[ Upstream commit 82b34b0800 ]
The Qualcomm PCI bridge device (Device ID 0x010e) found in chipsets such as
SC8280XP used in Lenovo Thinkpad X13s, does not set the Command Completed
bit unless writes to the Slot Command register change "Control" bits.
This results in timeouts like below during boot and resume from suspend:
pcieport 0002:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
...
pcieport 0002:00:00.0: pciehp: Timeout on hotplug command 0x13f1 (issued 107724 msec ago)
Add the device to the Command Completed quirk to mark commands "completed"
immediately unless they change the "Control" bits.
Link: https://lore.kernel.org/r/20230213144922.89982-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7180c1d086 ]
Previously we distributed spare resources only upon hot-add, so if the
initial root bus scan found devices that had not been fully configured by
the BIOS, we allocated only enough resources to cover what was then
present. If some of those devices were hotplug bridges, we did not leave
any additional resource space for future expansion.
Distribute the available resources for root buses, too, to make this work
the same way as the normal hotplug case.
A previous commit to do this was reverted due to a regression reported by
Jonathan Cameron:
e96e27fc6f ("PCI: Distribute available resources for root buses, too")
5632e2beaf ("Revert "PCI: Distribute available resources for root buses, too"")
This commit changes pci_bridge_resources_not_assigned() to work with
bridges that do not have all the resource windows programmed by the boot
firmware (previously we expected all I/O, memory and prefetchable memory
were programmed).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216000
Link: https://lore.kernel.org/r/20220905080232.36087-5-mika.westerberg@linux.intel.com
Link: https://lore.kernel.org/r/20230131092405.29121-4-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9db0b9b6a1 ]
A PCI bridge may reside on a bus with other devices as well. The resource
distribution code does not take this into account and therefore it expands
the bridge resource windows too much, not leaving space for the other
devices (or functions of a multifunction device). This leads to an issue
that Jonathan reported when running QEMU with the following topology (QEMU
parameters):
-device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2 \
-device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \
-device e1000,bus=root_port13,addr=0.1 \
-device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3 \
-device e1000,bus=fun1
The first e1000 NIC here is another function in the switch upstream port.
This leads to following errors:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04]
pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04]
pci 0000:02:00.1: BAR 0: failed to assign [mem size 0x00020000]
e1000 0000:02:00.1: can't ioremap BAR 0: [??? 0x00000000 flags 0x0]
Fix this by taking into account bridge windows, device BARs and SR-IOV PF
BARs on the bus (PF BARs include space for VF BARS so only account PF
BARs), including the ones belonging to bridges themselves if it has any.
Link: https://lore.kernel.org/linux-pci/20221014124553.0000696f@huawei.com/
Link: https://lore.kernel.org/linux-pci/6053736d-1923-41e7-def9-7585ce1772d9@ixsystems.com/
Link: https://lore.kernel.org/r/20230131092405.29121-3-mika.westerberg@linux.intel.com
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: Alexander Motin <mav@ixsystems.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce33e64c17 ]
The allocation of PageBuffer is 512 bytes in size, but the dereferencing
of struct ms_bootblock_idi (also size 512) happens at a calculated offset
within the allocation, which means the object could potentially extend
beyond the end of the allocation. Avoid this case by just allocating
enough space to catch any accesses beyond the end. Seen with GCC 13:
../drivers/usb/storage/ene_ub6250.c: In function 'ms_lib_process_bootblock':
../drivers/usb/storage/ene_ub6250.c:1050:44: warning: array subscript 'struct ms_bootblock_idi[0]' is partly outside array bounds of 'unsigned char[512]' [-Warray-bounds=]
1050 | if (le16_to_cpu(idi->wIDIgeneralConfiguration) != MS_IDI_GENERAL_CONF)
| ^~
../include/uapi/linux/byteorder/little_endian.h:37:51: note: in definition of macro '__le16_to_cpu'
37 | #define __le16_to_cpu(x) ((__force __u16)(__le16)(x))
| ^
../drivers/usb/storage/ene_ub6250.c:1050:29: note: in expansion of macro 'le16_to_cpu'
1050 | if (le16_to_cpu(idi->wIDIgeneralConfiguration) != MS_IDI_GENERAL_CONF)
| ^~~~~~~~~~~
In file included from ../drivers/usb/storage/ene_ub6250.c:5:
In function 'kmalloc',
inlined from 'ms_lib_process_bootblock' at ../drivers/usb/storage/ene_ub6250.c:942:15:
../include/linux/slab.h:580:24: note: at offset [256, 512] into object of size 512 allocated by 'kmalloc_trace'
580 | return kmalloc_trace(
| ^~~~~~~~~~~~~~
581 | kmalloc_caches[kmalloc_type(flags)][index],
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
582 | flags, size);
| ~~~~~~~~~~~~
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230204183546.never.849-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fbd2cda92 ]
Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:
In function 'xhci_mvebu_mbus_config',
inlined from 'xhci_mvebu_mbus_init_quirk' at ../drivers/usb/host/xhci-mvebu.c:66:2:
../drivers/usb/host/xhci-mvebu.c:37:28: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
37 | writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
| ~~^~~~~~
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230204183651.never.663-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b3517f88f ]
Except for isochronous-configured devices, software may set
Max_Read_Request_Size (MRRS) to any value up to 4096. If a device issues a
read request with size greater than the completer's Max_Payload_Size (MPS),
the completer is required to break the response into multiple completions.
Instead of correctly responding with multiple completions to a large read
request, some LS7A Root Ports respond with a Completer Abort. To prevent
this, the MRRS must be limited to an implementation-specific value.
The OS cannot detect that value, so rely on BIOS to configure MRRS before
booting, and quirk the Root Ports so we never set an MRRS larger than that
BIOS value for any downstream device.
N.B. Hot-added devices are not configured by BIOS, and they power up with
MRRS = 512 bytes, so these devices will be limited to 512 bytes. If the
LS7A limit is smaller, those hot-added devices may not work correctly, but
per [1], hotplug is not supported with this chipset revision.
[1] https://lore.kernel.org/r/073638a7-ae68-2847-ac3d-29e5e760d6af@loongson.cn
[bhelgaas: commit log]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216884
Link: https://lore.kernel.org/r/20230201043018.778499-3-chenhuacai@loongson.cn
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8f71b49ee ]
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order.
Co-developed-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Isaac True <isaac.true@canonical.com>
Link: https://lore.kernel.org/r/20221130105529.698385-1-isaac.true@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4c81db5cf ]
LPUART IP has a bug that it treats the CTS as higher priority than the
break signal, which cause the break signal sending through UARTCTRL_SBK
may impacted by the CTS input if the HW flow control is enabled.
Add this workaround patch to fix the IP bug, we can disable CTS before
asserting SBK to avoid any interference from CTS, and re-enable it when
break off.
Such as for the bluetooth chip power save feature, host can let the BT
chip get into sleep state by sending a UART break signal, and wake it up
by turning off the UART break. If the BT chip enters the sleep mode
successfully, it will pull up the CTS line, if the BT chip is woken up,
it will pull down the CTS line. If without this workaround patch, the
UART TX pin cannot send the break signal successfully as it affected by
the BT CTS pin. After adding this patch, the BT power save feature can
work well.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 198102c910 ]
The cacheinfo sets up the shared_cpu_map by checking whether the caches
with the same index are shared between CPUs. However, this will trigger
slab-out-of-bounds access if the CPUs do not have the same cache hierarchy.
Another problem is the mismatched shared_cpu_map when the shared cache does
not have the same index between CPUs.
CPU0 I D L3
index 0 1 2 x
^ ^ ^ ^
index 0 1 2 3
CPU1 I D L2 L3
This patch checks each cache is shared with all caches on other CPUs.
Reviewed-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Link: https://lore.kernel.org/r/20230117105133.4445-2-yongxuan.wang@sifive.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b839212988 ]
The memcpy() in uvc_video_decode_meta() intentionally copies across the
length and flags members and into the trailing buf flexible array.
Split the copy so that the compiler can better reason about (the lack
of) buffer overflows here. Avoid the run-time false positive warning:
memcpy: detected field-spanning write (size 12) of single field "&meta->length" at drivers/media/usb/uvc/uvc_video.c:1355 (size 1)
Additionally fix a typo in the documentation for struct uvc_meta_buf.
Reported-by: ionut_n2001@yahoo.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216810
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4867bb590a ]
On a Webcam from Quanta, we see the following error.
usb 3-5: New USB device found, idVendor=0408, idProduct=30d2, bcdDevice= 0.03
usb 3-5: New USB device strings: Mfr=3, Product=1, SerialNumber=2
usb 3-5: Product: USB2.0 HD UVC WebCam
usb 3-5: Manufacturer: Quanta
usb 3-5: SerialNumber: 0x0001
...
uvcvideo: Found UVC 1.10 device USB2.0 HD UVC WebCam (0408:30d2)
uvcvideo: Failed to initialize entity for entity 5
uvcvideo: Failed to register entities (-22).
The Webcam reports an entity of type UVC_VC_EXTENSION_UNIT. It reports a
string index of '7' associated with that entity. The attempt to read that
string from the camera fails with error -32 (-EPIPE). usb_string() returns
that error, but it is ignored. As result, the entity name is empty. This
later causes v4l2_device_register_subdev() to return -EINVAL, and no
entities are registered as result.
While this appears to be a firmware problem with the camera, the kernel
should still handle the situation gracefully. To do that, check the return
value from usb_string(). If it reports an error, assign the entity's
default name.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50459f103e ]
The V4L2 core overwrites format descriptions in v4l_fill_fmtdesc(),
there's no need to manually set the descriptions in the driver. This
prepares for removal of the format descriptions from the uvc_fmts table.
Unlike V4L2, UVC makes a distinction between the SD-DV, SDL-DV and HD-DV
formats. It also indicates whether the DV format uses 50Hz or 60Hz. This
information is parsed by the driver to construct a format name string
that is printed in a debug message, but serves no other purpose as V4L2
has a single V4L2_PIX_FMT_DV pixel format that covers all those cases.
As the information is available in the UVC descriptors, and thus
accessible to users with lsusb if they really care, don't log it in a
debug message and drop the format name string to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8133844a8f ]
It is questionable to allow a PCI bridge to go into D3 if it has _S0W
returning D2 or a shallower power state, so modify acpi_pci_bridge_d3(() to
always take the return value of _S0W for the target bridge into account.
That is, make it return 'false' if _S0W returns D2 or a shallower power
state for the target bridge regardless of its ancestor Root Port
properties. Of course, this also causes 'false' to be returned if the Root
Port itself is the target and its _S0W returns D2 or a shallower power
state.
However, still allow bridges without _S0W that are power-manageable via
ACPI to enter D3 to retain the current code behavior in that case.
This fixes problems where a hotplug notification is missed because a bridge
is in D3. That means hot-added devices such as USB4 docks (and the devices
they contain) and Thunderbolt 3 devices may not work.
Link: https://lore.kernel.org/linux-pci/20221031223356.32570-1-mario.limonciello@amd.com/
Link: https://lore.kernel.org/r/12155458.O9o76ZdvQC@kreacher
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
