[ Upstream commit 58577966a4 ]
Currently the DT for QCS404 SoC has setup for 2 USB2 PHYs with one each
assigned to USB3 controller and USB2 controller. This assignment is
incorrect which only works by luck: as when each USB HCI comes up it
configures the *other* controllers PHY which is enough to make them
happy. If, for any reason, we were to disable one of the controllers then
both would stop working.
This was a difficult inconsistency to be caught which was found while
trying to enable USB support in u-boot. So with all the required drivers
ported to u-boot, I couldn't get the same USB storage device enumerated
in u-boot which was being enumerated fine by the kernel.
The root cause of the problem came out to be that I wasn't enabling USB2
PHY: "usb2_phy_prim" in u-boot. Then I realised that via simply disabling
the same USB2 PHY currently assigned to USB2 host controller in the
kernel disabled enumeration for USB3 host controller as well.
So fix this inconsistency by correctly assigning USB2 PHYs.
Fixes: 9375e7d719 ("arm64: dts: qcom: qcs404: Add USB devices and PHYs")
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220711083038.1518529-1-sumit.garg@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b415bb7c97 ]
Hook SDMMC1 CD up with CVM GPIO02 (SOC_GPIO11) used for card detection on J4
(uSD socket) on the carrier.
Fixes: ef633bfc21 ("arm64: tegra: Enable card detect for SD card on P2888")
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c98e6e6836 ]
The bananapi R64 (BPI-R64) experiences wrong WPS button signals.
In OpenWrt pushing the WPS button while powering on the device will set
it to recovery mode. Currently, this also happens without any user
interaction. In particular, the wrong signals appear while booting the
device or restarting it, e.g. after doing a system upgrade. If the
device is in recovery mode the user needs to manually power cycle or
restart it.
The official BPI-R64 sources set the WPS button to GPIO_ACTIVE_LOW in
the device tree. This setting seems to suppress the unwanted WPS button
press signals. So this commit changes the button from GPIO_ACTIVE_HIGH to
GPIO_ACTIVE_LOW.
The official BPI-R64 sources can be found on
https://github.com/BPI-SINOVOIP/BPI-R64-openwrt
Fixes: 0b6286dd96 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://lore.kernel.org/r/20220630111746.4098-1-vincent@systemli.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54872fea6a ]
In error case in hisi_lpc_acpi_probe() after calling platform_device_add(),
hisi_lpc_acpi_remove() can't release the failed 'pdev', so it will be leak,
call platform_device_put() to fix this problem.
I'v constructed this error case and tested this patch on D05 board.
Fixes: 99c0228d6f ("HISI LPC: Re-Add ACPI child enumeration support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6e0951414 ]
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
When breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the child node.
Add missing of_node_put() to avoid refcount leak.
Fixes: 05589b30b2 ("soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220606064252.42595-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b13a3e5fd4 ]
When a platform marks a memory range as "special purpose" it is not
onlined as System RAM by default. However, it is still suitable for
error injection. Add IORES_DESC_SOFT_RESERVED to einj_error_inject() as
a permissible memory type in the sanity checking of the arguments to
_EINJ.
Fixes: 262b45ae3a ("x86/efi: EFI soft reservation to E820 enumeration")
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reported-by: Omar Avelar <omar.avelar@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8977917e1 ]
The PM8916 device specification [1] documents a programmable range of
1.75V to 3.337V with 12.5mV steps for the PMOS LDOs in PM8916. This
range is also used when controlling the regulator directly using the
qcom_spmi-regulator driver ("ult_pldo" there).
However, for some reason the qcom_smd-regulator driver allows a much
larger range for the same hardware component. This could be simply a
typo, since the start of the range is essentially just missing a '1'.
In practice this does not cause any major problems, since the driver
just sends the actual voltage to the RPM firmware instead of making use
of the incorrect voltage selector. Still, having the wrong range there
is confusing and prevents the regulator core from validating requests
correctly.
[1]: https://developer.qualcomm.com/download/sd410/pm8916pm8916-1-power-management-ic-device-specification.pdf
Fixes: 57d6567680 ("regulator: qcom-smd: Add PM8916 support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Link: https://lore.kernel.org/r/20220623094614.1410180-2-stephan.gerhold@kernkonzept.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942228fbf5 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 1e037794f7 ("ARM: OMAP3+: PRM: register interrupt information from DT")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220526073724.21169-1-linmq006@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9705db1eff ]
omapdss_find_dss_of_node() calls of_find_compatible_node() to get device
node. of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() in later error path and normal path.
Fixes: e0c827aca0 ("drm/omap: Populate DSS children in omapdss driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220601044858.3352-1-linmq006@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b82d9fa257 ]
Returning 0 early from __bio_iov_append_get_pages() for the
max_append_sectors warning just creates an infinite loop since 0 means
success, and the bio will never fill from the unadvancing iov_iter. We
could turn the return into an error value, but it will already be turned
into an error value later on, so just remove the warning. Clearly no one
ever hit it anyway.
Fixes: 0512a75b98 ("block: Introduce REQ_OP_ZONE_APPEND")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220610195830.3574005-2-kbusch@fb.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab3f045774 ]
If both the model and the compatible properties are missing, then
machine will not be set. Initialize it with NULL.
Fixes: 34c1c21e94 ("soc: fsl: fix section mismatch build warnings")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eae6d58d67 ]
Commit dfd5e3f5fe ("locking/lockdep: Mark local_lock_t") added yet
another lockdep_init_map_*() variant, but forgot to update all the
existing users of the most complicated version.
This could lead to a loss of lock_type and hence an incorrect report.
Given the relative rarity of both local_lock and these annotations,
this is unlikely to happen in practise, still, best fix things.
Fixes: dfd5e3f5fe ("locking/lockdep: Mark local_lock_t")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YqyEDtoan20K0CVD@worktop.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 506506cad3 ]
Commit b20d1ba3cf ("arm64: cpufeature: allow for version discrepancy in
PMU implementations") made it possible to run Linux on a machine with PMUs
with different versions without tainting the kernel. The patch relaxed the
restriction only for the ID_AA64DFR0_EL1.PMUVer field, and missed doing the
same for ID_DFR0_EL1.PerfMon , which also reports the PMU version, but for
the AArch32 state.
For example, with Linux running on two clusters with different PMU
versions, the kernel is tainted when bringing up secondaries with the
following message:
[ 0.097027] smp: Bringing up secondary CPUs ...
[..]
[ 0.142805] Detected PIPT I-cache on CPU4
[ 0.142805] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_DFR0_EL1. Boot CPU: 0x00000004011088, CPU4: 0x00000005011088
[ 0.143555] CPU features: Unsupported CPU feature variation detected.
[ 0.143702] GICv3: CPU4: found redistributor 10000 region 0:0x000000002f180000
[ 0.143702] GICv3: CPU4: using allocated LPI pending table @0x00000008800d0000
[ 0.144888] CPU4: Booted secondary processor 0x0000010000 [0x410fd0f0]
The boot CPU implements FEAT_PMUv3p1 (ID_DFR0_EL1.PerfMon, bits 27:24, is
0b0100), but CPU4, part of the other cluster, implements FEAT_PMUv3p4
(ID_DFR0_EL1.PerfMon = 0b0101).
Treat the PerfMon field as FTR_NONSTRICT and FTR_EXACT to pass the sanity
check and to match how PMUVer is treated for the 64bit ID register.
Fixes: b20d1ba3cf ("arm64: cpufeature: allow for version discrepancy in PMU implementations")
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20220617111332.203061-1-alexandru.elisei@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62e8a53431 ]
"make dtbs_check":
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[74], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[79], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874-idk-2121wr.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[82], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874-mipi-2.1.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[87], [0]] is too long
arch/arm64/boot/dts/renesas/r8a77990-ebisu.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[105], [0]] is too long
From schema: Documentation/devicetree/bindings/thermal/thermal-zones.yaml
Indeed, the thermal sensors on R-Car E3 and RZ/G2E support only a single
zone, hence #thermal-sensor-cells = <0>.
Fix this by dropping the bogus zero cell from the thermal sensor
specifiers.
Fixes: 8fa7d18f9e ("arm64: dts: renesas: r8a77990: Create thermal zone to support IPA")
Fixes: 8438bfda9d ("arm64: dts: renesas: r8a774c0: Create thermal zone to support IPA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/28b812fdd1fc3698311fac984ab8b91d3d655c1c.1655301684.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit feedaacdad ]
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 409dfdcaff ]
Commit 6727ad9e20 ("nmi_backtrace: generate one-line reports for idle cpus")
introduced a new text section called cpuidle; with that, we have a mechanism
to add idling functions in such section and skip them from nmi_backtrace
output, since they're useless and potentially flooding for such report.
Happens that inlining might cause some real idle functions to end-up
outside of such section; this is currently the case of ACPI processor_idle
driver; the functions acpi_idle_enter_* do inline acpi_idle_do_entry(),
hence they stay out of the cpuidle section.
Fix that by marking such functions to also live in the cpuidle section.
Fixes: 6727ad9e20 ("nmi_backtrace: generate one-line reports for idle cpus")
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb23389a24 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b8eb35fd59 ("ARM: bcm281xx: Add L2 cache enable code")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec85bd369f ]
When offset is larger than the size of the bit array, we should not
attempt to access the array as we can perform an access beyond the
end of the array. Fix this by changing the pre-condition.
Using "cmp r2, r1; bhs ..." covers us for the size == 0 case, since
this will always take the branch when r1 is zero, irrespective of
the value of r2. This means we can fix this bug without adding any
additional code!
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b620aa3a7b ]
RSPI IP on RZ/{A, G2L} SoC's has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked.
PIO fallback does not work as interrupt signal is disabled.
This patch fixes this issue by re-enabling the interrupts by
calling dmaengine_synchronize().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220721143449.879257-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be640317a1 ]
With GCC 12 allmodconfig prom_init fails to build:
Error: External symbol 'memset' referenced from prom_init.c
make[2]: *** [arch/powerpc/kernel/Makefile:204: arch/powerpc/kernel/prom_init_check] Error 1
The allmodconfig build enables KASAN, so all calls to memset in
prom_init should be converted to __memset by the #ifdefs in
asm/string.h, because prom_init must use the non-KASAN instrumented
versions.
The build failure happens because there's a call to memset that hasn't
been caught by the pre-processor and converted to __memset. Typically
that's because it's a memset generated by the compiler itself, and that
is the case here.
With GCC 12, allmodconfig enables CONFIG_INIT_STACK_ALL_PATTERN, which
causes the compiler to emit memset calls to initialise on-stack
variables with a pattern.
Because prom_init is non-user-facing boot-time only code, as a
workaround just disable stack variable initialisation to unbreak the
build.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220718134418.354114-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8386c414e2 ]
syzbot is reporting hung task at misc_open() [1], for there is a race
window of AB-BA deadlock which involves probe_count variable. Currently
wait_for_device_probe() from snapshot_open() from misc_open() can sleep
forever with misc_mtx held if probe_count cannot become 0.
When a device is probed by hub_event() work function, probe_count is
incremented before the probe function starts, and probe_count is
decremented after the probe function completed.
There are three cases that can prevent probe_count from dropping to 0.
(a) A device being probed stopped responding (i.e. broken/malicious
hardware).
(b) A process emulating a USB device using /dev/raw-gadget interface
stopped responding for some reason.
(c) New device probe requests keeps coming in before existing device
probe requests complete.
The phenomenon syzbot is reporting is (b). A process which is holding
system_transition_mutex and misc_mtx is waiting for probe_count to become
0 inside wait_for_device_probe(), but the probe function which is called
from hub_event() work function is waiting for the processes which are
blocked at mutex_lock(&misc_mtx) to respond via /dev/raw-gadget interface.
This patch mitigates (b) by deferring wait_for_device_probe() from
snapshot_open() to snapshot_write() and snapshot_ioctl(). Please note that
the possibility of (b) remains as long as any thread which is emulating a
USB device via /dev/raw-gadget interface can be blocked by uninterruptible
blocking operations (e.g. mutex_lock()).
Please also note that (a) and (c) are not addressed. Regarding (c), we
should change the code to wait for only one device which contains the
image for resuming from hibernation. I don't know how to address (a), for
use of timeout for wait_for_device_probe() might result in loss of user
data in the image. Maybe we should require the userland to wait for the
image device before opening /dev/snapshot interface.
Link: https://syzkaller.appspot.com/bug?extid=358c9ab4c93da7b7238c [1]
Reported-by: syzbot <syzbot+358c9ab4c93da7b7238c@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+358c9ab4c93da7b7238c@syzkaller.appspotmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75a185fb92 ]
In rcar_gen2_regulator_quirk(), for_each_matching_node_and_match() will
automatically increase and decrease the refcount. However, we should
call of_node_get() for the new reference created in 'quirk->np'.
Besides, we also should call of_node_put() before the 'quirk' being
freed.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220701121804.234223-1-windhl@126.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4f1f61ed5 ]
register_device_clock() misses a check for platform_device_register_simple().
Add a check to fix it.
Signed-off-by: huhai <huhai@kylinos.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b7ef7b05a ]
[821d6f0359] is to make machines
produced from 2012 to now not saving NVS region to accelerate S3.
But, Lenovo G40-45, a platform released in 2015, still needs NVS memory
saving during S3. A quirk is introduced for this platform.
Signed-off-by: Manyi Li <limanyi@uniontech.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7090e0ef3 ]
It seems that these quirks are no longer necessary since
commit 69b957c26b ("ACPI: EC: Fix possible issues related to EC
initialization order"), which has fixed this in a generic manner.
There are 3 commits adding DMI entries with this quirk (adding multiple
DMI entries per commit). 2/3 commits are from before the generic fix.
Which leaves commit 6306f04319 ("ACPI: EC: Make more Asus laptops
use ECDT _GPE"), which was committed way after the generic fix.
But this was just due to slow upstreaming of it. This commit stems
from Endless from 15 Aug 2017 (committed upstream 20 May 2021):
https://github.com/endlessm/linux/pull/288
The current code should work fine without this:
1. The EC_FLAGS_IGNORE_DSDT_GPE flag is only checked in ec_parse_device(),
like this:
if (boot_ec && boot_ec_is_ecdt && EC_FLAGS_IGNORE_DSDT_GPE) {
ec->gpe = boot_ec->gpe;
} else {
/* parse GPE */
}
2. ec_parse_device() is only called from acpi_ec_add() and
acpi_ec_dsdt_probe()
3. acpi_ec_dsdt_probe() starts with:
if (boot_ec)
return;
so it only calls ec_parse_device() when boot_ec == NULL, meaning that
the quirk never triggers for this call. So only the call in
acpi_ec_add() matters.
4. acpi_ec_add() does the following after the ec_parse_device() call:
if (boot_ec && ec->command_addr == boot_ec->command_addr &&
ec->data_addr == boot_ec->data_addr &&
!EC_FLAGS_TRUST_DSDT_GPE) {
/*
* Trust PNP0C09 namespace location rather than
* ECDT ID. But trust ECDT GPE rather than _GPE
* because of ASUS quirks, so do not change
* boot_ec->gpe to ec->gpe.
*/
boot_ec->handle = ec->handle;
acpi_handle_debug(ec->handle, "duplicated.\n");
acpi_ec_free(ec);
ec = boot_ec;
}
The quirk only matters if boot_ec != NULL and EC_FLAGS_TRUST_DSDT_GPE
is never set at the same time as EC_FLAGS_IGNORE_DSDT_GPE.
That means that if the addresses match we always enter this if block and
then only the ec->handle part of the data stored in ec by ec_parse_device()
is used and the rest is thrown away, after which ec is made to point
to boot_ec, at which point ec->gpe == boot_ec->gpe, so the same result
as with the quirk set, independent of the value of the quirk.
Also note the comment in this block which indicates that the gpe result
from ec_parse_device() is deliberately not taken to deal with buggy
Asus laptops and all DMI quirks setting EC_FLAGS_IGNORE_DSDT_GPE are for
Asus laptops.
Based on the above I believe that unless on some quirked laptops
the ECDT and DSDT EC addresses do not match we can drop the quirk.
I've checked dmesg output to ensure the ECDT and DSDT EC addresses match
for quirked models using https://linux-hardware.org hw-probe reports.
I've been able to confirm that the addresses match for the following
models this way: GL702VMK, X505BA, X505BP, X550VXK, X580VD.
Whereas for the following models I could find any dmesg output:
FX502VD, FX502VE, X542BA, X542BP.
Note the models without dmesg all were submitted in patches with a batch
of models and other models from the same batch checkout ok.
This, combined with that all the code adding the quirks was written before
the generic fix makes me believe that it is safe to remove this quirk now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Drake <drake@endlessos.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dd6db359e ]
Somehow the "ThinkPad X1 Carbon 6th" entry ended up twice in the
struct dmi_system_id acpi_ec_no_wakeup[] array. Remove one of
the entries.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
