[ Upstream commit 820830ec91 ]
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a5fe2fb96 ]
When BCM47XX_BCMA is enabled and BCMA_DRIVER_PCI is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for BCMA_DRIVER_PCI_HOSTMODE
Depends on [n]: MIPS [=y] && BCMA_DRIVER_PCI [=n] && PCI_DRIVERS_LEGACY [=y] && BCMA [=y]=y
Selected by [y]:
- BCM47XX_BCMA [=y] && BCM47XX [=y] && PCI [=y]
The reason is that BCM47XX_BCMA selects BCMA_DRIVER_PCI_HOSTMODE without
depending on or selecting BCMA_DRIVER_PCI while BCMA_DRIVER_PCI_HOSTMODE
depends on BCMA_DRIVER_PCI. This can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: c1d1c5d421 ("bcm47xx: add support for bcma bus")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209879
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb7dc5db6 ]
gcc points out a suspicious mixing of enum types in a function that
converts from MTHCA_OPCODE_* values to IB_WC_* values:
drivers/infiniband/hw/mthca/mthca_cq.c: In function 'mthca_poll_one':
drivers/infiniband/hw/mthca/mthca_cq.c:607:21: warning: implicit conversion from 'enum <anonymous>' to 'enum ib_wc_opcode' [-Wenum-conversion]
607 | entry->opcode = MTHCA_OPCODE_INVALID;
Nothing seems to ever check for MTHCA_OPCODE_INVALID again, no idea if
this is meaningful, but it seems harmless as it deals with an invalid
input.
Remove MTHCA_OPCODE_INVALID and set the ib_wc_opcode to 0xFF, which is
still bogus, but at least doesn't make compiler warnings.
Fixes: 2a4443a699 ("[PATCH] IB/mthca: fill in opcode field for send completions")
Link: https://lore.kernel.org/r/20201026211311.3887003-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dfccd13db ]
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
Fixes: d5e911928b ("Bluetooth: AMP: Process Physical Link Complete evt")
Reported-and-tested-by: syzbot+0bef568258653cff272f@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=0bef568258653cff272f
Signed-off-by: Anmol Karn <anmol.karan123@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e47fbca6 ]
It's not possible to reboot or poweroff Exynos7420 using PSCI. Instead
we need to use syscon reboot/poweroff drivers, like it's done for other
Exynos SoCs. This was confirmed by checking vendor source and testing it
on Samsung Galaxy S6 device based on this SoC.
To be able to use custom restart/poweroff handlers instead of PSCI
functions, we need to correct psci compatible. This also requires us to
provide function ids for CPU_ON and CPU_OFF.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-2-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c22b80f61 ]
soc-pcm's dpcm_fe_dai_do_trigger() supported DRAIN commnad up to kernel
v5.4 where explicit switch(cmd) has been introduced which takes into
account all SNDRV_PCM_TRIGGER_xxx but SNDRV_PCM_TRIGGER_DRAIN. Update
switch statement to reactive support for it.
As DRAIN is somewhat unique by lacking negative/stop counterpart, bring
behaviour of dpcm_fe_dai_do_trigger() for said command back to its
pre-v5.4 state by adding it to START/RESUME/PAUSE_RELEASE group.
Fixes: acbf27746e ("ASoC: pcm: update FE/BE trigger order based on the command")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201026100129.8216-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0237616173 ]
current_desc_hdr() returns a u32 but in fact this is a __be32,
leading to a lot of sparse warnings.
Change the return type to __be32 and ensure it is handled as
sure by the caller.
Fixes: 3e721aeb3d ("crypto: talitos - handle descriptor not found in error path")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e79f0211b ]
When running in BE mode on LPAE hardware with a PA-to-VA translation
that exceeds 4 GB, we patch bits 39:32 of the offset into the wrong
byte of the opcode. So fix that, by rotating the offset in r0 to the
right by 8 bits, which will put the 8-bit immediate in bits 31:24.
Note that this will also move bit #22 in its correct place when
applying the rotation to the constant #0x400000.
Fixes: d9a790df8e ("ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE")
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb3ab2979f ]
The code which limited the number of unacknowledged PSNs was incorrect.
The PSNs are limited to 24 bits and wrap back to zero from 0x00ffffff.
The test was computing a 32 bit value which wraps at 32 bits so that
qp->req.psn can appear smaller than the limit when it is actually larger.
Replace '>' test with psn_compare which is used for other PSN comparisons
and correctly handles the 24 bit size.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20201013170741.3590-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e19d51ca5 ]
clang static analysis reports this problem:
cdv_intel_dp.c:2101:2: warning: Attempt to free released memory
kfree(gma_connector);
^~~~~~~~~~~~~~~~~~~~
In cdv_intel_dp_init() when the call to cdv_intel_edp_panel_vdd_off()
fails, the handler calls cdv_intel_dp_destroy(connector) which does
the first free of gma_connector. So adjust the goto label and skip
the second free.
Fixes: d112a8163f ("gma500/cdv: Add eDP support")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003193928.18869-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2f70e49ed8 upstream.
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd7e7ff56f upstream.
On Odroid XU LDO12 and LDO15 supplies the power to USB 3.0 blocks but
the GPK GPIO pins are supplied by LDO7 (VDDQ_LCD). LDO7 also supplies
GPJ GPIO pins.
The Exynos pinctrl driver does not take any supplies, so to have entire
GPIO block always available, make the regulator always on.
Fixes: 88644b4c75 ("ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-3-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d992fd8f4 upstream.
The VBUS control (PWREN) and over-current pins of USB 3.0 DWC3
controllers are on Exynos5410 regular GPIOs. This is different than for
example on Exynos5422 where these are special ETC pins with proper reset
values (pulls, functions).
Therefore these pins should be configured to enable proper USB 3.0
peripheral and host modes. This also fixes over-current warning:
[ 6.024658] usb usb4-port1: over-current condition
[ 6.028271] usb usb3-port1: over-current condition
Fixes: cb08965622 ("ARM: dts: exynos: Add USB to Exynos5410")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-2-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a353397b0d upstream.
In many cases a function that supports SuperSpeed can very well
operate in SuperSpeedPlus, if a gadget controller supports it,
as the endpoint descriptors (and companion descriptors) are
generally identical and can be re-used. This is true for two
commonly used functions: Android's ADB and MTP. So we can simply
assign the usb_function's ssp_descriptors array to point to its
ss_descriptors, if available. Similarly, we need to allow an
epfile's ioctl for FUNCTIONFS_ENDPOINT_DESC to correctly
return the corresponding SuperSpeed endpoint descriptor in case
the connected speed is SuperSpeedPlus as well.
The only exception is if a function wants to implement an
Isochronous endpoint capable of transferring more than 48KB per
service interval when operating at greater than USB 3.1 Gen1
speed, in which case it would require an additional SuperSpeedPlus
Isochronous Endpoint Companion descriptor to be returned as part
of the Configuration Descriptor. Support for that would need
to be separately added to the userspace-facing FunctionFS API
which may not be a trivial task--likely a new descriptor format
(v3?) may need to be devised to allow for separate SS and SSP
descriptors to be supplied.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201027230731.9073-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e7b624183d ]
The BUG_ON(in_interrupt()) in dm_table_event() is a historic leftover from
a rework of the dm table code which changed the calling context.
Issuing a BUG for a wrong calling context is frowned upon and
in_interrupt() is deprecated and only covering parts of the wrong
contexts. The sanity check for the context is covered by
CONFIG_DEBUG_ATOMIC_SLEEP and other debug facilities already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b74e40a4e ]
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa86fc2e2 ]
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d96f04d347 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 862ee699fe upstream.
The console part of sisusbvga is broken vs. printk(). It uses in_atomic()
to detect contexts in which it cannot sleep despite the big fat comment in
preempt.h which says: Do not use in_atomic() in driver code.
in_atomic() does not work on kernels with CONFIG_PREEMPT_COUNT=n which
means that spin/rw_lock held regions are not detected by it.
There is no way to make this work by handing context information through to
the driver and this only can be solved once the core printk infrastructure
supports sleepable console drivers.
Make it depend on BROKEN for now.
Fixes: 1bbb4f2035 ("[PATCH] USB: sisusb[vga] update")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101109.603244207@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dde8ffd0 upstream.
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
