commit 83e37e0bdd upstream.
The starting of AP interface can fail due to invalid
beacon interval, which does not match the minimum gcd
requirement set by the wifi driver. In such case, the
beacon interval of that interface gets updated with
that invalid beacon interval.
The next time that interface is brought up in AP mode,
an interface combination check is performed and the
beacon interval is taken from the previously set value.
In a case where an invalid beacon interval, i.e. a beacon
interval value which does not satisfy the minimum gcd criteria
set by the driver, is set, all the subsequent trials to
bring that interface in AP mode will fail, even if the
subsequent trials have a valid beacon interval.
To avoid this, in case of a failure in bringing up an
interface in AP mode due to interface combination error,
the interface beacon interval which is stored in bss
conf, needs to be restored with the last working value
of beacon interval.
Tested on ath10k using WCN3990.
Cc: stable@vger.kernel.org
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13443154f6 upstream.
The function prototype used to call JITed eBPF code (ie. the type of the
struct bpf_prog bpf_func field) returns an unsigned int. The MIPS n64
ABI that MIPS64 kernels target defines that 32 bit integers should
always be sign extended when passed in registers as either arguments or
return values.
This means that when returning any value which may not already be sign
extended (ie. of type REG_64BIT or REG_32BIT_ZERO_EX) we need to perform
that sign extension in order to comply with the n64 ABI. Without this we
see strange looking test failures from test_bpf.ko, such as:
test_bpf: #65 ALU64_MOV_X:
dst = 4294967295 jited:1 ret -1 != -1 FAIL (1 times)
Although the return value printed matches the expected value, this is
only because printf is only examining the least significant 32 bits of
the 64 bit register value we returned. The register holding the expected
value is sign extended whilst the v0 register was set to a zero extended
value by our JITed code, so when compared by a conditional branch
instruction the values are not equal.
We already handle this when the return value register is of type
REG_32BIT_ZERO_EX, so simply extend this to also cover REG_64BIT.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6bd53f9c4 ("MIPS: Add missing file for eBPF JIT.")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e7382153f upstream.
The following commit
441dae8f2f ("tracing: Add support for display of tgid in trace output")
removed the call to print_event_info() from print_func_help_header_irq()
which results in the ftrace header not reporting the number of entries
written in the buffer. As this wasn't the original intent of the patch,
re-introduce the call to print_event_info() to restore the orginal
behaviour.
Link: http://lkml.kernel.org/r/20190214152950.4179-1-quentin.perret@arm.com
Acked-by: Joel Fernandes <joelaf@google.com>
Cc: stable@vger.kernel.org
Fixes: 441dae8f2f ("tracing: Add support for display of tgid in trace output")
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4c07b4d6f upstream.
The generic ASN.1 decoder infrastructure doesn't guarantee that callbacks
will get as much data as they expect; callbacks have to check the `datalen`
parameter before looking at `data`. Make sure that snmp_version() and
snmp_helper() don't read/write beyond the end of the packet data.
(Also move the assignment to `pdata` down below the check to make it clear
that it isn't necessarily a pointer we can use before the `datalen` check.)
Fixes: cc2d58634e ("netfilter: nf_nat_snmp_basic: use asn1 decoder library")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7afe6c1d4 upstream.
While trying to reproduce a reported kernel panic on arm64, I discovered
that AUTH_GSS basically doesn't work at all with older enctypes on arm64
systems with CONFIG_VMAP_STACK enabled. It turns out there still a few
places using stack memory with scatterlists, causing krb5_encrypt() and
krb5_decrypt() to produce incorrect results (or a BUG if CONFIG_DEBUG_SG
is enabled).
Tested with cthon on v4.0/v4.1/v4.2 with krb5/krb5i/krb5p using
des3-cbc-sha1 and arcfour-hmac-md5.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2fd6e8191 upstream.
The disable_acs_redir parameter stores a pointer to the string passed to
pci_setup(). However, the string passed to PCI setup is actually a
temporary copy allocated in static __initdata memory. After init, once the
memory is freed, it is no longer valid to reference this pointer.
This bug was noticed in v5.0-rc1 after a change in commit c5eb119007
("PCI / PM: Allow runtime PM without callback functions") caused
pci_disable_acs_redir() to be called during shutdown which manifested
as an unable to handle kernel paging request at:
RIP: 0010:pci_enable_acs+0x3f/0x1e0
Call Trace:
pci_restore_state.part.44+0x159/0x3c0
pci_restore_standard_config+0x33/0x40
pci_pm_runtime_resume+0x2b/0xd0
? pci_restore_standard_config+0x40/0x40
__rpm_callback+0xbc/0x1b0
rpm_callback+0x1f/0x70
? pci_restore_standard_config+0x40/0x40
rpm_resume+0x4f9/0x710
? pci_conf1_read+0xb6/0xf0
? pci_conf1_write+0xb2/0xe0
__pm_runtime_resume+0x47/0x70
pci_device_shutdown+0x1e/0x60
device_shutdown+0x14a/0x1f0
kernel_restart+0xe/0x50
__do_sys_reboot+0x1ee/0x210
? __fput+0x144/0x1d0
do_writev+0x5e/0xf0
? do_writev+0x5e/0xf0
do_syscall_64+0x48/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
It was also likely possible to trigger this bug when hotplugging PCI
devices.
To fix this, instead of storing a pointer, we use kstrdup() to copy the
disable_acs_redir_param to its own buffer which will never be freed.
Fixes: aaca43fda7 ("PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support")
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83e418a805 upstream.
Commit bb36489032 ("mmc: meson-gx: Free irq in release() callback")
changed the _probe code to use request_threaded_irq() instead of
devm_request_threaded_irq().
Unfortunately this removes a fallback for the interrupt name:
devm_request_threaded_irq() uses the device name as fallback if the
given IRQ name is NULL. request_threaded_irq() has no such fallback,
thus /proc/interrupts shows "(null)" instead.
Explicitly pass the dev_name() so we get the IRQ name shown in
/proc/interrupts again.
While here, also fix the indentation of the request_threaded_irq()
parameter list.
Fixes: bb36489032 ("mmc: meson-gx: Free irq in release() callback")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b2db98e81 upstream.
memory allocated by kmem_cache_alloc() should be freed using
kmem_cache_free(), not kfree().
Fixes: ad669505c4 ("scsi: target/core: Make sure that target_wait_for_sess_cmds() waits long enough")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07bd14ccc3 upstream.
Add the missing unlock before return from function set_fan_div()
in the error handling case.
Fixes: c9c6391551 ("hwmon: (lm80) fix a missing check of the status of SMBus read")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3bed3cc415 ]
This patch addresses the fact that there are drivers, specifically tun,
that will call into the network page fragment allocators with buffer sizes
that are not cache aligned. Doing this could result in data alignment
and DMA performance issues as these fragment pools are also shared with the
skb allocator and any other devices that will use napi_alloc_frags or
netdev_alloc_frags.
Fixes: ffde7328a3 ("net: Split netdev_alloc_frag into __alloc_page_frag and add __napi_alloc_frag")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04c03114be ]
soukjin bae reported a crash in tcp_v4_err() handling
ICMP_DEST_UNREACH after tcp_write_queue_head(sk)
returned a NULL pointer.
Current logic should have prevented this :
if (seq != tp->snd_una || !icsk->icsk_retransmits ||
!icsk->icsk_backoff || fastopen)
break;
Problem is the write queue might have been purged
and icsk_backoff has not been cleared.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: soukjin bae <soukjin.bae@samsung.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4179cb5a4c ]
netif_rx() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Note this patch also fixes a small issue that came
with commit ce6502a8f9 ("vxlan: fix a use after free
in vxlan_encap_bypass"), since the dev->stats.rx_dropped
change was done on the wrong device.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Fixes: ce6502a8f9 ("vxlan: fix a use after free in vxlan_encap_bypass")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petr Machata <petrm@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225d946426 ]
In the unlikely event that the kmalloc call in vmci_transport_socket_init()
fails, we end-up calling vmci_transport_destruct() with a NULL vmci_trans()
and oopsing.
This change addresses the above explicitly checking for zero vmci_trans()
at destruction time.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 816db76635 ]
When fail, translate_desc() returns negative value, otherwise the
number of iovs. So we should fail when the return value is negative
instead of a blindly check against zero.
Detected by CoverityScan, CID# 1442593: Control flow issues (DEADCODE)
Fixes: cc5e710759 ("vhost: log dirty page correctly")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 224babd62d6f19581757a6d8bae3bf9501fc10de ]
GMAC IP is little-endian and used on several kind of CPU (big or little
endian). Main callbacks functions of the stmmac drivers take care about
it. It was not the case for dwmac4_get_timestamp function.
Fixes: ba1ffd74df ("stmmac: fix PTP support for GMAC4")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a7493e58a ]
We are saving the status of EEE even before we try to enable it. This
leads to a race with XMIT function that tries to arm EEE timer before we
set it up.
Fix this by only saving the EEE parameters after all operations are
performed with success.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 197f9ab7f0 ]
Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.
With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.
Fixes: f411a6160b ("net: phy: Add gmiitorgmii converter support")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c09551c6ff ]
According to the algorithm described in the comment block at the
beginning of ip_rt_send_redirect, the host should try to send
'ip_rt_redirect_number' ICMP redirect packets with an exponential
backoff and then stop sending them at all assuming that the destination
ignores redirects.
If the device has previously sent some ICMP error packets that are
rate-limited (e.g TTL expired) and continues to receive traffic,
the redirect packets will never be transmitted. This happens since
peer->rate_tokens will be typically greater than 'ip_rt_redirect_number'
and so it will never be reset even if the redirect silence timeout
(ip_rt_redirect_silence) has elapsed without receiving any packet
requiring redirects.
Fix it by using a dedicated counter for the number of ICMP redirect
packets that has been sent by the host
I have not been able to identify a given commit that introduced the
issue since ip_rt_send_redirect implements the same rate-limiting
algorithm from commit 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4974d5f678 ]
After commit c706863bc8 ("net: ip6_gre: always reports o_key to
userspace"), ip6gre and ip6gretap tunnels started reporting TUNNEL_KEY
output flag even if it is not configured.
ip6gre_fill_info checks erspan_ver value to add TUNNEL_KEY for
erspan tunnels, however in commit 84581bdae9 ("erspan: set
erspan_ver to 1 by default when adding an erspan dev")
erspan_ver is initialized to 1 even for ip6gre or ip6gretap
Fix the issue moving erspan_ver initialization in a dedicated routine
Fixes: c706863bc8 ("net: ip6_gre: always reports o_key to userspace")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e75913c93f ]
Follow those steps:
# ip addr add 2001:123::1/32 dev eth0
# ip addr add 2001:123:456::2/64 dev eth0
# ip addr del 2001:123::1/32 dev eth0
# ip addr del 2001:123:456::2/64 dev eth0
and then prefix route of 2001:123::1/32 will still exist.
This is because ipv6_prefix_equal in check_cleanup_prefix_route
func does not check whether two IPv6 addresses have the same
prefix length. If the prefix of one address starts with another
shorter address prefix, even though their prefix lengths are
different, the return value of ipv6_prefix_equal is true.
Here I add a check of whether two addresses have the same prefix
to decide whether their prefixes are equal.
Fixes: 5b84efecb7 ("ipv6 addrconf: don't cleanup prefix route for IFA_F_NOPREFIXROUTE")
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b89ea9c59 ]
The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).
This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 289460404f ]
The function-local variable "delay" enters the loop interpreted as delay
in bits. However, inside the loop it gets overwritten by the result of
mlxsw_sp_pg_buf_delay_get(), and thus leaves the loop as quantity in
cells. Thus on second and further loop iterations, the headroom for a
given priority is configured with a wrong size.
Fix by introducing a loop-local variable, delay_cells. Rename thres to
thres_cells for consistency.
Fixes: f417f04da5 ("mlxsw: spectrum: Refactor port buffer configuration")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c0db24cc4 ]
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88a8121dc1 ]
Since commit cb9f1b7838, scapy (which uses an AF_PACKET socket in
SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel:
Here is a example of the setup:
$ ip link set ntfp2 up
$ ip addr add 10.125.0.1/24 dev ntfp2
$ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2
$ ip addr add fd00:cafe:cafe::1/128 dev tun1
$ ip link set dev tun1 up
$ ip route add fd00:200::/64 dev tun1
$ scapy
>>> p = []
>>> p += IPv6(src='fd00:100::1', dst='fd00:200::1')/ICMPv6EchoRequest()
>>> send(p, count=1, inter=0.1)
>>> quit()
$ ip -s link ls dev tun1 | grep -A1 "TX.*errors"
TX: bytes packets errors dropped carrier collsns
0 0 1 0 0 0
The problem is that the network offset is set to the hard_header_len of the
output device (tun1, ie 14 + 20) and in our case, because the packet is
small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes
(ipv6 header) starting from the network offset).
This problem is more generally related to device with variable hard header
length. To avoid a too intrusive patch in the current release, a (ugly)
workaround is proposed in this patch. It has to be cleaned up in net-next.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1
Link: http://patchwork.ozlabs.org/patch/1024489/
Fixes: cb9f1b7838 ("ip: validate header length on virtual device xmit")
CC: Willem de Bruijn <willemb@google.com>
CC: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8a8fedd57 upstream.
When resuming, we check whether or not any previously connected
MST topologies are still present and if so, attempt to resume them. If
this fails, we disable said MST topologies and fire off a hotplug event
so that userspace knows to reprobe.
However, sending a hotplug event involves calling
drm_fb_helper_hotplug_event(), which in turn results in fbcon doing a
connector reprobe in the caller's thread - something we can't do at the
point in which i915 calls drm_dp_mst_topology_mgr_resume() since
hotplugging hasn't been fully initialized yet.
This currently causes some rather subtle but fatal issues. For example,
on my T480s the laptop dock connected to it usually disappears during a
suspend cycle, and comes back up a short while after the system has been
resumed. This guarantees pretty much every suspend and resume cycle,
drm_dp_mst_topology_mgr_set_mst(mgr, false); will be caused and in turn,
a connector hotplug will occur. Now it's Rute Goldberg time: when the
connector hotplug occurs, i915 reprobes /all/ of the connectors,
including eDP. However, eDP probing requires that we power on the panel
VDD which in turn, grabs a wakeref to the appropriate power domain on
the GPU (on my T480s, this is the PORT_DDI_A_IO domain). This is where
things start breaking, since this all happens before
intel_power_domains_enable() is called we end up leaking the wakeref
that was acquired and never releasing it later. Come next suspend/resume
cycle, this causes us to fail to shut down the GPU properly, which
causes it not to resume properly and die a horrible complicated death.
(as a note: this only happens when there's both an eDP panel and MST
topology connected which is removed mid-suspend. One or the other seems
to always be OK).
We could try to fix the VDD wakeref leak, but this doesn't seem like
it's worth it at all since we aren't able to handle hotplug detection
while resuming anyway. So, let's go with a more robust solution inspired
by nouveau: block fbdev from handling hotplug events until we resume
fbdev. This allows us to still send sysfs hotplug events to be handled
later by user space while we're resuming, while also preventing us from
actually processing any hotplug events we receive until it's safe.
This fixes the wakeref leak observed on the T480s and as such, also
fixes suspend/resume with MST topologies connected on this machine.
Changes since v2:
* Don't call drm_fb_helper_hotplug_event() under lock, do it after lock
(Chris Wilson)
* Don't call drm_fb_helper_hotplug_event() in
intel_fbdev_output_poll_changed() under lock (Chris Wilson)
* Always set ifbdev->hpd_waiting (Chris Wilson)
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 0e32b39cee ("drm/i915: add DP 1.2 MST support (v0.7)")
Cc: Todd Previte <tprevite@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129191001.442-2-lyude@redhat.com
(cherry picked from commit fe5ec65668)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69ef943dbc upstream.
Passing an object_count of sufficient size will make
object_count * 4 wrap around to be very small, then a later function
will happily iterate off the end of the object_ids array. Using
array_size() will saturate at SIZE_MAX, the kmalloc() will fail and
we'll return an -ENOMEM to the norty userspace.
Fixes: 62884cd386 ("drm: Add four ioctls for managing drm mode object leases [v7]")
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ae280b4ee upstream.
When provisioning a new data block for a virtual block, either because
the block was previously unallocated or because we are breaking sharing,
if the whole block of data is being overwritten the bio that triggered
the provisioning is issued immediately, skipping copying or zeroing of
the data block.
When this bio completes the new mapping is inserted in to the pool's
metadata by process_prepared_mapping(), where the bio completion is
signaled to the upper layers.
This completion is signaled without first committing the metadata. If
the bio in question has the REQ_FUA flag set and the system crashes
right after its completion and before the next metadata commit, then the
write is lost despite the REQ_FUA flag requiring that I/O completion for
this request must only be signaled after the data has been committed to
non-volatile storage.
Fix this by deferring the completion of overwrite bios, with the REQ_FUA
flag set, until after the metadata has been committed.
Cc: stable@vger.kernel.org
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0c129d3b upstream.
bio_sectors() returns the value in the units of 512-byte sectors (no
matter what the real sector size of the device). dm-crypt multiplies
bio_sectors() by on_disk_tag_size to calculate the space allocated for
integrity tags. If dm-crypt is running with sector size larger than
512b, it allocates more data than is needed.
Device Mapper trims the extra space when passing the bio to
dm-integrity, so this bug didn't result in any visible misbehavior.
But it must be fixed to avoid wasteful memory allocation for the block
integrity payload.
Fixes: ef43aa3806 ("dm crypt: add cryptographic data integrity protection (authenticated encryption)")
Cc: stable@vger.kernel.org # 4.12+
Reported-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfcc34c99f upstream.
sync_request_write no longer submits writes to a Faulty device. This has
the unfortunate side effect that bitmap bits can be incorrectly cleared
if a recovery is interrupted (previously, end_sync_write would have
prevented this). This means the next recovery may not copy everything
it should, potentially corrupting data.
Add a function for doing the proper md_bitmap_end_sync, called from
end_sync_write and the Faulty case in sync_request_write.
backport note to 4.14: s/md_bitmap_end_sync/bitmap_end_sync
Cc: stable@vger.kernel.org 4.14+
Fixes: 0c9d5b127f ("md/raid1: avoid reusing a resync bio after error handling.")
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Tested-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf43a757fd upstream.
In the middle of do_exit() there is there is a call
"ptrace_event(PTRACE_EVENT_EXIT, code);" That call places the process
in TACKED_TRACED aka "(TASK_WAKEKILL | __TASK_TRACED)" and waits for
for the debugger to release the task or SIGKILL to be delivered.
Skipping past dequeue_signal when we know a fatal signal has already
been delivered resulted in SIGKILL remaining pending and
TIF_SIGPENDING remaining set. This in turn caused the
scheduler to not sleep in PTACE_EVENT_EXIT as it figured
a fatal signal was pending. This also caused ptrace_freeze_traced
in ptrace_check_attach to fail because it left a per thread
SIGKILL pending which is what fatal_signal_pending tests for.
This difference in signal state caused strace to report
strace: Exit of unknown pid NNNNN ignored
Therefore update the signal handling state like dequeue_signal
would when removing a per thread SIGKILL, by removing SIGKILL
from the per thread signal mask and clearing TIF_SIGPENDING.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Ivan Delalande <colona@arista.com>
Cc: stable@vger.kernel.org
Fixes: 35634ffa17 ("signal: Always notice exiting tasks")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4a056987c upstream.
The problem is that the default for MQ is not to gather entropy, whereas
the default for the legacy queue was always to gather it. The original
attempt to fix entropy gathering for rotational disks under MQ added an
else branch in sd_read_block_characteristics(). Unfortunately, the entire
check isn't reached if the device has no characteristics VPD page. Since
this page was only introduced in SBC-3 and its optional anyway, most less
expensive rotational disks don't have one, meaning they all stopped
gathering entropy when we made MQ the default. In a wholly unrelated
change, openssl and openssh won't function until the random number
generator is initialised, meaning lots of people have been seeing large
delays before they could log into systems with default MQ kernels due to
this lack of entropy, because it now can take tens of minutes to initialise
the kernel random number generator.
The fix is to set the non-rotational and add-randomness flags
unconditionally early on in the disk initialization path, so they can be
reset only if the device actually reports being non-rotational via the VPD
page.
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Fixes: 83e32a5910 ("scsi: sd: Contribute to randomness when running rotational device")
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Xuewei Zhang <xueweiz@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0722069a53 upstream.
When printing multiple uprobe arguments as strings the output for the
earlier arguments would also include all later string arguments.
This is best explained in an example:
Consider adding a uprobe to a function receiving two strings as
parameters which is at offset 0xa0 in strlib.so and we want to print
both parameters when the uprobe is hit (on x86_64):
$ echo 'p:func /lib/strlib.so:0xa0 +0(%di):string +0(%si):string' > \
/sys/kernel/debug/tracing/uprobe_events
When the function is called as func("foo", "bar") and we hit the probe,
the trace file shows a line like the following:
[...] func: (0x7f7e683706a0) arg1="foobar" arg2="bar"
Note the extra "bar" printed as part of arg1. This behaviour stacks up
for additional string arguments.
The strings are stored in a dynamically growing part of the uprobe
buffer by fetch_store_string() after copying them from userspace via
strncpy_from_user(). The return value of strncpy_from_user() is then
directly used as the required size for the string. However, this does
not take the terminating null byte into account as the documentation
for strncpy_from_user() cleary states that it "[...] returns the
length of the string (not including the trailing NUL)" even though the
null byte will be copied to the destination.
Therefore, subsequent calls to fetch_store_string() will overwrite
the terminating null byte of the most recently fetched string with
the first character of the current string, leading to the
"accumulation" of strings in earlier arguments in the output.
Fix this by incrementing the return value of strncpy_from_user() by
one if we did not hit the maximum buffer size.
Link: http://lkml.kernel.org/r/20190116141629.5752-1-andreas.ziegler@fau.de
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5baaa59ef0 ("tracing/probes: Implement 'memory' fetch method for uprobes")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f9aca0c45 upstream.
The older machines don't have the QCI instruction available.
With support for up to 256 crypto cards the probing of each
card has been extended to check card ids from 0 up to 255.
For machines with QCI support there is a filter limiting the
range of probed cards. The older machines (z196 and older)
don't have this filter and so since support for 256 cards is
in the driver all cards are probed. However, these machines
also require to have the card id fit into 6 bits. Exceeding
this limit results in a specification exception which happens
on every kernel startup even when there is no crypto configured
and used at all.
This fix limits the range of probed crypto cards to 64 if
there is no QCI instruction available to obey to the older
ap architecture and so fixes the specification exceptions
on z196 machines.
Cc: stable@vger.kernel.org # v4.17+
Fixes: af4a72276d ("s390/zcrypt: Support up to 256 crypto adapters.")
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
