[ Upstream commit 93822f5161 ]
The bit flags in pmbus_driver_info functionality for YM-2151E chip were
joined with a comma operator instead of a bitwise OR. This means that
the last constant PMBUS_HAVE_IIN was not OR-ed with the other
PM_BUS_HAVE_* constants for this page but it initialized the next element
of the func array (which was not accessed from anywhere because of the
number of pages).
However, there is no need for setting PMBUS_HAVE_IIN in the 5Vsb page
because this command does not seem to be paged. Obviously, the device
only has one IIN sensor, so it doesn't make sense to query it again from
the second page.
Fixes: 1734b4135a ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Tomáš Pecka <tomas.pecka@cesnet.cz>
Link: https://lore.kernel.org/r/20230420171939.212040-1-tomas.pecka@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a68f9fa97 ]
As support for splitting transmission over several messages using
TX_DATA_CONT was introduced it does not immediately return the return
value of qcom_glink_tx().
The result is that in the intentless case (i.e. intent == NULL), the
code will continue to send all additional chunks. This is wasteful, and
it's possible that the send operation could incorrectly indicate
success, if the last chunk fits in the TX fifo.
Fix the condition.
Fixes: 8956927fae ("rpmsg: glink: Add TX_DATA_CONT command while sending")
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230418163018.785524-2-quic_bjorande@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44295af501 ]
cpufreq_verify_current_freq checks() if the frequency returned by
the hardware has a slight delta with the valid frequency value
last set and returns "policy->cur" if the delta is within "1 MHz".
In the comparison, "policy->cur" is in "kHz" but it's compared
against HZ_PER_MHZ. So, the comparison range becomes "1 GHz".
Fix this by comparing against KHZ_PER_MHZ instead of HZ_PER_MHZ.
Fixes: f55ae08c89 ("cpufreq: Avoid unnecessary frequency updates due to mismatch")
Signed-off-by: Sanjay Chandrashekara <sanjayc@nvidia.com>
[ sumit gupta: Commit message update ]
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faae443738 ]
Currently, acpi_device_remove_notify_handler() may return while the
notify handler being removed is still running which may allow the
module holding that handler to be torn down prematurely.
Address this issue by making acpi_device_remove_notify_handler() wait
for the handling of all the ACPI events in progress to complete before
returning.
Fixes: 5894b0c46e ("ACPI / scan: Move bus operations and notification routines to bus.c")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9523a0d81 ]
With HIGHRES enabled tick_sched_timer() is programmed every jiffy to
expire the timer_list timers. This timer is programmed accurate in
respect to CLOCK_MONOTONIC so that 0 seconds and nanoseconds is the
first tick and the next one is 1000/CONFIG_HZ ms later. For HZ=250 it is
every 4 ms and so based on the current time the next tick can be
computed.
This accuracy broke since the commit mentioned below because the jiffy
based clocksource is initialized with higher accuracy in
read_persistent_wall_and_boot_offset(). This higher accuracy is
inherited during the setup in tick_setup_device(). The timer still fires
every 4ms with HZ=250 but timer is no longer aligned with
CLOCK_MONOTONIC with 0 as it origin but has an offset in the us/ns part
of the timestamp. The offset differs with every boot and makes it
impossible for user land to align with the tick.
Align the tick period with CLOCK_MONOTONIC ensuring that it is always a
multiple of 1000/CONFIG_HZ ms.
Fixes: 857baa87b6 ("sched/clock: Enable sched clock early")
Reported-by: Gusenleitner Klaus <gus@keba.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/20230406095735.0_14edn3@linutronix.de
Link: https://lore.kernel.org/r/20230418122639.ikgfvu3f@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63a759694e ]
Statically initialized objects are usually not initialized via the init()
function of the subsystem. They are special cased and the subsystem
provides a function to validate whether an object which is not yet tracked
by debugobjects is statically initialized. This means the object is started
to be tracked on first use, e.g. activation.
This works perfectly fine, unless there are two concurrent operations on
that object. Schspa decoded the problem:
T0 T1
debug_object_assert_init(addr)
lock_hash_bucket()
obj = lookup_object(addr);
if (!obj) {
unlock_hash_bucket();
- > preemption
lock_subsytem_object(addr);
activate_object(addr)
lock_hash_bucket();
obj = lookup_object(addr);
if (!obj) {
unlock_hash_bucket();
if (is_static_object(addr))
init_and_track(addr);
lock_hash_bucket();
obj = lookup_object(addr);
obj->state = ACTIVATED;
unlock_hash_bucket();
subsys function modifies content of addr,
so static object detection does
not longer work.
unlock_subsytem_object(addr);
if (is_static_object(addr)) <- Fails
debugobject emits a warning and invokes the fixup function which
reinitializes the already active object in the worst case.
This race exists forever, but was never observed until mod_timer() got a
debug_object_assert_init() added which is outside of the timer base lock
held section right at the beginning of the function to cover the lockless
early exit points too.
Rework the code so that the lookup, the static object check and the
tracking object association happens atomically under the hash bucket
lock. This prevents the issue completely as all callers are serialized on
the hash bucket lock and therefore cannot observe inconsistent state.
Fixes: 3ac7fe5a4a ("infrastructure to debug (dynamic) objects")
Reported-by: syzbot+5093ba19745994288b53@syzkaller.appspotmail.com
Debugged-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://syzkaller.appspot.com/bug?id=22c8a5938eab640d1c6bcc0e3dc7be519d878462
Link: https://lore.kernel.org/lkml/20230303161906.831686-1-schspa@gmail.com
Link: https://lore.kernel.org/r/87zg7dzgao.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2a10b3801 ]
Need to disable decoder power when remove decoder hardware driver, adding
remove callback function in the definition of platform driver.
Fixes: c05bada35f ("media: mtk-vcodec: Add to support multi hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ad91e44e6 ]
When the "extra device ports" configuration was first added, the
additional mxp_device_port_connect_info registers were added around the
existing mxp_mesh_port_connect_info registers. What I missed about
CMN-700 is that it shuffled them around to remove this discontinuity.
As such, tweak the definitions and factor out a helper for reading these
registers so we can deal with this discrepancy easily, which does at
least allow nicely tidying up the callsites. With this we can then also
do the nice thing and skip accesses completely rather than relying on
RES0 behaviour where we know the extra registers aren't defined.
Fixes: 23760a0144 ("perf/arm-cmn: Add CMN-700 support")
Reported-by: Jing Zhang <renyu.zj@linux.alibaba.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/71d129241d4d7923cde72a0e5b4c8d2f6084525f.1681295193.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af6c0bd59f ]
Currently only the first attempt to single-step has any effect. After
that all further stepping remains "stuck" at the same program counter
value.
Refer to the ARM Architecture Reference Manual (ARM DDI 0487E.a) D2.12,
PSTATE.SS=1 should be set at each step before transferring the PE to the
'Active-not-pending' state. The problem here is PSTATE.SS=1 is not set
since the second single-step.
After the first single-step, the PE transferes to the 'Inactive' state,
with PSTATE.SS=0 and MDSCR.SS=1, thus PSTATE.SS won't be set to 1 due to
kernel_active_single_step()=true. Then the PE transferes to the
'Active-pending' state when ERET and returns to the debugger by step
exception.
Before this patch:
==================
Entering kdb (current=0xffff3376039f0000, pid 1) on processor 0 due to Keyboard Entry
[0]kdb>
[0]kdb>
[0]kdb> bp write_sysrq_trigger
Instruction(i) BP #0 at 0xffffa45c13d09290 (write_sysrq_trigger)
is enabled addr at ffffa45c13d09290, hardtype=0 installed=0
[0]kdb> go
$ echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to Breakpoint @ 0xffffad651a309290
[1]kdb> ss
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to SS trap @ 0xffffad651a309294
[1]kdb> ss
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to SS trap @ 0xffffad651a309294
[1]kdb>
After this patch:
=================
Entering kdb (current=0xffff6851c39f0000, pid 1) on processor 0 due to Keyboard Entry
[0]kdb> bp write_sysrq_trigger
Instruction(i) BP #0 at 0xffffc02d2dd09290 (write_sysrq_trigger)
is enabled addr at ffffc02d2dd09290, hardtype=0 installed=0
[0]kdb> go
$ echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to Breakpoint @ 0xffffc02d2dd09290
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd09294
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd09298
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd0929c
[1]kdb>
Fixes: 44679a4f14 ("arm64: KGDB: Add step debugging support")
Co-developed-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20230202073148.657746-3-sumit.garg@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5af507bef9 ]
arch_dynirq_lower_bound() is invoked by the core interrupt code to
retrieve the lowest possible Linux interrupt number for dynamically
allocated interrupts like MSI.
The x86 implementation uses this to exclude the IO/APIC GSI space.
This works correctly as long as there is an IO/APIC registered, but
returns 0 if not. This has been observed in VMs where the BIOS does
not advertise an IO/APIC.
0 is an invalid interrupt number except for the legacy timer interrupt
on x86. The return value is unchecked in the core code, so it ends up
to allocate interrupt number 0 which is subsequently considered to be
invalid by the caller, e.g. the MSI allocation code.
The function has already a check for 0 in the case that an IO/APIC is
registered, as ioapic_dynirq_base is 0 in case of device tree setups.
Consolidate this and zero check for both ioapic_dynirq_base and gsi_top,
which is used in the case that no IO/APIC is registered.
Fixes: 3e5bedc2c2 ("x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines")
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/1679988604-20308-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4a413e56d ]
Smatch reports:
drivers/regulator/stm32-pwr.c:166 stm32_pwr_regulator_probe() warn:
'base' from of_iomap() not released on lines: 151,166.
In stm32_pwr_regulator_probe(), base is not released
when devm_kzalloc() fails to allocate memory or
devm_regulator_register() fails to register a new regulator device,
which may cause a leak.
To fix this issue, replace of_iomap() with
devm_platform_ioremap_resource(). devm_platform_ioremap_resource()
is a specialized function for platform devices.
It allows 'base' to be automatically released whether the probe
function succeeds or fails.
Besides, use IS_ERR(base) instead of !base
as the return value of devm_platform_ioremap_resource()
can either be a pointer to the remapped memory or
an ERR_PTR() encoded error code if the operation fails.
Fixes: dc62f951a6 ("regulator: stm32-pwr: Fix return value check in stm32_pwr_regulator_probe()")
Signed-off-by: YAN SHI <m202071378@hust.edu.cn>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304111750.o2643eJN-lkp@intel.com/
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230412033529.18890-1-m202071378@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9d45ec74c ]
Commit 9593126dae ("media: venus: Add a handling of QC08C compressed
format") and commit cef92b14e6 ("media: venus: Add a handling of QC10C
compressed format") added support for the QC08C and QC10C compressed
formats respectively.
But these also caused a regression, because the new formats where added
at the beginning of the vdec_formats[] array and the vdec_inst_init()
function sets the default format output and capture using fixed indexes
of that array:
static void vdec_inst_init(struct venus_inst *inst)
{
...
inst->fmt_out = &vdec_formats[8];
inst->fmt_cap = &vdec_formats[0];
...
}
Since now V4L2_PIX_FMT_NV12 is not the first entry in the array anymore,
the default capture format is not set to that as it was done before.
Both commits changed the first index to keep inst->fmt_out default format
set to V4L2_PIX_FMT_H264, but did not update the latter to keep .fmt_out
default format set to V4L2_PIX_FMT_NV12.
Rather than updating the index to the current V4L2_PIX_FMT_NV12 position,
let's reorder the entries so that this format is the first entry again.
This would also make VIDIOC_ENUM_FMT report the V4L2_PIX_FMT_NV12 format
with an index 0 as it did before the QC08C and QC10C formats were added.
Fixes: 9593126dae ("media: venus: Add a handling of QC08C compressed format")
Fixes: cef92b14e6 ("media: venus: Add a handling of QC10C compressed format")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50248ad9f1 ]
The decoder driver should clear the last_buffer_dequeued flag of the
capture queue upon receiving V4L2_DEC_CMD_START.
The last_buffer_dequeued flag is set upon receiving EOS (which always
happens upon receiving V4L2_DEC_CMD_STOP).
Without this patch, after issuing the V4L2_DEC_CMD_STOP and
V4L2_DEC_CMD_START, the vb2_dqbuf() function will always fail, even if
the buffers are completed by the hardware.
Fixes: beac82904a ("media: venus: make decoder compliant with stateful codec API")
Signed-off-by: Michał Krawczyk <mk@semihalf.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c592f8ab1 ]
The driver was intended from the start to be a wake-up source for the
system, however due to the absence of a suitable call to
device_set_wakeup_capable(), the device_may_wakeup() call used to decide
whether to enable the GPIO interrupt as a wake-up source would never
happen. Lookup the DT standard "wakeup-source" property and call
device_init_wakeup() to ensure the device is flagged as being wakeup
capable.
Reported-by: Matthew Lear <matthew.lear@broadcom.com>
Fixes: fd0f6851eb ("[media] rc: Add support for GPIO based IR Receiver driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52f1783ff4 ]
The adev->dm.dc pointer can be NULL and dereferenced in amdgpu_dm_fini()
without checking.
Add a NULL pointer check before calling dc_dmub_srv_destroy().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 9a71c7d317 ("drm/amd/display: Register DMUB service with DC")
Signed-off-by: Igor Artemiev <Igor.A.Artemiev@mcst.ru>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2649c1a20e ]
hi846_init_controls doesn't clean the allocated ctrl_hdlr
in case there is a failure, which causes memleak. Add
v4l2_ctrl_handler_free to free the resource properly.
Fixes: e8c0882685 ("media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera")
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Reviewed-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5276c9df9c ]
When an async notifier is unregistered, the async sub-devices in the
notifier's done list will disappear with the notifier. However this is
currently also done to the sub-notifiers that remain registered. Their
sub-devices only need to be unbound while the async sub-devices themselves
need to be returned to the sub-notifier's waiting list. Do this now.
Fixes: 2cab00bb07 ("media: v4l: async: Allow binding notifiers to sub-devices")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30cf57da17 ]
In saa7134_initdev, it will call saa7134_hwinit1. There are three
function invoking here: saa7134_video_init1, saa7134_ts_init1
and saa7134_vbi_init1.
All of them will init a timer with same function. Take
saa7134_video_init1 as an example. It'll bound &dev->video_q.timeout
with saa7134_buffer_timeout.
In buffer_activate, the timer funtcion is started.
If we remove the module or device which will call saa7134_finidev
to make cleanup, there may be a unfinished work. The
possible sequence is as follows, which will cause a
typical UAF bug.
Fix it by canceling the timer works accordingly before cleanup in
saa7134_finidev.
CPU0 CPU1
|saa7134_buffer_timeout
saa7134_finidev |
kfree(dev); |
|
| saa7134_buffer_next
| //use dev
Fixes: 1e7126b4a8 ("media: saa7134: Convert timers to use timer_setup()")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5abda7a166 ]
In dm1105_probe, it called dm1105_ir_init and bound
&dm1105->ir.work with dm1105_emit_key.
When it handles IRQ request with dm1105_irq,
it may call schedule_work to start the work.
When we call dm1105_remove to remove the driver, there
may be a sequence as follows:
Fix it by finishing the work before cleanup in dm1105_remove
CPU0 CPU1
|dm1105_emit_key
dm1105_remove |
dm1105_ir_exit |
rc_unregister_device |
rc_free_device |
rc_dev_release |
kfree(dev); |
|
| rc_keydown
| //use
Fixes: 34d2f9bf18 ("V4L/DVB: dm1105: use dm1105_dev & dev instead of dm1105dvb")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aec8298c09 ]
The current SMN index used for the driver probe seems to be meant
for the BIOS pair and there are potential concurrency problems that can
occur with an inopportune SMI.
It is been advised to use SMN_INDEX_0 instead of SMN_INDEX_2, which is
what amd_nb.c provides and this function has protections to ensure that
only one caller can use it at a time.
Fixes: da5ce22df5 ("platform/x86/amd/pmf: Add support for PMF core layer")
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230406164807.50969-4-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3228cec23b ]
In rkvdec_probe, rkvdec->watchdog_work is bound with
rkvdec_watchdog_func. Then rkvdec_vp9_run may
be called to start the work.
If we remove the module which will call rkvdec_remove
to make cleanup, there may be a unfinished work.
The possible sequence is as follows, which will
cause a typical UAF bug.
Fix it by canceling the work before cleanup in rkvdec_remove.
CPU0 CPU1
|rkvdec_watchdog_func
rkvdec_remove |
rkvdec_v4l2_cleanup|
v4l2_m2m_release |
kfree(m2m_dev); |
|
| v4l2_m2m_get_curr_priv
| m2m_dev->curr_ctx //use
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50d0a7aea4 ]
In cedrus_probe, dev->watchdog_work is bound with cedrus_watchdog function.
In cedrus_device_run, it will started by schedule_delayed_work. If there is
an unfinished work in cedrus_remove, there may be a race condition and
trigger UAF bug.
CPU0 CPU1
|cedrus_watchdog
cedrus_remove |
v4l2_m2m_release |
kfree(m2m_dev) |
|
| v4l2_m2m_get_curr_priv
| m2m_dev //use
Fix it by canceling the worker in cedrus_remove.
Fixes: 7c38a551bd ("media: cedrus: Add watchdog for job completion")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e0ef56d81 ]
Putting core work to work queue using queue_work maybe fail, call
queue_work again when the count of core work in work queue is less
than core_list_cnt, making sure all the buffer in core list can be
scheduled.
Fixes: 365e4ba01d ("media: mtk-vcodec: Add work queue for core hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cfca6c1bf ]
Current instance will decode done when begin to wait lat buf full,
move the lat_buf of current instance to the top of core list to make
sure current instance's lat_buf will be used firstly.
Fixes: 365e4ba01d ("media: mtk-vcodec: Add work queue for core hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68c7df5276 ]
While the decoder can produce frames in both MM21 and MT21C formats, only
MM21 is currently supported by userspace tools (like gstreamer and libyuv).
In order to ensure userspace keeps working after the SCP firmware is
updated to support both MM21 and MT21C formats, force the MM21 format for
the capture queue.
This is meant as a stopgap solution while dynamic format switching between
MM21 and MT21C isn't implemented in the driver.
Fixes: 7501edef6b ("media: mediatek: vcodec: Different codec using different capture format")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nicolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d020d81b9 ]
Given that only the MM21 capture format is supported by userspace tools
(like gstreamer and libyuv), make it the default capture format.
This allows us to force the MM21 format even when a MM21 and MT21C capable
firmware is available (which is needed while dynamic format switching isn't
implemented in the driver), without causing the following regressions on
v4l2-compliance:
fail: v4l2-test-formats.cpp(478): pixelformat 3132544d (MT21) for buftype 9 not reported by ENUM_FMT
test VIDIOC_G_FMT: FAIL
fail: v4l2-test-formats.cpp(478): pixelformat 3132544d (MT21) for buftype 9 not reported by ENUM_FMT
test VIDIOC_TRY_FMT: FAIL
fail: v4l2-test-formats.cpp(478): pixelformat 3132544d (MT21) for buftype 9 not reported by ENUM_FMT
test VIDIOC_S_FMT: FAIL
Fixes: 7501edef6b ("media: mediatek: vcodec: Different codec using different capture format")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nicolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25528e1db ]
After commit b018be06f3 ("media: mediatek: vcodec: Read max resolution
from dec_capability"), the stateful video decoder driver never really
sets its output frame size to 4K.
Parse the decoder capability reported by the firmware, and update the
output frame size in mtk_init_vdec_params to enable 4K frame size when
available.
Fixes: b018be06f3 ("media: mediatek: vcodec: Read max resolution from dec_capability")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f96fb2df3e ]
The detection of atomic update failure in reserve_eilvt_offset() is
not correct. The value returned by atomic_cmpxchg() should be compared
to the old value from the location to be updated.
If these two are the same, then atomic update succeeded and
"eilvt_offsets[offset]" location is updated to "new" in an atomic way.
Otherwise, the atomic update failed and it should be retried with the
value from "eilvt_offsets[offset]" - exactly what atomic_try_cmpxchg()
does in a correct and more optimal way.
Fixes: a68c439b19 ("apic, x86: Check if EILVT APIC registers are available (AMD only)")
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230227160917.107820-1-ubizjak@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cba6cfdc7c ]
An automated bot told me that there was a potential lockdep problem
with regulators. This was on the chromeos-5.15 kernel, but I see
nothing that would be different downstream compared to upstream. The
bot said:
============================================
WARNING: possible recursive locking detected
5.15.104-lockdep-17461-gc1e499ed6604 #1 Not tainted
--------------------------------------------
kworker/u16:4/115 is trying to acquire lock:
ffffff8083110170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: create_regulator+0x398/0x7ec
but task is already holding lock:
ffffff808378e170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: ww_mutex_trylock+0x3c/0x7b8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(regulator_ww_class_mutex);
lock(regulator_ww_class_mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u16:4/115:
#0: ffffff808006a948 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x520/0x1348
#1: ffffffc00e0a7cc0 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x55c/0x1348
#2: ffffff80828a2260 (&dev->mutex){....}-{3:3}, at: __device_attach_async_helper+0xd0/0x2a4
#3: ffffff808378e170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: ww_mutex_trylock+0x3c/0x7b8
stack backtrace:
CPU: 2 PID: 115 Comm: kworker/u16:4 Not tainted 5.15.104-lockdep-17461-gc1e499ed6604 #1 9292e52fa83c0e23762b2b3aa1bacf5787a4d5da
Hardware name: Google Quackingstick (rev0+) (DT)
Workqueue: events_unbound async_run_entry_fn
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
dump_stack+0x1c/0x48
__lock_acquire+0x16d4/0x6c74
lock_acquire+0x208/0x750
__mutex_lock_common+0x11c/0x11f8
ww_mutex_lock+0xc0/0x440
create_regulator+0x398/0x7ec
regulator_resolve_supply+0x654/0x7c4
regulator_register_resolve_supply+0x30/0x120
class_for_each_device+0x1b8/0x230
regulator_register+0x17a4/0x1f40
devm_regulator_register+0x60/0xd0
reg_fixed_voltage_probe+0x728/0xaec
platform_probe+0x150/0x1c8
really_probe+0x274/0xa20
__driver_probe_device+0x1dc/0x3f4
driver_probe_device+0x78/0x1c0
__device_attach_driver+0x1ac/0x2c8
bus_for_each_drv+0x11c/0x190
__device_attach_async_helper+0x1e4/0x2a4
async_run_entry_fn+0xa0/0x3ac
process_one_work+0x638/0x1348
worker_thread+0x4a8/0x9c4
kthread+0x2e4/0x3a0
ret_from_fork+0x10/0x20
The problem was first reported soon after we made many of the
regulators probe asynchronously, though nothing I've seen implies that
the problems couldn't have also happened even without that.
I haven't personally been able to reproduce the lockdep issue, but the
issue does look somewhat legitimate. Specifically, it looks like in
regulator_resolve_supply() we are holding a "rdev" lock while calling
set_supply() -> create_regulator() which grabs the lock of a
_different_ "rdev" (the one for our supply). This is not necessarily
safe from a lockdep perspective since there is no documented ordering
between these two locks.
In reality, we should always be locking a regulator before the
supplying regulator, so I don't expect there to be any real deadlocks
in practice. However, the regulator framework in general doesn't
express this to lockdep.
Let's fix the issue by simply grabbing the two locks involved in the
same way we grab multiple locks elsewhere in the regulator framework:
using the "wound/wait" mechanisms.
Fixes: eaa7995c52 ("regulator: core: avoid regulator_resolve_supply() race condition")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230329143317.RFC.v2.2.I30d8e1ca10cfbe5403884cdd192253a2e063eb9e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b83a1772be ]
When a codepath locks a rdev using ww_mutex_lock_slow() directly then
that codepath is responsible for incrementing the "ref_cnt" and also
setting the "mutex_owner" to "current".
The regulator core consistently got that right for "ref_cnt" but
didn't always get it right for "mutex_owner". Let's fix this.
It's unlikely that this truly matters because the "mutex_owner" is
only needed if we're going to do subsequent locking of the same
rdev. However, even though it's not truly needed it seems less
surprising if we consistently set "mutex_owner" properly.
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230329143317.RFC.v2.1.I4e9d433ea26360c06dd1381d091c82bb1a4ce843@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
