[ Upstream commit f596da3efa ]
When the blk_classic option is enabled, non-blktrace events must be
filtered out. Otherwise, events of other types are output in the blktrace
classic format, which is unexpected.
The problem can be triggered in the following ways:
# echo 1 > /sys/kernel/debug/tracing/options/blk_classic
# echo 1 > /sys/kernel/debug/tracing/events/enable
# echo blk > /sys/kernel/debug/tracing/current_tracer
# cat /sys/kernel/debug/tracing/trace_pipe
Fixes: c71a896154 ("blktrace: add ftrace plugin")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Link: https://lore.kernel.org/r/20221122040410.85113-1-yangjihong1@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76c16af2cb ]
The gen 2 chips RTL8192EU and RTL8188FU periodically send the driver
reports about the TX rate, and the driver passes these reports to
sta_statistics. The reports from RTL8192EU may or may not include the
channel width. The reports from RTL8188FU do not include it.
Only access the c2h->ra_report.bw field if the report (skb) is big
enough.
The other problem fixed here is that the code was actually never
changing the channel width initially reported by
rtl8xxxu_bss_info_changed because the value of RATE_INFO_BW_20 is 0.
Fixes: 0985d3a410 ("rtl8xxxu: Feed current txrate information for mac80211")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/5b41f1ae-72e7-6b7a-2459-b736399a1c40@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a6f994f84 ]
The addition of 3WIRE support would affect MOSI direction even
when still in standard (4 wire) mode. This can lead to MOSI being
at an invalid logic level when a device driver sets an SPI
message with a NULL tx_buf.
spi.h states that if tx_buf is NULL then "zeros will be shifted
out ... " If MOSI is tristated then the data shifted out is subject
to pull resistors, keepers, or in the absence of those, noise.
This issue came to light when using spi-gpio connected to an
ADS7843 touchscreen controller. MOSI pulled high when clocking
MISO data in caused the SPI device to interpret this as a command
which would put the device in an unexpected and non-functional
state.
Fixes: 4b859db2c6 ("spi: spi-gpio: add SPI_3WIRE support")
Fixes: 5132b3d283 ("spi: gpio: Support 3WIRE high-impedance turn-around")
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Link: https://lore.kernel.org/r/20221207230853.6174-1-kris@embeddedTS.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e5e5defdb ]
As the kmalloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others.
Fixes: cb1d3a3363 ("[media] coda: add CODA7541 JPEG support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b8082238f ]
As the coda_iram_alloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others.
Fixes: b313bcc9a4 ("[media] coda: simplify IRAM setup")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ff05a1ad ]
In configure_channels(), we should call of_node_put() when breaking
out of for_each_child_of_node() which will automatically increase
and decrease the refcount.
Fixes: c5f5d0f997 ("[media] c8sectpfe: STiH407/10 Linux DVB demux support")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38a20f29a ]
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
So fix this by checking the return value and goto error path which
will call mmc_free_host().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221109133539.3275664-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc5b9b50fc ]
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
So fix this by checking the return value and goto error path which
will call mmc_free_host(), besides, other resources also need be
released.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221109133237.3273558-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4e46fb61e ]
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
Fix this by checking the return value and goto error path which
will call mmc_free_host().
Fixes: f0bf7f61b8 ("mmc: Add new via-sdmmc host controller driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221108130949.1067699-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90935f16f2 ]
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
Fix this by checking the return value and goto error path which
will call mmc_free_host().
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221108123417.479045-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a525cad241 ]
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
Fix this by checking the return value and goto error path wihch
will call mmc_free_host().
Fixes: a45c6cb816 ("[ARM] 5369/1: omap mmc: Add new omap hsmmc controller for 2430 and 34xx, v3")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221108121316.340354-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e6e8c4372 ]
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
So fix this by checking the return value and calling mmc_free_host()
in the error path.
Fixes: 7d2be0749a ("atmel-mci: Driver for Atmel on-chip MMC controllers")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221108122819.429975-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29276d56f6 ]
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host(), besides, clk_disable_unprepare() also needs be called.
Fixes: 3a96dff0f8 ("mmc: SD/MMC Host Controller for Wondermedia WM8505/WM8650")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221101063023.1664968-10-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0613ad2401 ]
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host(), besides, the timer added before mmc_add_host() needs be del.
And this patch fixes another missing call mmc_free_host() if usb_control_msg()
fails.
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221101063023.1664968-9-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f670744a31 ]
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host(), besides, free_irq() also needs be called.
Fixes: a5eb8bbd66 ("mmc: add Toshiba PCI SD controller driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221101063023.1664968-8-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc38a5a10e ]
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and calling mmc_free_host() in the
error path, besides, led_classdev_unregister() and pm_runtime_disable() also
need be called.
Fixes: c7f6558d84 ("mmc: Add realtek USB sdmmc host driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221101063023.1664968-7-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80e1ef3afb ]
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host(), besides, ->exit() need be called to uninit the pdata.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221101063023.1664968-5-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cde600af7b ]
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host().
Fixes: d96be879ff ("mmc: Add a MX2/MX3 specific SDHC driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221101063023.1664968-4-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ca18d09c7 ]
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host().
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221101063023.1664968-3-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e93d1468f4 ]
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and calling mmc_free_host() in the
error path.
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221101063023.1664968-2-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4e4f66901 ]
If the state manager thread fails to start, then we should just mark the
client initialisation as failed so that other processes or threads don't
get stuck in nfs_wait_client_init_complete().
Reported-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Fixes: 4697bd5e94 ("NFSv4: Fix a race in the net namespace mount notification")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50fa355bc0 ]
socket dynamically created is not released when getting an unintended
address family type in rpc_sockname(), direct to out_release for calling
sock_release().
Fixes: 2e738fdce2 ("SUNRPC: Add API to acquire source address")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf2ea3c86a ]
I got a null-ptr-defer error report when I do the following tests
on the qemu platform:
make defconfig and CONFIG_PARPORT=m, CONFIG_PARPORT_PC=m,
CONFIG_SND_MTS64=m
Then making test scripts:
cat>test_mod1.sh<<EOF
modprobe snd-mts64
modprobe snd-mts64
EOF
Executing the script, perhaps several times, we will get a null-ptr-defer
report, as follow:
syzkaller:~# ./test_mod.sh
snd_mts64: probe of snd_mts64.0 failed with error -5
modprobe: ERROR: could not insert 'snd_mts64': No such device
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 0 PID: 205 Comm: modprobe Not tainted 6.1.0-rc8-00588-g76dcd734eca2 #6
Call Trace:
<IRQ>
snd_mts64_interrupt+0x24/0xa0 [snd_mts64]
parport_irq_handler+0x37/0x50 [parport]
__handle_irq_event_percpu+0x39/0x190
handle_irq_event_percpu+0xa/0x30
handle_irq_event+0x2f/0x50
handle_edge_irq+0x99/0x1b0
__common_interrupt+0x5d/0x100
common_interrupt+0xa0/0xc0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:_raw_write_unlock_irqrestore+0x11/0x30
parport_claim+0xbd/0x230 [parport]
snd_mts64_probe+0x14a/0x465 [snd_mts64]
platform_probe+0x3f/0xa0
really_probe+0x129/0x2c0
__driver_probe_device+0x6d/0xc0
driver_probe_device+0x1a/0xa0
__device_attach_driver+0x7a/0xb0
bus_for_each_drv+0x62/0xb0
__device_attach+0xe4/0x180
bus_probe_device+0x82/0xa0
device_add+0x550/0x920
platform_device_add+0x106/0x220
snd_mts64_attach+0x2e/0x80 [snd_mts64]
port_check+0x14/0x20 [parport]
bus_for_each_dev+0x6e/0xc0
__parport_register_driver+0x7c/0xb0 [parport]
snd_mts64_module_init+0x31/0x1000 [snd_mts64]
do_one_initcall+0x3c/0x1f0
do_init_module+0x46/0x1c6
load_module+0x1d8d/0x1e10
__do_sys_finit_module+0xa2/0xf0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 1 seconds..
The mts wa not initialized during interrupt, we add check for
mts to fix this bug.
Fixes: 68ab801e32 ("[ALSA] Add snd-mts64 driver for ESI Miditerminal 4140")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221206061004.1222966-1-cuigaosheng1@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 084ed144c4 ]
The JC42 compatible thermal sensor on Kingston KSM32ES8/16ME DIMMs
(using Micron E-Die) is an ST Microelectronics STTS2004 (manufacturer
0x104a, device 0x2201). It does not keep the previously programmed
minimum, maximum and critical temperatures after system suspend and
resume (which is a shutdown / startup cycle for the JC42 temperature
sensor). This results in an alarm on system resume because the hardware
default for these values is 0°C (so any environment temperature greater
than 0°C will trigger the alarm).
Example before system suspend:
jc42-i2c-0-1a
Adapter: SMBus PIIX4 adapter port 0 at 0b00
temp1: +34.8°C (low = +0.0°C)
(high = +85.0°C, hyst = +85.0°C)
(crit = +95.0°C, hyst = +95.0°C)
Example after system resume (without this change):
jc42-i2c-0-1a
Adapter: SMBus PIIX4 adapter port 0 at 0b00
temp1: +34.8°C (low = +0.0°C) ALARM (HIGH, CRIT)
(high = +0.0°C, hyst = +0.0°C)
(crit = +0.0°C, hyst = +0.0°C)
Apply the cached values from the JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER, JC42_REG_TEMP_CRITICAL and JC42_REG_SMBUS (where
the SMBUS register is not related to this issue but a side-effect of
using regcache_sync() during system resume with the previously
cached/programmed values. This fixes the alarm due to the hardware
defaults of 0°C because the previously applied limits (set by userspace)
are re-applied on system resume.
Fixes: 175c490c9e ("hwmon: (jc42) Add support for STTS2004 and AT30TSE004")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-3-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f2fa4726f ]
Switch the jc42 driver to use an I2C regmap to access the registers.
Also move over to regmap's built-in caching instead of adding a
custom caching implementation. This works for JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER and JC42_REG_TEMP_CRITICAL as these values never
change except when explicitly written. The cache For JC42_REG_TEMP is
dropped (regmap can't cache it because it's volatile, meaning it can
change at any time) as well for simplicity and consistency with other
drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-2-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stable-dep-of: 084ed144c4 ("hwmon: (jc42) Restore the min/max/critical temperatures on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c7aa13210 ]
hsr_register_frame_out() compares new sequence_nr vs the old one
recorded in hsr_node::seq_out and if the new sequence_nr is higher then
it will be written to hsr_node::seq_out as the new value.
This operation isn't locked so it is possible that two frames with the
same sequence number arrive (via the two slave devices) and are fed to
hsr_register_frame_out() at the same time. Both will pass the check and
update the sequence counter later to the same value. As a result the
content of the same packet is fed into the stack twice.
This was noticed by running ping and observing DUP being reported from
time to time.
Instead of using the hsr_priv::seqnr_lock for the whole receive path (as
it is for sending in the master node) add an additional lock that is only
used for sequence number checks and updates.
Add a per-node lock that is used during sequence number reads and
updates.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06afd2c31d ]
Sending frames via the hsr (master) device requires a sequence number
which is tracked in hsr_priv::sequence_nr and protected by
hsr_priv::seqnr_lock. Each time a new frame is sent, it will obtain a
new id and then send it via the slave devices.
Each time a packet is sent (via hsr_forward_do()) the sequence number is
checked via hsr_register_frame_out() to ensure that a frame is not
handled twice. This make sense for the receiving side to ensure that the
frame is not injected into the stack twice after it has been received
from both slave ports.
There is no locking to cover the sending path which means the following
scenario is possible:
CPU0 CPU1
hsr_dev_xmit(skb1) hsr_dev_xmit(skb2)
fill_frame_info() fill_frame_info()
hsr_fill_frame_info() hsr_fill_frame_info()
handle_std_frame() handle_std_frame()
skb1's sequence_nr = 1
skb2's sequence_nr = 2
hsr_forward_do() hsr_forward_do()
hsr_register_frame_out(, 2) // okay, send)
hsr_register_frame_out(, 1) // stop, lower seq duplicate
Both skbs (or their struct hsr_frame_info) received an unique id.
However since skb2 was sent before skb1, the higher sequence number was
recorded in hsr_register_frame_out() and the late arriving skb1 was
dropped and never sent.
This scenario has been observed in a three node HSR setup, with node1 +
node2 having ping and iperf running in parallel. From time to time ping
reported a missing packet. Based on tracing that missing ping packet did
not leave the system.
It might be possible (didn't check) to drop the sequence number check on
the sending side. But if the higher sequence number leaves on wire
before the lower does and the destination receives them in that order
and it will drop the packet with the lower sequence number and never
inject into the stack.
Therefore it seems the only way is to lock the whole path from obtaining
the sequence number and sending via dev_queue_xmit() and assuming the
packets leave on wire in the same order (and don't get reordered by the
NIC).
Cover the whole path for the master interface from obtaining the ID
until after it has been forwarded via hsr_forward_skb() to ensure the
skbs are sent to the NIC in the order of the assigned sequence numbers.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5c7652eb1 ]
The hsr device is a software device. Its
net_device_ops::ndo_start_xmit() routine will process the packet and
then pass the resulting skb to dev_queue_xmit().
During processing, hsr acquires a lock with spin_lock_bh()
(hsr_add_node()) which needs to be promoted to the _irq() suffix in
order to avoid a potential deadlock.
Then there are the warnings in dev_queue_xmit() (due to
local_bh_disable() with disabled interrupts) left.
Instead trying to address those (there is qdisc and…) for netpoll sake,
just disable netpoll on hsr.
Disable netpoll on hsr and replace the _irqsave() locking with _bh().
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78be9217c4 ]
For a switch to offload insertion of HSR/PRP tags, frames must not be
sent to the CPU facing switch port with a tag. Generate supervision frames
(eth type ETH_P_PRP) without HSR v1 (ETH_P_HSR)/PRP tag and rely on
create_tagged_frame which inserts it later. This will allow skipping the
tag insertion for all outgoing frames in the future which is required for
HSR v1/PRP tag insertions to be offloaded.
HSR v0 supervision frames always contain tag information so insertion of
the tag can't be offloaded. IEC 62439-3 Ed.2.0 (HSR v1) specifically
notes that this was changed since v0 to allow offloading.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d5c7652eb1 ("hsr: Disable netpoll.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aa2820177 ]
hsr_forward_skb() a skb and keeps information in an on-stack
hsr_frame_info. hsr_get_node() assigns hsr_frame_info::node_src which is
from a RCU list. This pointer is used later in hsr_forward_do().
I don't see a reason why this pointer can't vanish midway since there is
no guarantee that hsr_forward_skb() is invoked from an RCU read section.
Use rcu_read_lock() to protect hsr_frame_info::node_src from its
assignment until it is no longer used.
Fixes: f266a683a4 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03dd0d49de ]
Make sure the nss is valid for nss_delta array. Return zero
if the index is invalid.
Coverity message:
Event overrun-call: Overrunning callee's array of size 4 by passing
argument "n_chains" (which evaluates to 15) in call to
"mt76_tx_power_nss_delta".
int delta = mt76_tx_power_nss_delta(n_chains);
Fixes: 07cda40630 ("mt76: fix rounding issues on converting per-chain and combined txpower")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 833a9fd28c ]
In regulatory_init_db(), when it's going to return a error, reg_pdev
should be unregistered. When load_builtin_regdb_keys() fails it doesn't
do it and makes cfg80211 can't be reload with report:
sysfs: cannot create duplicate filename '/devices/platform/regulatory.0'
...
<TASK>
dump_stack_lvl+0x79/0x9b
sysfs_warn_dup.cold+0x1c/0x29
sysfs_create_dir_ns+0x22d/0x290
kobject_add_internal+0x247/0x800
kobject_add+0x135/0x1b0
device_add+0x389/0x1be0
platform_device_add+0x28f/0x790
platform_device_register_full+0x376/0x4b0
regulatory_init+0x9a/0x4b2 [cfg80211]
cfg80211_init+0x84/0x113 [cfg80211]
...
Fixes: 90a53e4432 ("cfg80211: implement regdb signature checking")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221109090237.214127-1-chenzhongjin@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dbfa445ff ]
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
has changed the user-space interface so that bogus SPI_CS_HIGH started
to appear in the mask returned by SPI_IOC_RD_MODE even for active-low CS
pins. Commit 138c9c32f0
("spi: spidev: Fix CS polarity if GPIO descriptors are used") fixed only
SPI_IOC_WR_MODE part of the problem. Let's fix SPI_IOC_RD_MODE
symmetrically.
Test case:
#include <sys/ioctl.h>
#include <fcntl.h>
#include <linux/spi/spidev.h>
int main(int argc, char **argv)
{
char modew = SPI_CPHA;
char moder;
int f = open("/dev/spidev0.0", O_RDWR);
if (f < 0)
return 1;
ioctl(f, SPI_IOC_WR_MODE, &modew);
ioctl(f, SPI_IOC_RD_MODE, &moder);
return moder == modew ? 0 : 2;
}
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20221130162927.539512-1-alexander.sverdlin@siemens.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a9841ca02 ]
In tcp_bpf_send_verdict() redirection, the eval variable is assigned to
__SK_REDIRECT after the apply_bytes data is sent, if msg has more_data,
sock_put() will be called multiple times.
We should reset the eval variable to __SK_NONE every time more_data
starts.
This causes:
IPv4: Attempt to release TCP socket in state 1 00000000b4c925d7
------------[ cut here ]------------
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 5 PID: 4482 at lib/refcount.c:25 refcount_warn_saturate+0x7d/0x110
Modules linked in:
CPU: 5 PID: 4482 Comm: sockhash_bypass Kdump: loaded Not tainted 6.0.0 #1
Hardware name: Red Hat KVM, BIOS 1.11.0-2.el7 04/01/2014
Call Trace:
<TASK>
__tcp_transmit_skb+0xa1b/0xb90
? __alloc_skb+0x8c/0x1a0
? __kmalloc_node_track_caller+0x184/0x320
tcp_write_xmit+0x22a/0x1110
__tcp_push_pending_frames+0x32/0xf0
do_tcp_sendpages+0x62d/0x640
tcp_bpf_push+0xae/0x2c0
tcp_bpf_sendmsg_redir+0x260/0x410
? preempt_count_add+0x70/0xa0
tcp_bpf_send_verdict+0x386/0x4b0
tcp_bpf_sendmsg+0x21b/0x3b0
sock_sendmsg+0x58/0x70
__sys_sendto+0xfa/0x170
? xfd_validate_state+0x1d/0x80
? switch_fpu_return+0x59/0xe0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: cd9733f5d7 ("tcp_bpf: Fix one concurrency problem in the tcp_bpf_send_verdict function")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1669718441-2654-2-git-send-email-yangpc@wangsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d7cfb48d8 ]
icmp conntrack will set icmp redirects as RELATED, but icmpv6 will not
do this.
For icmpv6, only icmp errors (code <= 128) are examined for RELATED state.
ICMPV6 Redirects are part of neighbour discovery mechanism, those are
handled by marking a selected subset (e.g. neighbour solicitations) as
UNTRACKED, but not REDIRECT -- they will thus be flagged as INVALID.
Add minimal support for REDIRECTs. No parsing of neighbour options is
added for simplicity, so this will only check that we have the embeeded
original header (ND_OPT_REDIRECT_HDR), and then attempt to do a flow
lookup for this tuple.
Also extend the existing test case to cover redirects.
Fixes: 9fb9cbb108 ("[NETFILTER]: Add nf_conntrack subsystem.")
Reported-by: Eric Garver <eric@garver.life>
Link: https://github.com/firewalld/firewalld/issues/1046
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Garver <eric@garver.life>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
