[ Upstream commit 631b010abc ]
Inheriting the ADC BIAS current settings from the BIOS instead of
hardcoding then causes the AXP288 to disable charging (I think it
mis-detects an overheated battery) on at least one model tablet.
So lets go back to hard coding the values, this reverts
commit fa2849e964 ("iio: adc: axp288: Drop bogus
AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not
working on the model tablet in question.
The exact cause is not fully understood, hence the revert to a known working
state.
Cc: stable@vger.kernel.org
Reported-by: Umberto Ixxo <sfumato1977@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91a825290c ]
The function rds_ib_setup_qp is calling rds_ib_get_client_data and
should correspondingly call rds_ib_dev_put. This call was lost in
the non-error path with the introduction of error handling done in
commit 3b12f73a5c ("rds: ib: add error handle")
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e490657c7 ]
The vif->idx value is always 0 for two interfaces.
wl->vif_num = 0;
loop {
...
vif->idx = wl->vif_num;
...
wl->vif_num = i;
....
i++;
...
}
At present, vif->idx is assigned the value of wl->vif_num
at the beginning of this block and device is initialized
based on this index value.
In the next iteration, wl->vif_num is still 0 as it is only updated
later but gets assigned to vif->idx in the beginning. This causes problems
later when we try to reference a particular interface and also while
configuring the firmware.
This patch moves the assignment to vif->idx from the beginning
of the block to after wl->vif_num is updated with latest value of i.
Fixes: commit 735bb39ca3 ("staging: wilc1000: simplify vif[i]->ndev accesses")
Cc: <stable@vger.kernel.org>
Signed-off-by: Aditya Shankar <aditya.shankar@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5790eabc6e ]
Add more stubs to make it build.
Fixes: 81fbfe8a ("ptr_ring: use kmalloc_array()")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c07c1a0f68 ]
The TOP "aclk400_mscl" clock should be kept enabled all the time
to allow proper access to power management control for MSC power
domain and devices that are a part of it. This change is required
for the scaler to work properly after domain power on/off sequence.
Fixes: 318fa46cc6 ("clk/samsung: exynos542x: mark some clocks as critical")
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee249b4554 ]
IRQ_NOAUTOEN cannot be used with shared IRQs, since commit 04c848d398
("genirq: Warn when IRQ_NOAUTOEN is used with shared interrupts") and
kernel now throws a warn dump. But OMAP DWC3 driver uses this flag. As
per commit 12a7f17fac ("usb: dwc3: omap: fix race of pm runtime with
irq handler in probe") that introduced this flag, PM runtime can race
with IRQ handler when deferred probing happens due to extcon,
therefore IRQ_NOAUTOEN needs to be set so that irq is not enabled until
extcon is registered.
Remove setting of IRQ_NOAUTOEN and move the registration of
shared irq to a point after dwc3_omap_extcon_register() and
of_platform_populate(). This avoids possibility of probe deferring and
above said race condition.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7d44c36a6 ]
The commit b8b9c974af ("usb: renesas_usbhs: gadget: disable all eps
when the driver stops") causes the unused-but-set-variable warning.
But, if the usbhsg_ep_disable() will return non-zero value, udc/core.c
doesn't clear the ep->enabled flag. So, this driver should not return
non-zero value, if the pipe is zero because this means the pipe is
already disabled. Otherwise, the ep->enabled flag is never cleared
when the usbhsg_ep_disable() is called by the renesas_usbhs driver first.
Fixes: b8b9c974af ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Fixes: 11432050f0 ("usb: renesas_usbhs: gadget: fix NULL pointer dereference in ep_disable()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14a8d4bfc2 ]
This patch fixes an issue that the spin_lock_init() is not called
for almost all pipes. Otherwise, the lockdep output the following
message when we connect a usb cable using g_ncm:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Fixes: b8b9c974af ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6377ed0bba ]
spin_lock/unlock of health->wq_lock should be IRQ safe.
It was changed to spin_lock_irqsave since adding commit 0179720d6b
("net/mlx5: Introduce trigger_health_work function") which uses
spin_lock from asynchronous event (IRQ) context.
Thus, all spin_lock/unlock of health->wq_lock should have been moved
to IRQ safe mode.
However, one occurrence on new code using this lock missed that
change, resulting in possible deadlock:
kernel: Possible unsafe locking scenario:
kernel: CPU0
kernel: ----
kernel: lock(&(&health->wq_lock)->rlock);
kernel: <Interrupt>
kernel: lock(&(&health->wq_lock)->rlock);
kernel: #012 *** DEADLOCK ***
Fixes: 2a0165a034 ("net/mlx5: Cancel delayed recovery work when unloading the driver")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7598f8bc13 ]
In commit 613f050d68 ("perf probe: Fix to probe on gcc generated
functions in modules"), the offset from symbol is, incorrectly, added
to the trace point address. This leads to incorrect probe trace points
for inlined functions and when using relative line number on symbols.
Prior this patch:
$ perf probe -m nf_nat -D in_range
p:probe/in_range nf_nat:in_range.isra.9+0
$ perf probe -m i40e -D i40e_clean_rx_irq
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+2212
$ perf probe -m i40e -D i40e_clean_rx_irq:16
p:probe/i40e_clean_rx_irq i40e:i40e_lan_xmit_frame+626
After:
$ perf probe -m nf_nat -D in_range
p:probe/in_range nf_nat:in_range.isra.9+0
$ perf probe -m i40e -D i40e_clean_rx_irq
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+1106
$ perf probe -m i40e -D i40e_clean_rx_irq:16
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+2665
Committer testing:
Using 'pfunct', a tool found in the 'dwarves' package [1], one can ask what are
the functions that while not being explicitely marked as inline, were inlined
by the compiler:
# pfunct --cc_inlined /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko | head
__ew32
e1000_regdump
e1000e_dump_ps_pages
e1000_desc_unused
e1000e_systim_to_hwtstamp
e1000e_rx_hwtstamp
e1000e_update_rdt_wa
e1000e_update_tdt_wa
e1000_put_txbuf
e1000_consume_page
Then ask 'perf probe' to produce the kprobe_tracer probe definitions for two of
them:
# perf probe -m e1000e -D e1000e_rx_hwtstamp
p:probe/e1000e_rx_hwtstamp e1000e:e1000_receive_skb+74
# perf probe -m e1000e -D e1000_consume_page
p:probe/e1000_consume_page e1000e:e1000_clean_jumbo_rx_irq+876
p:probe/e1000_consume_page_1 e1000e:e1000_clean_jumbo_rx_irq+1506
p:probe/e1000_consume_page_2 e1000e:e1000_clean_rx_irq_ps+1074
Now lets concentrate on the 'e1000_consume_page' one, that was inlined twice in
e1000_clean_jumbo_rx_irq(), lets see what readelf says about the DWARF tags for
that function:
$ readelf -wi /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko
<SNIP>
<1><13e27b>: Abbrev Number: 121 (DW_TAG_subprogram)
<13e27c> DW_AT_name : (indirect string, offset: 0xa8945): e1000_clean_jumbo_rx_irq
<13e287> DW_AT_low_pc : 0x17a30
<3><13e6ef>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13e6f0> DW_AT_abstract_origin: <0x13ed2c>
<13e6f4> DW_AT_low_pc : 0x17be6
<SNIP>
<1><13ed2c>: Abbrev Number: 142 (DW_TAG_subprogram)
<13ed2e> DW_AT_name : (indirect string, offset: 0xa54c3): e1000_consume_page
So, the first time in e1000_clean_jumbo_rx_irq() where e1000_consume_page() is
inlined is at PC 0x17be6, which subtracted from e1000_clean_jumbo_rx_irq()'s
address, gives us the offset we should use in the probe definition:
0x17be6 - 0x17a30 = 438
but above we have 876, which is twice as much.
Lets see the second inline expansion of e1000_consume_page() in
e1000_clean_jumbo_rx_irq():
<3><13e86e>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13e86f> DW_AT_abstract_origin: <0x13ed2c>
<13e873> DW_AT_low_pc : 0x17d21
0x17d21 - 0x17a30 = 753
So we where adding it at twice the offset from the containing function as we
should.
And then after this patch:
# perf probe -m e1000e -D e1000e_rx_hwtstamp
p:probe/e1000e_rx_hwtstamp e1000e:e1000_receive_skb+37
# perf probe -m e1000e -D e1000_consume_page
p:probe/e1000_consume_page e1000e:e1000_clean_jumbo_rx_irq+438
p:probe/e1000_consume_page_1 e1000e:e1000_clean_jumbo_rx_irq+753
p:probe/e1000_consume_page_2 e1000e:e1000_clean_jumbo_rx_irq+1353
#
Which matches the two first expansions and shows that because we were
doubling the offset it would spill over the next function:
readelf -sw /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko
673: 0000000000017a30 1626 FUNC LOCAL DEFAULT 2 e1000_clean_jumbo_rx_irq
674: 0000000000018090 2013 FUNC LOCAL DEFAULT 2 e1000_clean_rx_irq_ps
This is the 3rd inline expansion of e1000_consume_page() in
e1000_clean_jumbo_rx_irq():
<3><13ec77>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13ec78> DW_AT_abstract_origin: <0x13ed2c>
<13ec7c> DW_AT_low_pc : 0x17f79
0x17f79 - 0x17a30 = 1353
So:
0x17a30 + 2 * 1353 = 0x184c2
And:
0x184c2 - 0x18090 = 1074
Which explains the bogus third expansion for e1000_consume_page() to end up at:
p:probe/e1000_consume_page_2 e1000e:e1000_clean_rx_irq_ps+1074
All fixed now :-)
[1] https://git.kernel.org/pub/scm/devel/pahole/pahole.git/
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 613f050d68 ("perf probe: Fix to probe on gcc generated functions in modules")
Link: http://lkml.kernel.org/r/20170621164134.5701-1-bjorn.topel@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a1ac110c2 ]
Since commit 18e7a45af9 ("perf/x86: Reject non sampling events with
precise_ip") returns -EINVAL for sys_perf_event_open() with an attribute
with (attr.precise_ip > 0 && attr.sample_period == 0), just like is done
in the routine used to probe the max precise level when no events were
passed to 'perf record' or 'perf top', i.e.:
perf_evsel__new_cycles()
perf_event_attr__set_max_precise_ip()
The x86 code, in x86_pmu_hw_config(), which is called all the way from
sys_perf_event_open() did, starting with the aforementioned commit:
/* There's no sense in having PEBS for non sampling events: */
if (!is_sampling_event(event))
return -EINVAL;
Which makes it fail for cycles:ppp, cycles:pp and cycles:p, always using
just the non precise cycles variant.
To make sure that this is the case, I tested it, before this patch,
with:
# perf probe -L x86_pmu_hw_config
<x86_pmu_hw_config@/home/acme/git/linux/arch/x86/events/core.c:0>
0 int x86_pmu_hw_config(struct perf_event *event)
1 {
2 if (event->attr.precise_ip) {
<SNIP>
17 if (event->attr.precise_ip > precise)
18 return -EOPNOTSUPP;
/* There's no sense in having PEBS for non sampling events: */
21 if (!is_sampling_event(event))
22 return -EINVAL;
}
<SNIP>
# perf probe x86_pmu_hw_config:22
Added new events:
probe:x86_pmu_hw_config (on x86_pmu_hw_config:22)
probe:x86_pmu_hw_config_1 (on x86_pmu_hw_config:22)
You can now use it in all perf tools, such as:
perf record -e probe:x86_pmu_hw_config_1 -aR sleep 1
# perf trace -e perf_event_open,probe:x86_pmu_hwconfig*/max-stack=16/ perf record usleep 1
0.000 ( 0.015 ms): perf/4150 perf_event_open(attr_uptr: 0x7ffebc8ba110, cpu: -1, group_fd: -1 ) ...
0.015 ( ): probe:x86_pmu_hw_config:(ffffffff9c0065e1))
x86_pmu_hw_config ([kernel.kallsyms])
hsw_hw_config ([kernel.kallsyms])
x86_pmu_event_init ([kernel.kallsyms])
perf_try_init_event ([kernel.kallsyms])
perf_event_alloc ([kernel.kallsyms])
SYSC_perf_event_open ([kernel.kallsyms])
sys_perf_event_open ([kernel.kallsyms])
do_syscall_64 ([kernel.kallsyms])
return_from_SYSCALL_64 ([kernel.kallsyms])
syscall (/usr/lib64/libc-2.24.so)
perf_event_attr__set_max_precise_ip (/home/acme/bin/perf)
perf_evsel__new_cycles (/home/acme/bin/perf)
perf_evlist__add_default (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
handle_internal_command (/home/acme/bin/perf)
0.000 ( 0.021 ms): perf/4150 ... [continued]: perf_event_open()) = -1 EINVAL Invalid argument
0.023 ( 0.002 ms): perf/4150 perf_event_open(attr_uptr: 0x7ffebc8ba110, cpu: -1, group_fd: -1 ) ...
0.025 ( ): probe:x86_pmu_hw_config:(ffffffff9c0065e1))
x86_pmu_hw_config ([kernel.kallsyms])
hsw_hw_config ([kernel.kallsyms])
x86_pmu_event_init ([kernel.kallsyms])
perf_try_init_event ([kernel.kallsyms])
perf_event_alloc ([kernel.kallsyms])
SYSC_perf_event_open ([kernel.kallsyms])
sys_perf_event_open ([kernel.kallsyms])
do_syscall_64 ([kernel.kallsyms])
return_from_SYSCALL_64 ([kernel.kallsyms])
syscall (/usr/lib64/libc-2.24.so)
perf_event_attr__set_max_precise_ip (/home/acme/bin/perf)
perf_evsel__new_cycles (/home/acme/bin/perf)
perf_evlist__add_default (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
handle_internal_command (/home/acme/bin/perf)
0.023 ( 0.004 ms): perf/4150 ... [continued]: perf_event_open()) = -1 EINVAL Invalid argument
0.028 ( 0.002 ms): perf/4150 perf_event_open(attr_uptr: 0x7ffebc8ba110, cpu: -1, group_fd: -1 ) ...
0.030 ( ): probe:x86_pmu_hw_config:(ffffffff9c0065e1))
x86_pmu_hw_config ([kernel.kallsyms])
hsw_hw_config ([kernel.kallsyms])
x86_pmu_event_init ([kernel.kallsyms])
perf_try_init_event ([kernel.kallsyms])
perf_event_alloc ([kernel.kallsyms])
SYSC_perf_event_open ([kernel.kallsyms])
sys_perf_event_open ([kernel.kallsyms])
do_syscall_64 ([kernel.kallsyms])
return_from_SYSCALL_64 ([kernel.kallsyms])
syscall (/usr/lib64/libc-2.24.so)
perf_event_attr__set_max_precise_ip (/home/acme/bin/perf)
perf_evsel__new_cycles (/home/acme/bin/perf)
perf_evlist__add_default (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
handle_internal_command (/home/acme/bin/perf)
0.028 ( 0.004 ms): perf/4150 ... [continued]: perf_event_open()) = -1 EINVAL Invalid argument
41.018 ( 0.012 ms): perf/4150 perf_event_open(attr_uptr: 0x7ffebc8b5dd0, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
41.065 ( 0.011 ms): perf/4150 perf_event_open(attr_uptr: 0x3c7db78, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
41.080 ( 0.006 ms): perf/4150 perf_event_open(attr_uptr: 0x3c7db78, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
41.103 ( 0.010 ms): perf/4150 perf_event_open(attr_uptr: 0x3c4e748, pid: 4151 (perf), group_fd: -1, flags: FD_CLOEXEC) = 4
41.115 ( 0.006 ms): perf/4150 perf_event_open(attr_uptr: 0x3c4e748, pid: 4151 (perf), cpu: 1, group_fd: -1, flags: FD_CLOEXEC) = 5
41.122 ( 0.004 ms): perf/4150 perf_event_open(attr_uptr: 0x3c4e748, pid: 4151 (perf), cpu: 2, group_fd: -1, flags: FD_CLOEXEC) = 6
41.128 ( 0.008 ms): perf/4150 perf_event_open(attr_uptr: 0x3c4e748, pid: 4151 (perf), cpu: 3, group_fd: -1, flags: FD_CLOEXEC) = 8
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.017 MB perf.data (2 samples) ]
#
I.e. that return -EINVAL in x86_pmu_hw_config() is hit three times.
So fix it by just setting attr.sample_period
Now, after this patch:
# perf trace --max-stack=2 -e perf_event_open,probe:x86_pmu_hw_config* perf record usleep 1
[ perf record: Woken up 1 times to write data ]
0.000 ( 0.017 ms): perf/8469 perf_event_open(attr_uptr: 0x7ffe36c27d10, pid: -1, cpu: 3, group_fd: -1, flags: FD_CLOEXEC) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_event_open_cloexec_flag (/home/acme/bin/perf)
0.050 ( 0.031 ms): perf/8469 perf_event_open(attr_uptr: 0x24ebb78, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_evlist__config (/home/acme/bin/perf)
0.092 ( 0.040 ms): perf/8469 perf_event_open(attr_uptr: 0x24ebb78, pid: -1, group_fd: -1, flags: FD_CLOEXEC) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_evlist__config (/home/acme/bin/perf)
0.143 ( 0.007 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, cpu: -1, group_fd: -1 ) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_event_attr__set_max_precise_ip (/home/acme/bin/perf)
0.161 ( 0.007 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, pid: 8470 (perf), group_fd: -1, flags: FD_CLOEXEC) = 4
syscall (/usr/lib64/libc-2.24.so)
perf_evsel__open (/home/acme/bin/perf)
0.171 ( 0.005 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, pid: 8470 (perf), cpu: 1, group_fd: -1, flags: FD_CLOEXEC) = 5
syscall (/usr/lib64/libc-2.24.so)
perf_evsel__open (/home/acme/bin/perf)
0.180 ( 0.007 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, pid: 8470 (perf), cpu: 2, group_fd: -1, flags: FD_CLOEXEC) = 6
syscall (/usr/lib64/libc-2.24.so)
perf_evsel__open (/home/acme/bin/perf)
0.190 ( 0.005 ms): perf/8469 perf_event_open(attr_uptr: 0x24bc748, pid: 8470 (perf), cpu: 3, group_fd: -1, flags: FD_CLOEXEC) = 8
syscall (/usr/lib64/libc-2.24.so)
perf_evsel__open (/home/acme/bin/perf)
[ perf record: Captured and wrote 0.017 MB perf.data (7 samples) ]
#
The probe one called from perf_event_attr__set_max_precise_ip() works
the first time, with attr.precise_ip = 3, wit hthe next ones being the
per cpu ones for the cycles:ppp event.
And here is the text from a report and alternative proposed patch by
Thomas-Mich Richter:
---
On s390 the counter and sampling facility do not support a precise IP
skid level and sometimes returns EOPNOTSUPP when structure member
precise_ip in struct perf_event_attr is not set to zero.
On s390 commnd 'perf record -- true' fails with error EOPNOTSUPP. This
happens only when no events are specified on command line.
The functions called are
...
--> perf_evlist__add_default
--> perf_evsel__new_cycles
--> perf_event_attr__set_max_precise_ip
The last function determines the value of structure member precise_ip by
invoking the perf_event_open() system call and checking the return code.
The first successful open is the value for precise_ip.
However the value is determined without setting member sample_period and
indicates no sampling.
On s390 the counter facility and sampling facility are different. The
above procedure determines a precise_ip value of 3 using the counter
facility. Later it uses the sampling facility with a value of 3 and
fails with EOPNOTSUPP.
---
v2: Older compilers (e.g. gcc 4.4.7) don't support referencing members
of unnamed union members in the container struct initialization, so
move from:
struct perf_event_attr attr = {
...
.sample_period = 1,
};
to right after it as:
struct perf_event_attr attr = {
...
};
attr.sample_period = 1;
v3: We need to reset .sample_period to 0 to let the users of
perf_evsel__new_cycles() to properly setup attr.sample_period or
attr.sample_freq. Reported by Ingo Molnar.
Reported-and-Acked-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: 18e7a45af9 ("perf/x86: Reject non sampling events with precise_ip")
Link: http://lkml.kernel.org/n/tip-yv6nnkl7tzqocrm0hl3x7vf1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ce59b16b4 ]
When wait for firmware init fails, previous code would mistakenly
return success and cause inconsistency in the driver state.
Fixes: 6c780a0267 ("net/mlx5: Wait for FW readiness before initializing command interface")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e58edaa486 ]
Helmut reported a bug about division by zero while
running traffic and doing physical cable pull test.
When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is division by zero.
This patch prevent this division for both ppms and epms.
Fixes: c3164d2fc4 ("net/mlx5e: Added BW check for DIM decision mechanism")
Reported-by: Helmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 452e62b71f ]
Before this, we use 'filled' mode here, ie. if all range has been
filled with EXTENT_DEFRAG bits, get to clear it, but if the defrag
range joins the adjacent delalloc range, then we'll have EXTENT_DEFRAG
bits in extent_state until releasing this inode's pages, and that
prevents extent_data from being freed.
This clears the bit if any was found within the ordered extent.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 594238158b ]
The current comparison of entry < 0 will never be true since entry is an
unsigned integer. Make entry an int to ensure -ve error return values
from the call to jumbo_frm are correctly being caught.
Detected by CoverityScan, CID#1238760 ("Macro compares unsigned to 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bd2bbc01d ]
gcc 7.1 reports the following warning:
block/elevator.c: In function ‘elv_register’:
block/elevator.c:898:5: warning: ‘snprintf’ output may be truncated before the last format character [-Wformat-truncation=]
"%s_io_cq", e->elevator_name);
^~~~~~~~~~
block/elevator.c:897:3: note: ‘snprintf’ output between 7 and 22 bytes into a destination of size 21
snprintf(e->icq_cache_name, sizeof(e->icq_cache_name),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s_io_cq", e->elevator_name);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The bug is that the name of the icq_cache is 6 characters longer than
the elevator name, but only ELV_NAME_MAX + 5 characters were reserved
for it --- so in the case of a maximum-length elevator name, the 'q'
character in "_io_cq" would be truncated by snprintf(). Fix it by
reserving ELV_NAME_MAX + 6 characters instead.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7dfee2433 ]
The description of the CSI_SEL bit in the i.MX6 reference manual is
incorrect. It states "This bit defines which CSI is the input to the
IC. This bit is effective only if IC_INPUT is bit cleared".
From experiment it was found this is in fact not correct. The CSI_SEL
bit selects which CSI is input to _both_ the VDIC _and_ the IC. If the
IC_INPUT bit is set so that the IC is receiving from the VDIC, the IC
ignores the CSI_SEL bit, but CSI_SEL still selects which CSI the VDIC
receives from in that case.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06a4b6d009 ]
As reported by Patrice, the header layout of the decompressor is
incorrect when building for v7-M. In this case, the __nop macro
resolves to 'mov r0, r0', which is emitted as a narrow encoding,
resulting in the header data fields to end up at lower offsets than
required.
Given the variety of targets we need to support with the same code,
the startup sequence is a bit of a jumble, and uses instructions
and macros whose encoding widths cannot be specified (badr), or only
exist in a narrow encoding (bx)
So force the use of a wide encoding in __nop, and replace the start
sequence with a simple jump to the label marking the start of code,
preceded by a Thumb2 mode switch if required (using explicit wide
encodings where appropriate). The label itself can be moved to the
start of code [where it belongs] due to the larger range of branch
instructions as compared to adr instructions.
Reported-by: Patrice CHOTARD <patrice.chotard@st.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae1d557d8f ]
A SoC variant of Geode GX1, notably NSC branded SC1100, seems to
report an inverted Device ID in its DIR0 configuration register,
specifically 0xb instead of the expected 0x4.
Catch this presumably quirky version so it's properly recognized
as GX1 and has its cache switched to write-back mode, which provides
a significant performance boost in most workloads.
SC1100's datasheet "Geode™ SC1100 Information Appliance On a Chip",
states in section 1.1.7.1 "Device ID" that device identification
values are specified in SC1100's device errata. These, however,
seem to not have been publicly released.
Wading through a number of boot logs and /proc/cpuinfo dumps found on
pastebin and blogs, this patch should mostly be relevant for a number
of now admittedly aging Soekris NET4801 and PC Engines WRAP devices,
the latter being the platform this issue was discovered on.
Performance impact was verified using "openssl speed", with
write-back caching scaling throughput between -3% and +41%.
Signed-off-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1496596719.26725.14.camel@student.kit.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bd7ef0b03 ]
Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.
This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7cf69ae17 ]
ata_parse_force_one() was incorrectly comparing @p to @endp when it
should have been comparing @id. The only consequence is that it may
end up using an invalid port number in "libata.force" module param
instead of rejecting it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Petru-Florin Mihancea <petrum@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195785
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a7c0a6438 ]
When starting or stopping an aggregation session, one of the steps
is that the driver calls back to mac80211 that the start/stop can
proceed. This is handled by queueing up a fake SKB and processing
it from the normal iface/sdata work. Since this isn't flushed when
disassociating, the following race is possible:
* associate
* start aggregation session
* driver callback
* disassociate
* associate again to the same AP
* callback processing runs, leading to a WARN_ON() that
the TID hadn't requested aggregation
If the second association isn't to the same AP, there would only
be a message printed ("Could not find station: <addr>"), but the
same race could happen.
Fix this by not going the whole detour with a fake SKB etc. but
simply looking up the aggregation session in the driver callback,
marking it with a START_CB/STOP_CB bit and then scheduling the
regular aggregation work that will now process these bits as well.
This also simplifies the code and gets rid of the whole problem
with allocation failures of said skb, which could have left the
session in limbo.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a71677691 ]
Element size in the manifest should be updated for each token, so that the
loop can parse all the string elements in the manifest. This was not
happening when more than two string elements appear consecutively, as it is
not updated with correct string element size. Fixed with this patch.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4497a224f7 ]
The hi6220_reset driver can be built as a standalone module
yet it cannot be loaded because it depends on GPL exported symbols.
Lets set the module license so that the module loads, and things like
the on-board kirin drm starts working.
Signed-off-by: Jeremy Linton <lintonrjeremy@gmail.com>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4751832da9 ]
[BUG]
Cycle mount btrfs can cause fiemap to return different result.
Like:
# mount /dev/vdb5 /mnt/btrfs
# dd if=/dev/zero bs=16K count=4 oflag=dsync of=/mnt/btrfs/file
# xfs_io -c "fiemap -v" /mnt/btrfs/file
/mnt/test/file:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 25088..25215 128 0x1
# umount /mnt/btrfs
# mount /dev/vdb5 /mnt/btrfs
# xfs_io -c "fiemap -v" /mnt/btrfs/file
/mnt/test/file:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..31]: 25088..25119 32 0x0
1: [32..63]: 25120..25151 32 0x0
2: [64..95]: 25152..25183 32 0x0
3: [96..127]: 25184..25215 32 0x1
But after above fiemap, we get correct merged result if we call fiemap
again.
# xfs_io -c "fiemap -v" /mnt/btrfs/file
/mnt/test/file:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 25088..25215 128 0x1
[REASON]
Btrfs will try to merge extent map when inserting new extent map.
btrfs_fiemap(start=0 len=(u64)-1)
|- extent_fiemap(start=0 len=(u64)-1)
|- get_extent_skip_holes(start=0 len=64k)
| |- btrfs_get_extent_fiemap(start=0 len=64k)
| |- btrfs_get_extent(start=0 len=64k)
| | Found on-disk (ino, EXTENT_DATA, 0)
| |- add_extent_mapping()
| |- Return (em->start=0, len=16k)
|
|- fiemap_fill_next_extent(logic=0 phys=X len=16k)
|
|- get_extent_skip_holes(start=0 len=64k)
| |- btrfs_get_extent_fiemap(start=0 len=64k)
| |- btrfs_get_extent(start=16k len=48k)
| | Found on-disk (ino, EXTENT_DATA, 16k)
| |- add_extent_mapping()
| | |- try_merge_map()
| | Merge with previous em start=0 len=16k
| | resulting em start=0 len=32k
| |- Return (em->start=0, len=32K) << Merged result
|- Stripe off the unrelated range (0~16K) of return em
|- fiemap_fill_next_extent(logic=16K phys=X+16K len=16K)
^^^ Causing split fiemap extent.
And since in add_extent_mapping(), em is already merged, in next
fiemap() call, we will get merged result.
[FIX]
Here we introduce a new structure, fiemap_cache, which records previous
fiemap extent.
And will always try to merge current fiemap_cache result before calling
fiemap_fill_next_extent().
Only when we failed to merge current fiemap extent with cached one, we
will call fiemap_fill_next_extent() to submit cached one.
So by this method, we can merge all fiemap extents.
It can also be done in fs/ioctl.c, however the problem is if
fieinfo->fi_extents_max == 0, we have no space to cache previous fiemap
extent.
So I choose to merge it in btrfs.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0804ed0ca ]
The Raspberry Pi startup stub files for multi-core BCM283X processors
make the secondary CPUs spin until the corresponding mailbox is
written. These stubs are loaded at physical address 0x00000xxx (as seen
by the ARMs), but this page will be reused by the kernel unless it is
explicitly reserved, causing the waiting cores to execute random code.
Use the /memreserve/ Device Tree directive to mark the first page as
off-limits to the kernel.
See: https://github.com/raspberrypi/linux/issues/1989
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7595a820b ]
Move NAPI enable to 'ath10k_ahb_hif_start' from
'ath10k_ahb_hif_power_up'. This is to maintain the symmetry
of calling napi_enable() from ath10k_ahb_hif_start() so that it
matches with napi_disable() being called from ath10k_pci_hif_stop().
This change is based on the crash fix from Kalle for PCI interface in
commit 1427228d58 ("ath10k: fix napi crash during rmmod when probe
firmware fails").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2dc9b6e38 ]
As a further improvement to the PF/VF link change logic, use a private
mutex instead of the rtnl lock to protect link change logic. With the
new mutex, we don't have to take the rtnl lock in the workqueue when
we have to handle link related functions. If the VF and PF drivers
are running on the same host and both take the rtnl lock and one is
waiting for the other, it will cause timeout. This patch fixes these
timeouts.
Fixes: 90c694bb71 ("bnxt_en: Fix RTNL lock usage on bnxt_update_link().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd849b7c41 ]
No matter whether a request is inserted into workqueue as a work item
to cancel a subscription or to delete a subscription's subscriber
asynchronously, the work items may be executed in different workers.
As a result, it doesn't mean that one request which is raised prior to
another request is definitely handled before the latter. By contrast,
if the latter request is executed before the former request, below
error may happen:
[ 656.183644] BUG: spinlock bad magic on CPU#0, kworker/u8:0/12117
[ 656.184487] general protection fault: 0000 [#1] SMP
[ 656.185160] Modules linked in: tipc ip6_udp_tunnel udp_tunnel 9pnet_virtio 9p 9pnet virtio_net virtio_pci virtio_ring virtio [last unloaded: ip6_udp_tunnel]
[ 656.187003] CPU: 0 PID: 12117 Comm: kworker/u8:0 Not tainted 4.11.0-rc7+ #6
[ 656.187920] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 656.188690] Workqueue: tipc_rcv tipc_recv_work [tipc]
[ 656.189371] task: ffff88003f5cec40 task.stack: ffffc90004448000
[ 656.190157] RIP: 0010:spin_bug+0xdd/0xf0
[ 656.190678] RSP: 0018:ffffc9000444bcb8 EFLAGS: 00010202
[ 656.191375] RAX: 0000000000000034 RBX: ffff88003f8d1388 RCX: 0000000000000000
[ 656.192321] RDX: ffff88003ba13708 RSI: ffff88003ba0cd08 RDI: ffff88003ba0cd08
[ 656.193265] RBP: ffffc9000444bcd0 R08: 0000000000000030 R09: 000000006b6b6b6b
[ 656.194208] R10: ffff8800bde3e000 R11: 00000000000001b4 R12: 6b6b6b6b6b6b6b6b
[ 656.195157] R13: ffffffff81a3ca64 R14: ffff88003f8d1388 R15: ffff88003f8d13a0
[ 656.196101] FS: 0000000000000000(0000) GS:ffff88003ba00000(0000) knlGS:0000000000000000
[ 656.197172] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 656.197935] CR2: 00007f0b3d2e6000 CR3: 000000003ef9e000 CR4: 00000000000006f0
[ 656.198873] Call Trace:
[ 656.199210] do_raw_spin_lock+0x66/0xa0
[ 656.199735] _raw_spin_lock_bh+0x19/0x20
[ 656.200258] tipc_subscrb_subscrp_delete+0x28/0xf0 [tipc]
[ 656.200990] tipc_subscrb_rcv_cb+0x45/0x260 [tipc]
[ 656.201632] tipc_receive_from_sock+0xaf/0x100 [tipc]
[ 656.202299] tipc_recv_work+0x2b/0x60 [tipc]
[ 656.202872] process_one_work+0x157/0x420
[ 656.203404] worker_thread+0x69/0x4c0
[ 656.203898] kthread+0x138/0x170
[ 656.204328] ? process_one_work+0x420/0x420
[ 656.204889] ? kthread_create_on_node+0x40/0x40
[ 656.205527] ret_from_fork+0x29/0x40
[ 656.206012] Code: 48 8b 0c 25 00 c5 00 00 48 c7 c7 f0 24 a3 81 48 81 c1 f0 05 00 00 65 8b 15 61 ef f5 7e e8 9a 4c 09 00 4d 85 e4 44 8b 4b 08 74 92 <45> 8b 84 24 40 04 00 00 49 8d 8c 24 f0 05 00 00 eb 8d 90 0f 1f
[ 656.208504] RIP: spin_bug+0xdd/0xf0 RSP: ffffc9000444bcb8
[ 656.209798] ---[ end trace e2a800e6eb0770be ]---
In above scenario, the request of deleting subscriber was performed
earlier than the request of canceling a subscription although the
latter was issued before the former, which means tipc_subscrb_delete()
was called before tipc_subscrp_cancel(). As a result, when
tipc_subscrb_subscrp_delete() called by tipc_subscrp_cancel() was
executed to cancel a subscription, the subscription's subscriber
refcnt had been decreased to 1. After tipc_subscrp_delete() where
the subscriber was freed because its refcnt was decremented to zero,
but the subscriber's lock had to be released, as a consequence, panic
happened.
By contrast, if we increase subscriber's refcnt before
tipc_subscrb_subscrp_delete() is called in tipc_subscrp_cancel(),
the panic issue can be avoided.
Fixes: d094c4d5f5 ("tipc: add subscription refcount to avoid invalid delete")
Reported-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c7e983b22 ]
In 9dbbfb0ab6 function tipc_sk_reinit
had additional logic added to loop in the event that function
rhashtable_walk_next() returned -EAGAIN. No worries.
However, if rhashtable_walk_start returns -EAGAIN, it does "continue",
and therefore skips the call to rhashtable_walk_stop(). That has
the effect of calling rcu_read_lock() without its paired call to
rcu_read_unlock(). Since rcu_read_lock() may be nested, the problem
may not be apparent for a while, especially since resize events may
be rare. But the comments to rhashtable_walk_start() state:
* ...Note that we take the RCU lock in all
* cases including when we return an error. So you must always call
* rhashtable_walk_stop to clean up.
This patch replaces the continue with a goto and label to ensure a
matching call to rhashtable_walk_stop().
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 061870800e ]
Completion on timeout should not free the driver command entry structure
as it will need to access it again once real completion event from FW
will occur.
Fixes: 73dd3a4839 ('net/mlx5: Avoid using pending command interface slots')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c78f7735b ]
Currently we create the sysfs entry even if we fail mapping
it. In that case, the unmapping will not remove the sysfs created
file. There is no good reason to create a sysfs entry for a non
working CMB and show his characteristics.
Fixes: f63572dff ("nvme: unmap CMB and remove sysfs file in reset path")
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07d432bb97 ]
The driver may sleep under a spin lock, and the function call path is:
post_one_send (acquire the lock by spin_lock_irqsave)
init_send_wqe
copy_from_user --> may sleep
There is no flow that makes "qp->is_user" true, and copy_from_user may
cause bug when a non-user pointer is used. So the lines of copy_from_user
and check of "qp->is_user" are removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f13e58767 ]
A previous patch which claimed to remove off by ones actually introduced
them.
strlen() returns the length of the string not including the NUL
character. We are using strcpy() to copy "name" into a buffer which is
ORANGEFS_MAX_XATTR_NAMELEN characters long. We should make sure to
leave space for the NUL, otherwise we're writing one character beyond
the end of the buffer.
Fixes: e675c5ec51 ("orangefs: clean up oversize xattr validation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5236333592 ]
RoCE Annex (A16.9.10/11) declares that during attach (detach) QP to a
multicast group, if the QP is associated with a RoCE port, the
multicast group MLID is unused and is ignored.
During attach or detach multicast, when the QP is associated with a
port, it is enough to check the port's link layer and validate the
LID only if it is Infiniband. Otherwise, avoid validating the
multicast LID.
Fixes: 8561eae60f ("IB/core: For multicast functions, verify that LIDs are multicast LIDs")
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14fa91e0fe ]
netdev_wait_allrefs() could rebroadcast NETDEV_UNREGISTER event
multiple times until all refs are gone, which will result in calling
ipoib_delete_debug_files multiple times and printing a warning.
Remove the WARN_ONCE since checks of NULL pointers before calling
debugfs_remove are not needed.
Fixes: 771a525840 ("IB/IPoIB: ibX: failed to create mcg debug file")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9ac89f5ad ]
The 98d610c373 patch was introduced since v4.11-rc1 that it causes
that the accelerometer input device will not be created on workable
machines because the HID string comparing logic is wrong.
And, the patch doesn't prevent that the accelerometer input device
be created on the machines that have no BST0001. That's because
the acpi_get_devices() returns success even it didn't find any
match device.
This patch fixed the HID string comparing logic of BST0001 device.
And, it also makes sure that the acpi_get_devices() returns
acpi_handle for BST0001.
Fixes: 98d610c373 ("acer-wmi: setup accelerometer when machine has appropriate notify event")
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=193761
Reported-by: Samuel Sieb <samuel-kbugs@sieb.net>
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b91d532928 ]
After commit c2ed1880fd ("net: ipv6: check route protocol when
deleting routes"), ipv6 route checks rt protocol when trying to
remove a rt entry.
It introduced a side effect causing 'ip -6 route flush cache' not
to work well. When flushing caches with iproute, all route caches
get dumped from kernel then removed one by one by sending DELROUTE
requests to kernel for each cache.
The thing is iproute sends the request with the cache whose proto
is set with RTPROT_REDIRECT by rt6_fill_node() when kernel dumps
it. But in kernel the rt_cache protocol is still 0, which causes
the cache not to be matched and removed.
So the real reason is rt6i_protocol in the route is not set when
it is allocated. As David Ahern's suggestion, this patch is to
set rt6i_protocol properly in the route when it is installed and
remove the codes setting rtm_protocol according to rt6i_flags in
rt6_fill_node.
This is also an improvement to keep rt6i_protocol consistent with
rtm_protocol.
Fixes: c2ed1880fd ("net: ipv6: check route protocol when deleting routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a16c8629 ]
PCI_STD_RESOURCE_END is (confusingly) the index of the last valid BAR, not
the *number* of BARs. To iterate through all possible BARs, we need to
include PCI_STD_RESOURCE_END.
Fixes: 55d728a40d ("efi/fb: Avoid reconfiguration of BAR that covers the framebuffer")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ababb08938 ]
Since commit e247454103 ("bcm2835: Fix hang for writing messages
larger than 16 bytes") the interrupt handler is prone to a possible
NULL pointer dereference. This could happen if an interrupt fires
before curr_msg is set by bcm2835_i2c_xfer_msg() and randomly occurs
on the RPi 3. Even this is an unexpected behavior the driver must
handle that with an error instead of a crash.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: e247454103 ("bcm2835: Fix hang for writing messages larger than 16 bytes")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deb8699932 ]
HiSilicon Hip06/Hip07 can operate as either a Root Port or an Endpoint. It
always advertises an MSI capability, but it can only generate MSIs when in
Endpoint mode.
The device has the same Vendor and Device IDs in both modes, so check the
Class Code and disable MSI only when operating as a Root Port.
[bhelgaas: changelog]
Fixes: 72f2ff0deb ("PCI: Disable MSI for HiSilicon Hip06/Hip07 Root Ports")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f27cff859 ]
The acpi_mask_gpe= kernel parameter documentation states that the range
of mask is 128 GPEs (0x00 to 0x7F). The acpi_masked_gpes mask is a u64 so
only 64 GPEs (0x00 to 0x3F) can really be masked.
Use a bitmap of size 0xFF instead of a u64 for the GPE mask so 256
GPEs can be masked.
Fixes: 9c4aa1eecb (ACPI / sysfs: Provide quirk mechanism to prevent GPE flooding)
Signed-off-by: Prarit Bharava <prarit@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a83fba6ca ]
This patch reverts two previous applied patches to fix an issue
that appeared when using SGMII based SFP modules. In the current
state the driver will try to reset the PHY before obtaining the
phy_addr of the SGMII attached PHY. That leads to an error in
e1000_write_phy_reg_sgmii_82575. Causing the initialization to
fail:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of ????:??:??.? failed with error -3
The patches being reverted are:
commit 1827853354
Author: Aaron Sierra <asierra@xes-inc.com>
Date: Tue Nov 29 10:03:56 2016 -0600
igb: reset the PHY before reading the PHY ID
commit 440aeca4b9
Author: Matwey V Kornilov <matwey@sai.msu.ru>
Date: Thu Nov 24 13:32:48 2016 +0300
igb: Explicitly select page 0 at initialization
The first reverted patch directly causes the problem mentioned above.
In case of SGMII the phy_addr is not known at this point and will
only be obtained by 'igb_get_phy_id_82575' further down in the code.
The second removed patch selects forces selection of page 0 in the
PHY. Something that the reset tries to address as well.
As pointed out by Alexander Duzck, the patch below fixes the same
issue but in the proper location:
commit 4e684f59d7
Author: Chris J Arges <christopherarges@gmail.com>
Date: Wed Nov 2 09:13:42 2016 -0500
igb: Workaround for igb i210 firmware issue
Reverts: 440aeca4b9.
Reverts: 1827853354.
Signed-off-by: Christian Grönke <c.groenke@infodas.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
