[ Upstream commit 9ad0c1252e ]
Reset signal is asserted by writing 0 to the corresponding locations of
masters we want to reset. So in order to deassert all reset signals, we
should write 1's to all locations.
Current code writes 1's to locations of masters which were just reset
which is good. However, at the same time it also writes 0's to other
locations and thus asserts reset signals of remaining masters. Fix code
by writing all 1's when we want to deassert all reset signals.
This bug was discovered when working with Cedrus (video decoder). When
it faulted, display went blank due to reset signal assertion.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-2-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf8d2dd2ed ]
Since commit fa7e9ecc5e ("iommu/s390: Tolerate repeat attach_dev
calls") we can end up with duplicates in the list of devices attached to
a domain. This is inefficient and confusing since only one domain can
actually be in control of the IOMMU translations for a device. Fix this
by detaching the device from the previous domain, if any, on attach.
Add a WARN_ON() in case we still have attached devices on freeing the
domain. While here remove the re-attach on failure dance as it was
determined to be unlikely to help and may confuse debug and recovery.
Fixes: fa7e9ecc5e ("iommu/s390: Tolerate repeat attach_dev calls")
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20221025115657.1666860-2-schnelle@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38cd167d1f ]
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant delay period
configuration while increasing the unnecessarily low timer slack
somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-15-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 922adfd59e ("phy: qcom-qmp-usb: correct registers layout for IPQ8074 USB3 PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51bd33069f ]
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
But as the vendor kernel do have a 1 ms delay *after* starting the PHY
and before starting to poll the status it is possible that later
contributors have simply not noticed that the mainline power-down delay
is not equivalent.
As the current delay before even starting the PHY is pretty much
pointless and likely a mistake, move the delay after starting the PHY
which avoids a few iterations of polling and speeds up startup by 1 ms
(the poll loop otherwise takes about 1.8 ms).
Note that MSM8998 has never used a power-down delay so add a flag to
skip the delay in case starting the PHY is faster on MSM8998. This can
be removed after someone takes a measurement.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012081241.18273-10-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 4a9eac5ae2 ("phy: qcom-qmp-pcie: fix sc8180x initialisation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e71906144b ]
The power-down delay was included in the first version of the QMP driver
as an optional delay after powering on the PHY (using
POWER_DOWN_CONTROL) and just before starting it. Later changes modified
this sequence by powering on before initialising the PHY, but the
optional delay stayed where it was (i.e. before starting the PHY).
The vendor driver does not use a delay before starting the PHY and this
is likely not needed on any platform unless there is a corresponding
delay in the vendor kernel init sequence tables (i.e. in devicetree).
Let's keep the delay for now, but drop the redundant delay period
configuration while increasing the unnecessarily low timer slack
somewhat.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012081241.18273-9-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 4a9eac5ae2 ("phy: qcom-qmp-pcie: fix sc8180x initialisation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 568aa6dd64 ]
There's a previously unknown part of the controller interface: We have
to assign SRAM carveouts to channels to store their in-flight samples
in. So, obtain the size of the SRAM from a read-only register and divide
it into 2K blocks for allocation to channels. The FIFO depths we
configure will always fit into 2K.
(This fixes audio artifacts during simultaneous playback/capture on
multiple channels -- which looking back is fully accounted for by having
had the caches in the DMA controller overlap in memory.)
Fixes: b127315d9a ("dmaengine: apple-admac: Add Apple ADMAC driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221019132324.8585-2-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91123b37e8 ]
In current code, dev.max_batch_size and wq.max_batch_size attributes in
sysfs are exposed to user to show or update the values.
>From Intel IAA spec [1], Intel IAA does not support batch processing. So
these sysfs attributes should not be supported on IAA device.
Fix this issue by making the attributes of max_batch_size invisible in
sysfs through is_visible() filter when the device is IAA.
Add description in the ABI documentation to mention that the attributes
are not visible when the device does not support batch.
[1]: https://cdrdv2.intel.com/v1/dl/getContent/721858
Fixes: e7184b159d ("dmaengine: idxd: add support for configurable max wq batch size")
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220930201528.18621-3-xiaochen.shen@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d93887cb4 ]
Since commit 0d58280cf1 ("phy: Update PHY power control sequence") the
PHY is powered on before configuring the registers and only the MSM8996
PCIe PHY, which includes the POWER_DOWN_CONTROL register in its PCS
initialisation table, may possibly require a second update afterwards.
To make things worse, the POWER_DOWN_CONTROL register lies at a
different offset on more recent SoCs so that the second update, which
still used a hard-coded offset, would write to an unrelated register
(e.g. a revision-id register on SC8280XP).
As the MSM8996 PCIe PHY is now handled by a separate driver, simply drop
the bogus register update.
Fixes: e4d8b05ad5 ("phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB") added support
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #RB3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221017065013.19647-12-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b01d622d76 ]
Turris MOX board with older ARM Trusted Firmware version v1.5 is not able
to detect any USB 3.0 device connected to USB-A port on Mox-A module after
commit 0a6fc70d76 ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken
reset support"). On the other hand USB 2.0 devices connected to the same
USB-A port are working fine.
It looks as if the older firmware configures COMPHY registers for USB 3.0
somehow incompatibly for kernel driver. Experiments show that resetting
COMPHY registers via setting SFT_RST auto-clearing bit in COMPHY_SFT_RESET
register fixes this issue.
Reset the COMPHY in mvebu_a3700_comphy_usb3_power_on() function as a first
step after selecting COMPHY lane and USB 3.0 function. With this change
Turris MOX board can successfully detect USB 3.0 devices again.
Before the above mentioned commit this reset was implemented in PHY reset
method, so this is the reason why there was no issue with older firmware
version then.
Fixes: 0a6fc70d76 ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken reset support")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20220920121154.30115-1-pali@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5244ca8867 ]
The previous build fix left a remaining issue in configurations with
64-bit dma_addr_t on 32-bit architectures:
drivers/infiniband/sw/siw/siw_qp_tx.c: In function 'siw_get_pblpage':
drivers/infiniband/sw/siw/siw_qp_tx.c:32:37: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
32 | return virt_to_page((void *)paddr);
| ^
Use the same double cast here that the driver uses elsewhere to convert
between dma_addr_t and void*.
Fixes: 0d1b756acf ("RDMA/siw: Pass a pointer to virt_to_page()")
Link: https://lore.kernel.org/r/20221215170347.2612403-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bernard Metzler <bmt@zurich.ibm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c587e77e10 ]
The -D/--delay option is to delay the measure after the program starts.
But the current code goes to sleep before starting the program so the
program is delayed too. This is not the intention, let's fix it.
Before:
$ time sudo ./perf stat -a -e cycles -D 3000 sleep 4
Events disabled
Events enabled
Performance counter stats for 'system wide':
4,326,949,337 cycles
4.007494118 seconds time elapsed
real 0m7.474s
user 0m0.356s
sys 0m0.120s
It ran the workload for 4 seconds and gave the 3 second delay. So it
should skip the first 3 second and measure the last 1 second only. But
as you can see, it delays 3 seconds and ran the workload after that for
4 seconds. So the total time (real) was 7 seconds.
After:
$ time sudo ./perf stat -a -e cycles -D 3000 sleep 4
Events disabled
Events enabled
Performance counter stats for 'system wide':
1,063,551,013 cycles
1.002769510 seconds time elapsed
real 0m4.484s
user 0m0.385s
sys 0m0.086s
The bug was introduced when it changed enablement of system-wide events
with a command line workload. But it should've considered the initial
delay case. The code was reworked since then (in bb8bc52e75) so I'm
afraid it won't be applied cleanly.
Fixes: d0a0a51149 ("perf stat: Fix forked applications enablement of counters")
Reported-by: Kevin Nomura <nomurak@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: https://lore.kernel.org/r/20221212230820.901382-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38792972de ]
The recent switch on arm64 from DYNAMIC_FTRACE_WITH_REGS to
DYNAMIC_FTRACE_WITH_ARGS failed to take into account that we currently
require the former in order to allow the function graph tracer to be
enabled in combination with shadow call stacks. This means that this is
no longer permitted at all, in spite of the fact that either flavour of
ftrace works perfectly fine in this combination.
So permit WITH_ARGS as well as WITH_REGS.
Fixes: ddc9863e9e ("scs: Disable when function graph tracing is enabled")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20221213132407.1485025-1-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 135780f104 ]
The current setting lives in bits 4:2 (as also defined by the mask) but
the current limit defines in the driver use bits 2:0 which should be
shifted over so they don't get masked out completely (except for 17.5mA
which became 10mA).
Now checking /sys/kernel/debug/regmap/1-0068/registers shows that the
current limit is applied correctly and doesn't take the default b000 =
42mA.
Fixes: fa877cf1ab ("leds: is31fl319x: Add support for is31fl319{0,1,3} chips")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88f4a9f813 ]
Commit c412a97cf6 changed delete_work_func() to always perform an
inode lookup when gfs2_try_evict() fails. This doesn't make sense as a
gfs2_try_evict() failure indicates that the inode is likely still in
use. Revert that change.
Fixes: c412a97cf6 ("gfs2: Use TRY lock in gfs2_inode_lookup for UNLINKED inodes")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 104bb8a663 ]
when kmalloc() fail to allocate memory in kasprintf(), propname
will be NULL, strcmp() called by of_get_property() will cause
null pointer dereference.
So return ENOMEM if kasprintf() return NULL pointer.
Fixes: 3afb50d712 ("power: supply: core: Add some helpers to use the battery OCV capacity table")
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7aaa80098 ]
The pump_express_work which gets queued from an external_power_changed
callback might be pending / running on remove() (or on probe failure).
Add a devm action cancelling the work, to ensure that it is cancelled.
Note the devm action is added before devm_power_supply_register(), making
it run after devm unregisters the power_supply, so that the work cannot
be queued anymore (this is also why a devm action is used for this).
Fixes: 48f45b094d ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol")
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5cddca235 ]
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Stable-dep-of: a7aaa80098 ("power: supply: bq25890: Ensure pump_express_work is cancelled on remove")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5c10ecaf ]
Pull the regulator registration code into separate function, so it can
be extended to register more regulators later. Currently this is only
moving ifdeffery into one place and other preparatory changes. The
dev_err_probe() output string is changed to explicitly list vbus
regulator failure, so that once more regulators are registered, it
would be clear which one failed.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Stable-dep-of: a7aaa80098 ("power: supply: bq25890: Ensure pump_express_work is cancelled on remove")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54c03bfd09 ]
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 11cb8da018 ("power: supply: Add charger driver for Rockchip RK817")
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Reviewed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4d33381b1 ]
The ab8500_charger_init() returns the platform_driver_register() directly
without checking its return value, if platform_driver_register() failed,
all ab8500_charger_component_drivers are not unregistered.
Fix by unregister ab8500_charger_component_drivers when
platform_driver_register() failed.
Fixes: 1c1f13a006 ("power: supply: ab8500: Move to componentized binding")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ffa9f713c ]
The ssi_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
ssi_pdriver is not unregistered.
Fix by unregister ssi_pdriver when the last platform_driver_register()
failed.
Fixes: 0fae198988 ("HSI: omap_ssi: built omap_ssi and omap_ssi_port into one module")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97f2b4ddb0 ]
cw_bat_probe() calls create_singlethread_workqueue() and not checked the
ret value, which may return NULL. And a null-ptr-deref may happen:
cw_bat_probe()
create_singlethread_workqueue() # failed, cw_bat->wq is NULL
queue_delayed_work()
queue_delayed_work_on()
__queue_delayed_work() # warning here, but continue
__queue_work() # access wq->flags, null-ptr-deref
Check the ret value and return -ENOMEM if it is NULL.
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 955bee204f ]
If devm_gpiod_get_optional() returns error, the charger should be
freed before z2_batt_probe returns according to the context. We
fix it by just gotoing to 'err' branch.
Fixes: a3b4388ea1 ("power: supply: z2_battery: Convert to GPIO descriptors")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f520ce179 ]
perf doesn't provide proper symbol information for specially crafted
.debug files.
Sometimes .debug file may not have similar program header as runtime
ELF file. For example if we generate .debug file using objcopy
--only-keep-debug resulting file will not contain .text, .data and
other runtime sections. That means corresponding program headers will
have zero FileSiz and modified Offset.
Example: program header of text section of libxxx.so:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x00000000003d3000 0x00000000003d3000 0x00000000003d3000
0x000000000055ae80 0x000000000055ae80 R E 0x1000
Same program header after executing:
objcopy --only-keep-debug libxxx.so libxxx.so.debug
LOAD 0x0000000000001000 0x00000000003d3000 0x00000000003d3000
0x0000000000000000 0x000000000055ae80 R E 0x1000
Offset and FileSiz have been changed.
Following formula will not provide correct value, if program header
taken from .debug file (syms_ss):
sym.st_value -= phdr.p_vaddr - phdr.p_offset;
Correct program header information is located inside runtime ELF
file (runtime_ss).
Fixes: 2d86612aac ("perf symbol: Correct address for bss symbols")
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Makhalov <amakhalov@vmware.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srivatsa S. Bhat <srivatsab@vmware.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Vasavi Sirnapalli <vsirnapalli@vmware.com>
Link: http://lore.kernel.org/lkml/1669198696-50547-1-git-send-email-akaher@vmware.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03e9a5d8eb ]
On Arm64 a case is perf tools fails to find the corresponding trace
point folder for system calls listed in the table 'syscalltbl_arm64',
e.g. the generated system call table contains "lookup_dcookie" but we
cannot find out the matched trace point folder for it.
We need to figure out if there have any issue for the generated system
call table, on the other hand, we need to handle the case when trace
point folder is missed under sysfs, this patch sets the flag
syscall::nonexistent as true and returns the error from
trace__read_syscall_info().
Another problem is for trace__syscall_info(), it returns two different
values if a system call doesn't exist: at the first time calling
trace__syscall_info() it returns NULL when the system call doesn't exist,
later if call trace__syscall_info() again for the same missed system
call, it returns pointer of syscall. trace__syscall_info() checks the
condition 'syscalls.table[id].name == NULL', but the name will be
assigned in the first invoking even the system call is not found.
So checking system call's name in trace__syscall_info() is not the right
thing to do, this patch simply checks flag syscall::nonexistent to make
decision if a system call exists or not, finally trace__syscall_info()
returns the consistent result (NULL) if a system call doesn't existed.
Fixes: b8b1033fca ("perf trace: Mark syscall ids that are not allocated to avoid unnecessary error messages")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: bpf@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221121075237.127706-4-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef9b7bf52c ]
Daniel reported that the commit 1ae3e78c08 ("watchdog: iTCO_wdt: No
need to stop the timer in probe") makes QEMU implementation of the iTCO
watchdog not to trigger reboot anymore when NO_REBOOT flag is initially
cleared using this option (in QEMU command line):
-global ICH9-LPC.noreboot=false
The problem with the commit is that it left the unconditional setting of
NO_REBOOT that is not cleared anymore when the kernel keeps pinging the
watchdog (as opposed to the previous code that called iTCO_wdt_stop()
that cleared it).
Fix this so that we only set NO_REBOOT if the watchdog was not initially
running.
Fixes: 1ae3e78c08 ("watchdog: iTCO_wdt: No need to stop the timer in probe")
Reported-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221028062750.45451-1-mika.westerberg@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b79480ce1 ]
If device_add() succeeds, we should call device_del() when want to
get rid of it, so move it into proper jump symbol.
Otherwise, when __power_supply_register() returns fail and goto
wakeup_init_failed to exit, there is still residue device file in sysfs.
When attempt to probe device again, sysfs would complain as below:
sysfs: cannot create duplicate filename '/devices/platform/i2c/i2c-0/0-001c/power_supply/adp5061'
Call Trace:
dump_stack_lvl+0x68/0x85
sysfs_warn_dup.cold+0x1c/0x29
sysfs_create_dir_ns+0x1b1/0x1d0
kobject_add_internal+0x143/0x390
kobject_add+0x108/0x170
Fixes: 80c6463e2f ("power_supply: Fix Oops from NULL pointer dereference from wakeup_source_activate")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aff514e1d ]
If ssi_add_controller() returns error, it should call hsi_put_controller()
to give up the reference that was set in hsi_alloc_controller(), so that
it can call hsi_controller_release() to free controller and ports that
allocated in hsi_alloc_controller().
Fixes: b209e047bc ("HSI: Introduce OMAP SSI driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5181c35ed ]
In error label 'out1' path in ssi_probe(), the pm_runtime_enable()
has not been called yet, so pm_runtime_disable() is not needed.
Fixes: b209e047bc ("HSI: Introduce OMAP SSI driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65319890c3 ]
Especially when CONFIG_LOCKDEP and other debug configs are enabled,
Perf can print the following warning when running the "kernel lock
contention analysis" test:
Warning:
Processed 1378918 events and lost 4 chunks!
Check IO/CPU overload!
Warning:
Processed 4593325 samples and lost 70.00%!
The test already supplies -q to run in quiet mode, so extend quiet mode
to perf_stdio__warning() and also ui__warning() for consistency.
This fixes the following failure due to the extra lines counted:
perf test "lock cont" -vvv
82: kernel lock contention analysis test :
--- start ---
test child forked, pid 3125
Testing perf lock record and perf lock contention
[Fail] Recorded result count is not 1: 9
test child finished with -1
---- end ----
kernel lock contention analysis test: FAILED!
Fixes: ec685de25b ("perf test: Add kernel lock contention test")
Signed-off-by: James Clark <james.clark@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221018094137.783081-2-james.clark@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a943710407 ]
If an error occurs after a successful uvesafb_init_mtrr() call, it must be
undone by a corresponding arch_phys_wc_del() call, as already done in the
remove function.
This has been added in the remove function in commit 63e28a7a5f
("uvesafb: Clean up MTRR code")
Fixes: 8bdb3a2d7d ("uvesafb: the driver core")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35b4f4d4a7 ]
The uvesafb fbdev driver uses memory management information that is not
available on ARCH=um, so don't allow this driver to be built on UML.
Prevents these build errors:
../drivers/video/fbdev/uvesafb.c: In function ‘uvesafb_vbe_init’:
../drivers/video/fbdev/uvesafb.c:807:21: error: ‘__supported_pte_mask’ undeclared (first use in this function)
807 | if (__supported_pte_mask & _PAGE_NX) {
../drivers/video/fbdev/uvesafb.c:807:44: error: ‘_PAGE_NX’ undeclared (first use in this function)
807 | if (__supported_pte_mask & _PAGE_NX) {
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-um@lists.infradead.org
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
