[ Upstream commit 02a16aa135 ]
Commit
a7e1f67ed2 ("x86/msr: Filter MSR writes")
introduced a module parameter to disable writing to the MSR device file
and tainted the kernel upon writing. As MSR registers can be written by
the X86_IOC_WRMSR_REGS ioctl too, the same filtering and tainting should
be applied to the ioctl as well.
[ bp: Massage commit message and space out statements. ]
Fixes: a7e1f67ed2 ("x86/msr: Filter MSR writes")
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210127122456.13939-1-misono.tomohiro@jp.fujitsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9e38cabd ]
With some USB network adapters, such as DM96xx, the following message
is seen for each maximum size receive packet.
dwc2 ff540000.usb: dwc2_update_urb_state(): trimming xfer length
This happens because the packet size requested by the driver is 1522
bytes, wMaxPacketSize is 64, the dwc2 driver configures the chip to
receive 24*64 = 1536 bytes, and the chip does indeed send more than
1522 bytes of data. Since the event does not indicate an error condition,
the message is just noise. Demote it to debug level.
Fixes: 7359d482eb ("staging: HCD files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-4-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f74b68c61c ]
In some situations, the following error messages are reported.
dwc2 ff540000.usb: dwc2_hc_chhltd_intr_dma: Channel 1 - ChHltd set, but reason is unknown
dwc2 ff540000.usb: hcint 0x00000002, intsts 0x04000021
This is sometimes followed by:
dwc2 ff540000.usb: dwc2_update_urb_state_abn(): trimming xfer length
and then:
WARNING: CPU: 0 PID: 0 at kernel/v4.19/drivers/usb/dwc2/hcd.c:2913
dwc2_assign_and_init_hc+0x98c/0x990
The warning suggests that an odd buffer address is to be used for DMA.
After an error is observed, the receive buffer may be full
(urb->actual_length >= urb->length). However, the urb is still left in
the queue unless three errors were observed in a row. When it is queued
again, the dwc2 hcd code translates this into a 1-block transfer.
If urb->actual_length (ie the total expected receive length) is not
DMA-aligned, the buffer pointer programmed into the chip will be
unaligned. This results in the observed warning.
To solve the problem, abort input transactions after an error with
unknown cause if the entire packet was already received. This may be
a bit drastic, but we don't really know why the transfer was aborted
even though the entire packet was received. Aborting the transfer in
this situation is less risky than accepting a potentially corrupted
packet.
With this patch in place, the 'ChHltd set' and 'trimming xfer length'
messages are still observed, but there are no more transfer attempts
with odd buffer addresses.
Fixes: 151d0cbdbe ("usb: dwc2: make the scheduler handle excessive NAKs better")
Cc: Boris ARZUR <boris@konbu.org>
Cc: Douglas Anderson <dianders@chromium.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-3-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 415fa1c730 ]
The DWC2 documentation states that transfers with zero data length should
set the number of packets to 1 and the transfer length to 0. This is not
currently the case for inbound transfers: the transfer length is set to
the maximum packet length. This can have adverse effects if the chip
actually does transfer data as it is programmed to do. Follow chip
documentation and keep the transfer length set to 0 in that situation.
Fixes: 56f5b1cff2 ("staging: Core files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-2-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44f416879a ]
We have gpio_86 wired internally to the bandgap thermal shutdown
interrupt on 4430 like we have it on 4460 according to the TRM.
This can be found easily by searching for TSHUT.
For some reason the thermal shutdown interrupt was never added
for 4430, let's add it. I believe this is needed for the thermal
shutdown interrupt handler ti_bandgap_tshut_irq_handler() to call
orderly_poweroff().
Fixes: aa9bb4bb88 ("arm: dts: add omap4430 thermal data")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94e9dd43cf ]
Call of_node_put() to decrement the reference count of the child node
child_np when jumping out of the loop body of
for_each_available_child_of_node(), which is a macro that increments and
decrements the reference count of child node. If the loop is broken, the
reference of the child node should be dropped manually.
Fixes: 5a7c81547c ("memory: ti-aemif: introduce AEMIF driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210121090359.61763-1-bianpan2016@163.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28a758c861 ]
Jump to the label done to decrement the reference count of HCI device
hdev on path that the Inquiry procedure is interrupted.
Fixes: 3e13fa1e1f ("Bluetooth: Fix hci_inquiry ioctl usage")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17ad466259 ]
'am33xx_pm_rtc_setup()' allocates some resources that must be freed on the
error. Commit 2152fbbd47 ("soc: ti: pm33xx: Simplify RTC usage to prepare
to drop platform data") has introduced the use of these resources but has
only updated the remove function.
Fix the error handling path of the probe function now.
Fixes: 2152fbbd47 ("soc: ti: pm33xx: Simplify RTC usage to prepare to drop platform data")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de8681be2 ]
As per the kernel doc for usb_ep_dequeue(), it states that "this
routine is asynchronous, that is, it may return before the completion
routine runs". And indeed since v5.0 the dwc3 gadget driver updated
its behavior to place dequeued requests on to a cancelled list to be
given back later after the endpoint is stopped.
The free_ep() was incorrectly assuming that a request was ready to
be freed after calling dequeue which results in a use-after-free
in dwc3 when it traverses its cancelled list. Fix this by moving
the usb_ep_free_request() call to the callback itself in case the
ep is disabled.
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Reported-and-tested-by: Ferry Toth <fntoth@gmail.com>
Reviewed-and-tested-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210118084642.322510-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dfaea3811 ]
ACPICA commit 1a3a549286ea9db07d7ec700e7a70dd8bcc4354e
The macros to classify different AML exception codes are broken. For
instance,
ACPI_ENV_EXCEPTION(Status)
will always evaluate to zero due to
#define AE_CODE_ENVIRONMENTAL 0x0000
#define ACPI_ENV_EXCEPTION(Status) (Status & AE_CODE_ENVIRONMENTAL)
Similarly, ACPI_AML_EXCEPTION(Status) will evaluate to a non-zero
value for error codes of type AE_CODE_PROGRAMMER, AE_CODE_ACPI_TABLES,
as well as AE_CODE_AML, and not just AE_CODE_AML as the name suggests.
This commit fixes those checks.
Fixes: d46b6537f0 ("ACPICA: AML Parser: ignore all exceptions resulting from incorrect AML during table load")
Link: https://github.com/acpica/acpica/commit/1a3a5492
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6433083f5 ]
The gmac2phy is integrated with the PHY within the SoC. Any properties
related to this integration can be included in the .dtsi file, instead
of having board dts files specify them separately.
Add the clock_in_out property to specify the direction of the PHY clock.
This is the minimum required to have gmac2phy working on Linux. Other
examples include assigned-clocks, assigned-clock-rates, and
assigned-clock-parents properties, but the hardware default plus the
implementation requesting the appropriate clock rate also works.
Fixes: 9c4cc910fe ("ARM64: dts: rockchip: Add gmac2phy node support for rk3328")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210117100710.4857-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05f456286f ]
If 'cpufreq_register_driver()' fails, we must release the resources
allocated in 'brcm_avs_prepare_init()' as already done in the remove
function.
To do that, introduce a new function 'brcm_avs_prepare_uninit()' in order
to avoid code duplication. This also makes the code more readable (IMHO).
Fixes: de322e0859 ("cpufreq: brcmstb-avs-cpufreq: AVS CPUfreq driver for Broadcom STB SoCs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[ Viresh: Updated Subject ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3716a583fe ]
When the BMC150 accelerometer/magnetometer was added to the device tree,
the sensors were working without specifying any regulator supplies,
likely because the regulators were on by default and then never turned off.
For some reason, this is no longer the case for pm8916_l17, which prevents
the sensors from working in some cases.
Now that the bmc150_accel/bmc150_magn drivers can enable necessary
regulators, declare the necessary regulator supplies to make the sensors
work again.
Fixes: 079f81acf1 ("arm64: dts: qcom: msm8916-samsung-a2015: Add accelerometer/magnetometer")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210111175358.97171-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948c657cc4 ]
In contrast to the H6 (and later) manuals, the A64 datasheet does not
specify any limitations in the maximum possible frequency for eMMC
controllers.
However experimentation has found that a 150 MHz limit similar to other
SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist
for the MMC2 controller.
Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi.
The Pinebook seems to be the an odd exception, since it apparently seems
to work with 200 MHz as well, so overwrite this in its board .dts file.
Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works.
Fixes: 22be992fae ("arm64: allwinner: a64: Increase the MMC max frequency")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-7-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfe6c487b9 ]
The H6 manual explicitly lists a frequency limit of 150 MHz for the bus
frequency of the MMC controllers. So far we had no explicit limits in the
DT, which limited eMMC to the spec defined frequencies, or whatever the
driver defines (both Linux and FreeBSD use 52 MHz here).
Put those maximum frequencies in the SoC .dtsi, to allow higher speed
modes (which still would need to be explicitly enabled, per board).
Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed
200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably.
Fixes: 8f54bd1595 ("arm64: allwinner: h6: add device tree nodes for MMC controllers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-6-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 941432d007 ]
The SD card on the SoPine SoM module is somewhat concealed, so was
originally defined as "non-removable".
However there is a working card-detect pin (tested on two different
SoM versions), and in certain SoM base boards it might be actually
accessible at runtime.
Also the Pine64-LTS shares the SoPine base .dtsi, so inherited the
non-removable flag, even though the SD card slot is perfectly accessible
and usable there. (It turns out that just *my* board has a broken card
detect switch, so I originally thought CD wouldn't work on the LTS.)
Drop the "non-removable" flag to describe the SD card slot properly.
Fixes: c3904a2698 ("arm64: allwinner: a64: add DTSI file for SoPine SoM")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-5-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da2fb8457f ]
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the H6 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: eabb3d424b ("arm64: dts: allwinner: h6: add USB2-related device nodes")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-3-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc72570747 ]
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the A64 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this. Remove the part from the Pinebook DTS which already had
this property.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: dc03a047df ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-2-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 025822884a ]
The timing-adjustment clock only has to be enabled when a) there is a
2ns RX delay configured using device-tree and b) the phy-mode indicates
that the RX delay should be enabled.
Only enable the RX delay if both are true, instead of (by accident) also
enabling it when there's the 2ns RX delay configured but the phy-mode
incicates that the RX delay is not used.
Fixes: 9308c47640 ("net: stmmac: dwmac-meson8b: add support for the RX delay configuration")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 826e6faf49 ]
Unlike most MSM8916 boards, samsung-a5u uses WCN3660B instead of
WCN3620 to support the 5 GHz band additionally.
WCN3660B has similar requirements as WCN3620, but it needs the XO
clock to run at 48 MHz instead of 19.2 MHz. So far it was possible
to describe that configuration using the qcom,wcn3680 compatible.
However, as of commit 8490987bdb ("wcn36xx: Hook and identify RF_IRIS_WCN3680"),
the wcn36xx driver will now use the qcom,wcn3680 compatible
to enable functionality specific to WCN3680. In particular,
WCN3680 supports 802.11ac, which is not available in WCN3660B.
Use the new qcom,wcn3660b compatible to describe the chip properly.
Fixes: 0d70519991 ("arm64: dts: msm8916-samsung-a5u: Override iris compatible")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106102134.59801-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71f8e70755 ]
When __le32_to_cpu() fails, qca_memdump should be freed
just like when vmalloc() fails.
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fea2eb2f5 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 9589f7721e ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e98e2367df ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-7-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e6a5467c ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-4-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 437ae60947 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: faaf348ef4 ("ARM: dts: Add board dts file for exynos3250-rinato")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-3-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8528cda2b7 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: e0cefb3f79 ("ARM: dts: add board dts file for Exynos3250-based Monk board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-2-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb31334687 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: b004a34bd0 ("ARM: dts: exynos: Add exynos3250-artik5 dtsi file for ARTIK5 module")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-1-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db030c5a96 ]
The Bluetooth chip is capable of operating at 4Mbps, but the
max-speed setting was on the UART node instead of the Bluetooth
node, so the chip didn't operate at the correct speed resulting
in choppy audio. Fix this by setting the max-speed in the proper
node.
Fixes: a1d8a344f1 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201213183759.223246-3-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5687c6440 ]
Looks like this was missed when patching the source to clear the structures
throughout, causing this one instance to clear the struct after the response
id is assigned.
Fixes: eddb773211 ("Bluetooth: A2MP: Fix not initializing all members")
Signed-off-by: Christopher William Snowhill <chris@kode54.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afe0b1c864 ]
In hci_uart_write_work, there is a loop/goto checking the value of
HCI_UART_TX_WAKEUP. If HCI_UART_TX_WAKEUP is set again, it keeps trying
hci_uart_dequeue; otherwise, it clears HCI_UART_SENDING and returns.
In hci_uart_tx_wakeup, if HCI_UART_SENDING is already set, it sets
HCI_UART_TX_WAKEUP, skips schedule_work and assumes the running/pending
hci_uart_write_work worker will do hci_uart_dequeue properly.
However, if the HCI_UART_SENDING check in hci_uart_tx_wakeup is done after
the loop breaks, but before HCI_UART_SENDING is cleared in
hci_uart_write_work, the schedule_work is skipped incorrectly.
Fix this race by changing the order of HCI_UART_SENDING and
HCI_UART_TX_WAKEUP modification.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: 82f5169bf3 ("Bluetooth: hci_uart: add serdev driver support library")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a39a927be ]
Some resource should be released in the error handling path of the probe
function, as already done in the remove function.
The remove function was fixed in commit 5052de8def ("soc: qcom: smd:
Transition client drivers from smd to rpmsg")
Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 700cb70730 upstream.
The PCM stop operation sets the stop_operating flag for indicating the
sync_stop post-process. This flag is, however, set unconditionally
even if the PCM trigger weren't issued. This may lead to
inconsistency in the driver side.
Correct the code to set stop_operating flag only after the trigger
STOP is actually called.
Fixes: 1e850beea2 ("ALSA: pcm: Add the support for sync-stop operation")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203656.15959-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c87c1a49c upstream.
The current PCM code calls the sync_stop at the resume action due to
the analogy to the PCM prepare call pattern. But, it makes little
sense, as the sync should have been done rather at the suspend time,
not at the resume time.
This patch corrects the sync_stop call at suspend/resume to assure the
sync before finishing the suspend.
Fixes: 1e850beea2 ("ALSA: pcm: Add the support for sync-stop operation")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203656.15959-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
