commit 86b53fbf08 upstream.
A return value of 0 means success. This is documented in lib/kstrtox.c.
This was found by trying to mount an NFS share from a link-local IPv6
address with the interface specified by its index:
mount("[fe80::1%1]:/srv/nfs", "/mnt", "nfs", 0, "nolock,addr=fe80::1%1")
Before this commit this failed with EINVAL and also caused the following
message in dmesg:
[...] NFS: bad IP address specified: addr=fe80::1%1
The syscall using the same address based on the interface name instead
of its index succeeds.
Credits for this patch go to my colleague Christian Speich, who traced
the origin of this bug to this line of code.
Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de>
Fixes: 00cfaa943e ("replace strict_strto calls")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d6ffc63f1 upstream.
The VT-d hardware will ignore those Addr bits which have been masked by
the AM field in the PASID-based-IOTLB invalidation descriptor. As the
result, if the starting address in the descriptor is not aligned with
the address mask, some IOTLB caches might not invalidate. Hence people
will see below errors.
[ 1093.704661] dmar_fault: 29 callbacks suppressed
[ 1093.704664] DMAR: DRHD: handling fault status reg 3
[ 1093.712738] DMAR: [DMA Read] Request device [7a:02.0] PASID 2
fault addr 7f81c968d000 [fault reason 113]
SM: Present bit in first-level paging entry is clear
Fix this by using aligned address for PASID-based-IOTLB invalidation.
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Reported-and-tested-by: Guo Kaijie <Kaijie.Guo@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201231005323.2178523-2-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ff60eb052 upstream.
acquire_slab() fails if there is contention on the freelist of the page
(probably because some other CPU is concurrently freeing an object from
the page). In that case, it might make sense to look for a different page
(since there might be more remote frees to the page from other CPUs, and
we don't want contention on struct page).
However, the current code accidentally stops looking at the partial list
completely in that case. Especially on kernels without CONFIG_NUMA set,
this means that get_partial() fails and new_slab_objects() falls back to
new_slab(), allocating new pages. This could lead to an unnecessary
increase in memory fragmentation.
Link: https://lkml.kernel.org/r/20201228130853.1871516-1-jannh@google.com
Fixes: 7ced371971 ("slub: Acquire_slab() avoid loop")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00cb645fd7 upstream.
Commit 25b4620ee8 ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
added an intel_dsi_msleep() helper which skips sleeping if the
MIPI-sequences have a version of 3 or newer and the panel is in vid-mode;
and it moved a bunch of msleep-s over to this new helper.
This was based on my reading of the big comment around line 730 which
starts with "Panel enable/disable sequences from the VBT spec.",
where the "v3 video mode seq" column does not have any wait t# entries.
Given that this code has been used on a lot of different devices without
issues until now, it seems that my interpretation of the spec here is
mostly correct.
But now I have encountered one device, an Acer Aspire Switch 10 E
SW3-016, where the panel will not light up unless we do actually honor the
panel_on_delay after exexuting the MIPI_SEQ_PANEL_ON sequence.
What seems to set this model apart is that it is lacking a
MIPI_SEQ_DEASSERT_RESET sequence, which is where the power-on
delay usually happens.
Fix the panel not lighting up on this model by using an unconditional
msleep(panel_on_delay) instead of intel_dsi_msleep() when there is
no MIPI_SEQ_DEASSERT_RESET sequence.
Fixes: 25b4620ee8 ("drm/i915/dsi: Skip delays for v3 VBTs in vid-mode")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201118124058.26021-1-hdegoede@redhat.com
(cherry picked from commit 6fdb335f1c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 869c4d5eb1 upstream.
The function bnxt_get_ulp_stat_ctxs() does not count the stats contexts
used by the RDMA driver correctly when the RDMA driver is freeing the
MSIX vectors. It assumes that if the RDMA driver is registered, the
additional stats contexts will be needed. This is not true when the
RDMA driver is about to unregister and frees the MSIX vectors.
This slight error leads to over accouting of the stats contexts needed
after the RDMA driver has unloaded. This will cause some firmware
warning and error messages in dmesg during subsequent config. changes
or ifdown/ifup.
Fix it by properly accouting for extra stats contexts only if the
RDMA driver is registered and MSIX vectors have been successfully
requested.
Fixes: c027c6b4e9 ("bnxt_en: get rid of num_stat_ctxs variable")
Reviewed-by: Yongping Zhang <yongping.zhang@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c638cdb8e upstream.
xa_alloc_cyclic() call returns positive number if ID allocation
succeeded but wrapped. It is not an error, so normalize the "ret"
variable to zero as marker of not-an-error.
drivers/infiniband/core/restrack.c:261 rdma_restrack_add()
warn: 'ret' can be either negative or positive
Fixes: fd47c2f99f ("RDMA/restrack: Convert internal DB from hash to XArray")
Link: https://lore.kernel.org/r/20201216100753.1127638-1-leon@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 896567ee7f upstream.
Before referencing the inode, we must ensure that the superblock can be
referenced. Otherwise, we can end up with iput() calling superblock
operations that are no longer valid or accessible.
Fixes: ea7c38fef0 ("NFSv4: Ensure we reference the inode for return-on-close in delegreturn")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb2856c597 upstream.
If we exit _lgopen_prepare_attached() without setting a layout, we will
currently leak the plh_outstanding counter.
Fixes: 411ae722d1 ("pNFS: Wait for stale layoutget calls to complete in pnfs_update_layout()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c8d5fc37f upstream.
If a layout return is in progress, we should wait for it to complete,
in case the layout segment we are picking up gets returned too.
Fixes: 30cb3ee299 ("pNFS: Handle NFS4ERR_OLD_STATEID on layoutreturn by bumping the state seqid")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67bbceedc9 upstream.
If the layout return-on-close failed because the layoutreturn was never
sent, then we should mark the layout for return again.
Fixes: 9c47b18cf7 ("pNFS: Ensure we do clear the return-on-close layout stateid on fatal errors")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 078000d02d upstream.
If the inode is being evicted, it should be safe to run return-on-close,
so we should do it to ensure we don't inadvertently leak layout segments.
Fixes: 1c5bd76d17 ("pNFS: Enable layoutreturn operation for return-on-close")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1a90ab0e upstream.
It is only safe to call the tracepoint before rpc_put_task() because
'data' is freed inside nfs4_lock_release (rpc_release).
Fixes: 48c9579a1a ("Adding stateid information to tracepoints")
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca1ff67d0f upstream.
When a bio merges, we can get a request that spans multiple
bios, and the overall request payload size is the sum of
all bios. When we calculate how much we need to send
from the existing bio (and bvec), we did not take into
account the iov_iter byte count cap.
Since multipage bvecs support, bvecs can split in the middle
which means that when we account for the last bvec send we
should also take the iov_iter byte count cap as it might be
lower than the last bvec size.
Reported-by: Hao Wang <pkuwangh@gmail.com>
Fixes: 3f2304f8c6 ("nvme-tcp: add NVMe over TCP host driver")
Tested-by: Hao Wang <pkuwangh@gmail.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 671ee4db95 upstream.
When the axg-tdm-interface was introduced, the backend DAI was marked as an
endpoint when DPCM was walking the DAPM graph to find a its BE.
It is no longer the case since this
commit 8dd26dff00 ("ASoC: dapm: Fix handling of custom_stop_condition on DAPM graph walks")
Because of this, when DPCM finds a BE it does everything it needs on the
DAIs but it won't power up the widgets between the FE and the BE if there
is no actual endpoint after the BE.
On meson-axg HWs, the loopback is a special DAI of the tdm-interface BE.
It is only linked to the dummy codec since there no actual HW after it.
>From the DAPM perspective, the DAI has no endpoint. Because of this, the TDM
decoder, which is a widget between the FE and BE is not powered up.
>From the user perspective, everything seems fine but no data is produced.
Connecting the Loopback DAI to a dummy DAPM endpoint solves the problem.
Fixes: 8dd26dff00 ("ASoC: dapm: Fix handling of custom_stop_condition on DAPM graph walks")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201217150812.3247405-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d36a1dd9f7 upstream.
We are not guaranteed the locking environment that would prevent
dentry getting renamed right under us. And it's possible for
old long name to be freed after rename, leading to UAF here.
Cc: stable@kernel.org # v2.6.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5501e9229a upstream.
In some cases, the number of cpus (nr_cpus_online) is confused with the
maximum cpu number (nr_cpus_avail), which results in the error in the
example below:
Example on system with 8 cpus:
Before:
# echo 0 > /sys/devices/system/cpu/cpu2/online
# ./perf record --kcore -e intel_pt// taskset --cpu-list 7 uname
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.147 MB perf.data ]
# ./perf script --itrace=e
Requested CPU 7 too large. Consider raising MAX_NR_CPUS
0x25908 [0x8]: failed to process type: 68 [Invalid argument]
After:
# ./perf script --itrace=e
#
Fixes: 8c7274691f ("perf machine: Replace MAX_NR_CPUS with perf_env::nr_cpus_online")
Fixes: 7df4e36a47 ("perf session: Replace MAX_NR_CPUS with perf_env::nr_cpus_online")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210107174159.24897-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee61cfd955 ]
It adds a stub acpi_create_platform_device() for !CONFIG_ACPI build, so
that caller doesn't have to deal with !CONFIG_ACPI build issue.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ceb786353 ]
When a queue is in NVMET_RDMA_Q_CONNECTING state, it may has some
requests at rsp_wait_list. In case a disconnect occurs at this
state, no one will empty this list and will return the requests to
free_rsps list. Normally nvmet_rdma_queue_established() free those
requests after moving the queue to NVMET_RDMA_Q_LIVE state, but in
this case __nvmet_rdma_queue_disconnect() is called before. The
crash happens at nvmet_rdma_free_rsps() when calling
list_del(&rsp->free_list), because the request exists only at
the wait list. To fix the issue, simply clear rsp_wait_list when
destroying the queue.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ee5c78ca3 ]
A system with more than one of these SSDs will only have one usable.
Hence the kernel fails to detect nvme devices due to duplicate cntlids.
[ 6.274554] nvme nvme1: Duplicate cntlid 33 with nvme0, rejecting
[ 6.274566] nvme nvme1: Removing after probe failure status: -22
Adding the NVME_QUIRK_IGNORE_DEV_SUBNQN quirk to resolves the issue.
Signed-off-by: Gopal Tiwari <gtiwari@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3503ee6c0b ]
The udpgro.sh will always return 0 (unless the bpf selftest was not
build first) even if there are some failed sub test-cases.
Therefore the kselftest framework will report this case is OK.
Check and return the exit status of each test to make it easier to
spot real failures.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 445c6198fe ]
Since commit 1d6cd39293 ("modpost: turn missing MODULE_LICENSE()
into error") the ppc32_allmodconfig build fails with:
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-fec.o
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-bitbang.o
Add the missing MODULE_LICENSEs to fix the build. Both files include a
copyright header indicating they are GPL v2.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51049bd903 ]
Without this, we run into a link error
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o: in function `dsp_audio_generate_law_tables':
(.text+0x30c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o:(.text+0x5e4): more undefined references to `byte_rev_table' follow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d4d273588 ]
BFQ computes number of tags it allows to be allocated for each request type
based on tag bitmap. However it uses 1 << bitmap.shift as number of
available tags which is wrong. 'shift' is just an internal bitmap value
containing logarithm of how many bits bitmap uses in each bitmap word.
Thus number of tags allowed for some request types can be far to low.
Use proper bitmap.depth which has the number of tags instead.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c36d88cff ]
Older versions of BSD awk are fussy about the order of '-v' and '-f'
flags, and require a space after the flag name. This causes build
failures on platforms with an old awk, such as macOS and NetBSD.
Since GNU awk and modern versions of BSD awk (distributed with
FreeBSD/OpenBSD) are fine with either form, the definition of
'cmd_unroll' can be trivially tweaked to let the lib/raid6 Makefile
work with both old and new awk flag dialects.
Signed-off-by: John Millikin <john@john-millikin.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eda52334e ]
With MAX_PWM being defined to 255 the code
unsigned long period;
...
period = ctx->pwm->args.period;
state.duty_cycle = DIV_ROUND_UP(pwm * (period - 1), MAX_PWM);
calculates a too small value for duty_cycle if the configured period is
big (either by discarding the 64 bit value ctx->pwm->args.period or by
overflowing the multiplication). As this results in a too slow fan and
so maybe an overheating machine better be safe than sorry and error out
in .probe.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201215092031.152243-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b000700d6d ]
When kzalloc() fails, we should execute hl_mmu_fini()
to release the MMU module. It's the same when
hl_ctx_init() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcaebc7354 ]
We need to make sure our device is idle when rebooting a virtual
machine. This is done in the driver level.
The firmware will later handle FLR but we want to be extra safe and
stop the devices until the FLR is handled.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 887078de2a ]
Table 8-53 in the QUICC Engine Reference manual shows definitions of
fields up to a size of 192 bytes, not just 128. But in table 8-111,
one does find the text
Base Address of the Global Transmitter Parameter RAM Page. [...]
The user needs to allocate 128 bytes for this page. The address must
be aligned to the page size.
I've checked both rev. 7 (11/2015) and rev. 9 (05/2018) of the manual;
they both have this inconsistency (and the table numbers are the
same).
Adding a bit of debug printing, on my board the struct
ucc_geth_tx_global_pram is allocated at offset 0x880, while
the (opaque) ucc_geth_thread_data_tx gets allocated immediately
afterwards, at 0x900. So whatever the engine writes into the thread
data overlaps with the tail of the global tx pram (and devmem says
that something does get written during a simple ping).
I haven't observed any failure that could be attributed to this, but
it seems to be the kind of thing that would be extremely hard to
debug. So extend the struct definition so that we do allocate 192
bytes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b33d6ffa9 ]
currently mtype_resize() can cause oops
t = ip_set_alloc(htable_size(htable_bits));
if (!t) {
ret = -ENOMEM;
goto out;
}
t->hregion = ip_set_alloc(ahash_sizeof_regions(htable_bits));
Increased htable_bits can force htable_size() to return 0.
In own turn ip_set_alloc(0) returns not 0 but ZERO_SIZE_PTR,
so follwoing access to t->hregion should trigger an OOPS.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e6ae563c ]
If you run 'make uImage uImage.gz' with the parallel option, uImage.gz
will be created by two threads simultaneously.
This is because arch/arc/Makefile does not specify the dependency
between uImage and uImage.gz. Hence, GNU Make assumes they can be
built in parallel. One thread descends into arch/arc/boot/ to create
uImage, and another to create uImage.gz.
Please notice the same log is displayed twice in the following steps:
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig
$ make -j$(nproc) ARCH=arc uImage uImage.gz
[ snip ]
LD vmlinux
SORTTAB vmlinux
SYSMAP System.map
OBJCOPY arch/arc/boot/vmlinux.bin
OBJCOPY arch/arc/boot/vmlinux.bin
GZIP arch/arc/boot/vmlinux.bin.gz
GZIP arch/arc/boot/vmlinux.bin.gz
UIMAGE arch/arc/boot/uImage.gz
UIMAGE arch/arc/boot/uImage.gz
Image Name: Linux-5.10.0-rc4-00003-g62f23044
Created: Sun Nov 22 02:52:26 2020
Image Type: ARC Linux Kernel Image (gzip compressed)
Data Size: 2109376 Bytes = 2059.94 KiB = 2.01 MiB
Load Address: 80000000
Entry Point: 80004000
Image arch/arc/boot/uImage is ready
Image Name: Linux-5.10.0-rc4-00003-g62f23044
Created: Sun Nov 22 02:52:26 2020
Image Type: ARC Linux Kernel Image (gzip compressed)
Data Size: 2815455 Bytes = 2749.47 KiB = 2.69 MiB
Load Address: 80000000
Entry Point: 80004000
This is a race between the two threads trying to write to the same file
arch/arc/boot/uImage.gz. This is a potential problem that can generate
a broken file.
I fixed a similar problem for ARM by commit 3939f33450 ("ARM: 8418/1:
add boot image dependencies to not generate invalid images").
I highly recommend to avoid such build rules that cause a race condition.
Move the uImage rule to arch/arc/Makefile.
Another strangeness is that arch/arc/boot/Makefile compares the
timestamps between $(obj)/uImage and $(obj)/uImage.*:
$(obj)/uImage: $(obj)/uImage.$(suffix-y)
@ln -sf $(notdir $<) $@
@echo ' Image $@ is ready'
This does not work as expected since $(obj)/uImage is a symlink.
The symlink should be created in a phony target rule.
I used $(kecho) instead of echo to suppress the message
'Image arch/arc/boot/uImage is ready' when the -s option is given.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cfccb3c04 ]
The top-level boot_targets (uImage and uImage.*) should be phony
targets. They just let Kbuild descend into arch/arc/boot/ and create
files there.
If a file exists in the top directory with the same name, the boot
image will not be created.
You can confirm it by the following steps:
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig all # vmlinux will be built
$ touch uImage.gz
$ make ARCH=arc uImage.gz
CALL scripts/atomic/check-atomics.sh
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
# arch/arc/boot/uImage.gz is not created
Specify the targets as PHONY to fix this.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2712ec76a ]
arch/arc/boot/Makefile supports uImage.lzma, but you cannot do
'make uImage.lzma' because the corresponding target is missing
in arch/arc/Makefile. Add it.
I also changed the assignment operator '+=' to ':=' since this is the
only place where we expect this variable to be set.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9836720911 ]
The deb-pkg builds for ARCH=arc fail.
$ export CROSS_COMPILE=<your-arc-compiler-prefix>
$ make -s ARCH=arc defconfig
$ make ARCH=arc bindeb-pkg
SORTTAB vmlinux
SYSMAP System.map
MODPOST Module.symvers
make KERNELRELEASE=5.10.0-rc4 ARCH=arc KBUILD_BUILD_VERSION=2 -f ./Makefile intdeb-pkg
sh ./scripts/package/builddeb
cp: cannot stat 'arch/arc/boot/bootpImage': No such file or directory
make[4]: *** [scripts/Makefile.package:87: intdeb-pkg] Error 1
make[3]: *** [Makefile:1527: intdeb-pkg] Error 2
make[2]: *** [debian/rules:13: binary-arch] Error 2
dpkg-buildpackage: error: debian/rules binary subprocess returned exit status 2
make[1]: *** [scripts/Makefile.package:83: bindeb-pkg] Error 2
make: *** [Makefile:1527: bindeb-pkg] Error 2
The reason is obvious; arch/arc/Makefile sets $(boot)/bootpImage as
the default image, but there is no rule to build it.
Remove the meaningless KBUILD_IMAGE assignment so it will fallback
to the default vmlinux. With this change, you can build the deb package.
I removed the 'bootpImage' target as well. At best, it provides
'make bootpImage' as an alias of 'make vmlinux', but I do not see
much sense in doing so.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5948267a ]
With external metadata device, flush requests are not passed down to the
data device.
Fix this by submitting the flush request in dm_integrity_flush_buffers. In
order to not degrade performance, we overlap the data device flush with
the metadata device flush.
Reported-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e8fae2597 ]
close was relayered to allow passing in an async flag which
is no longer needed in this path. Remove the unneeded parameter
"flags" passed in on close.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a3b590d4b ]
When the first file is opened, ext4 samples the mountpoint of the
filesystem in 64 bytes of the super block. It does so using
strlcpy(), this means that the remaining bytes in the super block
string buffer are untouched. If the mount point before had a longer
path than the current one, it can be reconstructed.
Consider the case where the fs was mounted to "/media/johnjdeveloper"
and later to "/". The super block buffer then contains
"/\x00edia/johnjdeveloper".
This case was seen in the wild and caused confusion how the name
of a developer ands up on the super block of a filesystem used
in production...
Fix this by using strncpy() instead of strlcpy(). The superblock
field is defined to be a fixed-size char array, and it is already
marked using __nonstring in fs/ext4/ext4.h. The consumer of the field
in e2fsprogs already assumes that in the case of a 64+ byte mount
path, that s_last_mounted will not be NUL terminated.
Link: https://lore.kernel.org/r/X9ujIOJG/HqMr88R@mit.edu
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
