Executing reboot command several times on the machine "Dell
PowerEdge R740", UEFI security detection stopped machine
with the following prompt:
UEFI0082: The system was reset due to a timeout from the watchdog
timer. Check the System Event Log (SEL) or crash dumps from
Operating Sysstem to identify the source that triggered the
watchdog timer reset. Update the firmware or driver for the
identified device.
iDRAC has warning event: "The watchdog timer reset the system".
This patch fixes this issue by adding the reboot notifier.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650984810-6247-3-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This ensures that the same value is read back as was eventually
programmed when using seconds as accuracy. Even then, comparing the more
precise heartbeat_ms against heartbeat in seconds will almost never
provide a match and will needlessly raise a warning. Fix by comparing
apples to apples.
Tested in combination with U-Boot as watchdog starter.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/6a4b54ac-9588-e172-c4c7-b91d524a851e@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Most Allwinner SoCs have just one input clock to drive the watchdog
peripheral. So far this is the 24 MHz "HOSC" oscillator, divided down
internally to 32 KHz.
The F1C100 series watchdog however uses the unchanged 32 KHz "LOSC" as
its only clock input, which has the same effect, but let's the binding
description mismatch.
Change the binding description to name the clocks more loosely, so both
the LOSC and divided HOSC match the description. As the fixed clock names
now make less sense, drop them from SoCs supporting just one clock
input, they were not used by any DT anyway.
For the newer SoCs, supporting a choice of two input clocks, we keep
both the description and clock-names requirement.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220317162349.739636-3-andre.przywara@arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch uses the force reset(WDTRSTB) for triggering WDT reset for
restart callback. This method(ie, Generate Reset (WDTRSTB) Signal on
parity error)is faster compared to the overflow method for triggering
watchdog reset.
Overflow method:
reboot: Restarting system
Reboot failed -- System halted
NOTICE: BL2: v2.5(release):v2.5/rzg2l-1.00-27-gf48f1440c
Parity error method:
reboot: Restarting system
NOTICE: BL2: v2.5(release):v2.5/rzg2l-1.00-27-gf48f1440c
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220225175320.11041-7-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Both rzg2l_wdt_probe() and rzg2l_wdt_start() calls reset_control_
deassert() which results in a reset control imbalance.
This patch fixes reset control imbalance by removing reset_control_
deassert() from rzg2l_wdt_start() and replaces reset_control_assert with
reset_control_reset in rzg2l_wdt_stop() as watchdog module can be stopped
only by a module reset. This change will allow us to restart WDT after
stop() by configuring WDT timeout and enable registers.
Fixes: 2cbc5cd0b5 ("watchdog: Add Watchdog Timer driver for RZ/G2L")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220225175320.11041-5-biju.das.jz@bp.renesas.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Parse compatible as expected for modern QCOMs.
Fixes warnings as:
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: watchdog@17980000: compatible: ['qcom,apss-wdt-sdm845', 'qcom,kpss-wdt'] is too long
From schema: Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: watchdog@17980000: compatible: Additional items are not allowed ('qcom,kpss-wdt' was unexpected)
From schema: Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220111212310.97566-1-david@ixit.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Take care of faults occuring between the PARange and IPA range by
injecting an exception
- Fix S2 faults taken from a host EL0 in protected mode
- Work around Oops caused by a PMU access from a 32bit guest when PMU
has been created. This is a temporary bodge until we fix it for
good.
x86:
- Fix potential races when walking host page table
- Fix shadow page table leak when KVM runs nested
- Work around bug in userspace when KVM synthesizes leaf 0x80000021
on older (pre-EPYC) or Intel processors
Generic (but affects only RISC-V):
- Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: work around QEMU issue with synthetic CPUID leaves
Revert "x86/mm: Introduce lookup_address_in_mm()"
KVM: x86/mmu: fix potential races when walking host page table
KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDR
KVM: arm64: Inject exception on out-of-IPA-range translation fault
KVM/arm64: Don't emulate a PMU for 32-bit guests if feature not set
KVM: arm64: Handle host stage-2 faults from 32-bit EL0
Pull x86 fixes from Borislav Petkov:
- A fix to disable PCI/MSI[-X] masking for XEN_HVM guests as that is
solely controlled by the hypervisor
- A build fix to make the function prototype (__warn()) as visible as
the definition itself
- A bunch of objtool annotation fixes which have accumulated over time
- An ORC unwinder fix to handle bad input gracefully
- Well, we thought the microcode gets loaded in time in order to
restore the microcode-emulated MSRs but we thought wrong. So there's
a fix for that to have the ordering done properly
- Add new Intel model numbers
- A spelling fix
* tag 'x86_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guests
bug: Have __warn() prototype defined unconditionally
x86/Kconfig: fix the spelling of 'becoming' in X86_KERNEL_IBT config
objtool: Use offstr() to print address of missing ENDBR
objtool: Print data address for "!ENDBR" data warnings
x86/xen: Add ANNOTATE_NOENDBR to startup_xen()
x86/uaccess: Add ENDBR to __put_user_nocheck*()
x86/retpoline: Add ANNOTATE_NOENDBR for retpolines
x86/static_call: Add ANNOTATE_NOENDBR to static call trampoline
objtool: Enable unreachable warnings for CLANG LTO
x86,objtool: Explicitly mark idtentry_body()s tail REACHABLE
x86,objtool: Mark cpu_startup_entry() __noreturn
x86,xen,objtool: Add UNWIND hint
lib/strn*,objtool: Enforce user_access_begin() rules
MAINTAINERS: Add x86 unwinding entry
x86/unwind/orc: Recheck address range after stack info was updated
x86/cpu: Load microcode during restore_processor_state()
x86/cpu: Add new Alderlake and Raptorlake CPU model numbers
Pull objtool fixes from Borislav Petkov:
"A bunch of objtool fixes to improve unwinding, sibling call detection,
fallthrough detection and relocation handling of weak symbols when the
toolchain strips section symbols"
* tag 'objtool_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix code relocs vs weak symbols
objtool: Fix type of reloc::addend
objtool: Fix function fallthrough detection for vmlinux
objtool: Fix sibling call detection in alternatives
objtool: Don't set 'jump_dest' for sibling calls
x86/uaccess: Don't jump between functions
Pull driver core fixes from Greg KH:
"Here are some small driver core and kernfs fixes for some reported
problems. They include:
- kernfs regression that is causing oopses in 5.17 and newer releases
- topology sysfs fixes for a few small reported problems.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: fix NULL dereferencing in kernfs_remove
topology: Fix up build warning in topology_is_visible()
arch_topology: Do not set llc_sibling if llc_id is invalid
topology: make core_mask include at least cluster_siblings
topology/sysfs: Hide PPIN on systems that do not support it.
Pull char/misc driver fixes from Greg KH:
"Here are a small number of char/misc/other driver fixes for 5.18-rc5
Nothing major in here, this is mostly IIO driver fixes along with some
other small things:
- at25 driver fix for systems without a dma-able stack
- phy driver fixes for reported issues
- binder driver fixes for reported issues
All of these have been in linux-next without any reported problems"
* tag 'char-misc-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (31 commits)
eeprom: at25: Use DMA safe buffers
binder: Gracefully handle BINDER_TYPE_FDA objects with num_fds=0
binder: Address corner cases in deferred copy and fixup
phy: amlogic: fix error path in phy_g12a_usb3_pcie_probe()
iio: imu: inv_icm42600: Fix I2C init possible nack
iio: dac: ltc2688: fix voltage scale read
interconnect: qcom: sdx55: Drop IP0 interconnects
interconnect: qcom: sc7180: Drop IP0 interconnects
phy: ti: Add missing pm_runtime_disable() in serdes_am654_probe
phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe
phy: ti: omap-usb2: Fix error handling in omap_usb2_enable_clocks
bus: mhi: host: pci_generic: Flush recovery worker during freeze
bus: mhi: host: pci_generic: Add missing poweroff() PM callback
phy: ti: tusb1210: Fix an error handling path in tusb1210_probe()
phy: samsung: exynos5250-sata: fix missing device put in probe error paths
phy: samsung: Fix missing of_node_put() in exynos_sata_phy_probe
phy: ti: Fix missing of_node_put in ti_pipe3_get_sysctrl()
phy: ti: tusb1210: Make tusb1210_chg_det_states static
iio:dac:ad3552r: Fix an IS_ERR() vs NULL check
iio: sx9324: Fix default precharge internal resistance register
...
Pull tty/serial fixes from Greg KH:
"Here are some small serial driver fixes, and a larger number of GSM
line discipline fixes for 5.18-rc5.
These include:
- lots of tiny n_gsm fixes for issues to resolve a number of reported
problems. Seems that people are starting to actually use this code
again.
- 8250 driver fixes for some devices
- imx serial driver fix
- amba-pl011 driver fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (27 commits)
tty: n_gsm: fix sometimes uninitialized warning in gsm_dlci_modem_output()
serial: 8250: Correct the clock for EndRun PTP/1588 PCIe device
serial: 8250: Also set sticky MCR bits in console restoration
tty: n_gsm: fix software flow control handling
tty: n_gsm: fix invalid use of MSC in advanced option
tty: n_gsm: fix broken virtual tty handling
Revert "serial: sc16is7xx: Clear RS485 bits in the shutdown"
tty: n_gsm: fix missing update of modem controls after DLCI open
serial: 8250: Fix runtime PM for start_tx() for empty buffer
serial: imx: fix overrun interrupts in DMA mode
serial: amba-pl011: do not time out prematurely when draining tx fifo
tty: n_gsm: fix incorrect UA handling
tty: n_gsm: fix reset fifo race condition
tty: n_gsm: fix missing tty wakeup in convergence layer type 2
tty: n_gsm: fix wrong signal octets encoding in MSC
tty: n_gsm: fix wrong command frame length field encoding
tty: n_gsm: fix wrong command retry handling
tty: n_gsm: fix missing explicit ldisc flush
tty: n_gsm: fix wrong DLCI release order
tty: n_gsm: fix insufficient txframe size
...
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.18-rc5 for some
reported issues and new quirks. They include:
- dwc3 driver fixes
- xhci driver fixes
- typec driver fixes
- new usb-serial driver ids
- added new USB devices to existing quirk tables
- other tiny fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (31 commits)
usb: phy: generic: Get the vbus supply
usb: dwc3: gadget: Return proper request status
usb: dwc3: pci: add support for the Intel Meteor Lake-P
usb: dwc3: core: Only handle soft-reset in DCTL
usb: gadget: configfs: clear deactivation flag in configfs_composite_unbind()
usb: misc: eud: Fix an error handling path in eud_probe()
usb: core: Don't hold the device lock while sleeping in do_proc_control()
usb: dwc3: Try usb-role-switch first in dwc3_drd_init
usb: dwc3: core: Fix tx/rx threshold settings
usb: mtu3: fix USB 3.0 dual-role-switch from device to host
xhci: Enable runtime PM on second Alderlake controller
usb: dwc3: fix backwards compat with rockchip devices
dt-bindings: usb: samsung,exynos-usb2: add missing required reg
usb: misc: fix improper handling of refcount in uss720_probe()
USB: Fix ehci infinite suspend-resume loop issue in zhaoxin
usb: typec: tcpm: Fix undefined behavior due to shift overflowing the constant
usb: typec: rt1719: Fix build error without CONFIG_POWER_SUPPLY
usb: typec: ucsi: Fix role swapping
usb: typec: ucsi: Fix reuse of completion structure
usb: xhci: tegra:Fix PM usage reference leak of tegra_xusb_unpowergate_partitions
...
Pull SCSI fix from James Bottomley:
"One fix for an endless error loop with the target driver affecting
tapes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: pscsi: Set SCF_TREAT_READ_AS_NORMAL flag only if there is valid data
Pull ARM SoC fixes from Arnd Bergmann:
- A fix for a regression caused by the previous set of bugfixes
changing tegra and at91 pinctrl properties.
More work is needed to figure out what this should actually be, but a
revert makes it work for the moment.
- Defconfig regression fixes for tegra after renamed symbols
- Build-time warning and static checker fixes for imx, op-tee, sunxi,
meson, at91, and omap
- More at91 DT fixes for audio, regulator and spi nodes
- A regression fix for Renesas Hyperflash memory probe
- A stability fix for amlogic boards, modifying the allowed cpufreq
states
- Multiple fixes for system suspend on omap2+
- DT fixes for various i.MX bugs
- A probe error fix for imx6ull-colibri MMC
- A MAINTAINERS file entry for samsung bug reports
* tag 'soc-fixes-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
Revert "arm: dts: at91: Fix boolean properties with values"
bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
Revert "arm64: dts: tegra: Fix boolean properties with values"
arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
ARM: dts: imx6ull-colibri: fix vqmmc regulator
MAINTAINERS: add Bug entry for Samsung and memory controller drivers
memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual Mode
ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
ARM: dts: am3517-evm: Fix misc pinmuxing
ARM: dts: am33xx-l4: Add missing touchscreen clock properties
ARM: dts: Fix mmc order for omap3-gta04
ARM: dts: at91: fix pinctrl phandles
ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
ARM: dts: at91: Describe regulators on at91sam9g20ek
ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
ARM: dts: at91: Fix boolean properties with values
ARM: dts: at91: use generic node name for dataflash
ARM: dts: at91: align SPI NOR node name with dtschema
ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
...
Pull clk fixes from Stephen Boyd:
"A semi-large pile of clk driver fixes this time around.
Nothing is touching the core so these fixes are fairly well contained
to specific devices that use these clk drivers.
- Some Allwinner SoC fixes to gracefully handle errors and mark an
RTC clk as critical so that the RTC keeps ticking.
- Fix AXI bus clks and RTC clk design for Microchip PolarFire SoC
driver introduced this cycle. This has some devicetree bits acked
by riscv maintainers. We're fixing it now so that the prior
bindings aren't released in a major kernel version.
- Remove a reset on Microchip PolarFire SoCs that broke when enabling
CONFIG_PM.
- Set a min/max for the Qualcomm graphics clk. This got broken by the
clk rate range patches introduced this cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()
clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical
riscv: dts: microchip: reparent mpfs clocks
clk: microchip: mpfs: add RTCREF clock control
clk: microchip: mpfs: re-parent the configurable clocks
dt-bindings: rtc: add refclk to mpfs-rtc
dt-bindings: clk: mpfs: add defines for two new clocks
dt-bindings: clk: mpfs document msspll dri registers
riscv: dts: microchip: fix usage of fic clocks on mpfs
clk: microchip: mpfs: mark CLK_ATHENA as critical
clk: microchip: mpfs: fix parents for FIC clocks
clk: qcom: clk-rcg2: fix gfx3d frequency calculation
clk: microchip: mpfs: don't reset disabled peripherals
clk: sunxi-ng: fix not NULL terminated coccicheck error
Pull block fixes from Jens Axboe:
- Revert of a patch that caused timestamp issues (Tejun)
- iocost warning fix (Tejun)
- bfq warning fix (Jan)
* tag 'block-5.18-2022-04-29' of git://git.kernel.dk/linux-block:
bfq: Fix warning in bfqq_request_over_limit()
Revert "block: inherit request start time from bio for BLK_CGROUP"
iocost: don't reset the inuse weight of under-weighted debtors
Pull io_uring fixes from Jens Axboe:
"Pretty boring:
- three patches just adding reserved field checks (me, Eugene)
- Fixing a potential regression with IOPOLL caused by a block change
(Joseph)"
Boring is good.
* tag 'io_uring-5.18-2022-04-29' of git://git.kernel.dk/linux-block:
io_uring: check that data field is 0 in ringfd unregister
io_uring: fix uninitialized field in rw io_kiocb
io_uring: check reserved fields for recv/recvmsg
io_uring: check reserved fields for send/sendmsg
Pull random number generator fixes from Jason Donenfeld:
- Eric noticed that the memmove() in crng_fast_key_erasure() was bogus,
so this has been changed to a memcpy() and the confusing situation
clarified with a detailed comment.
- [Half]SipHash documentation updates from Bagas and Eric, after Eric
pointed out that the use of HalfSipHash in random.c made a bit of the
text potentially misleading.
* tag 'random-5.18-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
Documentation: siphash: disambiguate HalfSipHash algorithm from hsiphash functions
Documentation: siphash: enclose HalfSipHash usage example in the literal block
Documentation: siphash: convert danger note to warning for HalfSipHash
random: document crng_fast_key_erasure() destination possibility
