[ Upstream commit 20730e9b277873deeb6637339edcba64468f3da3 ]
With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an
ASUSTeK Pro WS WRX80E-SAGE SE WIFI mainboard, a controller hang was
observed that was immediately preceded by the following kernel
messages:
ahci 0000:28:00.0: Using 64-bit DMA addresses
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00000 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00300 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00380 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00400 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00680 flags=0x0000]
ahci 0000:28:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0035 address=0x7fffff00700 flags=0x0000]
The first message is produced by code in drivers/iommu/dma-iommu.c
which is accompanied by the following comment that seems to apply:
/*
* Try to use all the 32-bit PCI addresses first. The original SAC vs.
* DAC reasoning loses relevance with PCIe, but enough hardware and
* firmware bugs are still lurking out there that it's safest not to
* venture into the 64-bit space until necessary.
*
* If your device goes wrong after seeing the notice then likely either
* its driver is not setting DMA masks accurately, the hardware has
* some inherent bug in handling >32-bit addresses, or not all the
* expected address bits are wired up between the device and the IOMMU.
*/
Asking the ASM1061 on a discrete PCIe card to DMA from I/O virtual
address 0xffffffff00000000 produces the following I/O page faults:
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000000 flags=0x0010]
vfio-pci 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0x7ff00000500 flags=0x0010]
Note that the upper 21 bits of the logged DMA address are zero. (When
asking a different PCIe device in the same PCIe slot to DMA to the
same I/O virtual address, we do see all the upper 32 bits of the DMA
address as 1, so this is not an issue with the chipset or IOMMU
configuration on the test system.)
Also, hacking libahci to always set the upper 21 bits of all DMA
addresses to 1 produces no discernible effect on the behavior of the
ASM1061, and mkfs/mount/scrub/etc work as without this hack.
This all strongly suggests that the ASM1061 has a 43 bit DMA address
limit, and this commit therefore adds a quirk to deal with this limit.
This issue probably applies to (some of) the other supported ASMedia
parts as well, but we limit it to the PCI IDs known to refer to
ASM1061 parts, as that's the only part we know for sure to be affected
by this issue at this point.
Link: https://lore.kernel.org/linux-ide/ZaZ2PIpEId-rl6jv@wantstofly.org/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: drop date from error messages in commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0077a504e1a4468669fd2e011108db49133db56e ]
The ASM1166 SATA host controller always reports wrongly,
that it has 32 ports. But in reality, it only has six ports.
This seems to be a hardware issue, as all tested ASM1166
SATA host controllers reports such high count of ports.
Example output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0xffffff3f impl SATA mode.
By adjusting the port_map, the count is limited to six ports.
New output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0x3f impl SATA mode.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=211873
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218346
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de8b6e1c231a95abf95ad097b993d34b31458ec9 ]
Return IRQ_NONE from the interrupt handler when no interrupt was
detected. Because an empty interrupt will cause a null pointer error:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000008
Call trace:
complete+0x54/0x100
hisi_sfc_v3xx_isr+0x2c/0x40 [spi_hisi_sfc_v3xx]
__handle_irq_event_percpu+0x64/0x1e0
handle_irq_event+0x7c/0x1cc
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Link: https://msgid.link/r/20240123071149.917678-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e421946be7d9bf545147bea8419ef8239cb7ca52 ]
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of pixclock,
it may cause divide-by-zero error.
In sisfb_check_var(), var->pixclock is used as a divisor to caculate
drate before it is checked against zero. Fix this by checking it
at the beginning.
This is similar to CVE-2022-3061 in i740fb which was fixed by
commit 15cf0b8.
Signed-off-by: Fullway Wang <fullwaywang@outlook.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e5eac8f3ab2ff52fa191c187a46d4fdbc1e288 ]
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of pixclock,
it may cause divide-by-zero error.
Although pixclock is checked in savagefb_decode_var(), but it is not
checked properly in savagefb_probe(). Fix this by checking whether
pixclock is zero in the function savagefb_check_var() before
info->var.pixclock is used as the divisor.
This is similar to CVE-2022-3061 in i740fb which was fixed by
commit 15cf0b8.
Signed-off-by: Fullway Wang <fullwaywang@outlook.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcbc84af1183c8cf3d1ca9b78540c2185cd85e7f ]
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240104181059.84032-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6e4f85d3820d00694ed10f581f4c650445dbcda ]
The nl80211_dump_interface() supports resumption
in case nl80211_send_iface() doesn't have the
resources to complete its work.
The logic would store the progress as iteration
offsets for rdev and wdev loops.
However the logic did not properly handle
resumption for non-last rdev. Assuming a system
with 2 rdevs, with 2 wdevs each, this could
happen:
dump(cb=[0, 0]):
if_start=cb[1] (=0)
send rdev0.wdev0 -> ok
send rdev0.wdev1 -> yield
cb[1] = 1
dump(cb=[0, 1]):
if_start=cb[1] (=1)
send rdev0.wdev1 -> ok
// since if_start=1 the rdev0.wdev0 got skipped
// through if_idx < if_start
send rdev1.wdev1 -> ok
The if_start needs to be reset back to 0 upon wdev
loop end.
The problem is actually hard to hit on a desktop,
and even on most routers. The prerequisites for
this manifesting was:
- more than 1 wiphy
- a few handful of interfaces
- dump without rdev or wdev filter
I was seeing this with 4 wiphys 9 interfaces each.
It'd miss 6 interfaces from the last wiphy
reported to userspace.
Signed-off-by: Michal Kazior <michal@plume.com>
Link: https://msgid.link/20240116142340.89678-1-kazikcz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6386f6c995b3ab91c72cfb76e4465553c555a8da ]
We seem to have hit warnings of 'output may be truncated' which is fixed
by increasing the size of 'irq_name'
drivers/dma/fsl-qdma.c: In function ‘fsl_qdma_irq_init’:
drivers/dma/fsl-qdma.c:824:46: error: ‘%d’ directive writing between 1 and 11 bytes into a region of size 10 [-Werror=format-overflow=]
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~
drivers/dma/fsl-qdma.c:824:35: note: directive argument in the range [-2147483641, 2147483646]
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~~~~~~~~~~~~~
drivers/dma/fsl-qdma.c:824:17: note: ‘sprintf’ output between 12 and 22 bytes into a destination of size 20
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 404290240827c3bb5c4e195174a8854eef2f89ac ]
We seem to have hit warnings of 'output may be truncated' which is fixed
by increasing the size of 'dev_id'
drivers/dma/sh/shdmac.c: In function ‘sh_dmae_probe’:
drivers/dma/sh/shdmac.c:541:34: error: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 9 [-Werror=format-truncation=]
541 | "sh-dmae%d.%d", pdev->id, id);
| ^~
In function ‘sh_dmae_chan_probe’,
inlined from ‘sh_dmae_probe’ at drivers/dma/sh/shdmac.c:845:9:
drivers/dma/sh/shdmac.c:541:26: note: directive argument in the range [0, 2147483647]
541 | "sh-dmae%d.%d", pdev->id, id);
| ^~~~~~~~~~~~~~
drivers/dma/sh/shdmac.c:541:26: note: directive argument in the range [0, 19]
drivers/dma/sh/shdmac.c:540:17: note: ‘snprintf’ output between 11 and 21 bytes into a destination of size 16
540 | snprintf(sh_chan->dev_id, sizeof(sh_chan->dev_id),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
541 | "sh-dmae%d.%d", pdev->id, id);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83ab68168a3d990d5ff39ab030ad5754cbbccb25 ]
An abort that is responded to by iSCSI itself is added to tmr_list but does
not go to target core. A LUN_RESET that goes through tmr_list takes a
refcounter on the abort and waits for completion. However, the abort will
be never complete because it was not started in target core.
Unable to locate ITT: 0x05000000 on CID: 0
Unable to locate RefTaskTag: 0x05000000 on CID: 0.
wait_for_tasks: Stopping tmf LUN_RESET with tag 0x0 ref_task_tag 0x0 i_state 34 t_state ISTATE_PROCESSING refcnt 2 transport_state active,stop,fabric_stop
wait for tasks: tmf LUN_RESET with tag 0x0 ref_task_tag 0x0 i_state 34 t_state ISTATE_PROCESSING refcnt 2 transport_state active,stop,fabric_stop
...
INFO: task kworker/0:2:49 blocked for more than 491 seconds.
task:kworker/0:2 state:D stack: 0 pid: 49 ppid: 2 flags:0x00000800
Workqueue: events target_tmr_work [target_core_mod]
Call Trace:
__switch_to+0x2c4/0x470
_schedule+0x314/0x1730
schedule+0x64/0x130
schedule_timeout+0x168/0x430
wait_for_completion+0x140/0x270
target_put_cmd_and_wait+0x64/0xb0 [target_core_mod]
core_tmr_lun_reset+0x30/0xa0 [target_core_mod]
target_tmr_work+0xc8/0x1b0 [target_core_mod]
process_one_work+0x2d4/0x5d0
worker_thread+0x78/0x6c0
To fix this, only add abort to tmr_list if it will be handled by target
core.
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Link: https://lore.kernel.org/r/20240111125941.8688-1-d.bogdanov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 079be8fc630943d9fc70a97807feb73d169ee3fc upstream.
The validation of the value written to sched_rt_period_us was broken
because:
- the sysclt_sched_rt_period is declared as unsigned int
- parsed by proc_do_intvec()
- the range is asserted after the value parsed by proc_do_intvec()
Because of this negative values written to the file were written into a
unsigned integer that were later on interpreted as large positive
integers which did passed the check:
if (sysclt_sched_rt_period <= 0)
return EINVAL;
This commit fixes the parsing by setting explicit range for both
perid_us and runtime_us into the sched_rt_sysctls table and processes
the values with proc_dointvec_minmax() instead.
Alternatively if we wanted to use full range of unsigned int for the
period value we would have to split the proc_handler and use
proc_douintvec() for it however even the
Documentation/scheduller/sched-rt-group.rst describes the range as 1 to
INT_MAX.
As far as I can tell the only problem this causes is that the sysctl
file allows writing negative values which when read back may confuse
userspace.
There is also a LTP test being submitted for these sysctl files at:
http://patchwork.ozlabs.org/project/ltp/patch/20230901144433.2526-1-chrubis@suse.cz/
Signed-off-by: Cyril Hrubis <chrubis@suse.cz>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20231002115553.3007-2-chrubis@suse.cz
[ pvorel: rebased for 5.15, 5.10 ]
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7fcb99877 upstream.
There is a 10% rounding error in the intial value of the
sysctl_sched_rr_timeslice with CONFIG_HZ_300=y.
This was found with LTP test sched_rr_get_interval01:
sched_rr_get_interval01.c:57: TPASS: sched_rr_get_interval() passed
sched_rr_get_interval01.c:64: TPASS: Time quantum 0s 99999990ns
sched_rr_get_interval01.c:72: TFAIL: /proc/sys/kernel/sched_rr_timeslice_ms != 100 got 90
sched_rr_get_interval01.c:57: TPASS: sched_rr_get_interval() passed
sched_rr_get_interval01.c:64: TPASS: Time quantum 0s 99999990ns
sched_rr_get_interval01.c:72: TFAIL: /proc/sys/kernel/sched_rr_timeslice_ms != 100 got 90
What this test does is to compare the return value from the
sched_rr_get_interval() and the sched_rr_timeslice_ms sysctl file and
fails if they do not match.
The problem it found is the intial sysctl file value which was computed as:
static int sysctl_sched_rr_timeslice = (MSEC_PER_SEC / HZ) * RR_TIMESLICE;
which works fine as long as MSEC_PER_SEC is multiple of HZ, however it
introduces 10% rounding error for CONFIG_HZ_300:
(MSEC_PER_SEC / HZ) * (100 * HZ / 1000)
(1000 / 300) * (100 * 300 / 1000)
3 * 30 = 90
This can be easily fixed by reversing the order of the multiplication
and division. After this fix we get:
(MSEC_PER_SEC * (100 * HZ / 1000)) / HZ
(1000 * (100 * 300 / 1000)) / 300
(1000 * 30) / 300 = 100
Fixes: 975e155ed8 ("sched/rt: Show the 'sched_rr_timeslice' SCHED_RR timeslice tuning knob in milliseconds")
Signed-off-by: Cyril Hrubis <chrubis@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Tested-by: Petr Vorel <pvorel@suse.cz>
Link: https://lore.kernel.org/r/20230802151906.25258-2-chrubis@suse.cz
[ pvorel: rebased for 5.15, 5.10 ]
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d877550eaf2dc9090d782864c96939397a3c6835 upstream.
Before this change, the expected size of the user space buffer was
taken from fx_sw->xstate_size. fx_sw->xstate_size can be changed
from user-space, so it is possible construct a sigreturn frame where:
* fx_sw->xstate_size is smaller than the size required by valid bits in
fx_sw->xfeatures.
* user-space unmaps parts of the sigrame fpu buffer so that not all of
the buffer required by xrstor is accessible.
In this case, xrstor tries to restore and accesses the unmapped area
which results in a fault. But fault_in_readable succeeds because buf +
fx_sw->xstate_size is within the still mapped area, so it goes back and
tries xrstor again. It will spin in this loop forever.
Instead, fault in the maximum size which can be touched by XRSTOR (taken
from fpstate->user_size).
[ dhansen: tweak subject / changelog ]
Fixes: fcb3635f50 ("x86/fpu/signal: Handle #PF in the direct restore path")
Reported-by: Konstantin Bogomolov <bogomolov@google.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrei Vagin <avagin@google.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240130063603.3392627-1-avagin%40google.com
Link: https://lore.kernel.org/all/20240130063603.3392627-1-avagin%40google.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14db5f64a971fce3d8ea35de4dfc7f443a3efb92 upstream.
Write error handling is racy and can sometime lead to the error recovery
path wrongly changing the inode size of a sequential zone file to an
incorrect value which results in garbage data being readable at the end
of a file. There are 2 problems:
1) zonefs_file_dio_write() updates a zone file write pointer offset
after issuing a direct IO with iomap_dio_rw(). This update is done
only if the IO succeed for synchronous direct writes. However, for
asynchronous direct writes, the update is done without waiting for
the IO completion so that the next asynchronous IO can be
immediately issued. However, if an asynchronous IO completes with a
failure right before the i_truncate_mutex lock protecting the update,
the update may change the value of the inode write pointer offset
that was corrected by the error path (zonefs_io_error() function).
2) zonefs_io_error() is called when a read or write error occurs. This
function executes a report zone operation using the callback function
zonefs_io_error_cb(), which does all the error recovery handling
based on the current zone condition, write pointer position and
according to the mount options being used. However, depending on the
zoned device being used, a report zone callback may be executed in a
context that is different from the context of __zonefs_io_error(). As
a result, zonefs_io_error_cb() may be executed without the inode
truncate mutex lock held, which can lead to invalid error processing.
Fix both problems as follows:
- Problem 1: Perform the inode write pointer offset update before a
direct write is issued with iomap_dio_rw(). This is safe to do as
partial direct writes are not supported (IOMAP_DIO_PARTIAL is not
set) and any failed IO will trigger the execution of zonefs_io_error()
which will correct the inode write pointer offset to reflect the
current state of the one on the device.
- Problem 2: Change zonefs_io_error_cb() into zonefs_handle_io_error()
and call this function directly from __zonefs_io_error() after
obtaining the zone information using blkdev_report_zones() with a
simple callback function that copies to a local stack variable the
struct blk_zone obtained from the device. This ensures that error
handling is performed holding the inode truncate mutex.
This change also simplifies error handling for conventional zone files
by bypassing the execution of report zones entirely. This is safe to
do because the condition of conventional zones cannot be read-only or
offline and conventional zone files are always fully mapped with a
constant file size.
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 8dcc1a9d90 ("fs: New zonefs file system")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f19a405045 upstream.
Currently we always cleanup/decrement bpf_bprintf_nest_level variable
in bpf_bprintf_cleanup if it's > 0.
There's possible scenario where this could cause a problem, when
bpf_bprintf_prepare does not get bin_args buffer (because num_args is 0)
and following bpf_bprintf_cleanup call decrements bpf_bprintf_nest_level
variable, like:
in task context:
bpf_bprintf_prepare(num_args != 0) increments 'bpf_bprintf_nest_level = 1'
-> first irq :
bpf_bprintf_prepare(num_args == 0)
bpf_bprintf_cleanup decrements 'bpf_bprintf_nest_level = 0'
-> second irq:
bpf_bprintf_prepare(num_args != 0) bpf_bprintf_nest_level = 1
gets same buffer as task context above
Adding check to bpf_bprintf_cleanup and doing the real cleanup only if we
got bin_args data in the first place.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20221215214430.1336195-3-jolsa@kernel.org
[cascardo: there is no bpf_trace_vprintk in 5.15]
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 335ff4990c upstream.
MAX_SNPRINTF_VARARGS and MAX_SEQ_PRINTF_VARARGS are used by bpf helpers
bpf_snprintf and bpf_seq_printf to limit their varargs. Both call into
bpf_bprintf_prepare for print formatting logic and have convenience
macros in libbpf (BPF_SNPRINTF, BPF_SEQ_PRINTF) which use the same
helper macros to convert varargs to a byte array.
Changing shared functionality to support more varargs for either bpf
helper would affect the other as well, so let's combine the _VARARGS
macros to make this more obvious.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210917182911.2426606-2-davemarchevsky@fb.com
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1fc6484e1 upstream.
The sched_rr_timeslice can be reset to default by writing value that is
<= 0. However after reading from this file we always got the last value
written, which is not useful at all.
$ echo -1 > /proc/sys/kernel/sched_rr_timeslice_ms
$ cat /proc/sys/kernel/sched_rr_timeslice_ms
-1
Fix this by setting the variable that holds the sysctl file value to the
jiffies_to_msecs(RR_TIMESLICE) in case that <= 0 value was written.
Signed-off-by: Cyril Hrubis <chrubis@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Tested-by: Petr Vorel <pvorel@suse.cz>
Cc: Mahmoud Adam <mngyadam@amazon.com>
Link: https://lore.kernel.org/r/20230802151906.25258-3-chrubis@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 76025cc2285d9ede3d717fe4305d66f8be2d9346 ]
The data offset for the SMB3.1.1 POSIX create context will always be
8-byte aligned so having the check 'noff + nlen >= doff' in
smb2_parse_contexts() is wrong as it will lead to -EINVAL because noff
+ nlen == doff.
Fix the sanity check to correctly handle aligned create context data.
Fixes: af1689a9b770 ("smb: client: fix potential OOBs in smb2_parse_contexts()")
Signed-off-by: Paulo Alcantara <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
[Guru:smb2_parse_contexts() is present in file smb2ops.c,
smb2ops.c file location is changed, modified patch accordingly.]
Signed-off-by: Guruswamy Basavaiah <guruswamy.basavaiah@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eec04ea119691e65227a97ce53c0da6b9b74b0b7 ]
Fix potential OOB in receive_encrypted_standard() if server returned a
large shdr->NextCommand that would end up writing off the end of
@next_buffer.
Fixes: b24df3e30c ("cifs: update receive_encrypted_standard to handle compounded responses")
Cc: stable@vger.kernel.org
Reported-by: Robert Morris <rtm@csail.mit.edu>
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
[Guru: receive_encrypted_standard() is present in file smb2ops.c,
smb2ops.c file location is changed, modified patch accordingly.]
Signed-off-by: Guruswamy Basavaiah <guruswamy.basavaiah@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbe77c14ee upstream.
The dsmark qdisc has served us well over the years for diffserv but has not
been getting much attention due to other more popular approaches to do diffserv
services. Most recently it has become a shooting target for syzkaller. For this
reason, we are retiring it.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb38306ceb upstream.
The ATM qdisc has served us well over the years but has not been getting much
TLC due to lack of known users. Most recently it has become a shooting target
for syzkaller. For this reason, we are retiring it.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 051d442098 upstream.
While this amazing qdisc has served us well over the years it has not been
getting any tender love and care and has bitrotted over time.
It has become mostly a shooting target for syzkaller lately.
For this reason, we are retiring it. Goodbye CBQ - we loved you.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4e3ef5685 upstream.
If we delay sending End Transfer for Setup TRB to be prepared, we need
to check if the End Transfer was in preparation for a driver
teardown/soft-disconnect. In those cases, just send the End Transfer
command without delay.
In the case of soft-disconnect, there's a very small chance the command
may not go through immediately. But should it happen, the Setup TRB will
be prepared during the polling of the controller halted state, allowing
the command to go through then.
In the case of disabling endpoint due to reconfiguration (e.g.
set_interface(alt-setting) or usb reset), then it's driven by the host.
Typically the host wouldn't immediately cancel the control request and
send another control transfer to trigger the End Transfer command
timeout.
Fixes: 4db0fbb601 ("usb: dwc3: gadget: Don't delay End Transfer on delayed_status")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f1617a323e190b9cc408fb8b65456e32b5814113.1670546756.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4db0fbb601 upstream.
The gadget driver may wait on the request completion when it sets the
USB_GADGET_DELAYED_STATUS. Make sure that the End Transfer command can
go through if the dwc->delayed_status is set so that the request can
complete. When the delayed_status is set, the Setup packet is already
processed, and the next phase should be either Data or Status. It's
unlikely that the host would cancel the control transfer and send a new
Setup packet during End Transfer command. But if that's the case, we can
try again when ep0state returns to EP0_SETUP_PHASE.
Fixes: e1ee843488 ("usb: dwc3: gadget: Force sending delayed status during soft disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3f9f59e5d74efcbaee444cf4b30ef639cc7b124e.1666146954.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb3e28c1e8 upstream.
The kernel is globally removing the ambiguous 0-length and 1-element
arrays in favor of flexible arrays, so that we can gain both compile-time
and run-time array bounds checking[1].
Replace the trailing 1-element array with a flexible array in the
following structures:
struct smb2_err_rsp
struct smb2_tree_connect_req
struct smb2_negotiate_rsp
struct smb2_sess_setup_req
struct smb2_sess_setup_rsp
struct smb2_read_req
struct smb2_read_rsp
struct smb2_write_req
struct smb2_write_rsp
struct smb2_query_directory_req
struct smb2_query_directory_rsp
struct smb2_set_info_req
struct smb2_change_notify_rsp
struct smb2_create_rsp
struct smb2_query_info_req
struct smb2_query_info_rsp
Replace the trailing 1-element array with a flexible array, but leave
the existing structure padding:
struct smb2_file_all_info
struct smb2_lock_req
Adjust all related size calculations to match the changes to sizeof().
No machine code output or .data section differences are produced after
these changes.
[1] For lots of details, see both:
https://docs.kernel.org/process/deprecated.html#zero-length-and-one-element-arrayshttps://people.kernel.org/kees/bounded-flexible-arrays-in-c
Cc: Steve French <sfrench@samba.org>
Cc: Paulo Alcantara <pc@cjr.nz>
Cc: Ronnie Sahlberg <lsahlber@redhat.com>
Cc: Shyam Prasad N <sprasad@microsoft.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Reviewed-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Vasiliy Kovalev <kovalev@altlinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9f31047ba upstream.
We had a number of short comings:
- EEE must be re-evaluated whenever the state machine detects a link
change as wight be switching from a link partner with EEE
enabled/disabled
- tx_lpi_enabled controls whether EEE should be enabled/disabled for the
transmit path, which applies to the TBUF block
- We do not need to forcibly enable EEE upon system resume, as the PHY
state machine will trigger a link event that will do that, too
Fixes: 6ef398ea60 ("net: bcmgenet: add EEE support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230606214348.2408018-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3eefb2fbf4.
libbpf support for "tc" progs doesn't exist for the linux-5.15.y tree.
This commit was backported too far back in upstream, to a kernel where
the libbpf support was not there for the test.
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4060db925 ]
The PM Runtime docs say:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
>From grepping code, it's clear that many people aren't aware of the
need to call pm_runtime_dont_use_autosuspend().
When brainstorming solutions, one idea that came up was to leverage
the new-ish devm_pm_runtime_enable() function. The idea here is that:
* When the devm action is called we know that the driver is being
removed. It's the perfect time to undo the use_autosuspend.
* The code of pm_runtime_dont_use_autosuspend() already handles the
case of being called when autosuspend wasn't enabled.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 3d07a411b4fa ("drm/msm/dsi: Use pm_runtime_resume_and_get to prevent refcnt leaks")
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd504bcfec41a503b32054da5472904b404341a4 upstream.
The kvmalloc function fails with a warning if the size is larger than
INT_MAX. The warning was triggered by a syscall testing robot.
In order to avoid the warning, this commit limits the number of targets to
1048576 and the size of the parameter area to 1073741824.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: He Gao <hegao@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bc09b397cbf1221f8a8aacb1152650c9195b02b upstream.
According to a syzbot report, end_buffer_async_write(), which handles the
completion of block device writes, may detect abnormal condition of the
buffer async_write flag and cause a BUG_ON failure when using nilfs2.
Nilfs2 itself does not use end_buffer_async_write(). But, the async_write
flag is now used as a marker by commit 7f42ec3941 ("nilfs2: fix issue
with race condition of competition between segments for dirty blocks") as
a means of resolving double list insertion of dirty blocks in
nilfs_lookup_dirty_data_buffers() and nilfs_lookup_node_buffers() and the
resulting crash.
This modification is safe as long as it is used for file data and b-tree
node blocks where the page caches are independent. However, it was
irrelevant and redundant to also introduce async_write for segment summary
and super root blocks that share buffers with the backing device. This
led to the possibility that the BUG_ON check in end_buffer_async_write
would fail as described above, if independent writebacks of the backing
device occurred in parallel.
The use of async_write for segment summary buffers has already been
removed in a previous change.
Fix this issue by removing the manipulation of the async_write flag for
the remaining super root block buffer.
Link: https://lkml.kernel.org/r/20240203161645.4992-1-konishi.ryusuke@gmail.com
Fixes: 7f42ec3941 ("nilfs2: fix issue with race condition of competition between segments for dirty blocks")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+5c04210f7c7f897c1e7f@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/00000000000019a97c05fd42f8c8@google.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 944d5fe50f3f03daacfea16300e656a1691c4a23 upstream.
On some systems, sys_membarrier can be very expensive, causing overall
slowdowns for everything. So put a lock on the path in order to
serialize the accesses to prevent the ability for this to be called at
too high of a frequency and saturate the machine.
Reviewed-and-tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Fixes: 22e4ebb975 ("membarrier: Provide expedited private command")
Fixes: c5f58bd58f ("membarrier: Provide GLOBAL_EXPEDITED command")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ converted to explicit mutex_*() calls - cleanup.h is not in this stable
branch - gregkh ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27c5a095e2518975e20a10102908ae8231699879 upstream.
The patch fdb8e12cc2cc ("netfilter: ipset: fix performance regression
in swap operation") missed to add the calls to gc cancellations
at the error path of create operations and at module unload. Also,
because the half of the destroy operations now executed by a
function registered by call_rcu(), neither NFNL_SUBSYS_IPSET mutex
or rcu read lock is held and therefore the checking of them results
false warnings.
Fixes: 97f7cf1cd80e ("netfilter: ipset: fix performance regression in swap operation")
Reported-by: syzbot+52bbc0ad036f6f0d4a25@syzkaller.appspotmail.com
Reported-by: Brad Spengler <spender@grsecurity.net>
Reported-by: Стас Ничипорович <stasn77@gmail.com>
Tested-by: Brad Spengler <spender@grsecurity.net>
Tested-by: Стас Ничипорович <stasn77@gmail.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c52310f26 upstream.
While in theory the timer can be triggered before expires + delta, for the
cases of RT tasks they really have no business giving any lenience for
extra slack time, so override any passed value by the user and always use
zero for schedule_hrtimeout_range() calls. Furthermore, this is similar to
what the nanosleep(2) family already does with current->timer_slack_ns.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230123173206.6764-3-dave@stgolabs.net
Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97f7cf1cd80eeed3b7c808b7c12463295c751001 upstream.
The patch "netfilter: ipset: fix race condition between swap/destroy
and kernel side add/del/test", commit 28628fa9 fixes a race condition.
But the synchronize_rcu() added to the swap function unnecessarily slows
it down: it can safely be moved to destroy and use call_rcu() instead.
Eric Dumazet pointed out that simply calling the destroy functions as
rcu callback does not work: sets with timeout use garbage collectors
which need cancelling at destroy which can wait. Therefore the destroy
functions are split into two: cancelling garbage collectors safely at
executing the command received by netlink and moving the remaining
part only into the rcu callback.
Link: https://lore.kernel.org/lkml/C0829B10-EAA6-4809-874E-E1E9C05A8D84@automattic.com/
Fixes: 28628fa952fe ("netfilter: ipset: fix race condition between swap/destroy and kernel side add/del/test")
Reported-by: Ale Crismani <ale.crismani@automattic.com>
Reported-by: David Wang <00107082@163.com>
Tested-by: David Wang <00107082@163.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit efbd6398353315b7018e6943e41fee9ec35e875f ]
GNU's addr2line can have problems parsing a vmlinux built with LLVM,
particularly when LTO was used. In order to decode the traces correctly
this patch adds the ability to switch to LLVM's utilities readelf and
addr2line. The same approach is followed by Will in [1].
Before:
$ scripts/decode_stacktrace.sh vmlinux < kernel.log
[17716.240635] Call trace:
[17716.240646] skb_cow_data (??:?)
[17716.240654] esp6_input (ld-temp.o:?)
[17716.240666] xfrm_input (ld-temp.o:?)
[17716.240674] xfrm6_rcv (??:?)
[...]
After:
$ LLVM=1 scripts/decode_stacktrace.sh vmlinux < kernel.log
[17716.240635] Call trace:
[17716.240646] skb_cow_data (include/linux/skbuff.h:2172 net/core/skbuff.c:4503)
[17716.240654] esp6_input (net/ipv6/esp6.c:977)
[17716.240666] xfrm_input (net/xfrm/xfrm_input.c:659)
[17716.240674] xfrm6_rcv (net/ipv6/xfrm6_input.c:172)
[...]
Note that one could set CROSS_COMPILE=llvm- instead to hack around this
issue. However, doing so can break the decodecode routine as it will
force the selection of other LLVM utilities down the line e.g. llvm-as.
[1] https://lore.kernel.org/all/20230914131225.13415-3-will@kernel.org/
Link: https://lkml.kernel.org/r/20230929034836.403735-1-cmllamas@google.com
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Tested-by: Justin Stitt <justinstitt@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Stultz <jstultz@google.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Tom Rix <trix@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
