[ Upstream commit 5ecae9f8c7 ]
For updating the IOC firmware's timestamp with system timestamp, the driver
issues the Mpi26IoUnitControlRequest message. While framing the
Mpi26IoUnitControlRequest, the driver should copy the lower 32 bits of the
current timestamp into IOCParameterValue field and the higher 32 bits into
Reserved7 field.
Link: https://lore.kernel.org/r/20211117123215.25487-1-sreekanth.reddy@broadcom.com
Fixes: f98790c003 ("scsi: mpt3sas: Sync time periodically between driver and firmware")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91202a01a2 ]
While determining the SAS address of a drive, the driver checks whether the
handle number is less than the HBA phy count or not. If the handle number
is less than the HBA phy count then driver assumes that this handle belongs
to HBA and hence it assigns the HBA SAS address.
During IOC firmware downgrade operation, if the number of HBA phys is
reduced and the OS drive's device handle drops below the phy count while
determining the drive's SAS address, the driver ends up using the HBA's SAS
address. This leads to a mismatch of drive's SAS address and hence the
driver unregisters the OS drive and the system goes into read-only mode.
Update the IOC's num_phys to the HBA phy count provided by actual loaded
firmware.
Link: https://lore.kernel.org/r/20211117105058.3505-1-sreekanth.reddy@broadcom.com
Fixes: a5e99fda01 ("scsi: mpt3sas: Update hba_port objects after host reset")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ee4ba13e0 ]
While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.
Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.
Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c45824ad ]
The failure to retrieve post-op attributes has no bearing on whether or
not the clone operation itself was successful. We must therefore ignore
the return value of decode_getfattr() when looking at the success or
failure of nfs4_xdr_dec_clone().
Fixes: 36022770de ("nfs42: add CLONE xdr functions")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1cbd9e0f7 ]
According to scmi specification, the response of the discover agent request
is made of:
- int32 status
- uint32 agent_id
- uint8 name[16]
but the current implementation doesn't take into account the agent_id field
and only allocates a rx buffer of SCMI_MAX_STR_SIZE length
Allocate the correct length for rx buffer and copy the name from the
correct offset in the response.
While no error were returned until v5.15, v5.16-rc1 fails with virtio_scmi
transport channel:
| arm-scmi firmware:scmi0: SCMI Notifications - Core Enabled.
| arm-scmi firmware:scmi0: SCMI Protocol v2.0 'Linaro:PMWG' Firmware version 0x2090000
| scmi-virtio virtio0: tx:used len 28 is larger than in buflen 24
Link: https://lore.kernel.org/r/20211117081856.9932-1-vincent.guittot@linaro.org
Fixes: b6f20ff8bd ("firmware: arm_scmi: add common infrastructure and support for base protocol")
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 451dc48c80 ]
This patch fixes an issue that an u32 netlink value is handled as a
signed enum value which doesn't fit into the range of u32 netlink type.
If it's handled as -1 value some BIT() evaluation ends in a
shift-out-of-bounds issue. To solve the issue we set the to u32 max which
is s32 "-1" value to keep backwards compatibility and let the followed enum
values start counting at 0. This brings the compiler to never handle the
enum as signed and a check if the value is above NL802154_IFTYPE_MAX should
filter -1 out.
Fixes: f3ea5e4423 ("ieee802154: add new interface command")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20211112030916.685793-1-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea157c2ba8 ]
Interrupt Clear registers WCD938X_INTR_CLEAR_0 - WCD938X_INTR_CLEAR_2
are not marked as volatile. This has resulted in a missing interrupt bug
while performing runtime pm. regcache_sync() during runtime pm resume path
will write to Interrupt clear registers with previous values which basically
clears the pending interrupt and actual interrupt handler never sees this
interrupt.
This issue is more visible with headset plug-in plug-out case compared to
headset button.
Fix this by adding the Interrupt clear registers to volatile range
Fixes: 8d78602aa8 ("ASoC: codecs: wcd938x: add basic driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211116114623.11891-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861afeac79 ]
Stream IDs are reused across multiple BackEnd mixers, do not reset the
stream mixers if they are not already set for that particular FrontEnd.
Ex:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
would set the MultiMedia1 steam for SLIMBUS_0_RX, however doing below
command will reset previously setup MultiMedia1 stream, because both of them
are using MultiMedia1 PCM stream.
amixer cset iface=MIXER,name='SLIMBUS_2_RX Audio Mixer MultiMedia1' 0
reset the FrontEnd Mixers conditionally to fix this issue.
This is more noticeable in desktop setup, where in alsactl tries to restore
the alsa state and overwriting the previous mixer settings.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211116114721.12517-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98481f3d72 ]
The PCIe host bridge has two interrupt lines, one that goes towards it
PCIE_INTR2 second level interrupt controller and one for its MSI second
level interrupt controller. The first interrupt line is not currently
managed by the driver, which is why it was not a functional problem.
The interrupt-map property was also only listing the PCI_INTA interrupts
when there are also the INTB, C and D.
Reported-by: Jim Quinlan <jim2101024@gmail.com>
Fixes: d5c8dc0d4c ("ARM: dts: bcm2711: Enable PCIe controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40f7342f05 ]
The GPIO controller is also an interrupt controller provider and is
currently missing the appropriate 'interrupt-controller' and
'#interrupt-cells' properties to denote that.
Fixes: fb026d3de3 ("ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 754c4050a0 ]
The I2C interrupt controller line is off by 32 because the datasheet
describes interrupt inputs into the GIC which are for Shared Peripheral
Interrupts and are starting at offset 32. The ARM GIC binding expects
the SPI interrupts to be numbered from 0 relative to the SPI base.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 678d92b612 ]
My previous bugfix addressed an API inconsistency found by syzbot,
and it correctly fixed the issue on x86-64 machines, which now behave
correctly for both native and compat tasks.
Unfortunately, John found that the patch broke compat mode on all other
architectures, as they can no longer rely on the VIDIOC_DQEVENT_TIME32
code from the native handler as a fallback in the compat code.
The best way I can see for addressing this is to generalize the
VIDIOC_DQEVENT32_TIME32 code from x86 and use that for all architectures,
leaving only the VIDIOC_DQEVENT32 variant as x86 specific. The original
code was trying to be clever and use the same conversion helper for native
32-bit code and compat mode, but that turned out to be too obscure so
even I missed that bit I had introduced myself when I made the fix.
Fixes: c344f07aa1 ("media: v4l2-core: ignore native time32 ioctls on 64-bit")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f6eed4cb ]
Previously the IPv6 addresses in the key were clobbered and the mask was
left unset.
I haven't tested this; I noticed it while skimming the code to
understand an unrelated issue.
Fixes: cfab6dbd0e ("netfilter: flowtable: add tunnel match offload support")
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: Will Mortensen <willmo@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c95c07836f ]
We are changing expire_nodest_conn to work even for reused connections when
conn_reuse_mode=0, just as what was done with commit dc7b3eb900 ("ipvs:
Fix reuse connection if real server is dead").
For controlled and persistent connections, the new connection will get the
needed real server depending on the rules in ip_vs_check_template().
Fixes: d752c36457 ("ipvs: allow rescheduling of new connections when port reuse is detected")
Co-developed-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77522ff02f ]
And be consistent in error management for both orig/reply filtering
Fixes: cb8aa9a3af ("netfilter: ctnetlink: add kernel side filtering for dump")
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd572393ba ]
If codec is in runtime suspend, but controller is not, hotplug events
are missed as the codec has no way to alert the controller. Problem does
not occur if both controller and codec are active, or when both are
suspended.
An easy way to reproduce is to play an audio stream on one codec (e.g.
to HDMI/DP display codec), wait for other HDA codec to go to runtime
suspend, and then plug in a headset to the suspended codec. The jack
event is not reported correctly in this case. Another way to reproduce
is to force controller to stay active with
"snd_sof_pci.sof_pci_debug=0x1"
Fix the issue by reconfiguring the WAKEEN register when powering up/down
individual links, and handling control events in the interrupt handler.
Fixes: 87fc20e4a0 ("ASoC: SOF: Intel: hda: use hdac_ext fine-grained link management")
Reported-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211105111655.668777-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c1e6311771 upstream.
To clear a user buffer we cannot simply use memset, we have to use
clear_user(). With a virtio-mem device that registers a vmcore_cb and
has some logically unplugged memory inside an added Linux memory block,
I can easily trigger a BUG by copying the vmcore via "cp":
systemd[1]: Starting Kdump Vmcore Save Service...
kdump[420]: Kdump is using the default log level(3).
kdump[453]: saving to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/
kdump[458]: saving vmcore-dmesg.txt to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/
kdump[465]: saving vmcore-dmesg.txt complete
kdump[467]: saving vmcore
BUG: unable to handle page fault for address: 00007f2374e01000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
PGD 7a523067 P4D 7a523067 PUD 7a528067 PMD 7a525067 PTE 800000007048f867
Oops: 0003 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 468 Comm: cp Not tainted 5.15.0+ #6
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-27-g64f37cc530f1-prebuilt.qemu.org 04/01/2014
RIP: 0010:read_from_oldmem.part.0.cold+0x1d/0x86
Code: ff ff ff e8 05 ff fe ff e9 b9 e9 7f ff 48 89 de 48 c7 c7 38 3b 60 82 e8 f1 fe fe ff 83 fd 08 72 3c 49 8d 7d 08 4c 89 e9 89 e8 <49> c7 45 00 00 00 00 00 49 c7 44 05 f8 00 00 00 00 48 83 e7 f81
RSP: 0018:ffffc9000073be08 EFLAGS: 00010212
RAX: 0000000000001000 RBX: 00000000002fd000 RCX: 00007f2374e01000
RDX: 0000000000000001 RSI: 00000000ffffdfff RDI: 00007f2374e01008
RBP: 0000000000001000 R08: 0000000000000000 R09: ffffc9000073bc50
R10: ffffc9000073bc48 R11: ffffffff829461a8 R12: 000000000000f000
R13: 00007f2374e01000 R14: 0000000000000000 R15: ffff88807bd421e8
FS: 00007f2374e12140(0000) GS:ffff88807f000000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2374e01000 CR3: 000000007a4aa000 CR4: 0000000000350eb0
Call Trace:
read_vmcore+0x236/0x2c0
proc_reg_read+0x55/0xa0
vfs_read+0x95/0x190
ksys_read+0x4f/0xc0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Some x86-64 CPUs have a CPU feature called "Supervisor Mode Access
Prevention (SMAP)", which is used to detect wrong access from the kernel
to user buffers like this: SMAP triggers a permissions violation on
wrong access. In the x86-64 variant of clear_user(), SMAP is properly
handled via clac()+stac().
To fix, properly use clear_user() when we're dealing with a user buffer.
Link: https://lkml.kernel.org/r/20211112092750.6921-1-david@redhat.com
Fixes: 997c136f51 ("fs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages")
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Philipp Rudo <prudo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f76b36d40b upstream.
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbff ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851d ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223dec14a0 upstream.
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") fixed
handling of CRS response and when CRSSVE flag was not enabled it marked CRS
response as failed transaction (due to simplicity).
But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count
for PIO config response and so we can with a small change implement
re-issuing of config requests as described in PCIe base specification.
This change implements re-issuing of config requests when response is CRS.
Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the
transaction is marked as failed and an all-ones value is returned as
before.
We do this by returning appropriate error codes from function
advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then
reissues transaction.
Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f015d89a4 upstream.
The mechanism in use to allow the client to see the results of COPY/CLONE
is to drop those pages from the pagecache. This forces the client to read
those pages once more from the server. However, truncate_pagecache_range()
zeros out partial pages instead of dropping them. Let us instead use
invalidate_inode_pages2_range() with full-page offsets to ensure the client
properly sees the results of COPY/CLONE operations.
Cc: <stable@vger.kernel.org> # v4.7+
Fixes: 2e72448b07 ("NFS: Add COPY nfs operation")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8af404ffc upstream.
Before commit 740499c784 ("iomap: fix the iomap_readpage_actor return
value for inline data"), when hitting an IOMAP_INLINE extent,
iomap_readpage_actor would report having read the entire page. Since
then, it only reports having read the inline data (iomap->length).
This will force iomap_readpage into another iteration, and the
filesystem will report an unaligned hole after the IOMAP_INLINE extent.
But iomap_readpage_actor (now iomap_readpage_iter) isn't prepared to
deal with unaligned extents, it will get things wrong on filesystems
with a block size smaller than the page size, and we'll eventually run
into the following warning in iomap_iter_advance:
WARN_ON_ONCE(iter->processed > iomap_length(iter));
Fix that by changing iomap_readpage_iter to return 0 when hitting an
inline extent; this will cause iomap_iter to stop immediately.
To fix readahead as well, change iomap_readahead_iter to pass on
iomap_readpage_iter return values less than or equal to zero.
Fixes: 740499c784 ("iomap: fix the iomap_readpage_actor return value for inline data")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3eb70ead6 upstream.
trans_pgd_create_copy() can hit "VM_BUG_ON(mm != &init_mm)" in the
function pmd_populate_kernel().
This is the combined consequence of commit 5de59884ac ("arm64:
trans_pgd: pass NULL instead of init_mm to *_populate functions"), which
replaced &init_mm with NULL and commit 59511cfd08 ("arm64: mm: use XN
table mapping attributes for user/kernel mappings"), which introduced
the VM_BUG_ON.
Since the former sounds reasonable, it is better to work on the later.
From the perspective of trans_pgd, two groups of functions are
considered in the later one:
pmd_populate_kernel()
mm == NULL should be fixed, else it hits VM_BUG_ON()
p?d_populate()
mm == NULL means PXN, that is OK, since trans_pgd only copies a
linear map, no execution will happen on the map.
So it is good enough to just relax VM_BUG_ON() to disregard mm == NULL
Fixes: 59511cfd08 ("arm64: mm: use XN table mapping attributes for user/kernel mappings")
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Cc: <stable@vger.kernel.org> # 5.13.x
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/r/20211112052214.9086-1-kernelfans@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a55f224ff5 upstream.
If a event is filtered by pid and a trigger that requires processing of
the event to happen is a attached to the event, the discard portion does
not take the pid filtering into account, and the event will then be
recorded when it should not have been.
Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf0b0e3712 upstream.
The POWER9 ERAT flush instruction is a SLBIA with IH=7, which is a
reserved value on POWER7/8. On POWER8 this invalidates the SLB entries
above index 0, similarly to SLBIA IH=0.
If the SLB entries are invalidated, and then the guest is bypassed, the
host SLB does not get re-loaded, so the bolted entries above 0 will be
lost. This can result in kernel stack access causing a SLB fault.
Kernel stack access causing a SLB fault was responsible for the infamous
mega bug (search "Fix SLB reload bug"). Although since commit
48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C") that
starts using the kernel stack in the SLB miss handler, it might only
result in an infinite loop of SLB faults. In any case it's a bug.
Fix this by only executing the instruction on >= POWER9 where IH=7 is
defined not to invalidate the SLB. POWER7/8 don't require this ERAT
flush.
Fixes: 5008711259 ("KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211119031627.577853-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ec72153ff upstream.
If xattr is not supported like exfat or fat, ksmbd server doesn't
contain default data stream in FILE_STREAM_INFORMATION response. It will
cause ppt or doc file update issue if local filesystem is such as ones.
This patch move goto statement to contain it.
Fixes: 9f6323311c ("ksmbd: add default data stream name in FILE_STREAM_INFORMATION")
Cc: stable@vger.kernel.org # v5.15
Acked-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e537d1465 upstream.
While file transfer through windows client, This error flood message
happen. This flood message will cause performance degradation and
misunderstand server has problem.
Fixes: e294f78d34 ("ksmbd: allow PROTECTED_DACL_SECINFO and UNPROTECTED_DACL_SECINFO addition information in smb2 set info security")
Cc: stable@vger.kernel.org # v5.15
Acked-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
