commit 1e4b50f06d upstream.
In order to have the padding fields actually usable in the future,
there have to be checks that user space doesn't supply non-zero garbage
there. It is also worth setting these padding fields to zero, unless
it is known that they have been already zeroed.
Cc: stable@vger.kernel.org # v5.15
Fixes: 5a20dd46b8 ("mctp: Be explicit about struct sockaddr_mctp padding")
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4ebddd654 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc7e5940aa upstream.
In orininal code, use 2 function spin_lock() and local_irq_save() to
protect the critical zone. But when enable the kernel debug config,
there are below inconsistent lock state detected.
================================
WARNING: inconsistent lock state
5.10.63-yocto-standard #1 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
lock_torture_wr/226 [HC0[0]:SC1[5]:HE1:SE0] takes:
ffff002005b2dd80 (&p->access_spinlock){+.?.}-{3:3}, at: qbman_swp_enqueue_multiple_mem_back+0x44/0x270
{SOFTIRQ-ON-W} state was registered at:
lock_acquire.part.0+0xf8/0x250
lock_acquire+0x68/0x84
_raw_spin_lock+0x68/0x90
qbman_swp_enqueue_multiple_mem_back+0x44/0x270
......
cryptomgr_test+0x38/0x60
kthread+0x158/0x164
ret_from_fork+0x10/0x38
irq event stamp: 4498
hardirqs last enabled at (4498): [<ffff800010fcf980>] _raw_spin_unlock_irqrestore+0x90/0xb0
hardirqs last disabled at (4497): [<ffff800010fcffc4>] _raw_spin_lock_irqsave+0xd4/0xe0
softirqs last enabled at (4458): [<ffff8000100108c4>] __do_softirq+0x674/0x724
softirqs last disabled at (4465): [<ffff80001005b2a4>] __irq_exit_rcu+0x190/0x19c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&p->access_spinlock);
<Interrupt>
lock(&p->access_spinlock);
*** DEADLOCK ***
So, in order to avoid deadlock, use the combined functions
spin_lock_irqsave/spin_unlock_irqrestore() to protect critical zone.
Fixes: 3b2abda7d2 ("soc: fsl: dpio: Replace QMAN array mode with ring mode enqueue")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e775eb9fc2 upstream.
When enable debug kernel configs,there will be calltrace as below:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id+0x20/0x30
CPU: 6 PID: 1 Comm: swapper/0 Not tainted 5.10.63-yocto-standard #1
Hardware name: NXP Layerscape LX2160ARDB (DT)
Call trace:
dump_backtrace+0x0/0x1a0
show_stack+0x24/0x30
dump_stack+0xf0/0x13c
check_preemption_disabled+0x100/0x110
debug_smp_processor_id+0x20/0x30
dpaa2_io_query_fq_count+0xdc/0x154
dpaa2_eth_stop+0x144/0x314
__dev_close_many+0xdc/0x160
__dev_change_flags+0xe8/0x220
dev_change_flags+0x30/0x70
ic_close_devs+0x50/0x78
ip_auto_config+0xed0/0xf10
do_one_initcall+0xac/0x460
kernel_init_freeable+0x30c/0x378
kernel_init+0x20/0x128
ret_from_fork+0x10/0x38
Based on comment in the context, it doesn't matter whether
preemption is disable or not. So, replace smp_processor_id()
with raw_smp_processor_id() to avoid above call trace.
Fixes: c89105c9b3 ("staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e37ef6dcdb upstream.
Commit 93618e344a ("soc: samsung: exynos-pmu: instantiate clkout
driver as MFD") adds a "devm_mfd_add_devices" call in the exynos-pmu
driver which depends on CONFIG_MFD_CORE. If no driver selects that
config, the build will fail if CONFIG_EXYNOS_PMU is enabled with the
following error:
drivers/soc/samsung/exynos-pmu.c:137: undefined reference to `devm_mfd_add_devices'
Fix this by making CONFIG_EXYNOS_PMU select CONFIG_MFD_CORE.
Fixes: 93618e344a ("soc: samsung: exynos-pmu: instantiate clkout driver as MFD")
Cc: <stable@vger.kernel.org>
Signed-off-by: David Virag <virag.david003@gmail.com>
Link: https://lore.kernel.org/r/20210909222812.108614-1-virag.david003@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00b06da29c upstream.
As Andy pointed out that there are races between
force_sig_info_to_task and sigaction[1] when force_sig_info_task. As
Kees discovered[2] ptrace is also able to change these signals.
In the case of seeccomp killing a process with a signal it is a
security violation to allow the signal to be caught or manipulated.
Solve this problem by introducing a new flag SA_IMMUTABLE that
prevents sigaction and ptrace from modifying these forced signals.
This flag is carefully made kernel internal so that no new ABI is
introduced.
Longer term I think this can be solved by guaranteeing short circuit
delivery of signals in this case. Unfortunately reliable and
guaranteed short circuit delivery of these signals is still a ways off
from being implemented, tested, and merged. So I have implemented a much
simpler alternative for now.
[1] https://lkml.kernel.org/r/b5d52d25-7bde-4030-a7b1-7c6f8ab90660@www.fastmail.com
[2] https://lkml.kernel.org/r/202110281136.5CE65399A7@keescook
Cc: stable@vger.kernel.org
Fixes: 307d522f5e ("signal/seccomp: Refactor seccomp signal and coredump generation")
Tested-by: Andrea Righi <andrea.righi@canonical.com>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95bf9d646c upstream.
When an instruction to save or restore a register from the stack fails
in _save_fp_context or _restore_fp_context return with -EFAULT. This
change was made to r2300_fpu.S[1] but it looks like it got lost with
the introduction of EX2[2]. This is also what the other implementation
of _save_fp_context and _restore_fp_context in r4k_fpu.S does, and
what is needed for the callers to be able to handle the error.
Furthermore calling do_exit(SIGSEGV) from bad_stack is wrong because
it does not terminate the entire process it just terminates a single
thread.
As the changed code was the only caller of arch/mips/kernel/syscall.c:bad_stack
remove the problematic and now unused helper function.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Maciej Rozycki <macro@orcam.me.uk>
Cc: linux-mips@vger.kernel.org
[1] 35938a00ba ("MIPS: Fix ISA I FP sigcontext access violation handling")
[2] f92722dc45 ("MIPS: Correct MIPS I FP sigcontext layout")
Cc: stable@vger.kernel.org
Fixes: f92722dc45 ("MIPS: Correct MIPS I FP sigcontext layout")
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lkml.kernel.org/r/20211020174406.17889-5-ebiederm@xmission.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fff53a551d upstream.
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d613f9f72 upstream.
The existence of sigkill_pending is a little silly as it is
functionally a duplicate of fatal_signal_pending that is used in
exactly one place.
Checking for pending fatal signals and returning early in ptrace_stop
is actively harmful. It casues the ptrace_stop called by
ptrace_signal to return early before setting current->exit_code.
Later when ptrace_signal reads the signal number from
current->exit_code is undefined, making it unpredictable what will
happen.
Instead rely on the fact that schedule will not sleep if there is a
pending signal that can awaken a task.
Removing the explict sigkill_pending test fixes fixes ptrace_signal
when ptrace_stop does not stop because current->exit_code is always
set to to signr.
Cc: stable@vger.kernel.org
Fixes: 3d749b9e67 ("ptrace: simplify ptrace_stop()->sigkill_pending() path")
Fixes: 1a669c2f16 ("Add arch_ptrace_stop")
Link: https://lkml.kernel.org/r/87pmsyx29t.fsf@disp2133
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b515d09705 upstream.
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ac601882 upstream.
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes: 314538041b ("rsi: fix AP mode with WPA failure due to encrypted EAPOL")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b14ed6e11 upstream.
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber: 000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes: 716b840c76 ("rsi: handle BT traffic in driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b51b02a3a upstream.
Daniel pointed me towards this function and there are multiple obvious problems
in the implementation.
First of all the retry loop is not working as intended. In general the retry
makes only sense if you grab the reference first and then check the sequence
values.
Then we should always also wait for the exclusive fence.
It's also good practice to keep the reference around when installing callbacks
to fences you don't own.
And last the whole implementation was unnecessary complex and rather hard to
understand which could lead to probably unexpected behavior of the IOCTL.
Fix all this by reworking the implementation from scratch. Dropping the
whole RCU approach and taking the lock instead.
Only mildly tested and needs a thoughtful review of the code.
Pushing through drm-misc-next to avoid merge conflicts and give the code
another round of testing.
v2: fix the reference counting as well
v3: keep the excl fence handling as is for stable
v4: back to testing all fences, drop RCU
v5: handle in and out separately
v6: add missing clear of events
v7: change coding style as suggested by Michel, drop unused variables
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Michel Dänzer <mdaenzer@redhat.com>
CC: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210720131110.88512-1-christian.koenig@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f971a85439 upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e3e59c31f upstream.
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f4eb8223 upstream.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 928265e360 upstream.
There is no reason to allow "syscore" devices to runtime-suspend
during system-wide PM transitions, because they are subject to the
same possible failure modes as any other devices in that respect.
Accordingly, change device_prepare() and device_complete() to call
pm_runtime_get_noresume() and pm_runtime_put(), respectively, for
"syscore" devices too.
Fixes: 057d51a126 ("Merge branch 'pm-sleep'")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3fd2c95c1 upstream.
We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.
After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.
Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.
Cc: stable@vger.kernel.org
Fixes: 512b191d96 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9e79b116c upstream.
This change fix the TX ack mechanism in various ways:
- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.
- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.
- This adds a sanity (paranoia?) check on the skb tx ack pointer.
- Resume TX queue if TX status tagged packet TX fails.
Cc: stable@vger.kernel.org
Fixes: fdf21cc371 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc0fd0acb6 upstream.
Until now, we have only ever seen the REG-category registry being used
on devices addressed with target ID 2. In fact, we have only ever seen
Surface Aggregator Module (SAM) HID devices with target ID 2. For those
devices, the registry also has to be addressed with target ID 2.
Some devices, like the new Surface Laptop Studio, however, address their
HID devices on target ID 1. As a result of this, any target ID 2
commands time out. This includes event management commands addressed to
the target ID 2 REG-category registry. For these devices, the registry
has to be addressed via target ID 1 instead.
We therefore assume that the target ID of the registry to be used
depends on the target ID of the respective device. Implement this
accordingly.
Note that we currently allow the surface HID driver to only load against
devices with target ID 2, so these timeouts are not happening (yet).
This is just a preparation step before we allow the driver to load
against all target IDs.
Cc: stable@vger.kernel.org # 5.14+
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20211021130904.862610-3-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5cd1fd604 upstream.
When clearing all existing pending tx slots, mt76_tx_complete_skb needs to
be used to free the skbs, to ensure that they are cleared from the status
list as well.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f042e4019 upstream.
Add support for the Surface Laptop Studio.
In contrast to previous Surface Laptop models, this one has its HID
devices attached to target ID 1 (instead of 2). It also has a couple
more of them, including a new notifier for when the pen is stashed /
taken out of its place, a "Sys Control" device, and two other
unidentified HID devices with unknown usages.
Battery and performance profile interfaces remain the same.
Cc: stable@vger.kernel.org # 5.14+
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20211021130904.862610-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 046178e726 upstream.
IFB originally depended on NET_CLS_ACT for traffic redirection.
But since v4.5, that may be achieved with NFT_FWD_NETDEV as well.
Fixes: 39e6dea28a ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.5+: bcfabee1af: netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a006acb931 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4db66499df ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1b9ca365d upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee35868 ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89f8765a11 upstream.
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16bef60a9 upstream.
The driver and its bindings, before commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a6 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a6 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db05ddf7f3 upstream.
You will get two decrements when the messages on a panic are sent, not
one, since commit 2033f68589 ("ipmi: Free receive messages when in an
oops") was added, but the watchdog code had a bug where it didn't set
the value properly.
Reported-by: Anton Lundin <glance@acc.umu.se>
Cc: <Stable@vger.kernel.org> # v5.4+
Fixes: 2033f68589 ("ipmi: Free receive messages when in an oops")
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbfcd13be5 upstream.
Current code contains a lot of racy patterns when converting an
ocontext's context structure to an SID. This is being done in a "lazy"
fashion, such that the SID is looked up in the SID table only when it's
first needed and then cached in the "sid" field of the ocontext
structure. However, this is done without any locking or memory barriers
and is thus unsafe.
Between commits 24ed7fdae6 ("selinux: use separate table for initial
SID lookup") and 66f8e2f03c ("selinux: sidtab reverse lookup hash
table"), this race condition lead to an actual observable bug, because a
pointer to the shared sid field was passed directly to
sidtab_context_to_sid(), which was using this location to also store an
intermediate value, which could have been read by other threads and
interpreted as an SID. In practice this caused e.g. new mounts to get a
wrong (seemingly random) filesystem context, leading to strange denials.
This bug has been spotted in the wild at least twice, see [1] and [2].
Fix the race condition by making all the racy functions use a common
helper that ensures the ocontext::sid accesses are made safely using the
appropriate SMP constructs.
Note that security_netif_sid() was populating the sid field of both
contexts stored in the ocontext, but only the first one was actually
used. The SELinux wiki's documentation on the "netifcon" policy
statement [3] suggests that using only the first context is intentional.
I kept only the handling of the first context here, as there is really
no point in doing the SID lookup for the unused one.
I wasn't able to reproduce the bug mentioned above on any kernel that
includes commit 66f8e2f03c, even though it has been reported that the
issue occurs with that commit, too, just less frequently. Thus, I wasn't
able to verify that this patch fixes the issue, but it makes sense to
avoid the race condition regardless.
[1] https://github.com/containers/container-selinux/issues/89
[2] https://lists.fedoraproject.org/archives/list/selinux@lists.fedoraproject.org/thread/6DMTAMHIOAOEMUAVTULJD45JZU7IBAFM/
[3] https://selinuxproject.org/page/NetworkStatements#netifcon
Cc: stable@vger.kernel.org
Cc: Xinjie Zheng <xinjie@google.com>
Reported-by: Sujithra Periasamy <sujithra@google.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 235cee1624 upstream.
Commit 112665286d ("KVM: PPC: Book3S HV: Context tracking exit guest
context before enabling irqs") moved guest_exit() into the interrupt
protected area to avoid wrong context warning (or worse). The problem is
that tick-based time accounting has not yet been updated at this point
(because it depends on the timer interrupt firing), so the guest time
gets incorrectly accounted to system time.
To fix the problem, follow the x86 fix in commit 1604571401 ("Defer
vtime accounting 'til after IRQ handling"), and allow host IRQs to run
before accounting the guest exit time.
In the case vtime accounting is enabled, this is not required because TB
is used directly for accounting.
Before this patch, with CONFIG_TICK_CPU_ACCOUNTING=y in the host and a
guest running a kernel compile, the 'guest' fields of /proc/stat are
stuck at zero. With the patch they can be observed increasing roughly as
expected.
Fixes: e233d54d4d ("KVM: booke: use __kvm_guest_exit")
Fixes: 112665286d ("KVM: PPC: Book3S HV: Context tracking exit guest context before enabling irqs")
Cc: stable@vger.kernel.org # 5.12+
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
[np: only required for tick accounting, add Book3E fix, tweak changelog]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211027142150.3711582-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
