commit f1ffa9d4cc upstream.
Commit 95722237cb ("ACPI: sleep: Put the FACS table after using it")
puts the FACS table during initialization.
But the hardware signature bits in the FACS table need to be accessed,
after every hibernation, to compare with the original hardware
signature.
So there is no reason to release the FACS table mapping after
initialization.
This reverts commit 95722237cb.
An alternative solution is to use acpi_gbl_FACS variable instead, which
is mapped by the ACPICA core and never released.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=212277
Reported-by: Stephan Hohe <sth.dev@tejp.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 5.8+ <stable@vger.kernel.org> # 5.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13817d466e upstream.
Commit 571e31fa60 ("spi: bcm2835: Cache CS register value for
->prepare_message()") limited the number of slaves to 3 at compile-time.
The limitation was necessitated by a statically-sized array prepare_cs[]
in the driver private data which contains a per-slave register value.
The commit sought to enforce the limitation at run-time by setting the
controller's num_chipselect to 3: Slaves with a higher chipselect are
rejected by spi_add_device().
However the commit neglected that num_chipselect only limits the number
of *native* chipselects. If GPIO chipselects are specified in the
device tree for more than 3 slaves, num_chipselect is silently raised by
of_spi_get_gpio_numbers() and the result are out-of-bounds accesses to
the statically-sized array prepare_cs[].
As a bandaid fix which is backportable to stable, raise the number of
allowed slaves to 24 (which "ought to be enough for anybody"), enforce
the limitation on slave ->setup and revert num_chipselect to 3 (which is
the number of native chipselects supported by the controller).
An upcoming for-next commit will allow an arbitrary number of slaves.
Fixes: 571e31fa60 ("spi: bcm2835: Cache CS register value for ->prepare_message()")
Reported-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.4+
Cc: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/75854affc1923309fde05e47494263bde73e5592.1621703210.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57c9e21a49 upstream.
There are 2 issues on this machine, the 1st one is mic's plug/unplug
can't be detected, that is because the mic is set to manual detecting
mode, need to apply ALC255_FIXUP_XIAOMI_HEADSET_MIC to set it to auto
detecting mode. The other one is headphone's plug/unplug can't be
detected by pulseaudio, that is because the pulseaudio will use
ucm2/sof-hda-dsp on this machine, and the ucm2 only handle
'Headphone Jack', but on this machine the headphone's pincfg sets the
location to Front, then the alsa mixer name is "Front Headphone Jack"
instead of "Headphone Jack", so override the pincfg to change location
to Left.
BugLink: http://bugs.launchpad.net/bugs/1930188
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210608024600.6198-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f0cdec8b5 ]
The P2040/P2041 has an erratum where the normal i2c recovery mechanism
does not work. Implement the alternative recovery mechanism documented
in the P2040 Chip Errata Rev Q.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65171b2df1 ]
Move the existing calls of mpc_i2c_fixup() to a recovery function
registered via bus_recovery_info. This makes it more obvious that
recovery is supported and allows for a future where recovery is
triggered by the i2c core.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ec6f20b33 ]
Commit c7299fea67 ("spi: Fix spi device unregister flow") changed the
SPI core's behavior if the ->setup() hook returns an error upon adding
an spi_device: Before, the ->cleanup() hook was invoked to free any
allocations that were made by ->setup(). With the commit, that's no
longer the case, so the ->setup() hook is expected to free the
allocations itself.
I've identified 5 drivers which depend on the old behavior and am fixing
them up hereinafter: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c spi-pxa2xx.c
Importantly, ->setup() is not only invoked on spi_device *addition*:
It may subsequently be called to *change* SPI parameters. If changing
these SPI parameters fails, freeing memory allocations would be wrong.
That should only be done if the spi_device is finally destroyed.
I am therefore using a bool "initial_setup" in 4 of the affected drivers
to differentiate between the invocation on *adding* the spi_device and
any subsequent invocations: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c
In spi-pxa2xx.c, it seems the ->setup() hook can only fail on spi_device
addition, not any subsequent calls. It therefore doesn't need the bool.
It's worth noting that 5 other drivers already perform a cleanup if the
->setup() hook fails. Before c7299fea67, they caused a double-free
if ->setup() failed on spi_device addition. Since the commit, they're
fine. These drivers are: spi-mpc512x-psc.c spi-pl022.c spi-s3c64xx.c
spi-st-ssc4.c spi-tegra114.c
(spi-pxa2xx.c also already performs a cleanup, but only in one of
several error paths.)
Fixes: c7299fea67 ("spi: Fix spi device unregister flow")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Saravana Kannan <saravanak@google.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # pxa2xx
Link: https://lore.kernel.org/r/f76a0599469f265b69c371538794101fa37b5536.1622149321.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19ae697a1e ]
The i2c controllers on the P1010 have an erratum where the documented
scheme for i2c bus recovery will not work (A-004447). A different
mechanism is needed which is documented in the P1010 Chip Errata Rev L.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7adc7b225c ]
The i2c controllers on the P2040/P2041 have an erratum where the
documented scheme for i2c bus recovery will not work (A-004447). A
different mechanism is needed which is documented in the P2040 Chip
Errata Rev Q (latest available at the time of writing).
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaeadd7075 ]
Controller teardown flow may take some time in case it has many I/O
queues, and the host may not send us keep-alive during this period.
Hence reset the traffic based keep-alive timer so we don't trigger
a controller teardown as a result of a keep-alive expiration.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c1f3193b1 ]
The third parameter of module_param() is permissions for the sysfs node
but it looks like it is being used as the initial value of the parameter
here. In fact, false here equates to omitting the file from sysfs and
does not affect the value of require_signatures.
Making the parameter writable is not simple because going from
false->true is fine but it should not be possible to remove the
requirement to verify a signature. But it can be useful to inspect the
value of this parameter from userspace, so change the permissions to
make a read-only file in sysfs.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78cf0eb926 ]
When update the latest mainline kernel with the following three configs,
the kernel hangs during startup:
(1) CONFIG_FUNCTION_GRAPH_TRACER=y
(2) CONFIG_PREEMPT_TRACER=y
(3) CONFIG_FTRACE_STARTUP_TEST=y
When update the latest mainline kernel with the above two configs (1)
and (2), the kernel starts normally, but it still hangs when execute
the following command:
echo "function_graph" > /sys/kernel/debug/tracing/current_tracer
Without CONFIG_PREEMPT_TRACER=y, the above two kinds of kernel hangs
disappeared, so it seems that CONFIG_PREEMPT_TRACER has some influences
with function_graph tracer at the first glance.
I use ejtag to find out the epc address is related with preempt_enable()
in the file arch/mips/lib/mips-atomic.c, because function tracing can
trace the preempt_{enable,disable} calls that are traced, replace them
with preempt_{enable,disable}_notrace to prevent function tracing from
going into an infinite loop, and then it can fix the kernel hang issue.
By the way, it seems that this commit is a complement and improvement of
commit f93a1a00f2 ("MIPS: Fix crash that occurs when function tracing
is enabled").
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4dd4fc610 ]
In cops_probe1(), there is a write to dev->base_addr after requesting an
interrupt line and registering the interrupt handler cops_interrupt().
The handler might be called in parallel to handle an interrupt.
cops_interrupt() tries to read dev->base_addr leading to a potential
data race. So write to dev->base_addr before calling request_irq().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Saubhik Mukherjee <saubhik.mukherjee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5eff1461a6 ]
If runtime power menagement is enabled, the gigabit ethernet PLL would
be disabled after macb_probe(). During this period of time, the system
would hang up if we try to access GEMGXL control registers.
We can't put runtime_pm_get/runtime_pm_put/ there due to the issue of
sleep inside atomic section (7fa2955ff7 ("sh_eth: Fix sleeping
function called from invalid context"). Add netif_running checking to
ensure the device is available before accessing GEMGXL device.
Changed in v2:
- Use netif_running instead of its own flag
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ef7665dfd ]
Target de-configuration panics at high CPU load because TPGT and WWPN can
be removed on separate threads.
TPGT removal requests a reset HBA on a separate thread and waits for reset
complete (phase1). Due to high CPU load that HBA reset can be delayed for
some time.
WWPN removal does qlt_stop_phase2(). There it is believed that phase1 has
already completed and thus tgt.tgt_ops is subsequently cleared. However,
tgt.tgt_ops is needed to process incoming traffic and therefore this will
cause one of the following panics:
NIP qlt_reset+0x7c/0x220 [qla2xxx]
LR qlt_reset+0x68/0x220 [qla2xxx]
Call Trace:
0xc000003ffff63a78 (unreliable)
qlt_handle_imm_notify+0x800/0x10c0 [qla2xxx]
qlt_24xx_atio_pkt+0x208/0x590 [qla2xxx]
qlt_24xx_process_atio_queue+0x33c/0x7a0 [qla2xxx]
qla83xx_msix_atio_q+0x54/0x90 [qla2xxx]
or
NIP qlt_24xx_handle_abts+0xd0/0x2a0 [qla2xxx]
LR qlt_24xx_handle_abts+0xb4/0x2a0 [qla2xxx]
Call Trace:
qlt_24xx_handle_abts+0x90/0x2a0 [qla2xxx] (unreliable)
qlt_24xx_process_atio_queue+0x500/0x7a0 [qla2xxx]
qla83xx_msix_atio_q+0x54/0x90 [qla2xxx]
or
NIP qlt_create_sess+0x90/0x4e0 [qla2xxx]
LR qla24xx_do_nack_work+0xa8/0x180 [qla2xxx]
Call Trace:
0xc0000000348fba30 (unreliable)
qla24xx_do_nack_work+0xa8/0x180 [qla2xxx]
qla2x00_do_work+0x674/0xbf0 [qla2xxx]
qla2x00_iocb_work_fn
The patch fixes the issue by serializing qlt_stop_phase1() and
qlt_stop_phase2() functions to make WWPN removal wait for phase1
completion.
Link: https://lore.kernel.org/r/20210415203554.27890-1-d.bogdanov@yadro.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f03eeb6e0 ]
SFC driver can be configured via modparam to work using MSI-X, MSI or
legacy IRQ interrupts. In the last one, the interrupt was not properly
released on module remove.
It was not freed because the flag irqs_hooked was not set during
initialization in the case of using legacy IRQ.
Example of (trimmed) trace during module remove without this fix:
remove_proc_entry: removing non-empty directory 'irq/125', leaking at least '0000:3b:00.1'
WARNING: CPU: 39 PID: 3658 at fs/proc/generic.c:715 remove_proc_entry+0x15c/0x170
...trimmed...
Call Trace:
unregister_irq_proc+0xe3/0x100
free_desc+0x29/0x70
irq_free_descs+0x47/0x70
mp_unmap_irq+0x58/0x60
acpi_unregister_gsi_ioapic+0x2a/0x40
acpi_pci_irq_disable+0x78/0xb0
pci_disable_device+0xd1/0x100
efx_pci_remove+0xa1/0x1e0 [sfc]
pci_device_remove+0x38/0xa0
__device_release_driver+0x177/0x230
driver_detach+0xcb/0x110
bus_remove_driver+0x58/0xd0
pci_unregister_driver+0x2a/0xb0
efx_exit_module+0x24/0xf40 [sfc]
__do_sys_delete_module.constprop.0+0x171/0x280
? exit_to_user_mode_prepare+0x83/0x1d0
do_syscall_64+0x3d/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f9f9385800b
...trimmed...
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aced3ce57c ]
When TCP is used as transport and a program on the
system connects to RDS port 16385, connection is
accepted but denied per the rules of RDS. However,
RDS connections object is left in the list. Next
loopback connection will select that connection
object as it is at the head of list. The connection
attempt will hang as the connection object is set
to connect over TCP which is not allowed
The issue can be reproduced easily, use rds-ping
to ping a local IP address. After that use any
program like ncat to connect to the same IP
address and port 16385. This will hang so ctrl-c out.
Now try rds-ping, it will hang.
To fix the issue this patch adds checks to disallow
the connection object creation and destroys the
connection object.
Signed-off-by: Rao Shoaib <rao.shoaib@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 940d71c646 ]
If VCPU is suspended (VM suspend) in wq_watchdog_timer_fn() then
once this VCPU resumes it will see the new jiffies value, while it
may take a while before IRQ detects PVCLOCK_GUEST_STOPPED on this
VCPU and updates all the watchdogs via pvclock_touch_watchdogs().
There is a small chance of misreported WQ stalls in the meantime,
because new jiffies is time_after() old 'ts + thresh'.
wq_watchdog_timer_fn()
{
for_each_pool(pool, pi) {
if (time_after(jiffies, ts + thresh)) {
pr_emerg("BUG: workqueue lockup - pool");
}
}
}
Save jiffies at the beginning of this function and use that value
for stall detection. If VM gets suspended then we continue using
"old" jiffies value and old WQ touch timestamps. If IRQ at some
point restarts the stall detection cycle (pvclock_touch_watchdogs())
then old jiffies will always be before new 'ts + thresh'.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45e1ba4083 ]
This patch effectively reverts the commit a3e72739b7 ("cgroup: fix
too early usage of static_branch_disable()"). The commit 6041186a32
("init: initialize jump labels before command line option parsing") has
moved the jump_label_init() before parse_args() which has made the
commit a3e72739b7 unnecessary. On the other hand there are
consequences of disabling the controllers later as there are subsystems
doing the controller checks for different decisions. One such incident
is reported [1] regarding the memory controller and its impact on memory
reclaim code.
[1] https://lore.kernel.org/linux-mm/921e53f3-4b13-aab8-4a9e-e83ff15371e4@nec.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reported-by: NOMURA JUNICHI(野村 淳一) <junichi.nomura@nec.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Jun'ichi Nomura <junichi.nomura@nec.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dde47a66d ]
We spotted a bug recently during a review where a driver was
unregistering a bus that wasn't registered, which would trigger this
BUG_ON(). Let's handle that situation more gracefully, and just print
a warning and return.
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d482e666b ]
Syzbot reports that in mac80211 we have a potential deadlock
between our "local->stop_queue_reasons_lock" (spinlock) and
netlink's nl_table_lock (rwlock). This is because there's at
least one situation in which we might try to send a netlink
message with this spinlock held while it is also possible to
take the spinlock from a hardirq context, resulting in the
following deadlock scenario reported by lockdep:
CPU0 CPU1
---- ----
lock(nl_table_lock);
local_irq_disable();
lock(&local->queue_stop_reason_lock);
lock(nl_table_lock);
<Interrupt>
lock(&local->queue_stop_reason_lock);
This seems valid, we can take the queue_stop_reason_lock in
any kind of context ("CPU0"), and call ieee80211_report_ack_skb()
with the spinlock held and IRQs disabled ("CPU1") in some
code path (ieee80211_do_stop() via ieee80211_free_txskb()).
Short of disallowing netlink use in scenarios like these
(which would be rather complex in mac80211's case due to
the deep callchain), it seems the only fix for this is to
disable IRQs while nl_table_lock is held to avoid hitting
this scenario, this disallows the "CPU0" portion of the
reported deadlock.
Note that the writer side (netlink_table_grab()) already
disables IRQs for this lock.
Unfortunately though, this seems like a huge hammer, and
maybe the whole netlink table locking should be reworked.
Reported-by: syzbot+69ff9dff50dcfe14ddd4@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35d96e6318 ]
If bond_kobj_init() or later kzalloc() in bond_alloc_slave() fail,
then we call kobject_put() on the slave->kobj. This in turn calls
the release function slave_kobj_release() which will always try to
cancel_delayed_work_sync(&slave->notify_work), which shouldn't be
done on an uninitialized work struct.
Always initialize the work struct earlier to avoid problems here.
Syzbot bisected this down to a completely pointless commit, some
fault injection may have been at work here that caused the alloc
failure in the first place, which may interact badly with bisect.
Reported-by: syzbot+bfda097c12a00c8cae67@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2af7a834a4 ]
Today, the stacked call to vfio_ccw_sch_io_todo() does three things:
1) Update a solicited IRB with CP information, and release the CP
if the interrupt was the end of a START operation.
2) Copy the IRB data into the io_region, under the protection of
the io_mutex
3) Reset the vfio-ccw FSM state to IDLE to acknowledge that
vfio-ccw can accept more work.
The trouble is that step 3 is (A) invoked for both solicited and
unsolicited interrupts, and (B) sitting after the mutex for step 2.
This second piece becomes a problem if it processes an interrupt
for a CLEAR SUBCHANNEL while another thread initiates a START,
thus allowing the CP and FSM states to get out of sync. That is:
CPU 1 CPU 2
fsm_do_clear()
fsm_irq()
fsm_io_request()
vfio_ccw_sch_io_todo()
fsm_io_helper()
Since the FSM state and CP should be kept in sync, let's make a
note when the CP is released, and rely on that as an indication
that the FSM should also be reset at the end of this routine and
open up the device for more work.
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Acked-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20210511195631.3995081-4-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c02ac4c92 ]
When an I/O request is made, the fsm_io_request() routine
moves the FSM state from IDLE to CP_PROCESSING, and then
fsm_io_helper() moves it to CP_PENDING if the START SUBCHANNEL
received a cc0. Yet, the error case to go from CP_PROCESSING
back to IDLE is done after the FSM call returns.
Let's move this up into the FSM proper, to provide some
better symmetry when unwinding in this case.
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20210511195631.3995081-3-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ab78863e9 ]
The function rawsock_create() calls a privileged function sk_alloc(), which requires a ns-aware check to check net->user_ns, i.e., ns_capable(). However, the original code checks the init_user_ns using capable(). So we replace the capable() with ns_capable().
Signed-off-by: Jeimon <jjjinmeng.zhou@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7299fea67 ]
When an SPI device is unregistered, the spi->controller->cleanup() is
called in the device's release callback. That's wrong for a couple of
reasons:
1. spi_dev_put() can be called before spi_add_device() is called. And
it's spi_add_device() that calls spi_setup(). This will cause clean()
to get called without the spi device ever being setup.
2. There's no guarantee that the controller's driver would be present by
the time the spi device's release function gets called.
3. It also causes "sleeping in atomic context" stack dump[1] when device
link deletion code does a put_device() on the spi device.
Fix these issues by simply moving the cleanup from the device release
callback to the actual spi_unregister_device() function.
[1] - https://lore.kernel.org/lkml/CAHp75Vc=FCGcUyS0v6fnxme2YJ+qD+Y-hQDQLa2JhWNON9VmsQ@mail.gmail.com/
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210426235638.1285530-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
