[ Upstream commit 0b8e7bbde5 ]
The datasheet of V3s (and various other chips) wrote
that TCON0_DCLK_DIV can be >= 1 if only dclk is used,
and must >= 6 if dclk1 or dclk2 is used. As currently
neither dclk1 nor dclk2 is used (no writes to these
bits), let's set minimal division to 1.
If this minimal division is 6, some common dot clock
frequencies can't be produced (e.g. 30MHz will not be
possible and will fallback to 25MHz), which is
obviously not an expected behaviour.
Signed-off-by: Yunhao Tian <t123yh@outlook.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/linux-arm-kernel/MN2PR08MB57905AD8A00C08DA219377C989760@MN2PR08MB5790.namprd08.prod.outlook.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79aae6acbe ]
The device md->input is used after it is released. Setting the device
data to NULL is unnecessary as the device is never used again. Instead,
md->input should be assigned NULL to avoid accessing the freed memory
accidently. Besides, checking md->si against NULL is superfluous as it
points to a variable address, which cannot be NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1572936379-6423-1-git-send-email-bianpan2016@163.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4944a4b107 ]
An ESP packet could be decrypted in async mode if the input handler for
this packet returns -EINPROGRESS in xfrm_input(). At this moment the device
reference in skb is held. Later xfrm_input() will be invoked again to
resume the processing.
If the transform state is still valid it would continue to release the
device reference and there won't be a problem; however if the transform
state is not valid when async resumption happens, the packet will be
dropped while the device reference is still being held.
When the device is deleted for some reason and the reference to this
device is not properly released, the kernel will keep logging like:
unregister_netdevice: waiting for ppp2 to become free. Usage count = 1
The issue is observed when running IPsec traffic over a PPPoE device based
on a bridge interface. By terminating the PPPoE connection on the server
end for multiple times, the PPPoE device on the client side will eventually
get stuck on the above warning message.
This patch will check the async mode first and continue to release device
reference in async resumption, before it is dropped due to invalid state.
v2: Do not assign address family from outer_mode in the transform if the
state is invalid
v3: Release device reference in the error path instead of jumping to resume
Fixes: 4ce3dbe397 ("xfrm: Fix xfrm_input() to verify state is valid when (encap_type < 0)")
Signed-off-by: Xiaodong Xu <stid.smth@gmail.com>
Reported-by: Bo Chen <chenborfc@163.com>
Tested-by: Bo Chen <chenborfc@163.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a71a29f50d ]
I2C communication errors (-EREMOTEIO) during the IRQ handler of nxp-nci
result in a NULL pointer dereference at the moment:
BUG: kernel NULL pointer dereference, address: 0000000000000000
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 355 Comm: irq/137-nxp-nci Not tainted 5.4.0-rc6 #1
RIP: 0010:skb_queue_tail+0x25/0x50
Call Trace:
nci_recv_frame+0x36/0x90 [nci]
nxp_nci_i2c_irq_thread_fn+0xd1/0x285 [nxp_nci_i2c]
? preempt_count_add+0x68/0xa0
? irq_forced_thread_fn+0x80/0x80
irq_thread_fn+0x20/0x60
irq_thread+0xee/0x180
? wake_threads_waitq+0x30/0x30
kthread+0xfb/0x130
? irq_thread_check_affinity+0xd0/0xd0
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x40
Afterward the kernel must be rebooted to work properly again.
This happens because it attempts to call nci_recv_frame() with skb == NULL.
However, unlike nxp_nci_fw_recv_frame(), nci_recv_frame() does not have any
NULL checks for skb, causing the NULL pointer dereference.
Change the code to call only nxp_nci_fw_recv_frame() in case of an error.
Make sure to log it so it is obvious that a communication error occurred.
The error above then becomes:
nxp-nci_i2c i2c-NXP1001:00: NFC: Read failed with error -121
nci: __nci_request: wait_for_completion_interruptible_timeout failed 0
nxp-nci_i2c i2c-NXP1001:00: NFC: Read failed with error -121
Fixes: 6be88670fc ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69924b8968 ]
if the child has been negative and just went positive
under us, we want coherent d_is_positive() and ->d_inode.
Don't unlock the parent until we'd done that work...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb1a4badf5 ]
From gen2 PN is totally offloaded to hardware (also the space for the
IV isn't part of the skb). As you can see in mvm/mac80211.c:3545, the
MAC for cipher types CCMP/GCMP doesn't set
IEEE80211_KEY_FLAG_PUT_IV_SPACE for gen2 NICs.
This causes all the AMSDU data to be corrupted with cipher enabled.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03ad0d703d ]
if the second call of should_expire() in there ends up
grabbing and returning a new reference to dentry, we need
to drop it before continuing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f6a1964771 upstream.
PL011's ->flush_buffer() implementation releases and reacquires the port
lock. Due to a race condition here, data can end up being added to the
circular buffer but neither being discarded nor being sent out. This
leads to, for example, tcdrain(2) waiting indefinitely.
Process A Process B
uart_flush_buffer()
- acquire lock
- circ_clear
- pl011_flush_buffer()
-- release lock
-- dmaengine_terminate_all()
uart_write()
- acquire lock
- add chars to circ buffer
- start_tx()
-- start DMA
- release lock
-- acquire lock
-- turn off DMA
-- release lock
// Data in circ buffer but DMA is off
According to the comment in the code, the releasing of the lock around
dmaengine_terminate_all() is to avoid a deadlock with the DMA engine
callback. However, since the time this code was written, the DMA engine
API documentation seems to have been clarified to say that
dmaengine_terminate_all() (in the identically implemented but
differently named dmaengine_terminate_async() variant) does not wait for
any running complete callback to be completed and can even be called
from a complete callback. So there is no possibility of deadlock if the
DMA engine driver implements this API correctly.
So we should be able to just remove this release and reacquire of the
lock to prevent the aforementioned race condition.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191118092547.32135-1-vincent.whitchurch@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b027ce2583 upstream.
hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and
Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca
disables flow, configures the uart baudrate, and then reenables flow - at
which point an event is expected to be received over the uart from the
wcn3990. It is observed that this event comes after the baudrate change
but before hci_qca re-enables flow. This is unexpected, and is a result of
msm_reset() being broken.
According to the uart_dm hardware documentation, it is recommended that
automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto
hw flow control will manage RFR based on the configured watermark. When
there is space to receive data, the hw will assert RFR. When the watermark
is hit, the hw will de-assert RFR.
The hardware documentation indicates that RFR can me manually managed via
CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR
de-asserts RFR.
msm_reset() is broken because after resetting the hardware, it
unconditionally asserts RFR via SET_RFR. This enables flow regardless of
the current configuration, and would undo a previous flow disable
operation. It should instead de-assert RFR via RESET_RFR to block flow
until the hardware is reconfigured. msm_serial should rely on the client
to specify that flow should be enabled, either via mctrl() or the termios
structure, and only assert RFR in response to those triggers.
Fixes: 04896a77a9 ("msm_serial: serial driver for MSM7K onboard serial peripheral.")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Gross <agross@kernel.org>
Link: https://lore.kernel.org/r/20191021154616.25457-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45a2d64696 upstream.
The layout of struct timeval is different on sparc64 from
anything else, and the patch I did long ago failed to take
this into account.
Change it now to handle sparc64 user space correctly again.
Quite likely nobody cares about parallel ports on sparc64,
but there is no reason not to fix it.
Cc: stable@vger.kernel.org
Fixes: 9a45048408 ("lp: support 64-bit time_t user space")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191108203435.112759-7-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e5e929c00 upstream.
Commit 3499359418 ("arm64: tegra: Enable HDMI on Jetson TX1")
added a regulator for HDMI on the Jetson TX1 platform. This regulator
has an active high enable, but the GPIO specifier for enabling the
regulator incorrectly defines it as active-low. This causes the
following warning to occur on boot ...
WARNING KERN regulator@10 GPIO handle specifies active low - ignored
The fixed-regulator binding does not use the active-low flag from the
gpio specifier and purely relies of the presence of the
'enable-active-high' property to determine if it is active high or low
(if this property is omitted). Fix this warning by setting the GPIO
to active-high in the GPIO specifier which aligns with the presense of
the 'enable-active-high' property.
Fixes: 3499359418 ("arm64: tegra: Enable HDMI on Jetson TX1")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a31eda65ba upstream.
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3edd ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3e4f3fc8e upstream.
The AML code implementing the WMI methods creates a variable length
field to hold the input data we pass like this:
CreateDWordField (Arg1, 0x0C, DSZI)
Local5 = DSZI /* \HWMC.DSZI */
CreateField (Arg1, 0x80, (Local5 * 0x08), DAIN)
If we pass 0 as bios_args.datasize argument then (Local5 * 0x08)
is 0 which results in these errors:
[ 71.973305] ACPI BIOS Error (bug): Attempt to CreateField of length zero (20190816/dsopcode-133)
[ 71.973332] ACPI Error: Aborting method \HWMC due to previous error (AE_AML_OPERAND_VALUE) (20190816/psparse-529)
[ 71.973413] ACPI Error: Aborting method \_SB.WMID.WMAA due to previous error (AE_AML_OPERAND_VALUE) (20190816/psparse-529)
And in our HPWMI_WIRELESS2_QUERY calls always failing. for read commands
like HPWMI_WIRELESS2_QUERY the DSZI value is not used / checked, except for
read commands where extra input is needed to specify exactly what to read.
So for HPWMI_WIRELESS2_QUERY we can safely pass the size of the expected
output as insize to hp_wmi_perform_query(), as we are already doing for all
other HPWMI_READ commands we send. Doing so fixes these errors.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=197007
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201981
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16245db148 upstream.
The HP WMI calls may take up to 128 bytes of data as input, and
the AML methods implementing the WMI calls, declare a couple of fields for
accessing input in different sizes, specifycally the HWMC method contains:
CreateField (Arg1, 0x80, 0x0400, D128)
Even though we do not use any of the WMI command-types which need a buffer
of this size, the APCI interpreter still tries to create it as it is
declared in generoc code at the top of the HWMC method which runs before
the code looks at which command-type is requested.
This results in many of these errors on many different HP laptop models:
[ 14.459261] ACPI Error: Field [D128] at 1152 exceeds Buffer [NULL] size 160 (bits) (20170303/dsopcode-236)
[ 14.459268] ACPI Error: Method parse/execution failed [\HWMC] (Node ffff8edcc61507f8), AE_AML_BUFFER_LIMIT (20170303/psparse-543)
[ 14.459279] ACPI Error: Method parse/execution failed [\_SB.WMID.WMAA] (Node ffff8edcc61523c0), AE_AML_BUFFER_LIMIT (20170303/psparse-543)
This commit increases the size of the data element of the bios_args struct
to 128 bytes fixing these errors.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=197007
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201981
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc832dc8e3 upstream.
When a period length is not multiple of FIFO some data may be stuck
within FIFO.
Burst/FIFO Threshold/Period or buffer length check has to be hardened
In any case DMA will grant any request from client but will degraded
any parameters whether awkward.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba3c5215d upstream.
Because of regmap cache, interrupts may not be cleared
as expected.
Declare IFCR register as write only and make writings
to IFCR register unconditional.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72cfd1ad10 upstream.
STM32MP1 clock IP offers lots of Kernel clocks that are shared
by multiple IP's at the same time.
Then boot loader applies a clock tree that allows to use all IP's
at same time and with the maximum of performance.
Not change parents on a change rate on kernel clocks ensures
the integrity of the system.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab41b99e7e upstream.
Start streaming was sometimes failing because of pm_runtime_get_sync()
non-0 return value. In fact return value was not an error but a
positive value (1), indicating that PM was already enabled.
Fix this by going to error path only with negative return value.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cb0d2aee2 upstream.
Upstream commit 58e7515500 ("HID: core: move Usage Page concatenation
to Main item") adds support for Usage Page item after Usage ID items
(such as keyboards manufactured by Primax).
Usage Page concatenation in Main item works well for following report
descriptor patterns:
USAGE_PAGE (Keyboard) 05 07
USAGE_MINIMUM (Keyboard LeftControl) 19 E0
USAGE_MAXIMUM (Keyboard Right GUI) 29 E7
LOGICAL_MINIMUM (0) 15 00
LOGICAL_MAXIMUM (1) 25 01
REPORT_SIZE (1) 75 01
REPORT_COUNT (8) 95 08
INPUT (Data,Var,Abs) 81 02
-------------
USAGE_MINIMUM (Keyboard LeftControl) 19 E0
USAGE_MAXIMUM (Keyboard Right GUI) 29 E7
LOGICAL_MINIMUM (0) 15 00
LOGICAL_MAXIMUM (1) 25 01
REPORT_SIZE (1) 75 01
REPORT_COUNT (8) 95 08
USAGE_PAGE (Keyboard) 05 07
INPUT (Data,Var,Abs) 81 02
But it makes the parser act wrong for the following report
descriptor pattern(such as some Gamepads):
USAGE_PAGE (Button) 05 09
USAGE (Button 1) 09 01
USAGE (Button 2) 09 02
USAGE (Button 4) 09 04
USAGE (Button 5) 09 05
USAGE (Button 7) 09 07
USAGE (Button 8) 09 08
USAGE (Button 14) 09 0E
USAGE (Button 15) 09 0F
USAGE (Button 13) 09 0D
USAGE_PAGE (Consumer Devices) 05 0C
USAGE (Back) 0a 24 02
USAGE (HomePage) 0a 23 02
LOGICAL_MINIMUM (0) 15 00
LOGICAL_MAXIMUM (1) 25 01
REPORT_SIZE (1) 75 01
REPORT_COUNT (11) 95 0B
INPUT (Data,Var,Abs) 81 02
With Usage Page concatenation in Main item, parser recognizes all the
11 Usages as consumer keys, it is not the HID device's real intention.
This patch checks whether Usage Page is really defined after Usage ID
items by comparing usage page using status.
Usage Page concatenation on currently defined Usage Page will always
do in local parsing when Usage ID items encountered.
When Main item is parsing, concatenation will do again with last
defined Usage Page if this page has not been used in the previous
usages concatenation.
Signed-off-by: Candle Sun <candle.sun@unisoc.com>
Signed-off-by: Nianfu Bai <nianfu.bai@unisoc.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Siarhei Vishniakou <svv@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88f8598d0a upstream.
Previously TCP only warns if its RTO timer fires and the
retransmission queue is empty, but it'll cause null pointer
reference later on. It's better to avoid such catastrophic failure
and simply exit with a warning.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dba9a3dfe9 upstream.
Add spinlock protection on IPCC register update to avoid race condition.
Without this fix, stm32_ipcc_set_bits and stm32_ipcc_clr_bits can be
called in parallel for different channels. This results in register
corruptions.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84a1c2109d upstream.
The "params->size" is defined as "u64".
And "info->sector_size" and "info->n_sectors" are defined as
unsigned int and u16.
Thus, u64 data might have strange data(loss data) if the result
overflows an unsigned int.
This patch casts "info->sector_size" to an u64.
Signed-off-by: huijin.park <huijin.park@samsung.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a62520473f upstream.
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
