Changes in 5.10.17
objtool: Fix seg fault with Clang non-section symbols
Revert "dts: phy: add GPIO number and active state used for phy reset"
gpio: mxs: GPIO_MXS should not default to y unconditionally
gpio: ep93xx: fix BUG_ON port F usage
gpio: ep93xx: Fix single irqchip with multi gpiochips
tracing: Do not count ftrace events in top level enable output
tracing: Check length before giving out the filter buffer
drm/i915: Fix overlay frontbuffer tracking
arm/xen: Don't probe xenbus as part of an early initcall
cgroup: fix psi monitor for root cgroup
Revert "drm/amd/display: Update NV1x SR latency values"
drm/i915/tgl+: Make sure TypeC FIA is powered up when initializing it
drm/dp_mst: Don't report ports connected if nothing is attached to them
dmaengine: move channel device_node deletion to driver
tmpfs: disallow CONFIG_TMPFS_INODE64 on s390
tmpfs: disallow CONFIG_TMPFS_INODE64 on alpha
soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1
arm64: dts: rockchip: Fix PCIe DT properties on rk3399
arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node
platform/x86: hp-wmi: Disable tablet-mode reporting by default
arm64: dts: rockchip: Disable display for NanoPi R2S
ovl: perform vfs_getxattr() with mounter creds
cap: fix conversions on getxattr
ovl: skip getxattr of security labels
scsi: lpfc: Fix EEH encountering oops with NVMe traffic
x86/split_lock: Enable the split lock feature on another Alder Lake CPU
nvme-pci: ignore the subsysem NQN on Phison E16
drm/amd/display: Fix DPCD translation for LTTPR AUX_RD_INTERVAL
drm/amd/display: Add more Clock Sources to DCN2.1
drm/amd/display: Release DSC before acquiring
drm/amd/display: Fix dc_sink kref count in emulated_link_detect
drm/amd/display: Free atomic state after drm_atomic_commit
drm/amd/display: Decrement refcount of dc_sink before reassignment
riscv: virt_addr_valid must check the address belongs to linear mapping
bfq-iosched: Revert "bfq: Fix computation of shallow depth"
ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
kallsyms: fix nonconverging kallsyms table with lld
ARM: ensure the signal page contains defined contents
ARM: kexec: fix oops after TLB are invalidated
ubsan: implement __ubsan_handle_alignment_assumption
Revert "lib: Restrict cpumask_local_spread to houskeeping CPUs"
x86/efi: Remove EFI PGD build time checks
lkdtm: don't move ctors to .rodata
KVM: x86: cleanup CR3 reserved bits checks
cgroup-v1: add disabled controller check in cgroup1_parse_param()
dmaengine: idxd: fix misc interrupt completion
ath9k: fix build error with LEDS_CLASS=m
mt76: dma: fix a possible memory leak in mt76_add_fragment()
drm/vc4: hvs: Fix buffer overflow with the dlist handling
dmaengine: idxd: check device state before issue command
bpf: Unbreak BPF_PROG_TYPE_KPROBE when kprobe is called via do_int3
bpf: Check for integer overflow when using roundup_pow_of_two()
netfilter: xt_recent: Fix attempt to update deleted entry
selftests: netfilter: fix current year
netfilter: nftables: fix possible UAF over chains from packet path in netns
netfilter: flowtable: fix tcp and udp header checksum update
xen/netback: avoid race in xenvif_rx_ring_slots_available()
net: hdlc_x25: Return meaningful error code in x25_open
net: ipa: set error code in gsi_channel_setup()
hv_netvsc: Reset the RSC count if NVSP_STAT_FAIL in netvsc_receive()
net: enetc: initialize the RFS and RSS memories
selftests: txtimestamp: fix compilation issue
net: stmmac: set TxQ mode back to DCB after disabling CBS
ibmvnic: Clear failover_pending if unable to schedule
netfilter: conntrack: skip identical origin tuple in same zone only
scsi: scsi_debug: Fix a memory leak
x86/build: Disable CET instrumentation in the kernel for 32-bit too
net: dsa: felix: implement port flushing on .phylink_mac_link_down
net: hns3: add a check for queue_id in hclge_reset_vf_queue()
net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()
net: hns3: add a check for index in hclge_get_rss_key()
firmware_loader: align .builtin_fw to 8
drm/sun4i: tcon: set sync polarity for tcon1 channel
drm/sun4i: dw-hdmi: always set clock rate
drm/sun4i: Fix H6 HDMI PHY configuration
drm/sun4i: dw-hdmi: Fix max. frequency for H6
clk: sunxi-ng: mp: fix parent rate change flag check
i2c: stm32f7: fix configuration of the digital filter
h8300: fix PREEMPTION build, TI_PRE_COUNT undefined
scripts: set proper OpenSSL include dir also for sign-file
x86/pci: Create PCI/MSI irqdomain after x86_init.pci.arch_init()
arm64: mte: Allow PTRACE_PEEKMTETAGS access to the zero page
rxrpc: Fix clearance of Tx/Rx ring when releasing a call
udp: fix skb_copy_and_csum_datagram with odd segment sizes
net: dsa: call teardown method on probe failure
cpufreq: ACPI: Extend frequency tables to cover boost frequencies
cpufreq: ACPI: Update arch scale-invariance max perf ratio if CPPC is not there
net: gro: do not keep too many GRO packets in napi->rx_list
net: fix iteration for sctp transport seq_files
net/vmw_vsock: fix NULL pointer dereference
net/vmw_vsock: improve locking in vsock_connect_timeout()
net: watchdog: hold device global xmit lock during tx disable
bridge: mrp: Fix the usage of br_mrp_port_switchdev_set_state
switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STAT
vsock/virtio: update credit only if socket is not closed
vsock: fix locking in vsock_shutdown()
net/rds: restrict iovecs length for RDS_CMSG_RDMA_ARGS
net/qrtr: restrict user-controlled length in qrtr_tun_write_iter()
ovl: expand warning in ovl_d_real()
kcov, usb: only collect coverage from __usb_hcd_giveback_urb in softirq
Linux 5.10.17
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Id0300681f52b51d3f466f1e66ec3a6c25f65f4d3
commit aee9ddb1d3 upstream.
Currently there's a KCOV remote coverage collection section in
__usb_hcd_giveback_urb(). Initially that section was added based on the
assumption that usb_hcd_giveback_urb() can only be called in interrupt
context as indicated by a comment before it. This is what happens when
syzkaller is fuzzing the USB stack via the dummy_hcd driver.
As it turns out, it's actually valid to call usb_hcd_giveback_urb() in task
context, provided that the caller turned off the interrupts; USB/IP does
exactly that. This can lead to a nested KCOV remote coverage collection
sections both trying to collect coverage in task context. This isn't
supported by KCOV, and leads to a WARNING.
Change __usb_hcd_giveback_urb() to only call kcov_remote_*() callbacks
when it's being executed in a softirq. As the result, the coverage from
USB/IP related usb_hcd_giveback_urb() calls won't be collected, but the
WARNING is fixed.
A potential future improvement would be to support nested remote coverage
collection sections, but this patch doesn't address that.
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/f3a7a153f0719cb53ec385b16e912798bd3e4cf9.1602856358.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a11148e6fc upstream.
syzbot found WARNING in rds_rdma_extra_size [1] when RDS_CMSG_RDMA_ARGS
control message is passed with user-controlled
0x40001 bytes of args->nr_local, causing order >= MAX_ORDER condition.
The exact value 0x40001 can be checked with UIO_MAXIOV which is 0x400.
So for kcalloc() 0x400 iovecs with sizeof(struct rds_iovec) = 0x10
is the closest limit, with 0x10 leftover.
Same condition is currently done in rds_cmsg_rdma_args().
[1] WARNING: mm/page_alloc.c:5011
[..]
Call Trace:
alloc_pages_current+0x18c/0x2a0 mm/mempolicy.c:2267
alloc_pages include/linux/gfp.h:547 [inline]
kmalloc_order+0x2e/0xb0 mm/slab_common.c:837
kmalloc_order_trace+0x14/0x120 mm/slab_common.c:853
kmalloc_array include/linux/slab.h:592 [inline]
kcalloc include/linux/slab.h:621 [inline]
rds_rdma_extra_size+0xb2/0x3b0 net/rds/rdma.c:568
rds_rm_size net/rds/send.c:928 [inline]
Reported-by: syzbot+1bd2b07f93745fa38425@syzkaller.appspotmail.com
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/20210201203233.1324704-1-snovitoll@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c5fae9c9a upstream.
In vsock_shutdown() we touched some socket fields without holding the
socket lock, such as 'state' and 'sk_flags'.
Also, after the introduction of multi-transport, we are accessing
'vsk->transport' in vsock_send_shutdown() without holding the lock
and this call can be made while the connection is in progress, so
the transport can change in the meantime.
To avoid issues, we hold the socket lock when we enter in
vsock_shutdown() and release it when we leave.
Among the transports that implement the 'shutdown' callback, only
hyperv_transport acquired the lock. Since the caller now holds it,
we no longer take it.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce7536bc73 upstream.
If the socket is closed or is being released, some resources used by
virtio_transport_space_update() such as 'vsk->trans' may be released.
To avoid a use after free bug we should only update the available credit
when we are sure the socket is still open and we have the lock held.
Fixes: 06a8fc7836 ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210208144454.84438-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 059d2a1004 upstream.
Now that MRP started to use also SWITCHDEV_ATTR_ID_PORT_STP_STATE to
notify HW, then SWITCHDEV_ATTR_ID_MRP_PORT_STAT is not used anywhere
else, therefore we can remove it.
Fixes: c284b54590 ("switchdev: mrp: Extend switchdev API to offload MRP")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2bdba1cbc upstream.
The function br_mrp_port_switchdev_set_state was called both with MRP
port state and STP port state, which is an issue because they don't
match exactly.
Therefore, update the function to be used only with STP port state and
use the id SWITCHDEV_ATTR_ID_PORT_STP_STATE.
The choice of using STP over MRP is that the drivers already implement
SWITCHDEV_ATTR_ID_PORT_STP_STATE and already in SW we update the port
STP state.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Fixes: fadd409136 ("bridge: switchdev: mrp: Implement MRP API for switchdev")
Fixes: 2f1a11ae11 ("bridge: mrp: Add MRP interface.")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3aa6bce9af upstream.
Prevent netif_tx_disable() running concurrently with dev_watchdog() by
taking the device global xmit lock. Otherwise, the recommended:
netif_carrier_off(dev);
netif_tx_disable(dev);
driver shutdown sequence can happen after the watchdog has already
checked carrier, resulting in possible false alarms. This is because
netif_tx_lock() only sets the frozen bit without maintaining the locks
on the individual queues.
Fixes: c3f26a269c ("netdev: Fix lockdep warnings in multiqueue configurations.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d1cbcc990 upstream.
In vsock_stream_connect(), a thread will enter schedule_timeout().
While being scheduled out, another thread can enter vsock_stream_connect()
as well and set vsk->transport to NULL. In case a signal was sent, the
first thread can leave schedule_timeout() and vsock_transport_cancel_pkt()
will be called right after. Inside vsock_transport_cancel_pkt(), a null
dereference will happen on transport->cancel_pkt.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Signed-off-by: Norbert Slusarek <nslusarek@gmx.net>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/trinity-c2d6cede-bfb1-44e2-85af-1fbc7f541715-1612535117028@3c-app-gmx-bap12
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af8085f3a4 upstream.
The sctp transport seq_file iterators take a reference to the transport
in the ->start and ->next functions and releases the reference in the
->show function. The preferred handling for such resources is to
release them in the subsequent ->next or ->stop function call.
Since Commit 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration
code and interface") there is no guarantee that ->show will be called
after ->next, so this function can now leak references.
So move the sctp_transport_put() call to ->next and ->stop.
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code and interface")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d11a1d08a0 upstream.
If the maximum performance level taken for computing the
arch_max_freq_ratio value used in the x86 scale-invariance code is
higher than the one corresponding to the cpuinfo.max_freq value
coming from the acpi_cpufreq driver, the scale-invariant utilization
falls below 100% even if the CPU runs at cpuinfo.max_freq or slightly
faster, which causes the schedutil governor to select a frequency
below cpuinfo.max_freq. That frequency corresponds to a frequency
table entry below the maximum performance level necessary to get to
the "boost" range of CPU frequencies which prevents "boost"
frequencies from being used in some workloads.
While this issue is related to scale-invariance, it may be amplified
by commit db865272d9 ("cpufreq: Avoid configuring old governors as
default with intel_pstate") from the 5.10 development cycle which
made it extremely easy to default to schedutil even if the preferred
driver is acpi_cpufreq as long as intel_pstate is built too, because
the mere presence of the latter effectively removes the ondemand
governor from the defaults. Distro kernels are likely to include
both intel_pstate and acpi_cpufreq on x86, so their users who cannot
use intel_pstate or choose to use acpi_cpufreq may easily be
affectecd by this issue.
If CPPC is available, it can be used to address this issue by
extending the frequency tables created by acpi_cpufreq to cover the
entire available frequency range (including "boost" frequencies) for
each CPU, but if CPPC is not there, acpi_cpufreq has no idea what
the maximum "boost" frequency is and the frequency tables created by
it cannot be extended in a meaningful way, so in that case make it
ask the arch scale-invariance code to to use the "nominal" performance
level for CPU utilization scaling in order to avoid the issue at hand.
Fixes: db865272d9 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c55e94c0a upstream.
A severe performance regression on AMD EPYC processors when using
the schedutil scaling governor was discovered by Phoronix.com and
attributed to the following commits:
41ea667227 ("x86, sched: Calculate frequency invariance for AMD
systems")
976df7e573 ("x86, sched: Use midpoint of max_boost and max_P for
frequency invariance on AMD EPYC")
The source of the problem is that the maximum performance level taken
for computing the arch_max_freq_ratio value used in the x86 scale-
invariance code is higher than the one corresponding to the
cpuinfo.max_freq value coming from the acpi_cpufreq driver.
This effectively causes the scale-invariant utilization to fall below
100% even if the CPU runs at cpuinfo.max_freq or slightly faster, so
the schedutil governor selects a frequency below cpuinfo.max_freq
then. That frequency corresponds to a frequency table entry below
the maximum performance level necessary to get to the "boost" range
of CPU frequencies.
However, if the cpuinfo.max_freq value coming from acpi_cpufreq was
higher, the schedutil governor would select higher frequencies which
in turn would allow acpi_cpufreq to set more adequate performance
levels and to get to the "boost" range of CPU frequencies more often.
This issue affects any systems where acpi_cpufreq is used and the
"boost" (or "turbo") frequencies are enabled, not just AMD EPYC.
Moreover, commit db865272d9 ("cpufreq: Avoid configuring old
governors as default with intel_pstate") from the 5.10 development
cycle made it extremely easy to default to schedutil even if the
preferred driver is acpi_cpufreq as long as intel_pstate is built
too, because the mere presence of the latter effectively removes the
ondemand governor from the defaults. Distro kernels are likely to
include both intel_pstate and acpi_cpufreq on x86, so their users
who cannot use intel_pstate or choose to use acpi_cpufreq may
easily be affectecd by this issue.
To address this issue, extend the frequency table constructed by
acpi_cpufreq for each CPU to cover the entire range of available
frequencies (including the "boost" ones) if CPPC is available and
indicates that "boost" (or "turbo") frequencies are enabled. That
causes cpuinfo.max_freq to become the maximum "boost" frequency of
the given CPU (instead of the maximum frequency returned by the ACPI
_PSS object that corresponds to the "nominal" performance level).
Fixes: 41ea667227 ("x86, sched: Calculate frequency invariance for AMD systems")
Fixes: 976df7e573 ("x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC")
Fixes: db865272d9 ("cpufreq: Avoid configuring old governors as default with intel_pstate")
Link: https://www.phoronix.com/scan.php?page=article&item=linux511-amd-schedutil&num=1
Link: https://lore.kernel.org/linux-pm/20210203135321.12253-2-ggherdovich@suse.cz/
Reported-by: Michael Larabel <Michael@phoronix.com>
Diagnosed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Reviewed-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Tested-by: Michael Larabel <Michael@phoronix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b5eab57ca upstream.
At the end of rxrpc_release_call(), rxrpc_cleanup_ring() is called to clear
the Rx/Tx skbuff ring, but this doesn't lock the ring whilst it's accessing
it. Unfortunately, rxrpc_resend() might be trying to retransmit a packet
concurrently with this - and whilst it does lock the ring, this isn't
protection against rxrpc_cleanup_call().
Fix this by removing the call to rxrpc_cleanup_ring() from
rxrpc_release_call(). rxrpc_cleanup_ring() will be called again anyway
from rxrpc_cleanup_call(). The earlier call is just an optimisation to
recycle skbuffs more quickly.
Alternative solutions include rxrpc_release_call() could try to cancel the
work item or wait for it to complete or rxrpc_cleanup_ring() could lock
when accessing the ring (which would require a bh lock).
This can produce a report like the following:
BUG: KASAN: use-after-free in rxrpc_send_data_packet+0x19b4/0x1e70 net/rxrpc/output.c:372
Read of size 4 at addr ffff888011606e04 by task kworker/0:0/5
...
Workqueue: krxrpcd rxrpc_process_call
Call Trace:
...
kasan_report.cold+0x79/0xd5 mm/kasan/report.c:413
rxrpc_send_data_packet+0x19b4/0x1e70 net/rxrpc/output.c:372
rxrpc_resend net/rxrpc/call_event.c:266 [inline]
rxrpc_process_call+0x1634/0x1f60 net/rxrpc/call_event.c:412
process_one_work+0x98d/0x15f0 kernel/workqueue.c:2275
...
Allocated by task 2318:
...
sock_alloc_send_pskb+0x793/0x920 net/core/sock.c:2348
rxrpc_send_data+0xb51/0x2bf0 net/rxrpc/sendmsg.c:358
rxrpc_do_sendmsg+0xc03/0x1350 net/rxrpc/sendmsg.c:744
rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:560
...
Freed by task 2318:
...
kfree_skb+0x140/0x3f0 net/core/skbuff.c:704
rxrpc_free_skb+0x11d/0x150 net/rxrpc/skbuff.c:78
rxrpc_cleanup_ring net/rxrpc/call_object.c:485 [inline]
rxrpc_release_call+0x5dd/0x860 net/rxrpc/call_object.c:552
rxrpc_release_calls_on_socket+0x21c/0x300 net/rxrpc/call_object.c:579
rxrpc_release_sock net/rxrpc/af_rxrpc.c:885 [inline]
rxrpc_release+0x263/0x5a0 net/rxrpc/af_rxrpc.c:916
__sock_release+0xcd/0x280 net/socket.c:597
...
The buggy address belongs to the object at ffff888011606dc0
which belongs to the cache skbuff_head_cache of size 232
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Reported-by: syzbot+174de899852504e4a74a@syzkaller.appspotmail.com
Reported-by: syzbot+3d1c772efafd3c38d007@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hillf Danton <hdanton@sina.com>
Link: https://lore.kernel.org/r/161234207610.653119.5287360098400436976.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68d54ceeec upstream.
The ptrace(PTRACE_PEEKMTETAGS) implementation checks whether the user
page has valid tags (mapped with PROT_MTE) by testing the PG_mte_tagged
page flag. If this bit is cleared, ptrace(PTRACE_PEEKMTETAGS) returns
-EIO.
A newly created (PROT_MTE) mapping points to the zero page which had its
tags zeroed during cpu_enable_mte(). If there were no prior writes to
this mapping, ptrace(PTRACE_PEEKMTETAGS) fails with -EIO since the zero
page does not have the PG_mte_tagged flag set.
Set PG_mte_tagged on the zero page when its tags are cleared during
boot. In addition, to avoid ptrace(PTRACE_PEEKMTETAGS) succeeding on
!PROT_MTE mappings pointing to the zero page, change the
__access_remote_tags() check to (vm_flags & VM_MTE) instead of
PG_mte_tagged.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 34bfeea4a9 ("arm64: mte: Clear the tags when a page is mapped in user-space with PROT_MTE")
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: Will Deacon <will@kernel.org>
Reported-by: Luis Machado <luis.machado@linaro.org>
Tested-by: Luis Machado <luis.machado@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210210180316.23654-1-catalin.marinas@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70245f86c1 upstream.
Invoking x86_init.irqs.create_pci_msi_domain() before
x86_init.pci.arch_init() breaks XEN PV.
The XEN_PV specific pci.arch_init() function overrides the default
create_pci_msi_domain() which is obviously too late.
As a consequence the XEN PV PCI/MSI allocation goes through the native
path which runs out of vectors and causes malfunction.
Invoke it after x86_init.pci.arch_init().
Fixes: 6b15ffa07d ("x86/irq: Initialize PCI/MSI domain at PCI init time")
Reported-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87pn18djte.fsf@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d6a3d3a2a ]
The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a155216c4 ]
As it turns out, vendor HDMI PHY driver for H6 has a pretty big table
of predefined values for various pixel clocks. However, most of them are
not useful/tested because they come from reference driver code. Vendor
PHY driver is concerned with only few of those, namely 27 MHz, 74.25
MHz, 148.5 MHz, 297 MHz and 594 MHz. These are all frequencies for
standard CEA modes.
Fix sun50i_h6_cur_ctr and sun50i_h6_phy_config with the values only for
aforementioned frequencies.
Table sun50i_h6_mpll_cfg doesn't need to be changed because values are
actually frequency dependent and not so much SoC dependent. See i.MX6
documentation for explanation of those values for similar PHY.
Fixes: c71c9b2fee ("drm/sun4i: Add support for Synopsys HDMI PHY")
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-5-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50791f5d7b ]
Channel 1 has polarity bits for vsync and hsync signals but driver never
sets them. It turns out that with pre-HDMI2 controllers seemingly there
is no issue if polarity is not set. However, with HDMI2 controllers
(H6) there often comes to de-synchronization due to phase shift. This
causes flickering screen. It's safe to assume that similar issues might
happen also with pre-HDMI2 controllers.
Solve issue with setting vsync and hsync polarity. Note that display
stacks with tcon top have polarity bits actually in tcon0 polarity
register.
Fixes: 9026e0d122 ("drm: Add Allwinner A10 Display Engine support")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209175900.7092-3-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 793f49a87a ]
arm64 references the start address of .builtin_fw (__start_builtin_fw)
with a pair of R_AARCH64_ADR_PREL_PG_HI21/R_AARCH64_LDST64_ABS_LO12_NC
relocations. The compiler is allowed to emit the
R_AARCH64_LDST64_ABS_LO12_NC relocation because struct builtin_fw in
include/linux/firmware.h is 8-byte aligned.
The R_AARCH64_LDST64_ABS_LO12_NC relocation requires the address to be a
multiple of 8, which may not be the case if .builtin_fw is empty.
Unconditionally align .builtin_fw to fix the linker error. 32-bit
architectures could use ALIGN(4) but that would add unnecessary
complexity, so just use ALIGN(8).
Link: https://lkml.kernel.org/r/20201208054646.2913063-1-maskray@google.com
Link: https://github.com/ClangBuiltLinux/linux/issues/1204
Fixes: 5658c76 ("firmware: allow firmware files to be built into kernel image")
Signed-off-by: Fangrui Song <maskray@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 532cfc0df1 ]
The index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this index before using it in hclge_get_rss_key().
Fixes: a638b1d8cc ("net: hns3: fix get VF RSS issue")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 326334aad0 ]
The tqp_index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this tqp_index before using it in hclge_get_ring_chain_from_mbx().
Fixes: 84e095d64e ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67a69f84ca ]
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes: 1a426f8b40 ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb4733d7cf ]
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07998281c2 ]
The origin skip check needs to re-test the zone. Else, we might skip
a colliding tuple in the reply direction.
This only occurs when using 'directional zones' where origin tuples
reside in different zones but the reply tuples share the same zone.
This causes the new conntrack entry to be dropped at confirmation time
because NAT clash resolution was elided.
Fixes: 4e35c1cb94 ("netfilter: nf_nat: skip nat clash resolution for same-origin entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef66a1eace ]
Normally we clear the failover_pending flag when processing the reset.
But if we are unable to schedule a failover reset we must clear the
flag ourselves. We could fail to schedule the reset if we are in PROBING
state (eg: when booting via kexec) or because we could not allocate memory.
Thanks to Cris Forno for helping isolate the problem and for testing.
Fixes: 1d85049374 ("powerpc/vnic: Extend "failover pending" window")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Tested-by: Cristobal Forno <cforno12@linux.ibm.com>
Link: https://lore.kernel.org/r/20210203050802.680772-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07bf34a50e ]
Michael tried to enable Advanced Error Reporting through the ENETC's
Root Complex Event Collector, and the system started spitting out single
bit correctable ECC errors coming from the ENETC interfaces:
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
fsl_enetc 0000:00:00.0: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.0: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.0: [14] CorrIntErr
fsl_enetc 0000:00:00.1: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.1: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.1: [14] CorrIntErr
Further investigating the port correctable memory error detect register
(PCMEDR) shows that these AER errors have an associated SOURCE_ID of 6
(RFS/RSS):
$ devmem 0x1f8010e10 32
0xC0000006
$ devmem 0x1f8050e10 32
0xC0000006
Discussion with the hardware design engineers reveals that on LS1028A,
the hardware does not do initialization of that RFS/RSS memory, and that
software should clear/initialize the entire table before starting to
operate. That comes as a bit of a surprise, since the driver does not do
initialization of the RFS memory. Also, the initialization of the
Receive Side Scaling is done only partially.
Even though the entire ENETC IP has a single shared flow steering
memory, the flow steering service should returns matches only for TCAM
entries that are within the range of the Station Interface that is doing
the search. Therefore, it should be sufficient for a Station Interface
to initialize all of its own entries in order to avoid any ECC errors,
and only the Station Interfaces in use should need initialization.
There are Physical Station Interfaces associated with PCIe PFs and
Virtual Station Interfaces associated with PCIe VFs. We let the PF
driver initialize the entire port's memory, which includes the RFS
entries which are going to be used by the VF.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210204134511.2640309-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d6bca156e ]
When updating the tcp or udp header checksum on port nat the function
inet_proto_csum_replace2 with the last parameter pseudohdr as true.
This leads to an error in the case that GRO is used and packets are
split up in GSO. The tcp or udp checksum of all packets is incorrect.
The error is probably masked due to the fact the most network driver
implement tcp/udp checksum offloading. It also only happens when GRO is
applied and not on single packets.
The error is most visible when using a pppoe connection which is not
triggering the tcp/udp checksum offload.
Fixes: ac2a66665e ("netfilter: add generic flow table infrastructure")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 767d1216bf ]
Although hooks are released via call_rcu(), chain and rule objects are
immediately released while packets are still walking over these bits.
This patch adds the .pre_exit callback which is invoked before
synchronize_rcu() in the netns framework to stay safe.
Remove a comment which is not valid anymore since the core does not use
synchronize_net() anymore since 8c873e2199 ("netfilter: core: free
hooks with call_rcu").
Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: df05ef874b ("netfilter: nf_tables: release objects on netns destruction")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3005b0f83 ]
use date %Y instead of %G to read current year
Problem appeared when running lkp-tests on 01/01/2021
Fixes: 48d072c4e8 ("selftests: netfilter: add time counter check")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
