[ Upstream commit 6e0af29806 ]
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8159ecab0d ]
Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.
The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.
A message is logged when the above scenario occurs:
macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor
Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.
This issue was observed on a ZynqMP based system.
Fixes: 4df95131ea ("net/macb: change RX path for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e100a897bf ]
64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.
The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.
Fix that by adding the necessary DMA memory barrier between the writes.
This corruption was observed on a ZynqMP based system.
Fixes: fff8019a08 ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: Harini Katakam <harini.katakam@xilinx.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07d427689 ]
We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.
Fixes: d2201a2159 ("qed: No need for LL2 frags indication")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf76785d30 ]
Ensure that we clear XPRT_CONNECTING before releasing the XPRT_LOCK so that
we don't have races between the (asynchronous) socket setup code and
tasks in xprt_connect().
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a50e5fb8db ]
Recently TXQ teardown was moved earlier in ieee80211_unregister_hw(),
to avoid a use-after-free of the netdev data. However, interfaces
aren't fully removed at the point, and cfg80211_shutdown_all_interfaces
can for example, TX a deauth frame. Move the TXQ teardown to the
point between cfg80211_shutdown_all_interfaces and the free of
netdev queues, so we can be sure they are torn down before netdev
is freed, but after there is no ongoing TX.
Fixes: 77cfaf52ec ("mac80211: Run TXQ teardown code before de-registering interfaces")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6adafc356e ]
Create a net bridge, add eth and vnet to the bridge. The vnet is used
by a virtual machine. When ping the virtual machine from the outside
host and the virtual machine send multicast at the same time, the ping
package will lost.
The multicast package send to the eth, eth will send it to the bridge too,
and the bridge learn the mac of eth. When outside host ping the virtual
mechine, it will match the promisc entry of the eth which is not expected,
and the bridge send it to eth not to vnet, cause ping lost.
So this patch change promisc tcam entry position to the END of 512 tcam
entries, which indicate lower priority. And separate one promisc entry to
two: mc & uc, to avoid package match the wrong tcam entry.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 726ae5c9e5 ]
In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.
Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e74a19ca5 ]
The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a57275d355 ]
There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.
So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.
When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c82bd077e1 ]
1.In "hns_nic_init_irq", if request irq fail at index i,
the function return directly without releasing irq resources
that already requested.
2.In "hns_nic_net_up" after "hns_nic_init_irq",
if exceptional branch occurs, irqs that already requested
are not release.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31f6b61d81 ]
If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.
This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5778b13b64 ]
After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.
Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
smp_mb__before_clear_bit();
clear_bit(NAPI_STATE_SCHED, &n->state);
}
[37255.571996] Kernel panic - not syncing: BUG!
[37255.595234] Call trace:
[37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0
[37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28
[37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8
[37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c
[37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0
[37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c
[37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168
[37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c
[37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68
[37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704
[37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4
[37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84
[37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c
[37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618
[37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4
[37255.801139] SMP: stopping secondary CPUs
[37255.805079] kbox: catch panic event.
[37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072
[37255.816103] flush cache 0xffff80003f000000 size 0x800000
[37255.822192] flush cache 0xffff80003f000000 size 0x800000
[37255.828289] flush cache 0xffff80003f000000 size 0x800000
[37255.834378] kbox: no notify die func register. no need to notify
[37255.840413] ---[ end Kernel panic - not syncing: BUG!
This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ad26f117b ]
According to the hip06 datasheet:
1.Six registers use wrong address:
RCB_COM_SF_CFG_INTMASK_RING
RCB_COM_SF_CFG_RING_STS
RCB_COM_SF_CFG_RING
RCB_COM_SF_CFG_INTMASK_BD
RCB_COM_SF_CFG_BD_RINT_STS
DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
overwrite
These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 308c6cafde ]
There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
and install them again, must use "ifconfig down/ifconfig up"
command pair to bring port to work.
This patch calls phy_stop function when init phy to fix this bug.
2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
all ports can not use anymore, because of the phy devices register
failed(phy devices already exists).
Phy devices are registered when hns_dsaf installed, this patch
removes them when hns_dsaf removed.
The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e1d4be681 ]
According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51367e423c ]
The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:
WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init
Remove the __init to make it always do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c0563e442 ]
create_ctx is called from tls_init and tls_hw_prot
hence initialize function pointers in common routine.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab4c3426c ]
Clang warns:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
^
1 warning generated.
Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c629421a99 ]
Need to be able to boot without PCI devices present.
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c250f4612 ]
Starting from mac80211 commit adf8ed01e4 ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 801df68d61 ]
csk leak can happen if a new TCP connection gets established after
cxgbit_accept_np() returns, to fix this leak free remaining csk in
cxgbit_free_np().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9061193c4e ]
Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04f05230c5 ]
Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbf666c1af ]
On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4e7df1656 ]
rbnode in insert_tree() is rcu protected pointer.
So, in order to handle this pointer, _rcu function should be used.
rb_link_node_rcu() is a rcu version of rb_link_node().
Fixes: 34848d5c89 ("netfilter: nf_conncount: Split insert and traversal")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 708abf74dd ]
In the error handling block, nla_nest_cancel(skb, atd) is called to
cancel the nest operation. But then, ipset_nest_end(skb, atd) is
unexpected called to end the nest operation. This patch calls the
ipset_nest_end only on the branch that nla_nest_cancel is not called.
Fixes: 45040978c8 ("netfilter: ipset: Fix set:list type crash when flush/dump set in parallel")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96d1a73161 ]
When the VF driver does a reset, it (at least the Linux one) writes to
the VFCTRL register to issue a reset and then immediately sends a reset
message using the mailbox API. This is racy because when the PF driver
detects that the VFCTRL register reset pin has been asserted, it clears
the mailbox memory. Depending on ordering, the reset message sent by
the VF could be cleared by the PF driver. It then responds to the
cleared message with a NACK which causes the VF driver to malfunction.
Fix this by deferring clearing the mailbox memory until the reset
message is received.
Fixes: 939b701ad6 ("ixgbe: fix driver behaviour after issuing VFLR")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 158daed16e ]
A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().
Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.
Fixes: 458867b2ca ("i40e: don't remove netdev->dev_addr when syncing uc list")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e41cae64b ]
gcc warning this:
drivers/net/ieee802154/ca8210.c:730:10: warning:
comparison is always false due to limited range of data type [-Wtype-limits]
'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.
Fixes: ded845a781 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca5047286c ]
Before commit 7fd6d98b89 ("i2c: i801: Allow ACPI AML access I/O
ports not reserved for SMBus"), enabling RMI on the T560 would cause
the touchpad to stop working after resuming from suspend. Now that
this issue is fixed, RMI can be enabled safely and works fine.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2ca26ec4f ]
With PM enabled, I noticed that pressing a key on the droid4 keyboard will
block deeper idle states for the SoC. Let's fix this by using IRQF_ONESHOT
and stop constantly toggling the device OMAP4_KBD_IRQENABLE register as
suggested by Dmitry Torokhov <dmitry.torokhov@gmail.com>.
From the hardware point of view, looks like we need to manage the registers
for OMAP4_KBD_IRQENABLE and OMAP4_KBD_WAKEUPENABLE together to avoid
blocking deeper SoC idle states. And with toggling of OMAP4_KBD_IRQENABLE
register now gone with IRQF_ONESHOT, also the SoC idle state problem is
gone during runtime. We still also need to clear OMAP4_KBD_WAKEUPENABLE in
omap4_keypad_close() though to pair it with omap4_keypad_open() to prevent
blocking deeper SoC idle states after rmmod omap4-keypad.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ae4f8420e ]
If "interface" is NULL then we can't release it and trying to will only
lead to an Oops.
Fixes: aea71a0249 ("[SCSI] bnx2fc: Introduce interface structure for each vlan interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 530aad7701 ]
When adjusting sack block sequence numbers, skb_make_writable() gets
called to make sure tcp options are all in the linear area, and buffer
is not shared.
This can cause tcp header pointer to get reallocated, so we must
reaload it to avoid memory corruption.
This bug pre-dates git history.
Reported-by: Neel Mehta <nmehta@google.com>
Reported-by: Shane Huntley <shuntley@google.com>
Reported-by: Heather Adkins <argv@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0152eee6fc ]
Since commit 222d7dbd25 ("net: prevent dst uses after free")
skb_dst_force() might clear the dst_entry attached to the skb.
The xfrm code doesn't expect this to happen, so we crash with
a NULL pointer dereference in this case.
Fix it by checking skb_dst(skb) for NULL after skb_dst_force()
and drop the packet in case the dst_entry was cleared. We also
move the skb_dst_force() to a codepath that is not used when
the transformation was offloaded, because in this case we
don't have a dst_entry attached to the skb.
The output and forwarding path was already fixed by
commit 9e14379378 ("xfrm: Fix NULL pointer dereference when
skb_dst_force clears the dst_entry.")
Fixes: 222d7dbd25 ("net: prevent dst uses after free")
Reported-by: Jean-Philippe Menil <jpmenil@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 533555e5cb ]
xfrm_output_one() does not return a error code when there is
no dst_entry attached to the skb, it is still possible crash
with a NULL pointer dereference in xfrm_output_resume(). Fix
it by return error code -EHOSTUNREACH.
Fixes: 9e14379378 ("xfrm: Fix NULL pointer dereference when skb_dst_force clears the dst_entry.")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1733a1d3c ]
There is actually a space after "sp," like this,
ffff2000080813c8: a9bb7bfd stp x29, x30, [sp, #-80]!
Right now, checkstack.pl isn't able to print anything on aarch64,
because it won't be able to match the stating objdump line of a function
due to this missing space. Hence, it displays every stack as zero-size.
After this patch, checkpatch.pl is able to match the start of a
function's objdump, and is then able to calculate each function's stack
correctly.
Link: http://lkml.kernel.org/r/20181207195843.38528-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37fbd834b4 ]
When support for bonding of RoCE devices was added, there was
necessarily a link between the RoCE device and the paired netdevice that
was part of the bond. If you remove the mlx4_en module, that paired
association is broken (the RoCE device is still present but the paired
netdevice has been released). We need to account for this in
is_upper_ndev_bond_master_filter() and filter out those links with a
broken pairing or else we later oops in netdev_next_upper_dev_rcu().
Fixes: 408f1242d9 ("IB/core: Delete lower netdevice default GID entries in bonding scenario")
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c554206077 ]
If CS is submitted using guilty ctx, we terminate amdgpu_cs_parser_init
before locking ctx->lock, latter in amdgpu_cs_parser_fini we still are
trying to release the lock just becase parser->ctx != NULL.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ef34630a4 ]
The "altmap" is used to provide a pool of memory that is reserved for
the vmemmap backing of hot-plugged memory. This is useful when adding
large amount of ZONE_DEVICE memory to a system with a limited amount of
normal memory.
On ppc64 we use huge pages to map the vmemmap which requires the backing
storage to be contigious and aligned to the hugepage size. The altmap
implementation allows for the altmap provider to reserve a few PFNs at
the start of the range for it's own uses and when this occurs the
first chunk of the altmap is not usable for hugepage mappings. On hash
there is no sane way to fall back to a normal sized page mapping so we
fail the allocation. This results in memory hotplug failing with
ENOMEM when the new range doesn't fall into an existing vmemmap block.
This patch handles this case by falling back to using system memory
rather than failing if we cannot allocate from the altmap. This
fallback should only ever be used for the first vmemmap block so it
should not cause excess memory consumption.
Fixes: 7b73d978a5 ("mm: pass the vmem_altmap to vmemmap_populate")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
