[ Upstream commit e841ec956e ]
Looking at the schematics, the USB Power Supply is shared between the
two USB interfaces,
If the usb0 fails to initialize, the second one won't have power.
Fixes: 5a0803bd5a ("ARM64: dts: meson-gxbb-odroidc2: Enable USB Nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 05521bd3d1 ]
With gcc 4.1.2:
drivers/mtd/spi-nor/stm32-quadspi.c: In function ‘stm32_qspi_tx_poll’:
drivers/mtd/spi-nor/stm32-quadspi.c:230: warning: ‘ret’ may be used uninitialized in this function
Indeed, if stm32_qspi_cmd.len is zero, ret will be uninitialized.
This length is passed from outside the driver using the
spi_nor.{read,write}{,_reg}() callbacks.
Several functions in drivers/mtd/spi-nor/spi-nor.c (e.g. write_enable(),
write_disable(), and erase_chip()) call spi_nor.write_reg() with a zero
length.
Fix this by returning an explicit zero on success.
Fixes: 0d43d7ab27 ("mtd: spi-nor: add driver for STM32 quad spi flash controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9931f984d ]
Under heavy load it is normal that h/w Tx queue is almost full all the time
and reclaim should be done before transmitting next packet. Warning still
should be reported as well as s/w Tx queues should be stopped in the
case when reclaim failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3993b112da ]
There are checks on fs_info in __btrfs_panic to avoid dereferencing a
null fs_info, however, there is a call to btrfs_crit that may also
dereference a null fs_info. Fix this by adding a check to see if fs_info
is null and only print the s_id if fs_info is non-null.
Detected by CoverityScan CID#401973 ("Dereference after null check")
Fixes: efe120a067 ("Btrfs: convert printk to btrfs_ and fix BTRFS prefix")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0af2c4bf5a ]
When new device is being added to seed FS, seed FS is marked writable,
but when we fail to bring in the new device, we missed to undo the
writable part. This patch fixes it.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9417ebc8a6 ]
btrfs_udpate_root can fail and it aborts the transaction, the correct
way to handle an aborted transaction is to explicitly end with
btrfs_end_transaction. Even now the code is correct since
btrfs_commit_transaction would handle an aborted transaction but this is
more of an implementation detail. So let's be explicit in handling
failure in btrfs_update_root.
Furthermore btrfs_commit_transaction can also fail and by ignoring it's
return value we could have left the in-memory copy of the root item in
an inconsistent state. So capture the error value which allows us to
correctly revert the RO/RW flags in case of commit failure.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 102ed2c5ff ]
When one of the device is missing, bbio_error() takes care of setting
the error status. And if its only IO that is pending in that stripe, it
fails to check the status of the other IO at %bbio_error before setting
the error %bi_status for the %orig_bio. Fix this by checking if
%bbio->error has exceeded the %bbio->max_errors.
Reproducer as below fdatasync error is seen intermittently.
mount -o degraded /dev/sdc /btrfs
dd status=none if=/dev/zero of=$(mktemp /btrfs/XXX) bs=4096 count=1 conv=fdatasync
dd: fdatasync failed for ‘/btrfs/LSe’: Input/output error
The reason for the intermittences of the problem is because
the following conditions have to be met, which depends on timing:
In btrfs_map_bio()
- the RAID1 the missing device has to be at %dev_nr = 1
In bbio_error()
. before bbio_error() is called the bio of the not-missing
device at %dev_nr = 0 must be completed so that the below
condition is true
if (atomic_dec_and_test(&bbio->stripes_pending)) {
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd9dde6abc ]
Upon upgrading to binutils 2.27, we found that our lz4 and gzip
compressed kernel images were significantly larger, resulting is 10ms
boot time regressions.
As noted by Rahul:
"aarch64 binaries uses RELA relocations, where each relocation entry
includes an addend value. This is similar to x86_64. On x86_64, the
addend values are also stored at the relocation offset for relative
relocations. This is an optimization: in the case where code does not
need to be relocated, the loader can simply skip processing relative
relocations. In binutils-2.25, both bfd and gold linkers did this for
x86_64, but only the gold linker did this for aarch64. The kernel build
here is using the bfd linker, which stored zeroes at the relocation
offsets for relative relocations. Since a set of zeroes compresses
better than a set of non-zero addend values, this behavior was resulting
in much better lz4 compression.
The bfd linker in binutils-2.27 is now storing the actual addend values
at the relocation offsets. The behavior is now consistent with what it
does for x86_64 and what gold linker does for both architectures. The
change happened in this upstream commit:
https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=1f56df9d0d5ad89806c24e71f296576d82344613
Since a bunch of zeroes got replaced by non-zero addend values, we see
the side effect of lz4 compressed image being a bit bigger.
To get the old behavior from the bfd linker, "--no-apply-dynamic-relocs"
flag can be used:
$ LDFLAGS="--no-apply-dynamic-relocs" make
With this flag, the compressed image size is back to what it was with
binutils-2.25.
If the kernel is using ASLR, there aren't additional runtime costs to
--no-apply-dynamic-relocs, as the relocations will need to be applied
again anyway after the kernel is relocated to a random address.
If the kernel is not using ASLR, then presumably the current default
behavior of the linker is better. Since the static linker performed the
dynamic relocs, and the kernel is not moved to a different address at
load time, it can skip applying the relocations all over again."
Some measurements:
$ ld -v
GNU ld (binutils-2.25-f3d35cf6) 2.25.51.20141117
^
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300652760 Oct 26 11:57 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 16932627 Oct 26 11:57 Image.lz4-dtb
$ ld -v
GNU ld (binutils-2.27-53dd00a1) 2.27.0.20170315
^
pre patch:
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300376208 Oct 26 11:43 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 18159474 Oct 26 11:43 Image.lz4-dtb
post patch:
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300376208 Oct 26 12:06 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 16932466 Oct 26 12:06 Image.lz4-dtb
By Siqi's measurement w/ gzip:
binutils 2.27 with this patch (with --no-apply-dynamic-relocs):
Image 41535488
Image.gz 13404067
binutils 2.27 without this patch (without --no-apply-dynamic-relocs):
Image 41535488
Image.gz 14125516
Any compression scheme should be able to get better results from the
longer runs of zeros, not just GZIP and LZ4.
10ms boot time savings isn't anything to get excited about, but users of
arm64+compression+bfd-2.27 should not have to pay a penalty for no
runtime improvement.
Reported-by: Gopinath Elanchezhian <gelanchezhian@google.com>
Reported-by: Sindhuri Pentyala <spentyala@google.com>
Reported-by: Wei Wang <wvw@google.com>
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Rahul Chaudhry <rahulchaudhry@google.com>
Suggested-by: Siqi Lin <siqilin@google.com>
Suggested-by: Stephen Hines <srhines@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: added comment to Makefile]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0338b1b393 ]
The following race condition still existed:
P1 P2
cancel_work_sync()
hci_uart_tx_wakeup()
hci_uart_write_work()
hci_uart_dequeue()
clear_bit(HCI_UART_PROTO_READY)
hci_unregister_dev(hdev)
hci_free_dev(hdev)
hu->proto->close(hu)
kfree(hu)
access to hdev and hu
Cancelling the work after clearing the HCI_UART_PROTO_READY bit avoids
this as any hci_uart_tx_wakeup() issued after the flag is cleared will
detect that and not schedule further work.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00f9203119 ]
__subn_get_opa_portinfo stores value returned by hfi1_get_ib_cfg() as
operational vls. hfi1_get_ib_cfg() returns vls_operational field in
hfi1_pportdata. The problem with this is that the value is always equal
to vls_supported field in hfi1_pportdata.
The logic to calculate operational_vls is to set value passed by FM
(in __subn_set_opa_portinfo routine). If no value is passed then
default value is stored in operational_vls.
Field actual_vls_operational is calculated on the basis of buffer
control table. Hence, modifying hfi1_get_ib_cfg() to return
actual_operational_vls when used with HFI1_IB_CFG_OP_VLS parameter
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Patel Jay P <jay.p.patel@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c157313791 ]
Currently, Cache missed IOs are identified by s->cache_miss, but actually,
there are many situations that missed IOs are not assigned a value for
s->cache_miss in cached_dev_cache_miss(), for example, a bypassed IO
(s->iop.bypass = 1), or the cache_bio allocate failed. In these situations,
it will go to out_put or out_submit, and s->cache_miss is null, which leads
bch_mark_cache_accounting() to treat this IO as a hit IO.
[ML: applied by 3-way merge]
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 330a4db89d ]
mutex_destroy does nothing most of time, but it's better to call
it to make the code future proof and it also has some meaning
for like mutex debug.
As Coly pointed out in a previous review, bcache_exit() may not be
able to handle all the references properly if userspace registers
cache and backing devices right before bch_debug_init runs and
bch_debug_init failes later. So not exposing userspace interface
until everything is ready to avoid that issue.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2394facb17 ]
The "intent_req_comp" variable is used without initialization which
results in NULL pointer dereference in qcom_glink_request_intent().
we need to initialize the completion variable before using it.
Fixes: 27b9c5b66b ("rpmsg: glink: Request for intents when unavailable")
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b3168c87c0 ]
Because the brightness and contrast controls share a register,
usbtv_s_ctrl needs to read the existing values for both controls before
inserting the new value. However, the code accidentally wrote to the
registers (from an uninitialised stack array), rather than reading them.
The user-visible effect of this was that adjusting the brightness would
also set the contrast to a random value, and vice versa -- so it wasn't
possible to correctly adjust the brightness of usbtv's video output.
Tested with an "EasyDAY" UTV007 device.
Fixes: c53a846c48 ("usbtv: add video controls")
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc555b09d8 ]
This patch fixes a deadlock caused when the jdata flag is set for
inodes that are already on the ordered write list. Since it is
on the ordered write list, log_flush calls gfs2_ordered_write which
calls filemap_fdatawrite. But since the inode had the jdata flag
set, that calls gfs2_jdata_writepages, which tries to start a new
transaction. A new transaction cannot be started because it tries
to acquire the log_flush rwsem which is already locked by the log
flush operation.
The bottom line is: We cannot switch an inode from ordered to jdata
until we eliminate any ordered data pages (via log flush) or any
log_flush operation afterward will create the circular dependency
above. So we need to flush the log before setting the diskflags to
switch the file mode, then we need to remove the inode from the
ordered writes list.
Before this patch, the log flush was done for jdata->ordered, but
that's wrong. If we're going from jdata to ordered, we don't need
to call gfs2_log_flush because the call to filemap_fdatawrite will
do it for us:
filemap_fdatawrite() -> __filemap_fdatawrite_range()
__filemap_fdatawrite_range() -> do_writepages()
do_writepages() -> gfs2_jdata_writepages()
gfs2_jdata_writepages() -> gfs2_log_flush()
This patch modifies function do_gfs2_set_flags so that if a file
has its jdata flag set, and it's already on the ordered write list,
the log will be flushed and it will be removed from the list
before setting the flag.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Acked-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e33d7c5645 ]
The scsi_debug driver incorrectly suggests there is an error with the
SCSI WRITE SAME command when the number_of_logical_blocks is greater
than 1. It will also suggest there is an error when NDOB
(no data-out buffer) is set and the number_of_logical_blocks is
greater than 0. Both are valid, fix.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 846df244eb ]
If you call ida_simple_remove(&pci_endpoint_test_ida, id) with a
negative "id" then it triggers an immediate BUG_ON(). Let's not allow
that.
Fixes: 2c156ac71c ("misc: Add host side PCI driver for PCI test function device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07209fcf33 ]
There is a particular situation when the cooling device is cpufreq and the heat
dissipation is not efficient enough where the temperature increases little by
little until reaching the critical threshold and leading to a SoC reset.
The behavior is reproducible on a hikey6220 with bad heat dissipation (eg.
stacked with other boards).
Running a simple C program doing while(1); for each CPU of the SoC makes the
temperature to reach the passive regulation trip point and ends up to the
maximum allowed temperature followed by a reset.
This issue has been also reported by running the libhugetlbfs test suite.
What is observed is a ping pong between two cpu frequencies, 1.2GHz and 900MHz
while the temperature continues to grow.
It appears the step wise governor calls get_target_state() the first time with
the throttle set to true and the trend to 'raising'. The code selects logically
the next state, so the cpu frequency decreases from 1.2GHz to 900MHz, so far so
good. The temperature decreases immediately but still stays greater than the
trip point, then get_target_state() is called again, this time with the
throttle set to true *and* the trend to 'dropping'. From there the algorithm
assumes we have to step down the state and the cpu frequency jumps back to
1.2GHz. But the temperature is still higher than the trip point, so
get_target_state() is called with throttle=1 and trend='raising' again, we jump
to 900MHz, then get_target_state() is called with throttle=1 and
trend='dropping', we jump to 1.2GHz, etc ... but the temperature does not
stabilizes and continues to increase.
[ 237.922654] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 237.922678] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 237.922690] thermal cooling_device0: cur_state=0
[ 237.922701] thermal cooling_device0: old_target=0, target=1
[ 238.026656] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 238.026680] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1
[ 238.026694] thermal cooling_device0: cur_state=1
[ 238.026707] thermal cooling_device0: old_target=1, target=0
[ 238.134647] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 238.134667] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 238.134679] thermal cooling_device0: cur_state=0
[ 238.134690] thermal cooling_device0: old_target=0, target=1
In this situation the temperature continues to increase while the trend is
oscillating between 'dropping' and 'raising'. We need to keep the current state
untouched if the throttle is set, so the temperature can decrease or a higher
state could be selected, thus preventing this oscillation.
Keeping the next_target untouched when 'throttle' is true at 'dropping' time
fixes the issue.
The following traces show the governor does not change the next state if
trend==2 (dropping) and throttle==1.
[ 2306.127987] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2306.128009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 2306.128021] thermal cooling_device0: cur_state=0
[ 2306.128031] thermal cooling_device0: old_target=0, target=1
[ 2306.231991] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2306.232016] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=1
[ 2306.232030] thermal cooling_device0: cur_state=1
[ 2306.232042] thermal cooling_device0: old_target=1, target=1
[ 2306.335982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2306.336006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=1
[ 2306.336021] thermal cooling_device0: cur_state=1
[ 2306.336034] thermal cooling_device0: old_target=1, target=1
[ 2306.439984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2306.440008] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0
[ 2306.440022] thermal cooling_device0: cur_state=1
[ 2306.440034] thermal cooling_device0: old_target=1, target=0
[ ... ]
After a while, if the temperature continues to increase, the next state becomes
2 which is 720MHz on the hikey. That results in the temperature stabilizing
around the trip point.
[ 2455.831982] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2455.832006] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=0
[ 2455.832019] thermal cooling_device0: cur_state=1
[ 2455.832032] thermal cooling_device0: old_target=1, target=1
[ 2455.935985] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2455.936013] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0
[ 2455.936027] thermal cooling_device0: cur_state=1
[ 2455.936040] thermal cooling_device0: old_target=1, target=1
[ 2456.043984] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=0,throttle=1
[ 2456.044009] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=0,throttle=0
[ 2456.044023] thermal cooling_device0: cur_state=1
[ 2456.044036] thermal cooling_device0: old_target=1, target=1
[ 2456.148001] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=1,throttle=1
[ 2456.148028] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=1,throttle=1
[ 2456.148042] thermal cooling_device0: cur_state=1
[ 2456.148055] thermal cooling_device0: old_target=1, target=2
[ 2456.252009] thermal thermal_zone0: Trip0[type=1,temp=65000]:trend=2,throttle=1
[ 2456.252041] thermal thermal_zone0: Trip1[type=1,temp=75000]:trend=2,throttle=0
[ 2456.252058] thermal cooling_device0: cur_state=2
[ 2456.252075] thermal cooling_device0: old_target=2, target=1
IOW, this change is needed to keep the state for a cooling device if the
temperature trend is oscillating while the temperature increases slightly.
Without this change, the situation above leads to a catastrophic crash by a
hardware reset on hikey. This issue has been reported to happen on an OMAP
dra7xx also.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22ef01a203 ]
Below is the call trace of tegra210_init_pllu() function:
start_kernel()
-> time_init()
--> of_clk_init()
---> tegra210_clock_init()
----> tegra210_pll_init()
-----> tegra210_init_pllu()
Because the preemption is disabled in the start_kernel before calling
time_init, tegra210_init_pllu is actually in an atomic context while
it includes a readl_relaxed_poll_timeout that might sleep.
So this patch just changes this readl_relaxed_poll_timeout() to its
atomic version.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e3d02bbaf ]
When the hw queue is busy, we shouldn't take requests from the scheduler
queue any more, otherwise it is difficult to do IO merge.
This patch fixes the awful IO performance on some SCSI devices(lpfc,
qla2xxx, ...) when mq-deadline/kyber is used by not taking requests if
hw queue is busy.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9917fbcfa2 ]
if output->wm_num is bigger than 2, the value for reg is
not initialized, as warned by smatch:
drivers/media/platform/qcom/camss-8x16/camss-vfe.c:633 vfe_set_xbar_cfg() error: uninitialized symbol 'reg'.
drivers/media/platform/qcom/camss-8x16/camss-vfe.c:637 vfe_set_xbar_cfg() error: uninitialized symbol 'reg'.
That shouldn't happen in practice, so add a logic that will
break the loop if i > 1, fixing the warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c68ee58d9e ]
On i.MX6 SoCs without VPU (in my case MCIMX6D4AVT10AC), the hdmi driver
fails to probe:
[ 2.540030] dwhdmi-imx 120000.hdmi: Unsupported HDMI controller
(0000:00:00)
[ 2.548199] imx-drm display-subsystem: failed to bind 120000.hdmi
(ops dw_hdmi_imx_ops): -19
[ 2.557403] imx-drm display-subsystem: master bind failed: -19
That's because hdmi_isfr's parent, video_27m, is not correctly ungated.
As explained in commit 5ccc248cc5 ("ARM: imx6q: clk: Add support for
mipi_core_cfg clock as a shared clock gate"), video_27m is gated by
CCM_CCGR3[CG8].
On i.MX6 SoCs with VPU, the hdmi is working thanks to the
CCM_CMEOR[mod_en_ov_vpu] bit which makes the video_27m ungated whatever
is in CCM_CCGR3[CG8]. The issue can be reproduced by setting
CCMEOR[mod_en_ov_vpu] to 0.
Make the HDMI work in every case by setting hdmi_isfr's parent to
mipi_core_cfg.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c955bf3998 ]
Since the previous setup always sets the PLL using crystal 26MHz, this
doesn't always happen in every MediaTek platform. So the patch added
flexibility for assigning extra member for determining the PLL source
clock.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4004a9870b ]
Commit 74e1e498e8 ("staging: rtl8188eu: fix comments with lines over 80
characters") not only changed comments but also changed an if check:
-if (pmlmepriv->cur_network.join_res != true) {
+if (!(pmlmepriv->cur_network.join_res)) {
This is not equivalent as join_res is an int and can have values such
as -2 and -3.
Note for the next time, please only make one type of changes in a single
clean-up commit.
Fixes: 74e1e498e8 ("staging: rtl8188eu: fix comments with lines over 80 ...")
Cc: Juliana Rodrigues <juliana.orod@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b39cabb2a ]
This patch fixes a bug for ethtool's get_link_ksettings().
The advertising for autoneg is always added to advertised_caps
whether autoneg is enable or disable. This patch fixes it.
Fixes: 496d03e (net: hns3: Add Ethtool support to HNS3 driver)
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 592e254502 ]
_calc_vm_trans() does not handle the situation when some of the passed
flags are 0 (which can happen if these VM flags do not make sense for
the architecture). Improve the _calc_vm_trans() macro to return 0 in
such situation. Since all passed flags are constant, this does not add
any runtime overhead.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 350976ae21 ]
On truncate down, if new size is not block size aligned, we zero the
rest of block to avoid exposing stale data to user, and
iomap_truncate_page() skips zeroing if the range is already in
unwritten state or a hole. Then we writeback from on-disk i_size to
the new size if this range hasn't been written to disk yet, and
truncate page cache beyond new EOF and set in-core i_size.
The problem is that we could write data between di_size and newsize
before removing the page cache beyond newsize, as the extents may
still be in unwritten state right after a buffer write. As such, the
page of data that newsize lies in has not been zeroed by page cache
invalidation before it is written, and xfs_do_writepage() hasn't
triggered it's "zero data beyond EOF" case because we haven't
updated in-core i_size yet. Then a subsequent mmap read could see
non-zeros past EOF.
I occasionally see this in fsx runs in fstests generic/112, a
simplified fsx operation sequence is like (assuming 4k block size
xfs):
fallocate 0x0 0x1000 0x0 keep_size
write 0x0 0x1000 0x0
truncate 0x0 0x800 0x1000
punch_hole 0x0 0x800 0x800
mapread 0x0 0x800 0x800
where fallocate allocates unwritten extent but doesn't update
i_size, buffer write populates the page cache and extent is still
unwritten, truncate skips zeroing page past new EOF and writes the
page to disk, punch_hole invalidates the page cache, at last mapread
reads the block back and sees non-zero beyond EOF.
Fix it by moving truncate_setsize() to before writeback so the page
cache invalidation zeros the partial page at the new EOF. This also
triggers "zero data beyond EOF" in xfs_do_writepage() at writeback
time, because newsize has been set and page straddles the newsize.
Also fixed the wrong 'end' param of filemap_write_and_wait_range()
call while we're at it, the 'end' is inclusive and should be
'newsize - 1'.
Suggested-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <eguan@redhat.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b92b4fb5c1 ]
The extent of pages specified when applying a reserved region should
include up to the last page of the range, but not the page following
the range.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Fixes: 8d54d6c8b8 ('iommu/amd: Implement apply_dm_region call-back')
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39b4954c0a ]
MD's rdev_set_badblocks() expects that badblocks_set() returns 1 if
badblocks are disabled, otherwise, rdev_set_badblocks() will record
superblock changes and return success in that case and md will fail to
report an IO error which it should.
This bug has existed since badblocks were introduced in commit
9e0e252a04 ("badblocks: Add core badblock management code").
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 594e25e734 ]
The function fd_execute_unmap() in target_core_file.c calles
ret = file->f_op->fallocate(file, mode, pos, len);
Some filesystems implement fallocate() to return error if
length is zero (e.g. btrfs) but according to SCSI Block
Commands spec UNMAP should return success for zero length.
Signed-off-by: Jiang Yi <jiangyilism@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24528f089d ]
When is pr_reg->isid_present_at_reg is false,this function should return.
This fixes a regression originally introduced by:
commit d2843c173e
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:40:55 2013 -0700
target: Alter core_pr_dump_initiator_port for ease of use
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6eaf69e4ec ]
Certain behavior of the initiator can cause the target driver to
send both a reject and a SCSI response. If that happens two
target_put_sess_cmd() calls will occur without the command having
been removed from conn_cmd_list. In other words, conn_cmd_list
will get corrupted once the freed memory is reused. Although the
Linux kernel can detect list corruption if list debugging is
enabled, in this case the context in which list corruption is
detected is not related to the context that caused list corruption.
Hence add WARN_ON() statements that report the context that is
causing list corruption.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cc8cbbc88 ]
For PUNIT device, ISPDRIVER_IPC and GTDDRIVER_IPC resources are not
mandatory. So when PMC IPC driver creates a PUNIT device, if these
resources are not available then it creates dummy resource entries for
these missing resources. But during PUNIT device probe, doing ioremap on
these dummy resources generates following warning messages.
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
This patch fixes this issue by adding extra check for resource size
before performing ioremap operation.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b8f89fea59 ]
When a vdevice is DLPAR removed from the system the vio subsystem
doesn't bother unmapping the virq from the irq_domain. As a result we
have a virq mapped to a hardware irq that is no longer valid for the
irq_domain. A side effect is that we are left with /proc/irq/<irq#>
affinity entries, and attempts to modify the smp_affinity of the irq
will fail.
In the following observed example the kernel log is spammed by
ics_rtas_set_affinity errors after the removal of a VSCSI adapter.
This is a result of irqbalance trying to adjust the affinity every 10
seconds.
rpadlpar_io: slot U8408.E8E.10A7ACV-V5-C25 removed
ics_rtas_set_affinity: ibm,set-xive irq=655385 returns -3
ics_rtas_set_affinity: ibm,set-xive irq=655385 returns -3
This patch fixes the issue by calling irq_dispose_mapping() on the
virq of the viodev on unregister.
Fixes: f2ab621996 ("powerpc/pseries: Add PFO support to the VIO bus")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71e24d7731 ]
The current code checks the completion map to look for the first token
that is complete. In some cases, a completion can come in but the
token can still be on lease to the caller processing the completion.
If this completed but unreleased token is the first token found in the
bitmap by another tasks trying to acquire a token, then the
__test_and_set_bit call will fail since the token will still be on
lease. The acquisition will then fail with an EBUSY.
This patch reorganizes the acquisition code to look at the
opal_async_token_map for an unleased token. If the token has no lease
it must have no outstanding completions so we should never see an
EBUSY, unless we have leased out too many tokens. Since
opal_async_get_token_inrerruptible is protected by a semaphore, we
will practically never see EBUSY anymore.
Fixes: 8d72482322 ("powerpc/powernv: Infrastructure to support OPAL async completion")
Signed-off-by: William A. Kennington III <wak@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5504f724c ]
Information about ipvs in different network namespace can be seen via procfs.
How to reproduce:
# ip netns add ns01
# ip netns add ns02
# ip netns exec ns01 ip a add dev lo 127.0.0.1/8
# ip netns exec ns02 ip a add dev lo 127.0.0.1/8
# ip netns exec ns01 ipvsadm -A -t 10.1.1.1:80
# ip netns exec ns02 ipvsadm -A -t 10.1.1.2:80
The ipvsadm displays information about its own network namespace only.
# ip netns exec ns01 ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 10.1.1.1:80 wlc
# ip netns exec ns02 ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 10.1.1.2:80 wlc
But I can see information about other network namespace via procfs.
# ip netns exec ns01 cat /proc/net/ip_vs
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 0A010101:0050 wlc
TCP 0A010102:0050 wlc
# ip netns exec ns02 cat /proc/net/ip_vs
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 0A010102:0050 wlc
Signed-off-by: KUWAZAWA Takuya <albatross0@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
