[ Upstream commit cdf10ffe8f ]
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c097 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18b8f5b6fc ]
mips_cm_error_report() extracts the cause and other cause from the error
register using shifts. This works fine for the former, as it is stored
in the top bits, and the shift will thus remove all non-related bits.
However, the latter is stored in the bottom bits, hence thus needs masking
to get rid of non-related bits. Without such masking, using it as an
index into the cm2_causes[] array will lead to an out-of-bounds access,
probably causing a crash.
Fix this by using FIELD_GET() instead. Bite the bullet and convert all
MIPS CM handling to the bitfield API, to improve readability and safety.
Fixes: 3885c2b463 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 778a0cbef5 ]
The setting from the cirrus,ts-inv property should be applied to the
TIP_SENSE_INV bit, as this is the one that actually affects the jack
detect block. The TS_INV bit only swaps the meaning of the PLUG and
UNPLUG interrupts and should always be 1 for the interrupts to have
the normal meaning.
Due to some misunderstanding the driver had been implemented to
configure the TS_INV bit based on the jack switch polarity. This made
the interrupts behave the correct way around, but left the jack detect
block, button detect and analogue circuits always interpreting an open
switch as unplugged.
The signal chain inside the codec is:
SENSE pin -> TIP_SENSE_INV -> TS_INV -> (invert) -> interrupts
|
v
Jack detect,
button detect and
analog control
As the TIP_SENSE_INV already performs the necessary inversion the
TS_INV bit never needs to change. It must always be 1 to yield the
expected interrupt behaviour.
Some extra confusion has arisen because of the additional invert in the
interrupt path, meaning that a value applied to the TS_INV bit produces
the opposite effect of applying it to the TIP_SENSE_INV bit. The ts-inv
property has therefore always had the opposite effect to what might be
expected (0 = inverted, 1 = not inverted). To maintain the meaning of
the ts-inv property it must be inverted when applied to TIP_SENSE_INV.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211028140902.11786-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43775e62c4 ]
The wait_for_completion_timeout function returns 0 if timed out or a
positive value if completed. Hence, "less than zero" comparison always
misses timeouts and doesn't kill the URB as it should, leading to
re-sending it while it is active.
Fixes: 42337b9d4d ("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7abf78b7a ]
The previous commit fixed handling of incomplete packets but broke error
handling: offsetof returns an unsigned value (size_t), but when compared
against the signed return value, the return value is interpreted as if
it were unsigned, so negative return values are never less than the
offset.
To make the code easier to read, calculate the minimal packet length
once and separately, and assign it to a signed int variable to eliminate
unsigned math and the need for type casts. It then becomes immediately
obvious how the actual data length is calculated and why the return
value cannot be less than the minimal length.
Fixes: 22d65765f2 ("HID: u2fzero: ignore incomplete packets without data")
Fixes: 42337b9d4d ("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88b20f84f0 ]
xilinx_uartps .start_tx() clears TXEMPTY when enabling TXEMPTY to avoid
any previous TXEVENT event asserting the UART interrupt. This clear
operation is done immediately after filling the TX FIFO.
However, if the bytes inserted by cdns_uart_handle_tx() are consumed by
the UART before the TXEMPTY is cleared, the clear operation eats the new
TXEMPTY event as well, causing cdns_uart_isr() to never receive the
TXEMPTY event. If there are bytes still queued in circbuf, TX will get
stuck as they will never get transferred to FIFO (unless new bytes are
queued to circbuf in which case .start_tx() is called again).
While the racy missed TXEMPTY occurs fairly often with short data
sequences (e.g. write 1 byte), in those cases circbuf is usually empty
so no action on TXEMPTY would have been needed anyway. On the other
hand, longer data sequences make the race much more unlikely as UART
takes longer to consume the TX FIFO. Therefore it is rare for this race
to cause visible issues in general.
Fix the race by clearing the TXEMPTY bit in ISR *before* filling the
FIFO.
The TXEMPTY bit in ISR will only get asserted at the exact moment the
TX FIFO *becomes* empty, so clearing the bit before filling FIFO does
not cause an extra immediate assertion even if the FIFO is initially
empty.
This is hard to reproduce directly on a normal system, but inserting
e.g. udelay(200) after cdns_uart_handle_tx(port), setting 4000000 baud,
and then running "dd if=/dev/zero bs=128 of=/dev/ttyPS0 count=50"
reliably reproduces the issue on my ZynqMP test system unless this fix
is applied.
Fixes: 85baf542d5 ("tty: xuartps: support 64 byte FIFO size")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/r/20211026102741.2910441-1-anssi.hannula@bitwise.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b475bf0ec4 ]
The FSEL_MASK which selects the refclock is defined incorrectly.
It should be [4:6] not [5:7]. Due to this incorrect definition, the BIT(7)
in USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0 is reset which keeps PHY analog
blocks ON during suspend.
Fix this issue by correctly defining the FSEL_MASK.
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Link: https://lore.kernel.org/r/1635135575-5668-1-git-send-email-quic_c_sanm@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d387f61b0 ]
In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cab2a24f ]
Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c
When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b600bd7eb3 ]
With commit ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
we are doing a HW or SW reset to the device which means that we'll get
the default state of the data ready pin (which is enabled). Hence there's
no point in disabling the IRQ in the init function. Moreover, this
function is intended to initialize internal data structures and not
really do anything on the device.
As a result of this, some devices were left with the data ready pin enabled
after probe which was not the desired behavior. Thus, we move the call to
'adis_enable_irq()' to the initial startup function where it makes more
sense for it to be.
Note that for devices that cannot mask/unmask the pin, it makes no sense
to call the function at this point since the IRQ should not have been
yet requested. This will be improved in a follow up change.
Fixes: ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210903141423.517028-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3e56c050a ]
The general expectation is that powering on a power-domain should make
the power domain deliver some power, and if a specific performance state
is needed further requests has to be made.
But in contrast with other power-domain implementations (e.g. rpmpd) the
RPMh does not have an interface to enable the power, so the driver has
to vote for a particular corner (performance level) in rpmh_power_on().
But the corner is never initialized, so a typical request to simply
enable the power domain would not actually turn on the hardware. Further
more, when no more clients vote for a performance state (i.e. the
aggregated vote is 0) the power domain would be turned off.
Fix both of these issues by always voting for a corner with non-zero
value, when the power domain is enabled.
The tracking of the lowest non-zero corner is performed to handle the
corner case if there's ever a domain with a non-zero lowest corner, in
which case both rpmh_power_on() and rpmh_rpmhpd_set_performance_state()
would be allowed to use this lowest corner.
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211005033732.2284447-1-bjorn.andersson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f87a74d31 ]
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes: 5afd65c3a0 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2012579b31 ]
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes: 76045bc457 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab1891640 ]
Commit 723de0f917 ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem.
Dim2 used to register the same struct device to provide a custom device
attribute. This causes double-registration of the same struct device.
Fix that by moving the custom attribute to driver's dev_groups.
This moves attribute to the platform_device object, which is a better
location for platform-specific attributes anyway.
Fixes: 723de0f917 ("staging: most: remove device from interface structure")
Acked-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211011061117.21435-1-nikita.yoush@cogentembedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4875d509a ]
This variable is just a temporary variable, used to do an endian
conversion. The problem is that the last byte is not initialized. After
the conversion is completely done, the last byte is discarded so it doesn't
cause a problem. But static checkers and the KMSan runtime checker can
detect the uninitialized read and will complain about it.
Link: https://lore.kernel.org/r/20211006073242.GA8404@kili
Fixes: 5036f0a0ec ("[SCSI] csiostor: Fix sparse warnings.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9583922563 ]
Commit a21d1becaa ("powerpc: Reintroduce is_kvm_guest() as a fast-path
check") added is_kvm_guest() and changed kvm_para_available() to use it.
is_kvm_guest() checks a static key, kvm_guest, and that static key is
set in check_kvm_guest().
The problem is check_kvm_guest() is only called on pseries, and even
then only in some configurations. That means is_kvm_guest() always
returns false on all non-pseries and some pseries depending on
configuration. That's a bug.
For PR KVM guests this is noticable because they no longer do live
patching of themselves, which can be detected by the omission of a
message in dmesg such as:
KVM: Live patching for a fast VM worked
To fix it make check_kvm_guest() an initcall, to ensure it's always
called at boot. It needs to be core so that it runs before
kvm_guest_init() which is postcore. To be an initcall it needs to return
int, where 0 means success, so update that.
We still call it manually in pSeries_smp_probe(), because that runs
before init calls are run.
Fixes: a21d1becaa ("powerpc: Reintroduce is_kvm_guest() as a fast-path check")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210623130514.2543232-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2719b26ae ]
While investigating a lockup at startup on Powerbook 3400C, it was
identified that the fbdev driver generates alignment exception at
startup:
--- interrupt: 600 at memset+0x60/0xc0
NIP: c0021414 LR: c03fc49c CTR: 00007fff
REGS: ca021c10 TRAP: 0600 Tainted: G W (5.14.2-pmac-00727-g12a41fa69492)
MSR: 00009032 <EE,ME,IR,DR,RI> CR: 44008442 XER: 20000100
DAR: cab80020 DSISR: 00017c07
GPR00: 00000007 ca021cd0 c14412e0 cab80000 00000000 00100000 cab8001c 00000004
GPR08: 00100000 00007fff 00000000 00000000 84008442 00000000 c0006fb4 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
GPR24: 00000000 81800000 00000320 c15fa400 c14d1878 00000000 c14d1800 c094e19c
NIP [c0021414] memset+0x60/0xc0
LR [c03fc49c] chipsfb_pci_init+0x160/0x580
--- interrupt: 600
[ca021cd0] [c03fc46c] chipsfb_pci_init+0x130/0x580 (unreliable)
[ca021d20] [c03a3a70] pci_device_probe+0xf8/0x1b8
[ca021d50] [c043d584] really_probe.part.0+0xac/0x388
[ca021d70] [c043d914] __driver_probe_device+0xb4/0x170
[ca021d90] [c043da18] driver_probe_device+0x48/0x144
[ca021dc0] [c043e318] __driver_attach+0x11c/0x1c4
[ca021de0] [c043ad30] bus_for_each_dev+0x88/0xf0
[ca021e10] [c043c724] bus_add_driver+0x190/0x22c
[ca021e40] [c043ee94] driver_register+0x9c/0x170
[ca021e60] [c0006c28] do_one_initcall+0x54/0x1ec
[ca021ed0] [c08246e4] kernel_init_freeable+0x1c0/0x270
[ca021f10] [c0006fdc] kernel_init+0x28/0x11c
[ca021f30] [c0017148] ret_from_kernel_thread+0x14/0x1c
Instruction dump:
7d4601a4 39490777 7d4701a4 39490888 7d4801a4 39490999 7d4901a4 39290aaa
7d2a01a4 4c00012c 4bfffe88 0fe00000 <4bfffe80> 9421fff0 38210010 48001970
This is due to 'dcbz' instruction being used on non-cached memory.
'dcbz' instruction is used by memset() to zeroize a complete
cacheline at once, and memset() is not expected to be used on non
cached memory.
When performing a 'sparse' check on fbdev driver, it also appears
that the use of memset() is unexpected:
drivers/video/fbdev/chipsfb.c:334:17: warning: incorrect type in argument 1 (different address spaces)
drivers/video/fbdev/chipsfb.c:334:17: expected void *
drivers/video/fbdev/chipsfb.c:334:17: got char [noderef] __iomem *screen_base
drivers/video/fbdev/chipsfb.c:334:15: warning: memset with byte count of 1048576
Use fb_memset() instead of memset(). fb_memset() is defined as
memset_io() for powerpc.
Fixes: 8c8709334c ("[PATCH] ppc32: Remove CONFIG_PMAC_PBOOK")
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/884a54f1e5cb774c1d9b4db780209bee5d4f6718.1631712563.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ed2f3545c ]
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fb ("driver/memory:Move Freescale IFC driver to a common driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
