[ Upstream commit 1743e5f600 ]
nvme_mpath_remove_disk is called after del_gendisk, at which point a
blk_mark_disk_dead call doesn't make any sense.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 224a876e37 ]
gcc with W=1 and ! CONFIG_NF_NAT
net/netfilter/nf_conntrack_netlink.c:3463:32: error:
‘exp_nat_nla_policy’ defined but not used [-Werror=unused-const-variable=]
3463 | static const struct nla_policy exp_nat_nla_policy[CTA_EXPECT_NAT_MAX+1] = {
| ^~~~~~~~~~~~~~~~~~
net/netfilter/nf_conntrack_netlink.c:2979:33: error:
‘any_addr’ defined but not used [-Werror=unused-const-variable=]
2979 | static const union nf_inet_addr any_addr;
| ^~~~~~~~
These variables use is controlled by CONFIG_NF_NAT, so should their definitions.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 212457ccbd ]
clang warns about an unpacked structure inside of a packed one:
drivers/net/wireless/broadcom/b43/b43.h:654:4: error: field data within 'struct b43_iv' is less aligned than 'union (unnamed union at /home/arnd/arm-soc/drivers/net/wireless/broadcom/b43/b43.h:651:2)' and is usually due to 'struct b43_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
The problem here is that the anonymous union has the default alignment
from its members, apparently because the original author mixed up the
placement of the __packed attribute by placing it next to the struct
member rather than the union definition. As the struct itself is
also marked as __packed, there is no need to mark its members, so just
move the annotation to the inner type instead.
As Michael noted, the same problem is present in b43legacy, so
change both at the same time.
Acked-by: Michael Büsch <m@bues.ch>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/oe-kbuild-all/202305160749.ay1HAoyP-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516183442.536589-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20429444e6 ]
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a
probability of failure, which shows "authentication with ... timed out".
Through debugging, it was found that the RCR register has been inexplicably
modified to an incorrect value, resulting in the nic not being able to
receive authenticated frames.
To fix this problem, add regrcr in rtl8xxxu_priv struct, and store
the RCR value every time the register is written, and use it the next
time the register need to be modified.
Signed-off-by: Yun Lu <luyun@kylinos.cn>
Link: https://lore.kernel.org/all/20230427020512.1221062-1-luyun_611@163.com
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512012055.2990472-1-luyun_611@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a33239be2d ]
When SMT thread CPUs are added to CPU masks the nr_cpu_ids
limit is not checked and could be exceeded. This leads to
a warning for example if CONFIG_DEBUG_PER_CPU_MAPS is set
and the command line parameter nr_cpus is set to 1.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 844cf829e5 ]
Key blobs for the IOCTLs PKEY_KBLOB2PROTK[23] may contain clear key
material. Zeroize the copies of these keys in kernel memory after
creating the protected key.
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 280a8ab817 ]
If the device node of dvb_ca_en50221 is open() and the
device is disconnected, a UAF may occur when calling
close() on the device node.
The root cause is that wake_up() and wait_event() for
dvbdev->wait_queue are not implemented.
So implement wait_event() function in dvb_ca_en50221_release()
and add 'remove_mutex' which prevents race condition
for 'ca->exit'.
[mchehab: fix a checkpatch warning]
Link: https://lore.kernel.org/linux-media/20221121063308.GA33821@ubuntu
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 627bb528b0 ]
dvb_register_device() dynamically allocates fops with kmemdup()
to set the fops->owner.
And these fops are registered in 'file->f_ops' using replace_fops()
in the dvb_device_open() process, and kfree()d in dvb_free_device().
However, it is not common to use dynamically allocated fops instead
of 'static const' fops as an argument of replace_fops(),
and UAF may occur.
These UAFs can occur on any dvb type using dvb_register_device(),
such as dvb_dvr, dvb_demux, dvb_frontend, dvb_net, etc.
So, instead of kfree() the fops dynamically allocated in
dvb_register_device() in dvb_free_device() called during the
.disconnect() process, kfree() it collectively in exit_dvbdev()
called when the dvbdev.c module is removed.
Link: https://lore.kernel.org/linux-media/20221117045925.14297-4-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4172385b0c ]
A race condition may occur between the .disconnect function, which
is called when the device is disconnected, and the dvb_device_open()
function, which is called when the device node is open()ed.
This results in several types of UAFs.
The root cause of this is that you use the dvb_device_open() function,
which does not implement a conditional statement
that checks 'dvbnet->exit'.
So, add 'remove_mutex` to protect 'dvbnet->exit' and use
locked_dvb_net_open() function to check 'dvbnet->exit'.
[mchehab: fix a checkpatch warning]
Link: https://lore.kernel.org/linux-media/20221117045925.14297-3-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae11c0efae ]
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/media/dvb-frontends/mn88443x.c:782:34: error: ‘mn88443x_of_match’ defined but not used [-Werror=unused-const-variable=]
Link: https://lore.kernel.org/linux-media/20230312131318.351173-28-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517a281338 ]
Since dvb_frontend_detach() is not called in ttusb_dec_exit_dvb(),
which is called when the device is disconnected, dvb_frontend_free()
is not finally called.
This causes a memory leak just by repeatedly plugging and
unplugging the device.
Fix this issue by adding dvb_frontend_detach() to ttusb_dec_exit_dvb().
Link: https://lore.kernel.org/linux-media/20221117045925.14297-5-imv4bel@gmail.com
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4315e5be7 ]
The function of "dvb_ca_en50221_write_data" at source/drivers/media
/dvb-core/dvb_ca_en50221.c is used for two cases.
The first case is for writing APDU data in the function of
"dvb_ca_en50221_io_write" at source/drivers/media/dvb-core/
dvb_ca_en50221.c.
The second case is for writing the host link buf size on the
Command Register in the function of "dvb_ca_en50221_link_init"
at source/drivers/media/dvb-core/dvb_ca_en50221.c.
In the second case, there exists a bug like following.
In the function of the "dvb_ca_en50221_link_init",
after a TV host calculates the host link buf_size,
the TV host writes the calculated host link buf_size on the
Size Register.
Accroding to the en50221 Spec (the page 60 of
https://dvb.org/wp-content/uploads/2020/02/En50221.V1.pdf),
before this writing operation, the "SW(CMDREG_SW)" flag in the
Command Register should be set. We can see this setting operation
in the function of the "dvb_ca_en50221_link_init" like below.
...
if ((ret = ca->pub->write_cam_control(ca->pub, slot,
CTRLIF_COMMAND, IRQEN | CMDREG_SW)) != 0)
return ret;
...
But, after that, the real writing operation is implemented using
the function of the "dvb_ca_en50221_write_data" in the function of
"dvb_ca_en50221_link_init", and the "dvb_ca_en50221_write_data"
includes the function of "ca->pub->write_cam_control",
and the function of the "ca->pub->write_cam_control" in the
function of the "dvb_ca_en50221_wrte_data" does not include
"CMDREG_SW" flag like below.
...
if ((status = ca->pub->write_cam_control(ca->pub, slot,
CTRLIF_COMMAND, IRQEN | CMDREG_HC)) != 0)
...
In the above source code, we can see only the "IRQEN | CMDREG_HC",
but we cannot see the "CMDREG_SW".
The "CMDREG_SW" flag which was set in the function of the
"dvb_ca_en50221_link_init" was rollbacked by the follwoing function
of the "dvb_ca_en50221_write_data".
This is a bug. and this bug causes that the calculated host link buf_size
is not properly written in the CI module.
Through this patch, we fix this bug.
Link: https://lore.kernel.org/linux-media/20220818125027.1131-1-yongsuyoo0215@gmail.com
Signed-off-by: YongSu Yoo <yongsuyoo0215@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ded5bd2a4 ]
In digitv_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach digitv_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd76 ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
Link: https://lore.kernel.org/linux-media/20230313095008.1039689-1-harperchen1110@gmail.com
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa4a447b81 ]
In rtl28xxu_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach rtl28xxu_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd76
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
Link: https://lore.kernel.org/linux-media/tencent_3623572106754AC2F266B316798B0F6CCA05@qq.com
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff9190901 ]
In ce6230_i2c_master_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach ce6230_i2c_master_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd76 ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
Link: https://lore.kernel.org/linux-media/20230313092751.209496-1-harperchen1110@gmail.com
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7efb10d8dc ]
In dvb_demux.c, some logics exist which compare the expected
continuity counter and the real continuity counter. If they
are not matched each other, both of the expected continuity
counter and the real continuity counter should be printed.
But there exists a bug that the expected continuity counter
is not correctly printed. The expected continuity counter is
replaced with the real countinuity counter + 1 so that
the epected continuity counter is not correclty printed.
This is wrong. This bug is fixed.
Link: https://lore.kernel.org/linux-media/20230305212519.499-1-yongsuyoo0215@gmail.com
Signed-off-by: YongSu Yoo <yongsuyoo0215@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f63550e2b1 ]
Apply a workaround for what appears to be a hardware quirk.
The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.
This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).
Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
i2cset -y 0 0x1a $(($1*2)) $2
}
For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x87 # out, dac
ssmset 0x06 0x07 # chip
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
(enable MCLK)
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x06 0x1f # chip
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
ssmset 0x06 0x07 # dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
ssmset 0x06 0x07 # out
NOT OK
For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
(enable MCLK after reset)
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
NOT OK
ssmset 0x06 0x07 # chip, out, dac
NOT OK
Signed-off-by: Paweł Anikiel <pan@semihalf.com
Link: https://lore.kernel.org/r/20230508113037.137627-8-pan@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8680407b6f ]
This change ensures that if configured in the policy, the if_id set in
the policy and secpath states match during the inbound policy check.
Without this, there is potential for ambiguity where entries in the
secpath differing by only the if_id could be mismatched.
Notably, this is checked in the outbound direction when resolving
templates to SAs, but not on the inbound path when matching SAs and
policies.
Test: Tested against Android kernel unit tests & CTS
Signed-off-by: Benedict Wong <benedictwong@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73a23d7710 ]
Since we no longer (want to) export any libc symbols the
_user portions of any drivers need to be built into image
rather than the module. I missed this for the watchdog.
Fix the watchdog accordingly.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd375feeaf ]
On Kingston KC3000 and Kingston FURY Renegade (both have the same PCI
IDs) accessing temp3_{min,max} fails with an invalid field error (note
that there is no problem setting the thresholds for temp1).
This contradicts the NVM Express Base Specification 2.0b, page 292:
The over temperature threshold and under temperature threshold
features shall be implemented for all implemented temperature sensors
(i.e., all Temperature Sensor fields that report a non-zero value).
Define NVME_QUIRK_NO_SECONDARY_TEMP_THRESH that disables the thresholds
for all but the composite temperature and set it for this device.
Signed-off-by: Hristo Venev <hristo@venev.name>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bdf1ad8d1 ]
Minor fix to reset the info field to NULL in case of error.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c75f5a5506 ]
A use-after-free bug may occur if init_imstt invokes framebuffer_release
and free the info ptr. The caller, imsttfb_probe didn't notice that and
still keep the ptr as private data in pdev.
If we remove the driver which will call imsttfb_remove to make cleanup,
UAF happens.
Fix it by return error code if bad case happens in init_imstt.
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 504a10d9e4 ]
On corrupt gfs2 file systems the evict code can try to reference the
journal descriptor structure, jdesc, after it has been freed and set to
NULL. The sequence of events is:
init_journal()
...
fail_jindex:
gfs2_jindex_free(sdp); <------frees journals, sets jdesc = NULL
if (gfs2_holder_initialized(&ji_gh))
gfs2_glock_dq_uninit(&ji_gh);
fail:
iput(sdp->sd_jindex); <--references jdesc in evict_linked_inode
evict()
gfs2_evict_inode()
evict_linked_inode()
ret = gfs2_trans_begin(sdp, 0, sdp->sd_jdesc->jd_blocks);
<------references the now freed/zeroed sd_jdesc pointer.
The call to gfs2_trans_begin is done because the truncate_inode_pages
call can cause gfs2 events that require a transaction, such as removing
journaled data (jdata) blocks from the journal.
This patch fixes the problem by adding a check for sdp->sd_jdesc to
function gfs2_evict_inode. In theory, this should only happen to corrupt
gfs2 file systems, when gfs2 detects the problem, reports it, then tries
to evict all the system inodes it has read in up to that point.
Reported-by: Yang Lan <lanyang0908@gmail.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e10707d586 ]
When adding proper support for V4L2_FIELD_ALTERNATE it was missed that
this field format should trigger an interrupt for each field, not just
for the whole frame. Fix this by marking it as progressive in the
capture setup, which will then select the correct interrupt mode.
Tested on both Gen2 and Gen3 with the result of a doubling of the frame
rate for V4L2_FIELD_ALTERNATE. From a PAL video source the frame rate is
now 50, which is expected for alternate field capture.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa3eeb638d ]
When unwind instruction is 0xb2,the subsequent instructions
are uleb128 bytes.
For now,it uses only the first uleb128 byte in code.
For vsp increments of 0x204~0x400,use one uleb128 byte like below:
0xc06a00e4 <unwind_test_work>: 0x80b27fac
Compact model index: 0
0xb2 0x7f vsp = vsp + 1024
0xac pop {r4, r5, r6, r7, r8, r14}
For vsp increments larger than 0x400,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x01 vsp = vsp + 1032
0xac pop {r4, r5, r6, r7, r8, r14}
The unwind works well since the decoded uleb128 byte is also 0x81.
For vsp increments larger than 0x600,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x02 vsp = vsp + 1544
0xac pop {r4, r5, r6, r7, r8, r14}
In this case,the decoded uleb128 result is 0x101(vsp=0x204+(0x101<<2)).
While the uleb128 used in code is 0x81(vsp=0x204+(0x81<<2)).
The unwind aborts at this frame since it gets incorrect vsp.
To fix this,add uleb128 decode to cover all the above case.
Signed-off-by: Haibo Li <haibo.li@mediatek.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ae5afd02a ]
If the sibling keys check fails before we move keys from one sibling
leaf to another, we are not aborting the transaction - we leave that to
some higher level caller of btrfs_search_slot() (or anything else that
uses it to insert items into a b+tree).
This means that the transaction abort will provide a stack trace that
omits the b+tree modification call chain. So change this to immediately
abort the transaction and therefore get a more useful stack trace that
shows us the call chain in the bt+tree modification code.
It's also important to immediately abort the transaction just in case
some higher level caller is not doing it, as this indicates a very
serious corruption and we should stop the possibility of doing further
damage.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d1e952a2b ]
If a user can make copy_from_user() fail, there is a potential for
UAF/DF due to a lack of locking around the allocation, use and freeing
of the data buffers.
This issue is not theoretical. I managed to author a POC for it:
BUG: KASAN: double-free in kfree+0x5c/0xac
Free of addr ffff29280be5de00 by task poc/356
CPU: 1 PID: 356 Comm: poc Not tainted 6.1.0-00001-g961aa6552c04-dirty #20
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x64/0x80
print_report+0x188/0x48c
kasan_report_invalid_free+0xa0/0xc0
____kasan_slab_free+0x174/0x1b0
__kasan_slab_free+0x18/0x24
__kmem_cache_free+0x130/0x2e0
kfree+0x5c/0xac
mbox_test_message_write+0x208/0x29c
full_proxy_write+0x90/0xf0
vfs_write+0x154/0x440
ksys_write+0xcc/0x180
__arm64_sys_write+0x44/0x60
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x40/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xf4/0x120
el0t_64_sync+0x18c/0x190
Allocated by task 356:
kasan_save_stack+0x3c/0x70
kasan_set_track+0x2c/0x40
kasan_save_alloc_info+0x24/0x34
__kasan_kmalloc+0xb8/0xc0
kmalloc_trace+0x58/0x70
mbox_test_message_write+0x6c/0x29c
full_proxy_write+0x90/0xf0
vfs_write+0x154/0x440
ksys_write+0xcc/0x180
__arm64_sys_write+0x44/0x60
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x40/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xf4/0x120
el0t_64_sync+0x18c/0x190
Freed by task 357:
kasan_save_stack+0x3c/0x70
kasan_set_track+0x2c/0x40
kasan_save_free_info+0x38/0x5c
____kasan_slab_free+0x13c/0x1b0
__kasan_slab_free+0x18/0x24
__kmem_cache_free+0x130/0x2e0
kfree+0x5c/0xac
mbox_test_message_write+0x208/0x29c
full_proxy_write+0x90/0xf0
vfs_write+0x154/0x440
ksys_write+0xcc/0x180
__arm64_sys_write+0x44/0x60
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x40/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xf4/0x120
el0t_64_sync+0x18c/0x190
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c51e431052 ]
Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for
Glenfly Gpus.
- In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware
limitation, need to increase hdac interrupt interval.
- In azx_first_init, enable polling mode for Glenfly Gpu. When the codec
complete the command, it sends interrupt and writes response entries to
memory, howerver, the write requests sometimes are not actually
synchronized to memory when driver handle hdac interrupt on Glenfly Gpus.
If the RIRB status is not updated in the interrupt handler,
azx_rirb_get_response keeps trying to recevie a response from rirb until
1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue.
- In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need
driver to do actual clean-ups for the linked codec when switch from one
codec to another.
Signed-off-by: jasontao <jasontao@glenfly.com>
Signed-off-by: Reaper Li <reaperlioc@glenfly.com>
Link: https://lore.kernel.org/r/20230426013059.4329-1-reaperlioc@glenfly.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b22656ca ]
Doing a 'cat /dev/watchdog0' with menz069_wdt as watchdog0 will result in
a NULL pointer dereference.
This happens because we're passing the wrong pointer to
watchdog_register_device(). Fix this by getting rid of the static
watchdog_device structure and use the one embedded into the driver's
per-instance private data.
Signed-off-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230418172531.177349-2-jth@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38eecbe086 ]
[WHY]
Function "amdgpu_irq_update()" called by "amdgpu_device_ip_late_init()" is an atomic context.
We shouldn't access registers through KIQ since "msleep()" may be called in "amdgpu_kiq_rreg()".
[HOW]
Move function "amdgpu_virt_release_full_gpu()" after function "amdgpu_device_ip_late_init()",
to ensure that registers be accessed through RLCG instead of KIQ.
Call Trace:
<TASK>
show_stack+0x52/0x69
dump_stack_lvl+0x49/0x6d
dump_stack+0x10/0x18
__schedule_bug.cold+0x4f/0x6b
__schedule+0x473/0x5d0
? __wake_up_klogd.part.0+0x40/0x70
? vprintk_emit+0xbe/0x1f0
schedule+0x68/0x110
schedule_timeout+0x87/0x160
? timer_migration_handler+0xa0/0xa0
msleep+0x2d/0x50
amdgpu_kiq_rreg+0x18d/0x1f0 [amdgpu]
amdgpu_device_rreg.part.0+0x59/0xd0 [amdgpu]
amdgpu_device_rreg+0x3a/0x50 [amdgpu]
amdgpu_sriov_rreg+0x3c/0xb0 [amdgpu]
gfx_v10_0_set_gfx_eop_interrupt_state.constprop.0+0x16c/0x190 [amdgpu]
gfx_v10_0_set_eop_interrupt_state+0xa5/0xb0 [amdgpu]
amdgpu_irq_update+0x53/0x80 [amdgpu]
amdgpu_irq_get+0x7c/0xb0 [amdgpu]
amdgpu_fence_driver_hw_init+0x58/0x90 [amdgpu]
amdgpu_device_init.cold+0x16b7/0x2022 [amdgpu]
Signed-off-by: Chong Li <chongli2@amd.com>
Reviewed-by: JingWen.Chen2@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
