0 | Cx | Freq || POLL | C1 | C2
171| 0.46| 99.54| 4095|| 0.00| 0.00| 0.00
Fixes: c2adb1877b ("cpupower: Make TSC read per CPU for Mperf monitor")
Signed-off-by: He Rongguang <herongguang@linux.alibaba.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c759bc8e9046f9812238f506d70f07d3ea4206d4 ]
Call thermal_cooling_device_unregister() and sysfs_remove_link() in the
error path of acpi_fan_probe() to fix possible memory leak.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 05a83d9722 ("ACPI: register ACPI Fan as generic thermal cooling device")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://patch.msgid.link/20241211032812.210164-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b05d30c2b6df7e2172b18bf1baee9b202f9c6b53 ]
Including the fwil.h header file can lead to a build error:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h: \
In function ‘brcmf_fil_cmd_int_set’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h:90:9: error: implicit \
declaration of function ‘brcmf_dbg’ [-Werror=implicit-function-declaration]
90 | brcmf_dbg(FIL, "ifidx=%d, cmd=%d, value=%d\n", ifp->ifidx, cmd, data);
| ^~~~~~~~~
The error is often avoided because the debug.h header file is included
before the fwil.h header file.
This makes sure the header include order is irrelevant by explicitly adding the
debug.h header.
Fixes: 31343230abb1 ("wifi: brcmfmac: export firmware interface functions")
Signed-off-by: Marcel Hamer <marcel.hamer@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241211133618.2014083-1-marcel.hamer@windriver.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08242719a8af603db54a2a79234a8fe600680105 ]
The "regulator-compatible" property has been deprecated since 2012 in
commit 13511def87 ("regulator: deprecate regulator-compatible DT
property"), which is so old it's not even mentioned in the converted
regulator bindings YAML file. It should not have been used for new
submissions such as the MT6315.
Drop the property from the MT6315 regulator binding and its examples.
Fixes: 977fb5b584 ("regulator: document binding for MT6315 regulator")
Fixes: 6d435a94ba ("regulator: mt6315: Enforce regulator-compatible, not name")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20241211052427.4178367-2-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ade5e05bd094485ce370fad66a6a3fb6f50bfbc ]
Commit c8000deb68365b ("HID: multitouch: Add support for GT7868Q") added
support for 0x01e8 and 0x01e9, but the mt_device[] entries were added
twice for 0x01e8 and there was none added for 0x01e9. Fix that.
Fixes: c8000deb68365b ("HID: multitouch: Add support for GT7868Q")
Reported-by: He Lugang <helugang@uniontech.com>
Reported-by: WangYuli <wangyuli@uniontech.com>
Reported-by: Ulrich Müller <ulm@gentoo.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b59b86c5d08be7d761c04affcbcec8184738c200 ]
At probe error path, the firmware loading work may have already been
queued. In such a case, it will try to access memory allocated by the probe
function, which is about to be released. In such paths, wait for the
firmware worker to finish before releasing memory.
Fixes: 3d86b93064 ("rtlwifi: Fix PCI probe error path orphaned memory")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241206173713.3222187-5-cascardo@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
