When setting the OpenDrain bit we should really honour the
argument passed inside the devicetree.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While converting the boards inside OpenWrt to OF I noticed
that the we are missing a pinconf parameter to set a pin
to output.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While converting all the boards supported by OpenWrt to OF
I noticed that this feature is missing. Adding it makes the
devicetrees more readable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The logic of the OD bit was inverted when calling the
pinconf get method.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The XWAY pinctrl driver invalidly uses the port and not the pin
number to work out the registers and bits to be set for the
opendrain and pullup/down resistors.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The reboot just wants to get to the next kernel. But if a warning (Call
Trace) appears, the monitor will report an error, and the reboot will
think something went wrong and power cycle the box, even though we
successfully made it to the next kernel.
Ignore warnings during the reboot until we get to the next kernel. It
will still timeout if we never get to the next kernel and then a power
cycle will happen. That's what we want it to do.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The device removal code was incorrectly checking against two different limits for
raid5 and raid6.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Sometimes when a test kernel passed fine, but on reboot it crashed,
ktest could get stuck and not proceed. This would be frustrating if you
let a test run overnight to find out the next morning that it was stuck
on the first test.
To fix this, I made reboot check for the REBOOT_SUCCESS_LINE. If the
line was not detected, then it would power cycle the box.
What it didn't cover was if the REBOOT_SUCCESS_LINE wasn't defined or if
a 'good' kernel did not display the line. Instead have it search for the
Linux banner "Linux version". The reboot just needs to get to the start
of the next kernel, it does not need to test if the next kernel makes it
to a boot prompt.
After we find the next kernel has booted, then we just wait for either
the REBOOT_SUCCESS_LINE to appear or the timeout.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch reduces and simplifies initalization code by
using module_platform_driver().
With this change it's necessary to remove the __init annotation
to avoid section mismatch warnings.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The hardware does not support keeping CS asserted after sending one
FIFO buffer worth of data, so reject transfers requiring CS being kept
asserted, either between transers or for a certain time after it,
or exceeding the FIFO size.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use GFP_DMA in order to ensure that the memory we allocate for transfers
in spi_write_then_read() can be DMAed. On most platforms this will have
no effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The driver should setup mode bits it supports, otherwise
adding an SPI device might fail even if the driver supports
the requested SPI mode.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove deprecated cell-index property and use spi alias to
obtain the SPI PSC number used for SPI bus id.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some of the spi driver module remove hooks were annotated with __exit
and referenced with __exit_p(). Presumably these were supposed to be
__devinit, __devexit and __devexit_p() since __init/__exit for a
probe/remove hook has never been correct. They also got missed during
the big __devinit/__devexit purge since they didn't match the pattern.
Remove then now to be rid of it.
v2: purge __init also
Reported-by: Arnd Bergmann <arnd@arndb.de>
[Arnd set a patch cleaning up one, and then I found more]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These routines are used by server and client code, so having them in a
separate header would be best.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
When copying an address, we should also copy the scopeid in the event
that this is a link-local address and the scope matters.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
We don't really need to preallocate at all; just allocate and initialize
everything at once, but leave the sc_type field initially 0 to prevent
finding the stateid till it's fully initialized.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
the default of_gpio_simple_xlate() will make us fail while getting gpios
bigger than 32 by of_get_named_gpio() or related APIs.
this patch adds a specific of_xlate callback for sirf gpio_chip and fix
the problem.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit cf844751fb ("ARM: at91: drop ide driver in favor of the pata
one") removed the at91-ide driver but did not remove the Kconfig entry.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ASoC compressed API did not implement the copy callback in its
compressed ops which is required for DSPs that are not memory mapped.
This patch creates a local copy of the compress ops for each runtime and
modifies them with a copy callback as appropriate.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With new transports coming up, move to threaded
interrupt handling now. This has the advantage
that we can use the same locking scheme with all
different transports we may need to implement.
Note that the TX path obviously still runs in a
tasklet, so some spin_lock() calls need to change
to spin_lock_bh() calls to properly lock out the
TX path.
In my test on a Calpella platform this has no
impact on throughput or latency.
Also add lockdep annotations to avoid lockups due
to catch sending synchronous commands or using
locks that connect with them from the irq thread.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch cleans up cosmetic issues, remove useless functions and add
to_lnw_priv() macro to replace many usages of container_of().
Signed-off-by: David Cohen <david.a.cohen@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add gpio support for Intel Lynxpoint chipset.
Lynxpoint supports 94 gpio pins which can generate interrupts.
Driver will fail requests for pins that are marked as owned by ACPI, or
set in an alternate mode (non-gpio).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix checkpatch warnings and error as below:
ERROR: "foo * bar" should be "foo *bar"
WARNING: please, no space before tabs
WARNING: quoted string split across lines
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use devm_clk_get() and devm_request_irq() rather than clk_get() and
request_irq() to make cleanup paths more simple.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Theoretically TEGRA_IOMMU_SMMU depends on ARCH_TEGRA_3x_SOC and
ARCH_TEGRA_114_SOC only. This patch allows a Tegra20 only kernel to
enable SMMU(Tegra20 doesn't have a SMMU), which could avoid editing
this Kconfig entry every time we add a new chip later.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Do not repeat the checking loop in the read and write
functions. Use a single helper function for that check and
call it in both accessors.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Presently SMMU registers are located in discontiguous 3 blocks. They
are interleaved by MC registers. Ideally SMMU register blocks should
be in an independent one block, but it is too late to change this H/W
design. In the future Tegra chips over some generations, it is
expected that some of register block "size" can be extended towards
the end and also more new register blocks will be added at most a few
blocks. The starting address of each existing block won't change. This
patch allocates multiple number of register blocks dynamically based
on the info passed from DT. Those ranges are verified in the
accessors{read,write}. This may sacrifice some performance because a
new accessors prevents compiler optimization of a fixed size register
offset calculation. Since SMMU register accesses are not so frequent,
this would be acceptable. This patch is necessary to unify
"tegra-smmu.ko" over some Tegra SoC generations.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch includes the device driver for the IBM RamSan
family of PCI SSD flash storage cards. This driver will
include support for the RamSan 70 and 80. The driver
presents a block device for device I/O.
Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
SPI core make sure that all transfer has proper speed set
before calling low level spi transfer. Hence, it is not
require to have check in spi driver.
Remove the check for speed validity from transfer and use it directly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When spi client does the spi transfer and if it does not set
the speed for each transfer then set it as default
of spi device in spi core before calling low level transfer.
This will remove the extra check in low level driver for setting
speed.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently we are initializing the SPI controller in
the chip select line function, and that function is
called once for each SPI device on the bus. If a
board has multiple SPI devices, the controller will
be initialized multiple times.
Introduce ath79_spi_{en,dis}able helper functions,
and call those from probe/response in order to avoid
the mutliple initialization of the controller.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The spi_bitbang driver calls the chipselect function
of the driver from spi_bitbang_setup in order to
deselect the given SPI chip, so we don't have to
initialize the CS line here.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The 'ath79_spi_txrx_mode0' function does not
set the SCK signal to LOW at the end of a word
transfer. This causes communications errors with
certain devices (e.g. the PCF2123 RTC chip).
The patch ensures that the SCK signal will be LOW.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The driver uses the "as fast as it can" approach
to drive the SCK signal. However this does not
work with certain low speed SPI chips (e.g. the
PCF2123 RTC chip).
The patch adds per-bit slowdowns in order to be
able to use the driver with such chips as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
