[ Upstream commit 5ea0d42c1980e6d10e5cb56a78021db5bfcebaaf ]
Add RGMII to supported interfaces for BCM63xx RGMII ports so they can be
actually used in RGMII mode.
Without this, phylink will fail to configure them:
[ 3.580000] b53-switch 10700000.switch GbE3 (uninitialized): validation of rgmii with support 0000000,00000000,00000000,000062ff and advertisement 0000000,00000000,00000000,000062ff failed: -EINVAL
[ 3.600000] b53-switch 10700000.switch GbE3 (uninitialized): failed to connect to PHY: -EINVAL
[ 3.610000] b53-switch 10700000.switch GbE3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Fixes: ce3bf94871 ("net: dsa: b53: add support for BCM63xx RGMIIs")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250602193953.1010487-5-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50d9ce9679dd50df2dc51ada717fa875bc248fad ]
The logic added in the blamed commit was supposed to only omit nat source
port allocation if neither the existing nor the new entry are subject to
NAT.
However, its not enough to lookup the conntrack based on the proposed
tuple, we must also check the reverse direction.
Otherwise there are esoteric cases where the collision is in the reverse
direction because that colliding connection has a port rewrite, but the
new entry doesn't. In this case, we only check the new entry and then
erronously conclude that no clash exists anymore.
The existing (udp) tuple is:
a:p -> b:P, with nat translation to s:P, i.e. pure daddr rewrite,
reverse tuple in conntrack table is s:P -> a:p.
When another UDP packet is sent directly to s, i.e. a:p->s:P, this is
correctly detected as a colliding entry: tuple is taken by existing reply
tuple in reverse direction.
But the colliding conntrack is only searched for with unreversed
direction, and we can't find such entry matching a:p->s:P.
The incorrect conclusion is that the clashing entry has timed out and
that no port address translation is required.
Such conntrack will then be discarded at nf_confirm time because the
proposed reverse direction clashes with an existing mapping in the
conntrack table.
Search for the reverse tuple too, this will then check the NAT bits of
the colliding entry and triggers port reallocation.
Followp patch extends nft_nat.sh selftest to cover this scenario.
The IPS_SEQ_ADJUST change is also a bug fix:
Instead of checking for SEQ_ADJ this tested for SEEN_REPLY and ASSURED
by accident -- _BIT is only for use with the test_bit() API.
This bug has little consequence in practice, because the sequence number
adjustments are only useful for TCP which doesn't support clash resolution.
The existing test case (conntrack_reverse_clash.sh) exercise a race
condition path (parallel conntrack creation on different CPUs), so
the colliding entries have neither SEEN_REPLY nor ASSURED set.
Thanks to Yafang Shao and Shaun Brady for an initial investigation
of this bug.
Fixes: d8f84a9bc7c4 ("netfilter: nf_nat: don't try nat source port reallocation for reverse dir clash")
Closes: https://bugzilla.netfilter.org/show_bug.cgi?id=1795
Reported-by: Yafang Shao <laoar.shao@gmail.com>
Reported-by: Shaun Brady <brady.1345@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea77c397bff8b6d59f6d83dae1425b08f465e8b5 ]
If the first field doesn't cover the entire start map, then we must zero
out the remainder, else we leak those bits into the next match round map.
The early fix was incomplete and did only fix up the generic C
implementation.
A followup patch adds a test case to nft_concat_range.sh.
Fixes: 791a615b7ad2 ("netfilter: nf_set_pipapo: fix initial map fill")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12c331b29c7397ac3b03584e12902990693bc248 ]
gve_alloc_pending_packet() can return NULL, but gve_tx_add_skb_dqo()
did not check for this case before dereferencing the returned pointer.
Add a missing NULL check to prevent a potential NULL pointer
dereference when allocation fails.
This improves robustness in low-memory scenarios.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d46c4c839c20a599a0eb8d73708ce401f9c7d06d ]
Commit 03f1444016b7 ("PM: sleep: Fix handling devices with direct_complete
set on errors") caused power.is_suspended to be set for devices with
power.direct_complete set, but it forgot to ensure the clearing of that
flag for them in device_resume(), so power.is_suspended is still set for
them during the next system suspend-resume cycle.
If that cycle is aborted in dpm_suspend(), the subsequent invocation of
dpm_resume() will trigger a device_resume() call for every device and
because power.is_suspended is set for the devices in question, they will
not be skipped by device_resume() as expected which causes scary error
messages to be logged (as appropriate).
To address this issue, move the clearing of power.is_suspended in
device_resume() immediately after the power.is_suspended check so it
will be always cleared for all devices processed by that function.
Fixes: 03f1444016b7 ("PM: sleep: Fix handling devices with direct_complete set on errors")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4280
Reported-and-tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/4990586.GXAFRqVoOG@rjwysocki.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 982d30c30eaa2ec723df42e3bf526c014c1dbb88 ]
Commit 3d010c8031e3 ("udp: do not accept non-tunnel GSO skbs landing
in a tunnel") added checks in linux stack to not accept non-tunnel
GRO packets landing in a tunnel. This exposed an issue in vmxnet3
which was not correctly reporting GRO packets for tunnel packets.
This patch fixes this issue by setting correct GSO type for the
tunnel packets.
Currently, vmxnet3 does not support reporting inner fields for LRO
tunnel packets. The issue is not seen for egress drivers that do not
use skb inner fields. The workaround is to enable tnl-segmentation
offload on the egress interfaces if the driver supports it. This
problem pre-exists this patch fix and can be addressed as a separate
future patch.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com>
Acked-by: Guolin Yang <guolin.yang@broadcom.com>
Link: https://patch.msgid.link/20250530152701.70354-1-ronak.doshi@broadcom.com
[pabeni@redhat.com: dropped the changelog]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 905fe0845bb27e4eed2ca27ea06e6c4847f1b2b1 ]
When driver handles the napi rx polling requests, the netdev might
have been released by the dellink logic triggered by the disconnect
operation on user plane. However, in the logic of processing skb in
polling, an invalid netdev is still being used, which causes a panic.
BUG: kernel NULL pointer dereference, address: 00000000000000f1
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:dev_gro_receive+0x3a/0x620
[...]
Call Trace:
<IRQ>
? __die_body+0x68/0xb0
? page_fault_oops+0x379/0x3e0
? exc_page_fault+0x4f/0xa0
? asm_exc_page_fault+0x22/0x30
? __pfx_t7xx_ccmni_recv_skb+0x10/0x10 [mtk_t7xx (HASH:1400 7)]
? dev_gro_receive+0x3a/0x620
napi_gro_receive+0xad/0x170
t7xx_ccmni_recv_skb+0x48/0x70 [mtk_t7xx (HASH:1400 7)]
t7xx_dpmaif_napi_rx_poll+0x590/0x800 [mtk_t7xx (HASH:1400 7)]
net_rx_action+0x103/0x470
irq_exit_rcu+0x13a/0x310
sysvec_apic_timer_interrupt+0x56/0x90
</IRQ>
Fixes: 5545b7b9f2 ("net: wwan: t7xx: Add NAPI support")
Signed-off-by: Jinjian Song <jinjian.song@fibocom.com>
Link: https://patch.msgid.link/20250530031648.5592-1-jinjian.song@fibocom.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3382a1ed7f778db841063f5d7e317ac55f9e7f72 ]
Commit a1e40ac5b5e9 ("net: gso: fix udp gso fraglist segmentation after
pull from frag_list") detected invalid geometry in frag_list skbs and
redirects them from skb_segment_list to more robust skb_segment. But some
packets with modified geometry can also hit bugs in that code. We don't
know how many such cases exist. Addressing each one by one also requires
touching the complex skb_segment code, which risks introducing bugs for
other types of skbs. Instead, linearize all these packets that fail the
basic invariants on gso fraglist skbs. That is more robust.
If only part of the fraglist payload is pulled into head_skb, it will
always cause exception when splitting skbs by skb_segment. For detailed
call stack information, see below.
Valid SKB_GSO_FRAGLIST skbs
- consist of two or more segments
- the head_skb holds the protocol headers plus first gso_size
- one or more frag_list skbs hold exactly one segment
- all but the last must be gso_size
Optional datapath hooks such as NAT and BPF (bpf_skb_pull_data) can
modify fraglist skbs, breaking these invariants.
In extreme cases they pull one part of data into skb linear. For UDP,
this causes three payloads with lengths of (11,11,10) bytes were
pulled tail to become (12,10,10) bytes.
The skbs no longer meets the above SKB_GSO_FRAGLIST conditions because
payload was pulled into head_skb, it needs to be linearized before pass
to regular skb_segment.
skb_segment+0xcd0/0xd14
__udp_gso_segment+0x334/0x5f4
udp4_ufo_fragment+0x118/0x15c
inet_gso_segment+0x164/0x338
skb_mac_gso_segment+0xc4/0x13c
__skb_gso_segment+0xc4/0x124
validate_xmit_skb+0x9c/0x2c0
validate_xmit_skb_list+0x4c/0x80
sch_direct_xmit+0x70/0x404
__dev_queue_xmit+0x64c/0xe5c
neigh_resolve_output+0x178/0x1c4
ip_finish_output2+0x37c/0x47c
__ip_finish_output+0x194/0x240
ip_finish_output+0x20/0xf4
ip_output+0x100/0x1a0
NF_HOOK+0xc4/0x16c
ip_forward+0x314/0x32c
ip_rcv+0x90/0x118
__netif_receive_skb+0x74/0x124
process_backlog+0xe8/0x1a4
__napi_poll+0x5c/0x1f8
net_rx_action+0x154/0x314
handle_softirqs+0x154/0x4b8
[118.376811] [C201134] rxq0_pus: [name:bug&]kernel BUG at net/core/skbuff.c:4278!
[118.376829] [C201134] rxq0_pus: [name:traps&]Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
[118.470774] [C201134] rxq0_pus: [name:mrdump&]Kernel Offset: 0x178cc00000 from 0xffffffc008000000
[118.470810] [C201134] rxq0_pus: [name:mrdump&]PHYS_OFFSET: 0x40000000
[118.470827] [C201134] rxq0_pus: [name:mrdump&]pstate: 60400005 (nZCv daif +PAN -UAO)
[118.470848] [C201134] rxq0_pus: [name:mrdump&]pc : [0xffffffd79598aefc] skb_segment+0xcd0/0xd14
[118.470900] [C201134] rxq0_pus: [name:mrdump&]lr : [0xffffffd79598a5e8] skb_segment+0x3bc/0xd14
[118.470928] [C201134] rxq0_pus: [name:mrdump&]sp : ffffffc008013770
Fixes: a1e40ac5b5e9 ("gso: fix udp gso fraglist segmentation after pull from frag_list")
Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 030ce919e114a111e83b7976ecb3597cefd33f26 ]
The stmmac platform drivers that do not open-code the clk_ptp_rate value
after having retrieved the default one from the device-tree can end up
with 0 in clk_ptp_rate (as clk_get_rate can return 0). It will
eventually propagate up to PTP initialization when bringing up the
interface, leading to a divide by 0:
Division by zero in kernel.
CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.30-00001-g48313bd5768a #22
Hardware name: STM32 (Device Tree Support)
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x6c/0x8c
dump_stack_lvl from Ldiv0_64+0x8/0x18
Ldiv0_64 from stmmac_init_tstamp_counter+0x190/0x1a4
stmmac_init_tstamp_counter from stmmac_hw_setup+0xc1c/0x111c
stmmac_hw_setup from __stmmac_open+0x18c/0x434
__stmmac_open from stmmac_open+0x3c/0xbc
stmmac_open from __dev_open+0xf4/0x1ac
__dev_open from __dev_change_flags+0x1cc/0x224
__dev_change_flags from dev_change_flags+0x24/0x60
dev_change_flags from ip_auto_config+0x2e8/0x11a0
ip_auto_config from do_one_initcall+0x84/0x33c
do_one_initcall from kernel_init_freeable+0x1b8/0x214
kernel_init_freeable from kernel_init+0x24/0x140
kernel_init from ret_from_fork+0x14/0x28
Exception stack(0xe0815fb0 to 0xe0815ff8)
Prevent this division by 0 by adding an explicit check and error log
about the actual issue. While at it, remove the same check from
stmmac_ptp_register, which then becomes duplicate
Fixes: 19d857c903 ("stmmac: Fix calculations for ptp counters when clock input = 50Mhz.")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-1-d73340a794d5@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73145e6d81070d34a21431c9e0d7aaf2f29ca048 ]
The current implementation of the Tx scheduler allows the tree to be
rebuilt as the user adds more Tx queues to the VSI. In such a case,
additional child nodes are added to the tree to support the new number
of queues.
Unfortunately, this algorithm does not take into account that the limit
of the VSI support node may be exceeded, so an additional node in the
VSI layer may be required to handle all the requested queues.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs. Although the driver still respects the queue limit returned by
the FW, the Tx scheduler was unable to add those queues to its tree
and returned one of the errors below.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs (e.g. at least 321 CPUs, if there is already 128 Tx/Rx queue pairs).
Although the driver still respects the queue limit returned by the FW,
the Tx scheduler was unable to add those queues to its tree and returned
the following errors:
Failed VSI LAN queue config for XDP, error: -5
or:
Failed to set LAN Tx queue context, error: -22
Fix this problem by extending the tree rebuild algorithm to check if the
current VSI node can support the requested number of queues. If it
cannot, create as many additional VSI support nodes as necessary to
handle all the required Tx queues. Symmetrically, adjust the VSI node
removal algorithm to remove all nodes associated with the given VSI.
Also, make the search for the next free VSI node more restrictive. That is,
add queue group nodes only to the VSI support nodes that have a matching
VSI handle.
Finally, fix the comment describing the tree update algorithm to better
reflect the current scenario.
Fixes: b0153fdd7e ("ice: update VSI config dynamically")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fa2942578472c9cab13a8fc1dae0d830193e0a1 ]
The current implementation of the Tx scheduler tree attempts
to create nodes for all Tx queues, ignoring the fact that some
queues may already exist in the tree. For example, if the VSI
already has 128 Tx queues and the user requests for 16 new queues,
the Tx scheduler will compute the tree for 272 queues (128 existing
queues + 144 new queues), instead of 144 queues (128 existing queues
and 16 new queues).
Fix that by modifying the node count calculation algorithm to skip
the queues that already exist in the tree.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0153f36041b8e52019ebfa8629c13bf8f9b0a951 ]
When the XDP program is loaded, the XDP callback adds new Tx queues.
This means that the callback must update the Tx scheduler with the new
queue number. In the event of a Tx scheduler failure, the XDP callback
should also fail and roll back any changes previously made for XDP
preparation.
The previous implementation had a bug that not all changes made by the
XDP callback were rolled back. This caused the crash with the following
call trace:
[ +9.549584] ice 0000:ca:00.0: Failed VSI LAN queue config for XDP, error: -5
[ +0.382335] Oops: general protection fault, probably for non-canonical address 0x50a2250a90495525: 0000 [#1] SMP NOPTI
[ +0.010710] CPU: 103 UID: 0 PID: 0 Comm: swapper/103 Not tainted 6.14.0-net-next-mar-31+ #14 PREEMPT(voluntary)
[ +0.010175] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022
[ +0.010946] RIP: 0010:__ice_update_sample+0x39/0xe0 [ice]
[...]
[ +0.002715] Call Trace:
[ +0.002452] <IRQ>
[ +0.002021] ? __die_body.cold+0x19/0x29
[ +0.003922] ? die_addr+0x3c/0x60
[ +0.003319] ? exc_general_protection+0x17c/0x400
[ +0.004707] ? asm_exc_general_protection+0x26/0x30
[ +0.004879] ? __ice_update_sample+0x39/0xe0 [ice]
[ +0.004835] ice_napi_poll+0x665/0x680 [ice]
[ +0.004320] __napi_poll+0x28/0x190
[ +0.003500] net_rx_action+0x198/0x360
[ +0.003752] ? update_rq_clock+0x39/0x220
[ +0.004013] handle_softirqs+0xf1/0x340
[ +0.003840] ? sched_clock_cpu+0xf/0x1f0
[ +0.003925] __irq_exit_rcu+0xc2/0xe0
[ +0.003665] common_interrupt+0x85/0xa0
[ +0.003839] </IRQ>
[ +0.002098] <TASK>
[ +0.002106] asm_common_interrupt+0x26/0x40
[ +0.004184] RIP: 0010:cpuidle_enter_state+0xd3/0x690
Fix this by performing the missing unmapping of XDP queues from
q_vectors and setting the XDP rings pointer back to NULL after all those
queues are released.
Also, add an immediate exit from the XDP callback in case of ring
preparation failure.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03dba9cea72f977e873e4e60e220fa596959dd8f ]
Depending on the security set the response to L2CAP_LE_CONN_REQ shall be
just L2CAP_CR_LE_ENCRYPTION if only encryption when BT_SECURITY_MEDIUM
is selected since that means security mode 2 which doesn't require
authentication which is something that is covered in the qualification
test L2CAP/LE/CFC/BV-25-C.
Link: https://github.com/bluez/bluez/issues/1270
Fixes: 27e2d4c8d2 ("Bluetooth: Add basic LE L2CAP connect request receiving support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27eab4c644236a9324084a70fe79e511cbd07393 ]
When running these commands on DUT (and similar at the other end)
ip link set dev eth0 up
ip link add link eth0 name eth0.10 type vlan id 10
ip addr add 10.0.0.1/24 dev eth0.10
ip link set dev eth0.10 up
ping 10.0.0.2
The ping will fail.
The reason why is failing is because, the network interfaces for lan966x
have a flag saying that the HW can insert the vlan tags into the
frames(NETIF_F_HW_VLAN_CTAG_TX). Meaning that the frames that are
transmitted don't have the vlan tag inside the skb data, but they have
it inside the skb. We already get that vlan tag and put it in the IFH
but the problem is that we don't configure the HW to rewrite the frame
when the interface is in host mode.
The fix consists in actually configuring the HW to insert the vlan tag
if it is different than 0.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Fixes: 6d2c186afa ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250528093619.3738998-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54d34165b4f786d7fea8412a18fb4a54c1eab623 ]
The "freq" variable is in terms of MHz and "max_val_cycles" is in terms
of Hz. The fact that "max_val_cycles" is a u64 suggests that support
for high frequency is intended but the "freq_khz * 1000" would overflow
the u32 type if we went above 4GHz. Use unsigned long long type for the
mutliplication to prevent that.
Fixes: 31c128b66e ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/aDbFHe19juIJKjsb@stanley.mountain
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba99c627aac85bc746fb4a6e2d79edb3ad100326 ]
Identify the cause of the suspend/resume hang: netif_carrier_off()
is called during link state changes and becomes stuck while
executing linkwatch_work().
To resolve this issue, call netif_device_detach() during the Ethernet
suspend process to temporarily detach the network device from the
kernel and prevent the suspend/resume hang.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Yanqing Wang <ot_yanqing.wang@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Link: https://patch.msgid.link/20250528075351.593068-1-macpaul.lin@mediatek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f41a94aade120dc60322865f363cee7865f2df01 ]
Previously, the RX_BUFFERS_POSTED stat incorrectly reported the
fill_cnt from RX queue 0 for all queues, resulting in inaccurate
per-queue statistics.
Fix this by correctly indexing priv->rx[idx].fill_cnt for each RX queue.
Fixes: 24aeb56f2d ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20250527130830.1812903-1-alok.a.tiwari@oracle.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb7fd7aa35bfcc1e1fda4ecc42ccfcb526cdc780 ]
bus_id is currently derived from the ethernetX alias. If one is missing
for the device, 0 is used. If ethernet0 points to another stmmac device
or if there are 2+ stmmac devices without an ethernet alias, then bus_id
will be 0 for all of those.
This is an issue because the bus_id is used to generate the mdio bus id
(new_bus->id in drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
stmmac_mdio_register) and this needs to be unique.
This allows to avoid needing to define ethernet aliases for devices with
multiple stmmac controllers (such as the Rockchip RK3588) for multiple
stmmac devices to probe properly.
Obviously, the bus_id isn't guaranteed to be stable across reboots if no
alias is set for the device but that is easily fixed by simply adding an
alias if this is desired.
Fixes: 25c83b5c2e ("dt:net:stmmac: Add support to dwmac version 3.610 and 3.710")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250527-stmmac-mdio-bus_id-v2-1-a5ca78454e3c@cherry.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 408c97c4a5e0b634dcd15bf8b8808b382e888164 ]
While enable active config via cscfg_csdev_enable_active_config(),
active config could be deactivated via configfs' sysfs interface.
This could make UAF issue in below scenario:
CPU0 CPU1
(sysfs enable) load module
cscfg_load_config_sets()
activate config. // sysfs
(sys_active_cnt == 1)
...
cscfg_csdev_enable_active_config()
lock(csdev->cscfg_csdev_lock)
// here load config activate by CPU1
unlock(csdev->cscfg_csdev_lock)
deactivate config // sysfs
(sys_activec_cnt == 0)
cscfg_unload_config_sets()
unload module
// access to config_desc which freed
// while unloading module.
cscfg_csdev_enable_config
To address this, use cscfg_config_desc's active_cnt as a reference count
which will be holded when
- activate the config.
- enable the activated config.
and put the module reference when config_active_cnt == 0.
Fixes: f8cce2ff3c ("coresight: syscfg: Add API to activate and enable configurations")
Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250514161951.3427590-4-yeoreum.yun@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ebf1982038af12f3588417e4fd0417d2551da28 ]
fpga_mgr_test_img_load_sgt() allocates memory for sgt using
kunit_kzalloc() however it does not check if the allocation failed.
It then passes sgt to sg_alloc_table(), which passes it to
__sg_alloc_table(). This function calls memset() on sgt in an attempt to
zero it out. If the allocation fails then sgt will be NULL and the
memset will trigger a NULL pointer dereference.
Fix this by checking the allocation with KUNIT_ASSERT_NOT_ERR_OR_NULL().
Reviewed-by: Marco Pagani <marco.pagani@linux.dev>
Fixes: ccbc1c3021 ("fpga: add an initial KUnit suite for the FPGA Manager")
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20250422153737.5264-1-qasdev00@gmail.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7351312632e831e51383f48957d47712fae791ef ]
Enable/disable seems to be racy on SMP, consider the following scenario:
CPU0 CPU1
interrupt_cnt_enable_write(true)
{
if (priv->enabled == enable)
return 0;
if (enable) {
priv->enabled = true;
interrupt_cnt_enable_write(false)
{
if (priv->enabled == enable)
return 0;
if (enable) {
priv->enabled = true;
enable_irq(priv->irq);
} else {
disable_irq(priv->irq)
priv->enabled = false;
}
enable_irq(priv->irq);
} else {
disable_irq(priv->irq);
priv->enabled = false;
}
The above would result in priv->enabled == false, but IRQ left enabled.
Protect both write (above race) and read (to propagate the value on SMP)
callbacks with a mutex.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Fixes: a55ebd47f2 ("counter: add IRQ or GPIO based counter")
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250331163642.2382651-1-alexander.sverdlin@siemens.com
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9016776f1301627de78a633bda7c898425a56572 ]
This patch allows writing u64 values to the ADMV8818's high and low-pass
filter frequencies. It includes the following changes:
- Rejects negative frequencies in admv8818_write_raw.
- Adds a write_raw_get_fmt function to admv8818's iio_info, returning
IIO_VAL_INT_64 for the high and low-pass filter 3dB frequency channels.
Fixes: f34fe888ad ("iio:filter:admv8818: add support for ADMV8818")
Signed-off-by: Brian Pellegrino <bpellegrino@arka.org>
Signed-off-by: Sam Winchenbach <swinchenbach@arka.org>
Link: https://patch.msgid.link/20250328174831.227202-7-sam.winchenbach@framepointer.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a760d10ded372d113a0410c42be246315bbc2ff ]
commit a5cfc9d658 ("thunderbolt: Add wake on connect/disconnect
on USB4 ports") introduced a sysfs file to control wake up policy
for a given USB4 port that defaulted to disabled.
However when testing commit 4bfeea6ec1c02 ("thunderbolt: Use wake
on connect and disconnect over suspend") I found that it was working
even without making changes to the power/wakeup file (which defaults
to disabled). This is because of a logic error doing a bitwise or
of the wake-on-connect flag with device_may_wakeup() which should
have been a logical AND.
Adjust the logic so that policy is only applied when wakeup is
actually enabled.
Fixes: a5cfc9d658 ("thunderbolt: Add wake on connect/disconnect on USB4 ports")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5af9f1fa576874b24627d4c05e3a84672204c200 ]
When an application sets and enables an alarm on Loongson RTC devices,
the alarm notification fails to propagate to userspace because the
ACPI event handler omits calling rtc_update_irq().
As a result, processes waiting via select() or poll() on RTC device
files fail to receive alarm notifications.
The ACPI interrupt is also triggered multiple times. In loongson_rtc_handler,
we need to clear TOY_MATCH0_REG to resolve this issue.
Fixes: 09471d8f5b39 ("rtc: loongson: clear TOY_MATCH0_REG in loongson_rtc_isr()")
Fixes: 1b733a9ebc ("rtc: Add rtc driver for the Loongson family chips")
Signed-off-by: Liu Dalin <liudalin@kylinsec.com.cn>
Reviewed-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/20250509084416.7979-1-liudalin@kylinsec.com.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d14402a38c2d868cacb1facaf9be908ca6558e59 ]
The qmp_usb_iomap() helper function currently returns the raw result of
devm_ioremap() for non-exclusive mappings. Since devm_ioremap() may return
a NULL pointer and the caller only checks error pointers with IS_ERR(),
NULL could bypass the check and lead to an invalid dereference.
Fix the issue by checking if devm_ioremap() returns NULL. When it does,
qmp_usb_iomap() now returns an error pointer via IOMEM_ERR_PTR(-ENOMEM),
ensuring safe and consistent error handling.
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Fixes: a5d6b1ac56 ("phy: qcom-qmp-usb: fix memleak on probe deferral")
CC: Johan Hovold <johan@kernel.org>
CC: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414125050.2118619-1-chenyuan0y@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8805f32a96d3b97cef07999fa6f52112678f7e65 ]
If the call to pci_host_probe() in cdns_pcie_host_setup() fails, PM
runtime count is decremented in the error path using pm_runtime_put_sync().
But the runtime count is not incremented by this driver, but only by the
callers (cdns_plat_pcie_probe/j721e_pcie_probe). And the callers also
decrement the runtime PM count in their error path. So this leads to the
below warning from the PM core:
"runtime PM usage count underflow!"
So fix it by getting rid of pm_runtime_put_sync() in the error path and
directly return the errno.
Fixes: 49e427e6bd ("Merge branch 'pci/host-probe-refactor'")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250419133058.162048-1-18255117159@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f2efdbc303fe7baa83843d3290dd6ea5ba3276c ]
The DT bindings for this driver define the interrupts in the order as
they are numbered in the interrupt controller. The old platform_data,
however, listed them in a different order. So, for DT based platforms,
they are mixed up. Assign them specifically for DT, so we can keep the
bindings stable. After the fix, 'rtctest' passes again on the Renesas
Genmai board (RZ-A1 / R7S72100).
Fixes: dab5aec64b ("rtc: sh: add support for rza series")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250227134256.9167-11-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56e84c64fc257a95728ee73165456b025c48d408 ]
Validate the SMB1 query reparse point response per [MS-CIFS] section
2.2.7.2 NT_TRANSACT_IOCTL.
NT_TRANSACT_IOCTL response contains one word long setup data after which is
ByteCount member. So check that SetupCount is 1 before trying to read and
use ByteCount member.
Output setup data contains ReturnedDataLen member which is the output
length of executed IOCTL command by remote system. So check that output was
not truncated before transferring over network.
Change MaxSetupCount of NT_TRANSACT_IOCTL request from 4 to 1 as io_rsp
structure already expects one word long output setup data. This should
prevent server sending incompatible structure (in case it would be extended
in future, which is unlikely).
Change MaxParameterCount of NT_TRANSACT_IOCTL request from 2 to 0 as
NT IOCTL does not have any documented output parameters and this function
does not parse any output parameters at all.
Fixes: ed3e0a149b58 ("smb: client: implement ->query_reparse_point() for SMB1")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80c4de6ab44c14e910117a02f2f8241ffc6ec54a ]
In some scenarios, when mounting NFS, more than one superblock may be
created. The final superblock used is the last one created, but only the
first superblock carries the ro flag passed from user space. If a ro flag
is added to the superblock via remount, it will trigger the issue
described in Link[1].
Link[2] attempted to address this by marking the superblock as ro during
the initial mount. However, this introduced a new problem in scenarios
where multiple mount points share the same superblock:
[root@a ~]# mount /dev/sdb /mnt/sdb
[root@a ~]# echo "/mnt/sdb *(rw,no_root_squash)" > /etc/exports
[root@a ~]# echo "/mnt/sdb/test_dir2 *(ro,no_root_squash)" >> /etc/exports
[root@a ~]# systemctl restart nfs-server
[root@a ~]# mount -t nfs -o rw 127.0.0.1:/mnt/sdb/test_dir1 /mnt/test_mp1
[root@a ~]# mount | grep nfs4
127.0.0.1:/mnt/sdb/test_dir1 on /mnt/test_mp1 type nfs4 (rw,relatime,...
[root@a ~]# mount -t nfs -o ro 127.0.0.1:/mnt/sdb/test_dir2 /mnt/test_mp2
[root@a ~]# mount | grep nfs4
127.0.0.1:/mnt/sdb/test_dir1 on /mnt/test_mp1 type nfs4 (ro,relatime,...
127.0.0.1:/mnt/sdb/test_dir2 on /mnt/test_mp2 type nfs4 (ro,relatime,...
[root@a ~]#
When mounting the second NFS, the shared superblock is marked as ro,
causing the previous NFS mount to become read-only.
To resolve both issues, the ro flag is no longer applied to the superblock
during remount. Instead, the ro flag on the mount is used to control
whether the mount point is read-only.
Fixes: 281cad46b3 ("NFS: Create a submount rpc_op")
Link[1]: https://lore.kernel.org/all/20240604112636.236517-3-lilingfeng@huaweicloud.com/
Link[2]: https://lore.kernel.org/all/20241130035818.1459775-1-lilingfeng3@huawei.com/
Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cd9b785943c57a136536250da80ba1eb6f8eb18 ]
As described in the link, commit 52cb7f8f1778 ("nfs: ignore SB_RDONLY when
mounting nfs") removed the check for the ro flag when determining whether
to share the superblock, which caused issues when mounting different
subdirectories under the same export directory via NFSv3. However, this
change did not affect NFSv4.
For NFSv3:
1) A single superblock is created for the initial mount.
2) When mounted read-only, this superblock carries the SB_RDONLY flag.
3) Before commit 52cb7f8f1778 ("nfs: ignore SB_RDONLY when mounting nfs"):
Subsequent rw mounts would not share the existing ro superblock due to
flag mismatch, creating a new superblock without SB_RDONLY.
After the commit:
The SB_RDONLY flag is ignored during superblock comparison, and this leads
to sharing the existing superblock even for rw mounts.
Ultimately results in write operations being rejected at the VFS layer.
For NFSv4:
1) Multiple superblocks are created and the last one will be kept.
2) The actually used superblock for ro mounts doesn't carry SB_RDONLY flag.
Therefore, commit 52cb7f8f1778 doesn't affect NFSv4 mounts.
Clear SB_RDONLY before getting superblock when NFS_MOUNT_UNSHARED is not
set to fix it.
Fixes: 52cb7f8f1778 ("nfs: ignore SB_RDONLY when mounting nfs")
Closes: https://lore.kernel.org/all/12d7ea53-1202-4e21-a7ef-431c94758ce5@app.fastmail.com/T/
Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7a48ea9b919e2fa0e4a1d9938fdb03e9afe276c ]
The syscalls that were consistently observed were set_robust_list and
rseq. This is because perf cannot find their child process.
This change ensures that the return value is always printed.
Before:
0.256 ( 0.001 ms): set_robust_list(head: 0x7f09c77dba20, len: 24) =
0.259 ( 0.001 ms): rseq(rseq: 0x7f09c77dc0e0, rseq_len: 32, sig: 1392848979) =
After:
0.270 ( 0.002 ms): set_robust_list(head: 0x7f0bb14a6a20, len: 24) = 0
0.273 ( 0.002 ms): rseq(rseq: 0x7f0bb14a70e0, rseq_len: 32, sig: 1392848979) = 0
Committer notes:
As discussed in the thread in the Link: tag below, these two don't
return a pid, but for syscalls returning one, we need to print the
result and if we manage to find the children in 'perf trace' data
structures, then print its name as well.
Fixes: 11c8e39f51 ("perf trace: Infrastructure to show COMM strings for syscalls returning PIDs")
Reviewed-by: Howard Chu <howardchu95@gmail.com>
Signed-off-by: Anubhav Shelat <ashelat@redhat.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Dapeng Mi <dapeng1.mi@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20250403160411.159238-2-ashelat@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 628e124404b3db5e10e17228e680a2999018ab33 ]
The test might fail on the Arm64 platform with the error:
# perf test -vvv "Track with sched_switch"
Missing sched_switch events
#
The issue is caused by incorrect handling of timestamp comparisons. The
comparison result, a signed 64-bit value, was being directly cast to an
int, leading to incorrect sorting for sched events.
The case does not fail everytime, usually I can trigger the failure
after run 20 ~ 30 times:
# while true; do perf test "Track with sched_switch"; done
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : FAILED!
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
106: Track with sched_switch : FAILED!
106: Track with sched_switch : Ok
106: Track with sched_switch : Ok
I used cross compiler to build Perf tool on my host machine and tested on
Debian / Juno board. Generally, I think this issue is not very specific
to GCC versions. As both internal CI and my local env can reproduce the
issue.
My Host Build compiler:
# aarch64-linux-gnu-gcc --version
aarch64-linux-gnu-gcc (Ubuntu 13.3.0-6ubuntu2~24.04) 13.3.0
Juno Board:
# lsb_release -a
No LSB modules are available.
Distributor ID: Debian
Description: Debian GNU/Linux 12 (bookworm)
Release: 12
Codename: bookworm
Fix this by explicitly returning 0, 1, or -1 based on whether the result
is zero, positive, or negative.
Fixes: d44bc55829 ("perf tests: Add a test for tracking with sched_switch")
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20250331172759.115604-1-leo.yan@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
