Simon Horman says:
====================
*nfp: VF rate limit support
this short series adds VF rate limiting to the NFP driver.
The first patch, as suggested by Jakub Kicinski, adds a helper
to check that ndo_set_vf_rate() rate parameters are sane.
It also provides a place for further parameter checking to live,
if needed in future.
The second patch adds VF rate limit support to the NFP driver.
It addresses several comments made on v1, including removing
the parameter check that is now provided by the helper added
in the first patch.
====================
Link: https://lore.kernel.org/r/20220511113932.92114-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add VF rate limit feature
This patch enhances the NFP driver to supports assignment of
both max_tx_rate and min_tx_rate to VFs
The template of configurations below is all supported.
e.g.
# ip link set $DEV vf $VF_NUM max_tx_rate $RATE_VALUE
# ip link set $DEV vf $VF_NUM min_tx_rate $RATE_VALUE
# ip link set $DEV vf $VF_NUM max_tx_rate $RATE_VALUE \
min_tx_rate $RATE_VALUE
# ip link set $DEV vf $VF_NUM min_tx_rate $RATE_VALUE \
max_tx_rate $RATE_VALUE
The max RATE_VALUE is limited to 0xFFFF which is about
63Gbps (using 1024 for 1G)
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When calling ndo_set_vf_rate() the max_tx_rate parameter may be zero,
in which case the setting is cleared, or it must be greater or equal to
min_tx_rate.
Enforce this requirement on all calls to ndo_set_vf_rate via a wrapper
which also only calls ndo_set_vf_rate() if defined by the driver.
Based on work by Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Right now, a PHY-less port (no phy-mode, no fixed-link, no phy-handle)
doesn't register with phylink, but calls netif_carrier_on() from
enetc_start().
This makes sense for a VF, but for a PF, this is braindead, because we
never call enetc_mac_enable() so the MAC is left inoperational.
Furthermore, commit 71b77a7a27 ("enetc: Migrate to PHYLINK and
PCS_LYNX") put the nail in the coffin because it removed the initial
netif_carrier_off() call done right after register_netdev().
Without that call, netif_carrier_on() does not call
linkwatch_fire_event(), so the operstate remains IF_OPER_UNKNOWN.
Just deny the broken configuration by requiring that a phy-mode is
present, and always register a PF with phylink.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220511094200.558502-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Vladimir Oltean says:
====================
Count tc-taprio window drops in enetc driver
This series includes a patch from Po Liu (no longer with NXP) which
counts frames dropped by the tc-taprio offload in ethtool -S and in
ndo_get_stats64. It also contains a preparation patch from myself.
====================
Link: https://lore.kernel.org/r/20220510163615.6096-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enetc scheduler for IEEE 802.1Qbv has 2 options (depending on
PTGCR[TG_DROP_DISABLE]) when we attempt to send an oversized packet
which will never fit in its allotted time slot for its traffic class:
either block the entire port due to head-of-line blocking, or drop the
packet and set a bit in the writeback format of the transmit buffer
descriptor, allowing other packets to be sent.
We obviously choose the second option in the driver, but we do not
detect the drop condition, so from the perspective of the network stack,
the packet is sent and no error counter is incremented.
This change checks the writeback of the TX BD when tc-taprio is enabled,
and increments a specific ethtool statistics counter and a generic
"tx_dropped" counter in ndo_get_stats64.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Future work in this driver would like to look at priv->active_offloads &
ENETC_F_QBV to determine whether a tc-taprio qdisc offload was
installed, but this does not produce the intended effect.
All the other flags in priv->active_offloads are managed dynamically,
except ENETC_F_QBV which is set statically based on the probed SI capability.
This change makes priv->active_offloads & ENETC_F_QBV really track the
presence of a tc-taprio schedule on the port.
Some existing users, like the enetc_sched_speed_set() call from
phylink_mac_link_up(), are best kept using the old logic: the tc-taprio
offload does not re-trigger another link mode resolve, so the scheduler
needs to be functional from the get go, as long as Qbv is supported at
all on the port. So to preserve functionality there, look at the static
station interface capability from pf->si->hw_features instead.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Robert Hancock says:
====================
MACB NAPI improvements
Simplify the logic in the Cadence MACB/GEM driver for determining
when to reschedule NAPI processing, and update it to use NAPI for the
TX path as well as the RX path.
Changes since v1: Changed to use separate TX and RX NAPI instances and
poll functions to avoid unnecessary checks of the other ring (TX/RX)
states during polling and to use budget handling for both RX and TX.
Fixed locking to protect against concurrent access to TX ring on
TX transmit and TX poll paths.
====================
Link: https://lore.kernel.org/r/20220509194635.3094080-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver was using the TX IRQ handler to perform all TX completion
tasks. Under heavy TX network load, this can cause significant irqs-off
latencies (found to be in the hundreds of microseconds using ftrace).
This can cause other issues, such as overrunning serial UART FIFOs when
using high baud rates with limited UART FIFO sizes.
Switch to using a NAPI poll handler to perform the TX completion work
to get this out of hard IRQ context and avoid the IRQ latency impact. A
separate NAPI instance is used for TX and RX to avoid checking the other
ring's state unnecessarily when doing the poll, and so that the NAPI
budget handling can work for both TX and RX packets.
A new per-queue tx_ptr_lock spinlock has been added to avoid using the
main device lock (with IRQs needing to be disabled) across the entire TX
mapping operation, and also to protect the TX queue pointers from
concurrent access between the TX start and TX poll operations.
The TX Used Bit Read interrupt (TXUBR) handling also needs to be moved into
the TX NAPI poll handler to maintain the proper order of operations. A flag
is used to notify the poll handler that a UBR condition needs to be
handled. The macb_tx_restart handler has had some locking added for global
register access, since this could now potentially happen concurrently on
different queues.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously the macb_poll method was checking the RSR register after
completing its RX receive work to see if additional packets had been
received since IRQs were disabled, since this controller does not
maintain the pending IRQ status across IRQ disable. It also had to
double-check the register after re-enabling IRQs to detect if packets
were received after the first check but before IRQs were enabled.
Using the RSR register for this purpose is problematic since it reflects
the global device state rather than the per-queue state, so if packets
are being received on multiple queues it may end up retriggering receive
on a queue where the packets did not actually arrive and not on the one
where they did arrive. This will also cause problems with an upcoming
change to use NAPI for the TX path where use of multiple queues is more
likely.
Add a macb_rx_pending function to check the RX ring to see if more
packets have arrived in the queue, and use that to check if NAPI should
be rescheduled rather than the RSR register. By doing this, we can just
ignore the global RSR register entirely, and thus save some extra device
register accesses at the same time.
This also makes the previous first check for pending packets rather
redundant, since it would be checking the RX ring state which was just
checked in the receive work function. Therefore we can get rid of it and
just check after enabling interrupts whether packets are already
pending.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The host interfaces $h1 and $h2 don't have to be switchdev interfaces,
but due to the fact that we pass $tcflags which may have the value of
"skip_sw", we force $h2 to offload a drop rule for dst_ip, something
which it may not be able to do.
The selftest only wants to verify the hit count of this rule as a means
of figuring out whether the packet was received, so remove the $tcflags
for it and let it be done in software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220510220904.284552-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2022-05-10
This series contains updates to igc driver only.
Sasha cleans up the code by removing an unused function and removing an
enum for PHY type as there is only one PHY. The return type for
igc_check_downshift() is changed to void as it always returns success.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Change type of the 'igc_check_downshift' method
igc: Remove unused phy_type enum
igc: Remove igc_set_spd_dplx method
====================
Link: https://lore.kernel.org/r/20220510210656.2168393-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Looks like all the changes to this driver had been tree-wide
refactoring since git era begun. The driver is using virt_to_bus()
we should make it use more modern DMA APIs but since it's unlikely
to be getting any use these days delete it instead. We can always
revert to bring it back.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like all the changes to this driver had been tree-wide
refactoring since git era begun. The driver is using virt_to_bus()
we should make it use more modern DMA APIs but since it's unlikely
to be getting any use these days delete it instead. We can always
revert to bring it back.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: CONFIG_DEBUG_NET and friends
This patch series is inspired by some syzbot reports
hinting that skb transport_header might be not set
in places we expect it being set.
Add a new CONFIG_DEBUG_NET option
and DEBUG_NET_WARN_ON_ONCE() helper, so that we can start
adding more sanity checks in the future.
Replace two BUG() in skb_checksum_help()
with less risky code.
v2: make first patch compile on more arches/compilers
add the 5th patch to add more debugging in skb_checksum_help()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a followup of previous patch.
Dumping the stack trace is a good start, but printing
basic skb information is probably better.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a syzbot report that managed to get a crash in skb_checksum_help()
If syzbot can trigger these BUG(), it makes sense to replace
them with more friendly WARN_ON_ONCE() since skb_checksum_help()
can instead return an error code.
Note that syzbot will still crash there, until real bug is fixed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure skb_transport_header() and skb_transport_offset() uses
are not fooled if the transport header has not been set.
This change will likely expose existing bugs in linux networking stacks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This config option enables network debugging checks.
This patch adds DEBUG_NET_WARN_ON_ONCE(cond)
Note that this is not a replacement for WARN_ON_ONCE(cond)
as (cond) is not evaluated if CONFIG_DEBUG_NET is not set.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove from include/linux/netdevice.h helpers
that send debug/info/warnings to syslog.
We plan adding more helpers in following patches.
v2: added two includes, and 'struct net_device' forward declaration
to avoid compile errors (kernel bots)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2022-05-09
1) Gavin Li, adds exit route from waiting for FW init on device boot and
increases FW init timeout on health recovery flow
2) Support 4 ports HCAs LAG mode
Mark Bloch Says:
================
This series adds to mlx5 drivers support for 4 ports HCAs.
Starting with ConnectX-7 HCAs with 4 ports are possible.
As most driver parts aren't affected by such configuration most driver
code is unchanged.
Specially the only affected areas are:
- Lag
- Devcom
- Merged E-Switch
- Single FDB E-Switch
Lag was chosen to be converted first. Creating hardware LAG when all 4
ports are added to the same bond device.
Devom, merge E-Switch and single FDB E-Switch, are marked as supporting
only 2 ports HCAs and future patches will add support for 4 ports HCAs.
In order to activate the hardware lag a user can execute the:
ip link add bond0 type bond
ip link set bond0 type bond miimon 100 mode 2
ip link set eth2 master bond0
ip link set eth3 master bond0
ip link set eth4 master bond0
ip link set eth5 master bond0
Where eth2, eth3, eth4 and eth5 are the PFs of the same HCA.
================
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuiko Oshino says:
====================
net: phy: add comments for LAN8742 phy support
Add comments for 0xfffffff2 phy ID mask for the LAN8742 and the LAN88xx, explaining that they can coexist and allow future hardware revisions.
Also add one missing tab in smsc.c.
====================
Link: https://lore.kernel.org/r/20220509185804.7147-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
add comments for the LAN8742 phy ID mask in the previous patch.
add one missing tab in the LAN8742 phy ID line.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
add comments for the updated LAN88xx phy ID mask in the previous patch.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Long time ago Tom added a giant comment to skbuff.h explaining
checksums. Now that we have a place in Documentation for skbuff
docs we should render it. Sprinkle some markup while at it.
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The comment about shinfo->dataref split is really unhelpful,
at least to me. Rewrite it and render it to skb documentation.
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add basic skb documentation. It's mostly an intro to the subsequent
patches - it would looks strange if we documented advanced topics
without covering the basics in any way.
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin Habets says:
====================
Move Siena into a separate subdirectory
The Siena NICs (SFN5000 and SFN6000 series) went EOL in November 2021.
Most of these adapters have been remove from our test labs, and testing
has been reduced to a minimum.
This patch series creates a separate kernel module for the Siena architecture,
analogous to what was done for Falcon some years ago.
This reduces our maintenance for the sfc.ko module, and allows us to
enhance the EF10 and EF100 drivers without the risk of breaking Siena NICs.
After this series further enhancements are needed to differentiate the
new kernel module from sfc.ko, and the Siena code can be removed from sfc.ko.
Thes will be posted as a small follow-up series.
The Siena module is not built by default, but can be enabled
using Kconfig option SFC_SIENA. This will create module sfc-siena.ko.
Patches
Patches 1-3 establish the code base for the Siena driver.
Patches 4-10 ensure the allyesconfig build succeeds.
Patch 11 adds the basic Siena module.
I do not expect patch 1 through 3 to be reviewed, they are FYI only.
No checkpatch issues were resolved as part of these, but they
were fixed in the subsequent patches.
Testing
Various build tests were done such as allyesconfig, W=1 and sparse.
The new sfc-siena.ko and sfc.ko modules were tested on a machine with both
these NICs in them, and several tests were run on both drivers.
====================
Link: https://lore.kernel.org/r/165211018297.5289.9658523545298485394.stgit@palantir17.mph.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the (un)load message more specific to differentiate it from
the sfc.ko messages.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The implementation of each is quite short. This means sriov.c is
not needed any more.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For siena use efx_siena_ as the function prefix.
efx_nic_update_stats_atomic is only used in efx_common.c, so move
it there.
efx_nic_copy_stats is not used in Siena, so it is removed.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For siena use efx_siena_ as the function prefix.
Several functions are not used in Siena, so they are removed.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For siena use efx_siena_ as the function prefix.
This patch covers selftest.h, ptp.h, net_driver.h and ethtool_common.h.
efx_ethtool_fill_self_tests() can become static.
Some functions in ptp.c can also become static.
Rename loopback_mode in net_driver.h.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For siena use efx_siena_ as the function prefix.
Several functions are not used in Siena, so they are removed.
Use a Siena specific variable name for module parameter
efx_separate_tx_channels.
Move efx_fini_tx_queue() to avoid a forward declaration of
efx_dequeue_buffer().
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building with allyesconfig there are many identical
symbol names.
For siena use efx_siena_ as the function and variable prefix
to avoid build errors.
efx_mtd_remove_partition can become static as it is no longer called
from other files.
efx_ticks_to_usecs and efx_xmit_done_single are not used in Siena, so
they are removed.
Several functions are only used inside efx_channels.c for Siena so
they can become static.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Functionality not supported or needed on Siena includes:
- Anything for EF100
- EF10 specifics such as register access, PIO and TSO offload.
Also only bind to Siena NICs.
Remove EF10 specifics from nic.h.
The functions that start with efx_farch_ will be removed from sfc.ko
with a subsequent patch.
Add the efx_ prefix to siena_prepare_flush() to make it consistent
with the other APIs.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are the files starting with m through w.
No changes are done, those will be done with subsequent commits.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are the files starting with b through i.
No changes are done, those will be done with subsequent commits.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel test robot reported an issue after a recent patch about an
unused variable when CONFIG_IPV6 is disabled. Move the variable
declaration to be inside the #ifdef, and do a bit more cleanup. There
is no need to use a temporary ipv6 bool value, it is just checked once,
remove the extra variable and just do the check directly.
Fixes: 9d5447ed44 ("nfp: flower: fixup ipv6/ipv4 route lookup for neigh events")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220510074845.41457-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Complete to commit 8e153faf58 ("igc: Remove unused phy type")
i225 parts have only one PHY. There is no point to use phy_type enum.
Clean up the code accordingly, and get rid of the unused enum lines.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pointer dev is being assigned a value that is never used, the assignment
and the variable are redundant and can be removed. Also replace null check
with the preferred !ptr idiom.
Cleans up clang scan warning:
net/x25/x25_proc.c:94:26: warning: Although the value stored to 'dev' is
used in the enclosing expression, the value is never actually read
from 'dev' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220508214500.60446-1-colin.i.king@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
