Since the introduction of regulator->enable_count, a driver that did
an exclusive get on an already-enabled regulator would end up with
enable_count initialized to 0 but rdev->use_count initialized to 1.
With that starting point the regulator is effectively stuck enabled,
because if the driver attempted to disable it it would fail the
enable_count underflow check in _regulator_handle_consumer_disable().
The EXCLUSIVE_GET path in _regulator_get() now initializes
enable_count along with rdev->use_count so that the regulator can be
disabled without underflowing the former.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 5451781dad ("regulator: core: Only count load for enabled consumers")
Link: https://lore.kernel.org/r/20220505043152.12933-1-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>:
Extend the RPMH regulator bindings with minor fixes and adding narrow supply
matching.
The RPMH regulator binding covers several devices with different
regulator supplies, so it uses patterns matching broad range of these
supplies. This works fine but is not specific and might miss actual
mistakes when a wrong supply property is used for given variant.
Describe the supplies depending on the compatible, using a defs-allOf
method.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220426105501.73200-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6315 PMIC dt-binding should enforce that one of the valid
regulator-compatible is set in each regulator node. However it was
mistakenly matching against regulator-name instead.
Fix the typo. This not only fixes the compatible verification, but also
lifts the regulator-name restriction, so that more meaningful names can
be set for each platform.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220429201325.2205799-1-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-4-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulators block of SM5703 controls several voltage regulators which
are used to power various components. There are 3 LDO outputs ranging
from 1.5 to 3.3V, a buck regulator ranging from 1V to 3V, two fixed
voltage LDO regulators for powering the USB devices and one high-power
fixed voltage LDO line (actually two lines) meant to power high-power
USB devices.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220423085319.483524-6-markuss.broks@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The binding and driver duplicated regulator core feature of controlling
regulators with GPIOs (of_parse_cb + ena_gpiod) and created its own
enable-gpios property with multiple GPIOs.
This is a less preferred way, because enable-gpios should enable only one
element, not multiple. It also duplicates existing solution.
Deprecate the original 'enable-gpios' and add per-regulator property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220425072455.27356-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
These delays can be relatively large (e.g., hundreds of microseconds to
several milliseconds on RK3399 Gru systems). Per
Documentation/timers/timers-howto.rst, that should usually use a
sleeping delay. Let's use the existing regulator delay helper to handle
both large and small delays appropriately. This avoids burning a bunch
of CPU time and hurting scheduling latencies when hitting regulators a
lot (e.g., during cpufreq).
The sleep vs. delay issue choice has been made differently over time --
early versions of RK3399 Gru PWM-regulator support used usleep_range()
in pwm-regulator.c. More of this got moved into the regulator core,
in commits like:
73e705bf81 regulator: core: Add set_voltage_time op
At the same time, the sleep turned into a delay.
It's OK to sleep in _regulator_do_set_voltage(), as we aren't in an
atomic context. (All our callers grab various mutexes already.)
I avoid using fsleep() because it uses a usleep_range() of [N to N*2],
and usleep_range() very commonly biases to the high end of the range. We
don't want to double the expected delay, especially for long delays.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220420141511.v2.2.If0fc61a894f537b052ca41572aff098cf8e7e673@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
KASAN report slab-out-of-bounds in __regmap_init as follows:
BUG: KASAN: slab-out-of-bounds in __regmap_init drivers/base/regmap/regmap.c:841
Read of size 1 at addr ffff88803678cdf1 by task xrun/9137
CPU: 0 PID: 9137 Comm: xrun Tainted: G W 5.18.0-rc2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0xe8/0x15a lib/dump_stack.c:88
print_report.cold+0xcd/0x69b mm/kasan/report.c:313
kasan_report+0x8e/0xc0 mm/kasan/report.c:491
__regmap_init+0x4540/0x4ba0 drivers/base/regmap/regmap.c:841
__devm_regmap_init+0x7a/0x100 drivers/base/regmap/regmap.c:1266
__devm_regmap_init_i2c+0x65/0x80 drivers/base/regmap/regmap-i2c.c:394
da9121_i2c_probe+0x386/0x6d1 drivers/regulator/da9121-regulator.c:1039
i2c_device_probe+0x959/0xac0 drivers/i2c/i2c-core-base.c:563
This happend when da9121 device is probe by da9121_i2c_id, but with
invalid dts. Thus, chip->subvariant_id is set to -EINVAL, and later
da9121_assign_chip_model() will access 'regmap' without init it.
Fix it by return -EINVAL from da9121_assign_chip_model() if
'chip->subvariant_id' is invalid.
Fixes: f3fbd5566f ("regulator: da9121: Add device variants")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Adam Ward <Adam.Ward.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20220421090335.1876149-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Johnson Wang <johnson.wang@mediatek.com>:
This patchset adds support for MediaTek PMIC MT6366.
MT6366 is the primary PMIC for MT8186 and probably other SOCs.
Merge series from Johnson Wang <johnson.wang@mediatek.com>:
This patchset adds support for MediaTek PMIC MT6366.
MT6366 is the primary PMIC for MT8186 and probably other SOCs.
While we currently assume that regulators with no control available are
just uncontionally enabled this isn't always as clearly displayed to
users as is desirable, for example the code for disabling unused
regulators will log that it is about to disable them. Clean this up a
bit by setting always_on during constraint evaluation if we have no
available mechanism for controlling the regualtor so things that check
the constraint will do the right thing.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220325144637.1543496-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull more tracing updates from Steven Rostedt:
- Rename the staging files to give them some meaning. Just
stage1,stag2,etc, does not show what they are for
- Check for NULL from allocation in bootconfig
- Hold event mutex for dyn_event call in user events
- Mark user events to broken (to work on the API)
- Remove eBPF updates from user events
- Remove user events from uapi header to keep it from being installed.
- Move ftrace_graph_is_dead() into inline as it is called from hot
paths and also convert it into a static branch.
* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Move user_events.h temporarily out of include/uapi
ftrace: Make ftrace_graph_is_dead() a static branch
tracing: Set user_events to BROKEN
tracing/user_events: Remove eBPF interfaces
tracing/user_events: Hold event_mutex during dyn_event_add
proc: bootconfig: Add null pointer check
tracing: Rename the staging files for trace_events
Pull clk fix from Stephen Boyd:
"A single revert to fix a boot regression seen when clk_put() started
dropping rate range requests. It's best to keep various systems
booting so we'll kick this out and try again next time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Revert "clk: Drop the rate range on clk_put()"
Pull x86 fixes from Thomas Gleixner:
"A set of x86 fixes and updates:
- Make the prctl() for enabling dynamic XSTATE components correct so
it adds the newly requested feature to the permission bitmap
instead of overwriting it. Add a selftest which validates that.
- Unroll string MMIO for encrypted SEV guests as the hypervisor
cannot emulate it.
- Handle supervisor states correctly in the FPU/XSTATE code so it
takes the feature set of the fpstate buffer into account. The
feature sets can differ between host and guest buffers. Guest
buffers do not contain supervisor states. So far this was not an
issue, but with enabling PASID it needs to be handled in the buffer
offset calculation and in the permission bitmaps.
- Avoid a gazillion of repeated CPUID invocations in by caching the
values early in the FPU/XSTATE code.
- Enable CONFIG_WERROR in x86 defconfig.
- Make the X86 defconfigs more useful by adapting them to Y2022
reality"
* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/xstate: Consolidate size calculations
x86/fpu/xstate: Handle supervisor states in XSTATE permissions
x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
x86/fpu: Cache xfeature flags from CPUID
x86/fpu/xsave: Initialize offset/size cache early
x86/fpu: Remove unused supervisor only offsets
x86/fpu: Remove redundant XCOMP_BV initialization
x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
x86/config: Make the x86 defconfigs a bit more usable
x86/defconfig: Enable WERROR
selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation
