[ Upstream commit bc19c32904 ]
The reset counter is specific for every QCA700x chip. So move this
into the private driver struct. Otherwise we get unpredictable reset
behavior in setups with multiple QCA700x chips.
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c74386d50f ]
In afs_wait_for_call_to_complete(), rather than immediately aborting an
operation if a signal occurs, the code attempts to wait for it to
complete, using a schedule timeout of 2*RTT (or min 2 jiffies) and a
check that we're still receiving relevant packets from the server before
we consider aborting the call. We may even ping the server to check on
the status of the call.
However, there's a missing timeout reset in the event that we do
actually get a packet to process, such that if we then get a couple of
short stalls, we then time out when progress is actually being made.
Fix this by resetting the timeout any time we get something to process.
If it's the failure of the call then the call state will get changed and
we'll exit the loop shortly thereafter.
A symptom of this is data fetches and stores failing with EINTR when
they really shouldn't.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2afd23f78f ]
Having Rx-only AF_XDP sockets can potentially lead to a crash in the
system by a NULL pointer dereference in xsk_umem_consume_tx(). This
function iterates through a list of all sockets tied to a umem and
checks if there are any packets to send on the Tx ring. Rx-only
sockets do not have a Tx ring, so this will cause a NULL pointer
dereference. This will happen if you have registered one or more
Rx-only sockets to a umem and the driver is checking the Tx ring even
on Rx, or if the XDP_SHARED_UMEM mode is used and there is a mix of
Rx-only and other sockets tied to the same umem.
Fixed by only putting sockets with a Tx component on the list that
xsk_umem_consume_tx() iterates over.
Fixes: ac98d8aab6 ("xsk: wire upp Tx zero-copy functions")
Reported-by: Kal Cutter Conley <kal.conley@dectris.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/bpf/1571645818-16244-1-git-send-email-magnus.karlsson@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0ad032e14 ]
If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.
Fixes: 6071bd1aa1 ("netem: Segment GSO packets on enqueue")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7fa12d158 ]
To corrupt a GSO frame we first perform segmentation. We then
proceed using the first segment instead of the full GSO skb and
requeue the rest of the segments as separate packets.
If there are any issues with processing the first segment we
still want to process the rest, therefore we jump to the
finish_segs label.
Commit 177b800746 ("net: netem: fix backlog accounting for
corrupted GSO frames") started using the pointer to the first
segment in the "rest of segments processing", but as mentioned
above the first segment may had already been freed at this point.
Backlog corrections for parent qdiscs have to be adjusted.
Fixes: 177b800746 ("net: netem: fix backlog accounting for corrupted GSO frames")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c551f919a ]
There is a bug in create_safe_exec_page(), when page table is allocated
it is not checked that table is allocated successfully:
But it is dereferenced in: pgd_none(READ_ONCE(*pgdp)). Check that
allocation was successful.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81dde26de9 ]
Before reading the Extended Size field, we should ensure it fits in
the DMI record. There is already a record length check but it does
not cover that field.
It would take a seriously corrupted DMI table to hit that bug, so no
need to worry, but we should still fix it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 6deae96b42 ("firmware, DMI: Add function to look up a handle and return DIMM size")
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd73dfabdd ]
Illegal memory will be touch if SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(41) exceed the size of structure sdma_script_start_addrs(40),
thus cause memory corrupt such as slob block header so that kernel
trap into while() loop forever in slob_free(). Please refer to below
code piece in imx-sdma.c:
for (i = 0; i < sdma->script_number; i++)
if (addr_arr[i] > 0)
saddr_arr[i] = addr_arr[i]; /* memory corrupt here */
That issue was brought by commit a572460be9 ("dmaengine: imx-sdma: Add
support for version 3 firmware") because SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(38->41 3 scripts added) not align with script number added in
sdma_script_start_addrs(2 scripts).
Fixes: a572460be9 ("dmaengine: imx-sdma: Add support for version 3 firmware")
Cc: stable@vger.kernel
Link: https://www.spinics.net/lists/arm-kernel/msg754895.html
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Jurgen Lambrecht <J.Lambrecht@TELEVIC.com>
Link: https://lore.kernel.org/r/1569347584-3478-1-git-send-email-yibin.gong@nxp.com
[vkoul: update the patch title]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 245cdd9fbd ]
When device stop was moved out of reset, test device wasn't updated to
stop before reset, this resulted in a use after free. Fix by invoking
stop appropriately.
Fixes: b211616d71 ("vhost: move -net specific code out")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78e31c4226 ]
On msm8998, vblank timeouts are observed because the DSI controller is not
reset properly, which ends up stalling the MDP. This is because the reset
logic is not correct per the hardware documentation.
The documentation states that after asserting reset, software should wait
some time (no indication of how long), or poll the status register until it
returns 0 before deasserting reset.
wmb() is insufficient for this purpose since it just ensures ordering, not
timing between writes. Since asserting and deasserting reset occurs on the
same register, ordering is already guaranteed by the architecture, making
the wmb extraneous.
Since we would define a timeout for polling the status register to avoid a
possible infinite loop, lets just use a static delay of 20 ms, since 16.666
ms is the time available to process one frame at 60 fps.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Cc: Hai Li <hali@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
[seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 107529e31a ]
smc_rx_recvmsg() first checks if data is available, and then if
RCV_SHUTDOWN is set. There is a race when smc_cdc_msg_recv_action() runs
in between these 2 checks, receives data and sets RCV_SHUTDOWN.
In that case smc_rx_recvmsg() would return from receive without to
process the available data.
Fix that with a final check for data available if RCV_SHUTDOWN is set.
Move the check for data into a function and call it twice.
And use the existing helper smc_rx_data_available().
Fixes: 952310ccf2 ("smc: receive data from RMBE")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 882dcfe5a1 ]
smc_cdc_rxed_any_close_or_senddone() is used as an end condition for the
receive loop. This conflicts with smc_cdc_msg_recv_action() which could
run in parallel and set the bits checked by
smc_cdc_rxed_any_close_or_senddone() before the receive is processed.
In that case we could return from receive with no data, although data is
available. The same applies to smc_rx_wait().
Fix this by checking for RCV_SHUTDOWN only, which is set in
smc_cdc_msg_recv_action() after the receive was actually processed.
Fixes: 952310ccf2 ("smc: receive data from RMBE")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f142c17d1 ]
tcp_memory_pressure is read without holding any lock,
and its value could be changed on other cpus.
Use READ_ONCE() to annotate these lockless reads.
The write side is already using atomic ops.
Fixes: b8da51ebb1 ("tcp: introduce tcp_under_memory_pressure()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60b173ca3d ]
reqsk_queue_empty() is called from inet_csk_listen_poll() while
other cpus might write ->rskq_accept_head value.
Use {READ|WRITE}_ONCE() to avoid compiler tricks
and potential KCSAN splats.
Fixes: fff1f3001c ("tcp: add a spinlock to protect struct request_sock_queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be40a86c31 ]
Without this patch, a command bit in the supported commands mask is only
ever set to unsupported during set online. If a command is ever marked as
unsupported (e.g. because of error during qeth_l2_vnicc_query_cmds),
subsequent successful initialization (offline/online) would not bring it
back.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 819be8108f ]
This patch is to fix a NULL-ptr deref in selinux_socket_connect_helper:
[...] kasan: GPF could be caused by NULL-ptr deref or user memory access
[...] RIP: 0010:selinux_socket_connect_helper+0x94/0x460
[...] Call Trace:
[...] selinux_sctp_bind_connect+0x16a/0x1d0
[...] security_sctp_bind_connect+0x58/0x90
[...] sctp_process_asconf+0xa52/0xfd0 [sctp]
[...] sctp_sf_do_asconf+0x785/0x980 [sctp]
[...] sctp_do_sm+0x175/0x5a0 [sctp]
[...] sctp_assoc_bh_rcv+0x285/0x5b0 [sctp]
[...] sctp_backlog_rcv+0x482/0x910 [sctp]
[...] __release_sock+0x11e/0x310
[...] release_sock+0x4f/0x180
[...] sctp_accept+0x3f9/0x5a0 [sctp]
[...] inet_accept+0xe7/0x720
It was caused by that the 'newsk' sk_socket was not set before going to
security sctp hook when processing asconf chunk with SCTP_PARAM_ADD_IP
or SCTP_PARAM_SET_PRIMARY:
inet_accept()->
sctp_accept():
lock_sock():
lock listening 'sk'
do_softirq():
sctp_rcv(): <-- [1]
asconf chunk arrives and
enqueued in 'sk' backlog
sctp_sock_migrate():
set asoc's sk to 'newsk'
release_sock():
sctp_backlog_rcv():
lock 'newsk'
sctp_process_asconf() <-- [2]
unlock 'newsk'
sock_graft():
set sk_socket <-- [3]
As it shows, at [1] the asconf chunk would be put into the listening 'sk'
backlog, as accept() was holding its sock lock. Then at [2] asconf would
get processed with 'newsk' as asoc's sk had been set to 'newsk'. However,
'newsk' sk_socket is not set until [3], while selinux_sctp_bind_connect()
would deref it, then kernel crashed.
Here to fix it by adding the chunk to sk_backlog until newsk sk_socket is
set when .accept() is done.
Note that sk->sk_socket can be NULL when the sock is closed, so SOCK_DEAD
flag is also needed to check in sctp_newsk_ready().
Thanks to Ondrej for reviewing the code.
Fixes: d452930fd3 ("selinux: Add SCTP support")
Reported-by: Ying Xu <yinxu@redhat.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 520cf60021 ]
Accordingly to Synopsys documentation [1] and [2], when bit PPSEN0
in register MAC_PPS_CONTROL is set it selects the functionality
command in the same register, otherwise selects the functionality
control.
Command functionality is required to either enable (command 0x2)
and disable (command 0x5) the flexible PPS output, but the bit
PPSEN0 is currently set only for enabling.
Set the bit PPSEN0 to properly disable flexible PPS output.
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Fixes: 9a8a02c9d4 ("net: stmmac: Add Flexible PPS support")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5da202c88f ]
The field "name" in struct ptp_clock_info has a fixed size of 16
chars and is used as zero terminated string by clock_name_show()
in drivers/ptp/ptp_sysfs.c
The current initialization value requires 17 chars to fit also the
null termination, and this causes overflow to the next bytes in
the struct when the string is read as null terminated:
hexdump -C /sys/class/ptp/ptp0/clock_name
00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock|
00000010 a0 ac b9 03 0a |.....|
where the extra 4 bytes (excluding the newline) after the string
represent the integer 0x03b9aca0 = 62500000 assigned to the field
"max_adj" that follows "name" in the same struct.
There is no strict requirement for the "name" content and in the
comment in ptp_clock_kernel.h it's reported it should just be 'A
short "friendly name" to identify the clock'.
Replace it with "stmmac ptp".
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Fixes: 92ba688851 ("stmmac: add the support for PTP hw clock driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4123f637a5 ]
ip6erspan driver calls ether_setup(), after commit 61e84623ac
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the erspan device to not be greater
than 1500, this limit value is not correct for ip6erspan tap
device.
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36453c8528 ]
If llc_conn_state_process() sees that llc_conn_service() put the skb on
a list, it will drop one fewer references to it. This is wrong because
the current behavior is that llc_conn_service() never consumes a
reference to the skb.
The code also makes the number of skb references being dropped
conditional on which of ind_prim and cfm_prim are nonzero, yet neither
of these affects how many references are *acquired*. So there is extra
code that tries to fix this up by sometimes taking another reference.
Remove the unnecessary/broken refcounting logic and instead just add an
skb_get() before the only two places where an extra reference is
actually consumed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc8d5db10c ]
All callers of llc_conn_state_process() except llc_build_and_send_pkt()
(via llc_ui_sendmsg() -> llc_ui_send_data()) assume that it always
consumes a reference to the skb. Fix this caller to do the same.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c1295dccc ]
rxrpc_put_*conn() calls trace_rxrpc_conn() after they have done the
decrement of the refcount - which looks at the debug_id in the connection
record. But unless the refcount was reduced to zero, we no longer have the
right to look in the record and, indeed, it may be deleted by some other
thread.
Fix this by getting the debug_id out before decrementing the refcount and
then passing that into the tracepoint.
Fixes: 363deeab6d ("rxrpc: Add connection tracepoint and client conn state tracepoint")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25683bab09 ]
Some setups may not have all Unicast addresses filters available. Check
the number of available filters before trying to setup it.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a8ecc935e ]
Commit 7fd8930f26
"nvme: add a common helper to read Identify Controller data"
has re-introduced an issue that we have attempted to work around in the
past, in commit a310acd7a7 ("NVMe: use split lo_hi_{read,write}q").
The problem is that some PCIe NVMe controllers do not implement 64-bit
outbound accesses correctly, which is why the commit above switched
to using lo_hi_[read|write]q for all 64-bit BAR accesses occuring in
the code.
In the mean time, the NVMe subsystem has been refactored, and now calls
into the PCIe support layer for NVMe via a .reg_read64() method, which
fails to use lo_hi_readq(), and thus reintroduces the problem that the
workaround above aimed to address.
Given that, at the moment, .reg_read64() is only used to read the
capability register [which is known to tolerate split reads], let's
switch .reg_read64() to lo_hi_readq() as well.
This fixes a boot issue on some ARM boxes with NVMe behind a Synopsys
DesignWare PCIe host controller.
Fixes: 7fd8930f26 ("nvme: add a common helper to read Identify Controller data")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83c8c3cf45 ]
As explained in the "net: sched: taprio: Avoid division by zero on
invalid link speed" commit, it is legal for the ethtool API to return
zero as a link speed. So guard against it to ensure we don't perform a
division by zero in kernel.
Fixes: e0a7683d30 ("net/sched: cbs: fix port_rate miscalculation")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 231042181d ]
The "gmac->phy_mode" variable is an enum and in this context GCC will
treat it as an unsigned int so the error handling will never be
triggered.
Fixes: b1c17215d7 ("stmmac: add ipq806x glue layer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a4b62a0b8 ]
The "priv->phy_mode" is an enum and in this context GCC will treat it
as an unsigned int so it can never be less than zero.
Fixes: 492caffa8a ("net: ethernet: nixge: Add support for National Instruments XGE netdev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7eb651212 ]
The "iface" variable is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: b786241253 ("of_mdio: Abstract a general interface for phy connect")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73e211e11b ]
The "lp->phy_mode" is an enum but in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: ee06b1728b ("net: axienet: add support for standard phy-mode binding")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f10210517a ]
The "dwmac->phy_mode" is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f9e88e6ef ]
The "phy_mode" variable is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: 4c270b55a5 ("net: ethernet: socionext: add AVE ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd55f8ddbc ]
The "priv->phy_interface" variable is an enum and in this context GCC
will treat it as an unsigned int so the error handling is never
triggered.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25a584955f ]
The "priv->phy_interface" variable is an enum and in this context GCC
will treat it as unsigned so the error handling will never be
triggered.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 002dfe8085 ]
The "priv->phy_mode" variable is an enum and in this context GCC will
treat it as unsigned to the error handling will never trigger.
Fixes: 57c5bc9ad7 ("net: hisilicon: add hix5hd2 mac driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2861831476 ]
The "chip" variable is an enum, and it's treated as unsigned int by GCC
in this context so the error handling isn't triggered.
Fixes: e8d452923a ("cxgb4: clean up init_one")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31aefe14bc ]
The irqreturn_t type is an enum or an unsigned int in GCC. That
creates to problems because it can't detect if the
self->aq_hw_ops->hw_irq_read() call fails and at the end the function
always returns IRQ_HANDLED.
drivers/net/ethernet/aquantia/atlantic/aq_vec.c:316 aq_vec_isr_legacy() warn: unsigned 'err' is never less than zero.
drivers/net/ethernet/aquantia/atlantic/aq_vec.c:329 aq_vec_isr_legacy() warn: always true condition '(err >= 0) => (0-u32max >= 0)'
Fixes: 970a2e9864 ("net: ethernet: aquantia: Vector operations")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b15e02f0c ]
To make sure the domain tlb flush completes before the
function returns, explicitly wait for its completion.
Signed-off-by: Filippo Sironi <sironi@amazon.de>
Fixes: 42a49f965a ("amd-iommu: flush domain tlb when attaching a new device")
[joro: Added commit message and fixes tag]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e00371af1d ]
When dma_pool_zalloc() fail in sec_alloc_and_fill_hw_sgl(),
dma_pool_free() is invoked, but the parameters that sgl_current and
sgl_current->next_sgl is not match.
Using sec_free_hw_sgl() instead of the original free routine.
Fixes: 915e4e8413 ("crypto: hisilicon - SEC security accelerator driver")
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0791f0df7 ]
vmlinux BTF has more than 64k types.
Its string section is also at the offset larger than 64k.
Adjust both limits to make in-kernel BTF verifier successfully parse in-kernel BTF.
Fixes: 69b693f0ae ("bpf: btf: Introduce BPF Type Format (BTF)")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9101bfa6a ]
__find_linux_mm_pte() returns a page table entry pointer after walking
the page table without holding locks. To make it safe against a THP
split and/or collapse, we disable interrupts around the lockless page
table walk. However we need to keep interrupts disabled as long as we
use the page table entry pointer that is returned.
Fix addr_to_pfn() to do that.
Fixes: ba41e1e1cc ("powerpc/mce: Hookup derror (load/store) UE errors")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Rearrange code slightly and tweak change log wording]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190918145328.28602-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed309bfb48 ]
Since the helper "owl_factor_helper_round_rate" is shared between factor
and composite clocks, using the factor clk specific helper function
like "hw_to_owl_factor" to access its members will create issues when
called from composite clk specific code. Hence, pass the "factor_hw"
struct pointer directly instead of fetching it using factor clk specific
helpers.
This issue has been observed when a composite clock like "sd0_clk" tried
to call "owl_factor_helper_round_rate" resulting in pointer dereferencing
error.
While we are at it, let's rename the "clk_val_best" function to
"owl_clk_val_best" since this is an owl SoCs specific helper.
Fixes: 4bb78fc974 ("clk: actions: Add factor clock support")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190916154546.24982-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9819403055 ]
If inode is newly created, inode page may not synchronize with inode cache,
so fields like .i_inline or .i_extra_isize could be wrong, in below call
path, we may access such wrong fields, result in failing to migrate valid
target block.
Thread A Thread B
- f2fs_create
- f2fs_add_link
- f2fs_add_dentry
- f2fs_init_inode_metadata
- f2fs_add_inline_entry
- f2fs_new_inode_page
- f2fs_put_page
: inode page wasn't updated with inode cache
- gc_data_segment
- is_alive
- f2fs_get_node_page
- datablock_addr
- offset_in_addr
: access uninitialized fields
Fixes: 7a2af766af ("f2fs: enhance on-disk inode structure scalability")
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
