[ Upstream commit 7314f5480f ]
nr_find_socket(), nr_find_peer() and nr_find_listener() lock the
sock after finding it in the global list. However, the call path
requires BH disabled for the sock lock consistently.
Actually the locking is unnecessary at this point, we can just hold
the sock refcnt to make sure it is not gone after we unlock the global
list, and lock it later only when needed.
Reported-and-tested-by: syzbot+f621cda8b7e598908efa@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8742beb50f ]
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff5 ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ade446403b ]
Since commit 7969e5c40d ("ip: discard IPv4 datagrams with overlapping
segments.") IPv4 reassembly code drops the whole queue whenever an
overlapping fragment is received. However, the test is written in a way
which detects duplicate fragments as overlapping so that in environments
with many duplicate packets, fragmented packets may be undeliverable.
Add an extra test and for (potentially) duplicate fragment, only drop the
new fragment rather than the whole queue. Only starting offset and length
are checked, not the contents of the fragments as that would be too
expensive. For similar reason, linear list ("run") of a rbtree node is not
iterated, we only check if the new fragment is a subset of the interval
covered by existing consecutive fragments.
v2: instead of an exact check iterating through linear list of an rbtree
node, only check if the new fragment is subset of the "run" (suggested
by Eric Dumazet)
Fixes: 7969e5c40d ("ip: discard IPv4 datagrams with overlapping segments.")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb24274546 ]
syzbot reported the use of uninitialized udp6_addr::sin6_scope_id.
We can just set ::sin6_scope_id to zero, as tunnels are unlikely
to use an IPv6 address that needs a scope id and there is no
interface to bind in this context.
For net-next, it looks different as we have cfg->bind_ifindex there
so we can probably call ipv6_iface_scope_id().
Same for ::sin6_flowinfo, tunnels don't use it.
Fixes: 8024e02879 ("udp: Add udp_sock_create for UDP tunnels to open listener socket")
Reported-by: syzbot+c56449ed3652e6720f30@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40c3ff6d5e ]
Packet sockets may call dev_header_parse with NULL daddr. Make
lowpan_header_ops.create fail.
Fixes: 87a93e4ece ("ieee802154: change needed headroom/tailroom")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 756af9c642 ]
Commit 33a48ab105 ("ibmveth: Fix DMA unmap error") fixed an issue in the
normal code path of ibmveth_xmit_start() that was originally introduced by
Commit 6e8ab30ec6 ("ibmveth: Add scatter-gather support"). This original
fix missed the error path where dma_unmap_page is wrongly called on the
header portion in descs[0] which was mapped with dma_map_single. As a
result a failure to DMA map any of the frags results in a dmesg warning
when CONFIG_DMA_API_DEBUG is enabled.
------------[ cut here ]------------
DMA-API: ibmveth 30000002: device driver frees DMA memory with wrong function
[device address=0x000000000a430000] [size=172 bytes] [mapped as page] [unmapped as single]
WARNING: CPU: 1 PID: 8426 at kernel/dma/debug.c:1085 check_unmap+0x4fc/0xe10
...
<snip>
...
DMA-API: Mapped at:
ibmveth_start_xmit+0x30c/0xb60
dev_hard_start_xmit+0x100/0x450
sch_direct_xmit+0x224/0x490
__qdisc_run+0x20c/0x980
__dev_queue_xmit+0x1bc/0xf20
This fixes the API misuse by unampping descs[0] with dma_unmap_single.
Fixes: 6e8ab30ec6 ("ibmveth: Add scatter-gather support")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c433570458 ]
There are multiple issues here:
1. After freeing dev->ax25_ptr, we need to set it to NULL otherwise
we may use a dangling pointer.
2. There is a race between ax25_setsockopt() and device notifier as
reported by syzbot. Close it by holding RTNL lock.
3. We need to test if dev->ax25_ptr is NULL before using it.
Reported-and-tested-by: syzbot+ae6bb869cbed29b29040@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5648451e30 ]
vr.vifi is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/ipv4/ipmr.c:1616 ipmr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
net/ipv4/ipmr.c:1690 ipmr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
Fix this by sanitizing vr.vifi before using it to index mrt->vif_table'
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69d2c86766 ]
vr.mifi is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/ipv6/ip6mr.c:1845 ip6mr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
net/ipv6/ip6mr.c:1919 ip6mr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
Fix this by sanitizing vr.mifi before using it to index mrt->vif_table'
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eee74b7e2 upstream.
Directly including access_ok.h can result in the following compile errors
if an architecture such as ia64 does not support direct unaligned accesses.
include/linux/unaligned/access_ok.h:7:19: error:
redefinition of 'get_unaligned_le16'
include/linux/unaligned/le_struct.h:6:19: note:
previous definition of 'get_unaligned_le16' was here
include/linux/unaligned/access_ok.h:12:19: error:
redefinition of 'get_unaligned_le32'
include/linux/unaligned/le_struct.h:11:19: note:
previous definition of 'get_unaligned_le32' was here
Include asm/unaligned.h instead and let the architecture decide which
access functions to use.
Cc: Clément Perrochaud <clement.perrochaud@effinnov.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 505b524032 upstream.
nr is indirectly controlled by user-space, hence leading to a
potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/gpu/drm/drm_ioctl.c:805 drm_ioctl() warn: potential spectre issue 'dev->driver->ioctls' [r]
drivers/gpu/drm/drm_ioctl.c:810 drm_ioctl() warn: potential spectre issue 'drm_ioctls' [r] (local cap)
drivers/gpu/drm/drm_ioctl.c:892 drm_ioctl_flags() warn: potential spectre issue 'drm_ioctls' [r] (local cap)
Fix this by sanitizing nr before using it to index dev->driver->ioctls
and drm_ioctls.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220000015.GA18973@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea5751ccd6 upstream.
proc_sys_lookup can fail with ENOMEM instead of ENOENT when the
corresponding sysctl table is being unregistered. In our case we see
this upon opening /proc/sys/net/*/conf files while network interfaces
are being deleted, which confuses our configuration daemon.
The problem was successfully reproduced and this fix tested on v4.9.122
and v4.20-rc6.
v2: return ERR_PTRs in all cases when proc_sys_make_inode fails instead
of mixing them with NULL. Thanks Al Viro for the feedback.
Fixes: ace0c791e6 ("proc/sysctl: Don't grab i_lock under sysctl_lock.")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7c3f05e34 upstream.
From printk()/serial console point of view panic() is special, because
it may force CPU to re-enter printk() or/and serial console driver.
Therefore, some of serial consoles drivers are re-entrant. E.g. 8250:
serial8250_console_write()
{
if (port->sysrq)
locked = 0;
else if (oops_in_progress)
locked = spin_trylock_irqsave(&port->lock, flags);
else
spin_lock_irqsave(&port->lock, flags);
...
}
panic() does set oops_in_progress via bust_spinlocks(1), so in theory
we should be able to re-enter serial console driver from panic():
CPU0
<NMI>
uart_console_write()
serial8250_console_write() // if (oops_in_progress)
// spin_trylock_irqsave()
call_console_drivers()
console_unlock()
console_flush_on_panic()
bust_spinlocks(1) // oops_in_progress++
panic()
<NMI/>
spin_lock_irqsave(&port->lock, flags) // spin_lock_irqsave()
serial8250_console_write()
call_console_drivers()
console_unlock()
printk()
...
However, this does not happen and we deadlock in serial console on
port->lock spinlock. And the problem is that console_flush_on_panic()
called after bust_spinlocks(0):
void panic(const char *fmt, ...)
{
bust_spinlocks(1);
...
bust_spinlocks(0);
console_flush_on_panic();
...
}
bust_spinlocks(0) decrements oops_in_progress, so oops_in_progress
can go back to zero. Thus even re-entrant console drivers will simply
spin on port->lock spinlock. Given that port->lock may already be
locked either by a stopped CPU, or by the very same CPU we execute
panic() on (for instance, NMI panic() on printing CPU) the system
deadlocks and does not reboot.
Fix this by removing bust_spinlocks(0), so oops_in_progress is always
set in panic() now and, thus, re-entrant console drivers will trylock
the port->lock instead of spinning on it forever, when we call them
from console_flush_on_panic().
Link: http://lkml.kernel.org/r/20181025101036.6823-1-sergey.senozhatsky@gmail.com
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Daniel Wang <wonderfly@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Feiner <pfeiner@google.com>
Cc: linux-serial@vger.kernel.org
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e58725d51f upstream.
UBIFS's recovery code strictly assumes that a deleted inode will never
come back, therefore it removes all data which belongs to that inode
as soon it faces an inode with link count 0 in the replay list.
Before O_TMPFILE this assumption was perfectly fine. With O_TMPFILE
it can lead to data loss upon a power-cut.
Consider a journal with entries like:
0: inode X (nlink = 0) /* O_TMPFILE was created */
1: data for inode X /* Someone writes to the temp file */
2: inode X (nlink = 0) /* inode was changed, xattr, chmod, … */
3: inode X (nlink = 1) /* inode was re-linked via linkat() */
Upon replay of entry #2 UBIFS will drop all data that belongs to inode X,
this will lead to an empty file after mounting.
As solution for this problem, scan the replay list for a re-link entry
before dropping data.
Fixes: 474b93704f ("ubifs: Implement O_TMPFILE")
Cc: stable@vger.kernel.org # 4.9-4.18
Cc: Russell Senior <russell@personaltelco.net>
Cc: Rafał Miłecki <zajec5@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Richard Weinberger <richard@nod.at>
[rmilecki: update ubifs_assert() calls to compile with 4.18 and older]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e58725d51f)
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 68239654ac upstream.
The sequence
fpu->initialized = 1; /* step A */
preempt_disable(); /* step B */
fpu__restore(fpu);
preempt_enable();
in __fpu__restore_sig() is racy in regard to a context switch.
For 32bit frames, __fpu__restore_sig() prepares the FPU state within
fpu->state. To ensure that a context switch (switch_fpu_prepare() in
particular) does not modify fpu->state it uses fpu__drop() which sets
fpu->initialized to 0.
After fpu->initialized is cleared, the CPU's FPU state is not saved
to fpu->state during a context switch. The new state is loaded via
fpu__restore(). It gets loaded into fpu->state from userland and
ensured it is sane. fpu->initialized is then set to 1 in order to avoid
fpu__initialize() doing anything (overwrite the new state) which is part
of fpu__restore().
A context switch between step A and B above would save CPU's current FPU
registers to fpu->state and overwrite the newly prepared state. This
looks like a tiny race window but the Kernel Test Robot reported this
back in 2016 while we had lazy FPU support. Borislav Petkov made the
link between that report and another patch that has been posted. Since
the removal of the lazy FPU support, this race goes unnoticed because
the warning has been removed.
Disable bottom halves around the restore sequence to avoid the race. BH
need to be disabled because BH is allowed to run (even with preemption
disabled) and might invoke kernel_fpu_begin() by doing IPsec.
[ bp: massage commit message a bit. ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: stable@vger.kernel.org
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20181120102635.ddv3fvavxajjlfqk@linutronix.de
Link: https://lkml.kernel.org/r/20160226074940.GA28911@pd.tnic
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abf221d2f5 upstream.
spi_read() and spi_write() require DMA-safe memory. When
CONFIG_VMAP_STACK is selected, those functions cannot be used
with buffers on stack.
This patch replaces calls to spi_read() and spi_write() by
spi_write_then_read() which doesn't require DMA-safe buffers.
Fixes: 0c36ec3147 ("gpio: gpio driver for max7301 SPI GPIO expander")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b47979068 upstream.
While booting with rootfs on MMC, the following warning is encountered
on OMAP4430:
omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536]
This is because the DMA engine has a default maximum segment size of 64K
but HSMMC sets:
mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
which ends up telling the block layer that we support a maximum segment
size of 65535*512, which exceeds the advertised DMA engine capabilities.
Fix this by clamping the maximum segment size to the lower of the
maximum request size and of the DMA engine device used for either DMA
channel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3ae3401aa upstream.
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba9f39a785 upstream.
In commit 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0741ba40a upstream.
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45f750c16c upstream.
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5146f95df7 upstream.
The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.
Add a length check for both locations and updated hso_probe to bail on
error.
This issue has been assigned CVE-2018-19985.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b88aef36b8 ]
If __blkdev_issue_discard is in progress and a device mapper device is
reloaded with a table that doesn't support discard,
q->limits.max_discard_sectors is set to zero. This results in infinite
loop in __blkdev_issue_discard.
This patch checks if max_discard_sectors is zero and aborts with
-EOPNOTSUPP.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Zdenek Kabelac <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af097f5d19 ]
Don't build discards bigger than what the user asked for, if the
user decided to limit the size by writing to 'discard_max_bytes'.
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd7f3a249d ]
In order to read correctly from asynchronously updated RTC registers,
it's necessary to read repeatedly until their values do not change from
read to read. It's also necessary to wait for three RTC clock ticks for
certain operations. There are no timeouts in this code and these
operations could possibly loop forever.
To avoid kernel hangs, put in timeouts.
The iMX7d can be configured to stop the SRTC on a tamper event, which
will lockup the kernel inside this driver as described above.
These hangs can happen when running under qemu, which doesn't emulate
the SNVS RTC, though currently the driver will refuse to load on qemu
due to a timeout in the driver probe method.
It could also happen if the SRTC block where somehow placed into reset
or the slow speed clock that drives the SRTC counter (but not the CPU)
were to stop.
The symptoms on a two core iMX7d are a work queue hang on
rtc_timer_do_work(), which eventually blocks a systemd fsnotify
operation that triggers a work queue flush, causing systemd to hang and
thus causing all services that should be started by systemd, like a
console getty, to fail to start or stop.
Also optimize the wait code to wait less. It only needs to wait for the
clock to advance three ticks, not to see it change three times.
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bb633b1a9 ]
The clear of the LPTA_EN flag should be synced before writing to the
alarm register. Omitting this synchronization creates a race when
trying to change existing alarm.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7dcdf9d4e ]
nvmet_rdma_release_rsp() may free the response before using it at error
flow.
Fixes: 8407879 ("nvmet-rdma: fix possible bogus dereference under heavy load")
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0544ee4b1a ]
Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.
This leads to the following error in dmesg:
[ 5.222731] cmi: probe of SMB0001:00 failed with error -5
This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c7f25cae5 ]
According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.
The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.
The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.
To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c38f57da42 ]
If a local process has closed a connected socket and hasn't received a
RST packet yet, then the socket remains in the table until a timeout
expires.
When a vhost_vsock instance is released with the timeout still pending,
the socket is never freed because vhost_vsock has already set the
SOCK_DONE flag.
Check if the close timer is pending and let it close the socket. This
prevents the race which can leak sockets.
Reported-by: Maximilian Riemensberger <riemensberger@cadami.net>
Cc: Graham Whaley <graham.whaley@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e785302da ]
Missing a dependency. Shouldn't show cifs posix extensions
in Kconfig if CONFIG_CIFS_ALLOW_INSECURE_DIALECTS (ie SMB1
protocol) is disabled.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecb239d96d ]
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d0358d0ba ]
Chris has discovered and reported that v7_dma_inv_range() may corrupt
memory if address range is not aligned to cache line size.
Since the whole cache-v7m.S was lifted form cache-v7.S the same
observation applies to v7m_dma_inv_range(). So the fix just mirrors
what has been done for v7 with a little specific of M-class.
Cc: Chris Cole <chris@sageembedded.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1208f6a82 ]
This patch addresses possible memory corruption when
v7_dma_inv_range(start_address, end_address) address parameters are not
aligned to whole cache lines. This function issues "invalidate" cache
management operations to all cache lines from start_address (inclusive)
to end_address (exclusive). When start_address and/or end_address are
not aligned, the start and/or end cache lines are first issued "clean &
invalidate" operation. The assumption is this is done to ensure that any
dirty data addresses outside the address range (but part of the first or
last cache lines) are cleaned/flushed so that data is not lost, which
could happen if just an invalidate is issued.
The problem is that these first/last partial cache lines are issued
"clean & invalidate" and then "invalidate". This second "invalidate" is
not required and worse can cause "lost" writes to addresses outside the
address range but part of the cache line. If another component writes to
its part of the cache line between the "clean & invalidate" and
"invalidate" operations, the write can get lost. This fix is to remove
the extra "invalidate" operation when unaligned addressed are used.
A kernel module is available that has a stress test to reproduce the
issue and a unit test of the updated v7_dma_inv_range(). It can be
downloaded from
http://ftp.sageembedded.com/outgoing/linux/cache-test-20181107.tgz.
v7_dma_inv_range() is call by dmac_[un]map_area(addr, len, direction)
when the direction is DMA_FROM_DEVICE. One can (I believe) successfully
argue that DMA from a device to main memory should use buffers aligned
to cache line size, because the "clean & invalidate" might overwrite
data that the device just wrote using DMA. But if a driver does use
unaligned buffers, at least this fix will prevent memory corruption
outside the buffer.
Signed-off-by: Chris Cole <chris@sageembedded.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3494801cd ]
Malicious user space may try to force the verifier to use as much cpu
time and memory as possible. Hence check for pending signals
while verifying the program.
Note that suspend of sys_bpf(PROG_LOAD) syscall will lead to EAGAIN,
since the kernel has to release the resources used for program verification.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b603f9e43 ]
MLX4_EN depends on NETDEVICES, ETHERNET and INET Kconfigs.
Make sure they are listed in MLX4_EN Kconfig dependencies.
This fixes the following build break:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: ‘struct iphdr’ declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function ‘get_fixed_ipv4_csum’:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing pointer to incomplete type
_u8 ipproto = iph->protocol;
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a74515604a ]
Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
