[ Upstream commit 781d2a9a2f ]
We were checking validity of LVID entries only when getting
implementation use information from LVID in udf_sb_lvidiu(). However if
the LVID is suitably corrupted, it can cause problems also to code such
as udf_count_free() which doesn't use udf_sb_lvidiu(). So check validity
of LVID already when loading it from the disk and just disable LVID
altogether when it is not valid.
Reported-by: syzbot+7fbfe5fed73ebb675748@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe28140b33 ]
We should not clear FLAGS_DMA_ACTIVE before omap_sham_update_dma_stop() is
done calling dma_unmap_sg(). We already clear FLAGS_DMA_ACTIVE at the
end of omap_sham_update_dma_stop().
The early clearing of FLAGS_DMA_ACTIVE is not causing issues as we do not
need to defer anything based on FLAGS_DMA_ACTIVE currently. So this can be
applied as clean-up.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caa534c3ba ]
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df6313d707 ]
After calling dma_map_single(), we must also call dma_mapping_error().
This fixes the following warning when compiling with CONFIG_DMA_API_DEBUG:
[ 311.241478] WARNING: CPU: 0 PID: 428 at kernel/dma/debug.c:1027 check_unmap+0x79c/0x96c
[ 311.249547] DMA-API: mxs-dcp 2280000.crypto: device driver failed to check map error[device address=0x00000000860cb080] [size=32 bytes] [mapped as single]
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a729691b54 upstream.
When this platform was relatively new in November 2011, with early BIOS
revisions, a reboot quirk was added in commit 6be30bb7d7 ("x86/reboot:
Blacklist Dell OptiPlex 990 known to require PCI reboot")
However, this quirk (and several others) are open-ended to all BIOS
versions and left no automatic expiry if/when the system BIOS fixed the
issue, meaning that nobody is likely to come along and re-test.
What is really problematic with using PCI reboot as this quirk does, is
that it causes this platform to do a full power down, wait one second,
and then power back on. This is less than ideal if one is using it for
boot testing and/or bisecting kernels when legacy rotating hard disks
are installed.
It was only by chance that the quirk was noticed in dmesg - and when
disabled it turned out that it wasn't required anymore (BIOS A24), and a
default reboot would work fine without the "harshness" of power cycling the
machine (and disks) down and up like the PCI reboot does.
Doing a bit more research, it seems that the "newest" BIOS for which the
issue was reported[1] was version A06, however Dell[2] seemed to suggest
only up to and including version A05, with the A06 having a large number of
fixes[3] listed.
As is typical with a new platform, the initial BIOS updates come frequently
and then taper off (and in this case, with a revival for CPU CVEs); a
search for O990-A<ver>.exe reveals the following dates:
A02 16 Mar 2011
A03 11 May 2011
A06 14 Sep 2011
A07 24 Oct 2011
A10 08 Dec 2011
A14 06 Sep 2012
A16 15 Oct 2012
A18 30 Sep 2013
A19 23 Sep 2015
A20 02 Jun 2017
A23 07 Mar 2018
A24 21 Aug 2018
While it's overkill to flash and test each of the above, it would seem
likely that the issue was contained within A0x BIOS versions, given the
dates above and the dates of issue reports[4] from distros. So rather than
just throw out the quirk entirely, limit the scope to just those early BIOS
versions, in case people are still running systems from 2011 with the
original as-shipped early A0x BIOS versions.
[1] https://lore.kernel.org/lkml/1320373471-3942-1-git-send-email-trenn@suse.de/
[2] https://www.dell.com/support/kbdoc/en-ca/000131908/linux-based-operating-systems-stall-upon-reboot-on-optiplex-390-790-990-systems
[3] https://www.dell.com/support/home/en-ca/drivers/driversdetails?driverid=85j10
[4] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/768039
Fixes: 6be30bb7d7 ("x86/reboot: Blacklist Dell OptiPlex 990 known to require PCI reboot")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210530162447.996461-4-paul.gortmaker@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9655763b upstream.
This reverts commit f216562731.
[BUG]
It's no longer possible to create compressed inline extent after commit
f216562731 ("btrfs: compression: don't try to compress if we don't
have enough pages").
[CAUSE]
For compression code, there are several possible reasons we have a range
that needs to be compressed while it's no more than one page.
- Compressed inline write
The data is always smaller than one sector and the test lacks the
condition to properly recognize a non-inline extent.
- Compressed subpage write
For the incoming subpage compressed write support, we require page
alignment of the delalloc range.
And for 64K page size, we can compress just one page into smaller
sectors.
For those reasons, the requirement for the data to be more than one page
is not correct, and is already causing regression for compressed inline
data writeback. The idea of skipping one page to avoid wasting CPU time
could be revisited in the future.
[FIX]
Fix it by reverting the offending commit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Link: https://lore.kernel.org/linux-btrfs/afa2742.c084f5d6.17b6b08dffc@tnonline.net
Fixes: f216562731 ("btrfs: compression: don't try to compress if we don't have enough pages")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad69832f3 upstream.
When we free a page whose order is very close to MAX_ORDER and greater
than pageblock_order, it wastes some CPU cycles to increase max_order to
MAX_ORDER one by one and check the pageblock migratetype of that page
repeatedly especially when MAX_ORDER is much larger than pageblock_order.
We also should not be checking migratetype of buddy when "order ==
MAX_ORDER - 1" as the buddy pfn may be invalid, so adjust the condition.
With the new check, we don't need the max_order check anymore, so we
replace it.
Also adjust max_order initialization so that it's lower by one than
previously, which makes the code hopefully more clear.
Link: https://lkml.kernel.org/r/20201204155109.55451-1-songmuchun@bytedance.com
Fixes: d9dddbf556 ("mm/page_alloc: prevent merging between isolated and other pageblocks")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 968339fad4 upstream.
.globl sets the symbol binding to STB_GLOBAL while .weak sets the
binding to STB_WEAK. GNU as let .weak override .globl since
binutils-gdb 5ca547dc2399a0a5d9f20626d4bf5547c3ccfddd (1996). Clang
integrated assembler let the last win but it may error in the future.
Since it is a convention that only one binding directive is used, just
delete .globl.
Fixes: ee9d21b3b3 ("powerpc/boot: Ensure _zimage_start is a weak symbol")
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200325164257.170229-1-maskray@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fb0a2c989 upstream.
The comment here is wrong, the addi reads from r2 not r12. The code is
correct, 0x38420000 = addi r2,r2,0.
Fixes: a61674bdfc ("powerpc/module: Handle R_PPC64_ENTRY relocations")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8fbdc2bc4 upstream.
SEC1 doesn't support SHA384/512, so it doesn't require
longer keys.
This patch reduces the max key size when the driver
is built for SEC1 only.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 03d2c5114c ("crypto: talitos - Extend max key length for SHA384/512-HMAC and AEAD")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26f4e759ef upstream.
176.718956 Krnl Code: 00000000004d38b0: a54c0018 llihh %r4,24
176.718956 00000000004d38b4: b9080014 agr %r1,%r4
^
Using a tab to align disassembly lines which follow the first line with
"Krnl Code: " doesn't always work, e.g. if there is a prefix (timestamp
or syslog prefix) which is not 8 chars aligned. Go back to alignment
with spaces.
Fixes: b192571d1a ("s390/disassembler: increase show_code buffer size")
Signed-off-by: Vasily Gorbik <gor@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1e84eb58e upstream.
As per RFC792, ICMP errors should be sent to the source host.
However, in configurations with Virtual Routing and Forwarding tables,
looking up which routing table to use is currently done by using the
destination net_device.
commit 9d1a6c4ea4 ("net: icmp_route_lookup should use rt dev to
determine L3 domain") changes the interface passed to
l3mdev_master_ifindex() and inet_addr_type_dev_table() from skb_in->dev
to skb_dst(skb_in)->dev. This effectively uses the destination device
rather than the source device for choosing which routing table should be
used to lookup where to send the ICMP error.
Therefore, if the source and destination interfaces are within separate
VRFs, or one in the global routing table and the other in a VRF, looking
up the source host in the destination interface's routing table will
fail if the destination interface's routing table contains no route to
the source host.
One observable effect of this issue is that traceroute does not work in
the following cases:
- Route leaking between global routing table and VRF
- Route leaking between VRFs
Preferably use the source device routing table when sending ICMP error
messages. If no source device is set, fall-back on the destination
device routing table. Else, use the main routing table (index 0).
[ It has been pointed out that a similar issue may exist with ICMP
errors triggered when forwarding between network namespaces. It would
be worthwhile to investigate, but is outside of the scope of this
investigation. ]
[ It has also been pointed out that a similar issue exists with
unreachable / fragmentation needed messages, which can be triggered by
changing the MTU of eth1 in r1 to 1400 and running:
ip netns exec h1 ping -s 1450 -Mdo -c1 172.16.2.2
Some investigation points to raw_icmp_error() and raw_err() as being
involved in this last scenario. The focus of this patch is TTL expired
ICMP messages, which go through icmp_route_lookup.
Investigation of failure modes related to raw_icmp_error() is beyond
this investigation's scope. ]
Fixes: 9d1a6c4ea4 ("net: icmp_route_lookup should use rt dev to determine L3 domain")
Link: https://tools.ietf.org/html/rfc792
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 914cea93dd upstream.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__gfs2_set_acl() into gfs2_set_acl(). That way the function will not be
called when inheriting ACLs which is what we want as it prevents SGID
bit clearing and the mode has been properly set by posix_acl_create()
anyway.
Fixes: 073931017b
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c843455975 upstream.
We currently rely on runtime PM to enable dedicated wakeirq for suspend.
This assumption fails in the following two cases:
1. If the consumer driver does not have runtime PM implemented, the
dedicated wakeirq never gets enabled for suspend
2. If the consumer driver has runtime PM implemented, but does not idle
in suspend
Let's fix the issue by always enabling the dedicated wakeirq during
suspend.
Depends-on: bed570307e (PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend)
Fixes: 4990d4fe32 (PM / Wakeirq: Add automated device wake IRQ handling)
Reported-by: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[ tony@atomide.com: updated based on bed570307e, added description ]
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 161a582bd1 upstream.
clang static analysis reports this problem
mos7720.c:352:2: warning: Undefined or garbage value returned to caller
return d;
^~~~~~~~
In the parport_mos7715_read_data()'s call to read_mos_reg(), 'd' is
only set after the alloc block.
buf = kmalloc(1, GFP_KERNEL);
if (!buf)
return -ENOMEM;
Although the problem is reported in parport_most7715_read_data(),
none of the callee's of read_mos_reg() check the return status.
Make sure to clear the return-value buffer also on allocation failures.
Fixes: 0d130367ab ("USB: serial: mos7720: fix control-message error handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210111220904.1035957-1-trix@redhat.com
[ johan: only clear the buffer on errors, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7f12a21f6 upstream.
Commit fd567653bd ("usb: phy: isp1301: Add OF device ID table")
added an OF device ID table, but used the of_match_ptr() macro
that will lead to a build warning if CONFIG_OF symbol is disabled:
drivers/usb/phy//phy-isp1301.c:36:34: warning: ‘isp1301_of_match’ defined but not used [-Wunused-const-variable=]
static const struct of_device_id isp1301_of_match[] = {
^~~~~~~~~~~~~~~~
Fixes: fd567653bd ("usb: phy: isp1301: Add OF device ID table")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 514e976744 upstream.
My local syzbot instance hit memory leak in usb_set_configuration().
The problem was in unputted usb interface. In case of errors after
usb_get_intf() the reference should be putted to correclty free memory
allocated for this interface.
Fixes: ec16dae545 ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca2848022c upstream.
Do not delete a key cache entry that is still being referenced by
pending frames in TXQs. This avoids reuse of the key cache entry while a
frame might still be transmitted using it.
To avoid having to do any additional operations during the main TX path
operations, track pending key cache entries in a new bitmap and check
whether any pending entries can be deleted before every new key
add/remove operation. Also clear any remaining entries when stopping the
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-6-jouni@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 144cd24dbc upstream.
tkip_keymap can be used internally to avoid the reference to key->cipher
and with this, only the key index value itself is needed. This allows
ath_key_delete() call to be postponed to be handled after the upper
layer STA and key entry have already been removed. This is needed to
make ath9k key cache management safer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-5-jouni@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56c5485c9e upstream.
It is possible for there to be pending frames in TXQs with a reference
to the key cache entry that is being deleted. If such a key cache entry
is cleared, those pending frame in TXQ might get transmitted without
proper encryption. It is safer to leave the previously used key into the
key cache in such cases. Instead, only clear the MAC address to prevent
RX processing from using this key cache entry.
This is needed in particularly in AP mode where the TXQs cannot be
flushed on station disconnection. This change alone may not be able to
address all cases where the key cache entry might get reused for other
purposes immediately (the key cache entry should be released for reuse
only once the TXQs do not have any remaining references to them), but
this makes it less likely to get unprotected frames and the more
complete changes may end up being significantly more complex.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-2-jouni@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb033c95c9 upstream.
The system currently warns if the config conditions for
building return_address in arch/arm/kernel/return_address.c
are not met, leaving just an EXPORT_SYMBOL_GPL(return_address)
of a function defined to be 'static linline'.
This is a result of aeea3592a1 ("ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h").
Since we're not going to build anything other than an exported
symbol for something that is already being defined to be an
inline-able return of NULL, just avoid building the code to
remove the following warning:
Fixes: aeea3592a1 ("ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h")
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 222013f9ac ]
Support for cryptoloop has been officially marked broken and deprecated
in favor of dm-crypt (which supports the same broken algorithms if
needed) in Linux 2.6.4 (released in March 2004), and support for it has
been entirely removed from losetup in util-linux 2.23 (released in April
2013). Add a warning and a deprecation schedule.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210827163250.255325-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e543468869 ]
Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0cd08537d ]
For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a54c4613da upstream.
The location of the system.data extended attribute can change whenever
xattr_sem is not taken. So we need to recalculate the i_inline_off
field since it mgiht have changed between ext4_write_begin() and
ext4_write_end().
This means that caching i_inline_off is probably not helpful, so in
the long run we should probably get rid of it and shrink the in-memory
ext4 inode slightly, but let's fix the race the simple way for now.
Cc: stable@kernel.org
Fixes: f19d5870cb ("ext4: add normal write support for inline data")
Reported-by: syzbot+13146364637c7363a7de@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to hold the sock_tag_list_lock while accessing the tag to
avoid a race between getting the tag and free'ing the tag.
Bug: 184018316
Fixes: c7ca0ac69702 ("ANDROID: netfilter: xt_qtaguid: add qtaguid matching module")
Signed-off-by: Will McVicker <willmcvicker@google.com>
Change-Id: I62404bdaa602586e00821a7d4c5f9b9868a0e90a
commit 112022bdb5 upstream
Mark NX as being used for all non-nested shadow MMUs, as KVM will set the
NX bit for huge SPTEs if the iTLB mutli-hit mitigation is enabled.
Checking the mitigation itself is not sufficient as it can be toggled on
at any time and KVM doesn't reset MMU contexts when that happens. KVM
could reset the contexts, but that would require purging all SPTEs in all
MMUs, for no real benefit. And, KVM already forces EFER.NX=1 when TDP is
disabled (for WP=0, SMEP=1, NX=0), so technically NX is never reserved
for shadow MMUs.
Fixes: b8e8c8303f ("kvm: mmu: ITLB_MULTIHIT mitigation")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622175739.3610207-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sudip: use old path and adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb4b1373dc ]
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
Simply put: Linux 5.11 and later.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/60efc69f-1f35-529d-a7ef-da0549cad143@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e74cfa91f4 ]
As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60f0779862 ]
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210721142648.1525924-2-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 359f4cdd7d ]
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
