commit 83810f84ec upstream.
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be857b7f77 ]
Events CPU_CYCLES and INSTRUCTIONS can be submitted with two different
perf_event attribute::type values:
- PERF_TYPE_HARDWARE: when invoked via perf tool predefined events name
cycles or cpu-cycles or instructions.
- pmu->type: when invoked via perf tool event name cpu_cf/CPU_CYLCES/ or
cpu_cf/INSTRUCTIONS/. This invocation also selects the PMU to which
the event belongs.
Handle both type of invocations identical for events CPU_CYLCES and
INSTRUCTIONS. They address the same hardware.
The result is different when event modifier exclude_kernel is also set.
Invocation with event modifier for user space event counting fails.
Output before:
# perf stat -e cpum_cf/cpu_cycles/u -- true
Performance counter stats for 'true':
<not supported> cpum_cf/cpu_cycles/u
0.000761033 seconds time elapsed
0.000076000 seconds user
0.000725000 seconds sys
#
Output after:
# perf stat -e cpum_cf/cpu_cycles/u -- true
Performance counter stats for 'true':
349,613 cpum_cf/cpu_cycles/u
0.000844143 seconds time elapsed
0.000079000 seconds user
0.000800000 seconds sys
#
Fixes: 6a82e23f45 ("s390/cpumf: Adjust registration of s390 PMU device drivers")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
[agordeev@linux.ibm.com corrected commit ID of Fixes commit]
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e648783318 ]
This device shares the PCI ID with the Samsung 970 Evo Plus that
does not need or want the quirks. Move the the quirk entry to the
core table based on the model number instead.
Fixes: bc360b0b16 ("nvme-pci: add quirks for Samsung X5 SSDs")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a6254d55e ]
This particular Kioxia device times out and aborts I/O during any load,
but it's more easily observable with discards (fstrim).
The device gets to a state that is also not possible to use
"nvme set-feature" to disable APST.
Booting with nvme_core.default_ps_max_latency=0 solves the issue.
We had a dozen or so of these devices behaving this same way in
customer environments.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af7fae857e ]
Except for pci, all the nvme transport drivers allocate a command within
the driver's pdu. Align pci with everyone else by allocating the nvme
command within pci's pdu and replace the .queue_rq() stack variable with
this.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c03fd85de2 ]
nvme_clear_request() has a check for flag REQ_DONTPREP and it is called
from nvme_init_request() and nvme_setuo_cmd().
The function nvme_init_request() is called from nvme_alloc_request()
and nvme_alloc_request_qid(). From these two callers new request is
allocated everytime. For newly allocated request RQF_DONTPREP is never
set. Since after getting a tag, block layer sets the req->rq_flags == 0
and never sets the REQ_DONTPREP when returning the request :-
nvme_alloc_request()
blk_mq_alloc_request()
blk_mq_rq_ctx_init()
rq->rq_flags = 0 <----
nvme_alloc_request_qid()
blk_mq_alloc_request_hctx()
blk_mq_rq_ctx_init()
rq->rq_flags = 0 <----
The block layer does set req->rq_flags but REQ_DONTPREP is not one of
them and that is set by the driver.
That means we can unconditinally set the REQ_DONTPREP value to the
rq->rq_flags when nvme_init_request()->nvme_clear_request() is called
from above two callers.
Move the check for REQ_DONTPREP from nvme_clear_nvme_request() into
nvme_setup_cmd().
This is needed since nvme_alloc_request() now gets called from fast
path when NVMeOF target is configured with passthru backend to avoid
unnecessary checks in the fast path.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a36604668 ]
Since nvmet_setup_passthru() function falls in fast path when called
from the NVMeOF passthru backend, make it inline.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39dfe84451 ]
Right now nvme_alloc_request() allocates a request from block layer
based on the value of the qid. When qid set to NVME_QID_ANY it used
blk_mq_alloc_request() else blk_mq_alloc_request_hctx().
The function nvme_alloc_request() is called from different context, The
only place where it uses non NVME_QID_ANY value is for fabrics connect
commands :-
nvme_submit_sync_cmd() NVME_QID_ANY
nvme_features() NVME_QID_ANY
nvme_sec_submit() NVME_QID_ANY
nvmf_reg_read32() NVME_QID_ANY
nvmf_reg_read64() NVME_QID_ANY
nvmf_reg_write32() NVME_QID_ANY
nvmf_connect_admin_queue() NVME_QID_ANY
nvme_submit_user_cmd() NVME_QID_ANY
nvme_alloc_request()
nvme_keep_alive() NVME_QID_ANY
nvme_alloc_request()
nvme_timeout() NVME_QID_ANY
nvme_alloc_request()
nvme_delete_queue() NVME_QID_ANY
nvme_alloc_request()
nvmet_passthru_execute_cmd() NVME_QID_ANY
nvme_alloc_request()
nvmf_connect_io_queue() QID
__nvme_submit_sync_cmd()
nvme_alloc_request()
With passthru nvme_alloc_request() now falls into the I/O fast path such
that blk_mq_alloc_request_hctx() is never gets called and that adds
additional branch check in fast path.
Split the nvme_alloc_request() into nvme_alloc_request() and
nvme_alloc_request_qid().
Replace each call of the nvme_alloc_request() with NVME_QID_ANY param
with a call to newly added nvme_alloc_request() without NVME_QID_ANY.
Replace a call to nvme_alloc_request() with QID param with a call to
newly added nvme_alloc_request() and nvme_alloc_request_qid()
based on the qid value set in the __nvme_submit_sync_cmd().
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d2e7c840b ]
The function nvme_alloc_request() is called from different context
(I/O and Admin queue) where callers do not consider the I/O timeout when
called from I/O queue context.
Update nvme_alloc_request() to set the default I/O and Admin timeout
value based on whether the queuedata is set or not.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8af52fe9fd ]
The following sequence currently causes a driver bug warning
when using virtio_net:
# ip link set eth0 up
# echo mem > /sys/power/state (or e.g. # rtcwake -s 10 -m mem)
<resume>
# ip link set eth0 down
Missing register, driver bug
WARNING: CPU: 0 PID: 375 at net/core/xdp.c:138 xdp_rxq_info_unreg+0x58/0x60
Call trace:
xdp_rxq_info_unreg+0x58/0x60
virtnet_close+0x58/0xac
__dev_close_many+0xac/0x140
__dev_change_flags+0xd8/0x210
dev_change_flags+0x24/0x64
do_setlink+0x230/0xdd0
...
This happens because virtnet_freeze() frees the receive_queue
completely (including struct xdp_rxq_info) but does not call
xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the
receive_queue again but does not call xdp_rxq_info_reg().
Actually, parts of virtnet_freeze_down() and virtnet_restore_up()
are almost identical to virtnet_close() and virtnet_open(): only
the calls to xdp_rxq_info_(un)reg() are missing. This means that
we can fix this easily and avoid such problems in the future by
just calling virtnet_close()/open() from the freeze/restore handlers.
Aside from adding the missing xdp_rxq_info calls the only difference
is that the refill work is only cancelled if netif_running(). However,
this should not make any functional difference since the refill work
should only be active if the network interface is actually up.
Fixes: 754b8a21a9 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220621114845.3650258-1-stephan.gerhold@kernkonzept.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e0effd900 ]
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.
According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.
In addition to that, commit b6e0c419f0 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.
Fixes: b6e0c419f0 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3d184c83f ]
In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.
Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb78d1b5ef ]
The recent patch to make afs_getattr consult the server didn't account
for the pseudo-inodes employed by the dynamic root-type afs superblock
not having a volume or a server to access, and thus an oops occurs if
such a directory is stat'd.
Fix this by checking to see if the vnode->volume pointer actually points
anywhere before following it in afs_getattr().
This can be tested by stat'ing a directory in /afs. It may be
sufficient just to do "ls /afs" and the oops looks something like:
BUG: kernel NULL pointer dereference, address: 0000000000000020
...
RIP: 0010:afs_getattr+0x8b/0x14b
...
Call Trace:
<TASK>
vfs_statx+0x79/0xf5
vfs_fstatat+0x49/0x62
Fixes: 2aeb8c86d4 ("afs: Fix afs_getattr() to refetch file status if callback break occurred")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/165408450783.1031787.7941404776393751186.stgit@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81aba8fde ]
commit 979934da9e ("[PATCH] mips: update IRQ handling for vr41xx") added
a function irq_dispatch, and it'll increase irq_err_count when the get_irq
callback returns a negative value, but increase irq_err_count in get_irq
was not removed.
And also, modpost complains once gpio-vr41xx drivers become modules.
ERROR: modpost: "irq_err_count" [drivers/gpio/gpio-vr41xx.ko] undefined!
So it would be a good idea to remove repetitive increase irq_err_count in
get_irq callback.
Fixes: 27fdd325da ("MIPS: Update VR41xx GPIO driver to use gpiolib")
Fixes: 979934da9e ("[PATCH] mips: update IRQ handling for vr41xx")
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: huhai <huhai@kylinos.cn>
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d79d8af8d ]
Before change:
make -C netfilter
TEST: performance
net,port [SKIP]
perf not supported
port,net [SKIP]
perf not supported
net6,port [SKIP]
perf not supported
port,proto [SKIP]
perf not supported
net6,port,mac [SKIP]
perf not supported
net6,port,mac,proto [SKIP]
perf not supported
net,mac [SKIP]
perf not supported
After change:
net,mac [ OK ]
baseline (drop from netdev hook): 2061098pps
baseline hash (non-ranged entries): 1606741pps
baseline rbtree (match on first field only): 1191607pps
set with 1000 full, ranged entries: 1639119pps
ok 8 selftests: netfilter: nft_concat_range.sh
Fixes: 611973c1e0 ("selftests: netfilter: Introduce tests for sets with range concatenation")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jie2x Zhou <jie2x.zhou@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69135c572d ]
After setting the sock ktls, update ctx->sk_proto to sock->sk_prot by
tls_update(), so now ctx->sk_proto->close is tls_sk_proto_close(). When
close the sock, tls_sk_proto_close() is called for sock->sk_prot->close
is tls_sk_proto_close(). But ctx->sk_proto->close() will be executed later
in tls_sk_proto_close(). Thus tls_sk_proto_close() executed repeatedly
occurred. That will trigger the following bug.
=================================================================
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
RIP: 0010:tls_sk_proto_close+0xd8/0xaf0 net/tls/tls_main.c:306
Call Trace:
<TASK>
tls_sk_proto_close+0x356/0xaf0 net/tls/tls_main.c:329
inet_release+0x12e/0x280 net/ipv4/af_inet.c:428
__sock_release+0xcd/0x280 net/socket.c:650
sock_close+0x18/0x20 net/socket.c:1365
Updating a proto which is same with sock->sk_prot is incorrect. Add proto
and sock->sk_prot equality check at the head of tls_update() to fix it.
Fixes: 95fa145479 ("bpf: sockmap/tls, close can race with map free")
Reported-by: syzbot+29c3c12f3214b85ad081@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c58eb1b54f ]
Some usb type-c dongle use irq_hpd request to perform device connection
and disconnection. This patch add handling of both connection and
disconnection are based on the state of hpd_state and sink_count.
Changes in V2:
-- add dp_display_handle_port_ststus_changed()
-- fix kernel test robot complaint
Changes in V3:
-- add encoder_mode_set into struct dp_display_private
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 26b8d66a39 ("drm/msm/dp: promote irq_hpd handle to handle link training correctly")
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26b8d66a39 ]
Some dongles require link training done at irq_hpd request instead
of plugin request. This patch promote irq_hpd handler to handle link
training and setup hpd_state correctly.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 231a04fcc6 ]
DP compo phy have to be enable to start link training. When
link training failed phy need to be disabled so that next
link traning can be proceed smoothly at next plug in. This
patch de-initialize mainlink to disable phy if link training
failed. This prevent system crash due to
disp_cc_mdss_dp_link_intf_clk stuck at "off" state. This patch
also perform checking power_on flag at dp_display_enable() and
dp_display_disable() to avoid crashing when unplug cable while
display is off.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62671d2ef2 ]
Connection state is not set correctly happen when either failure of link
train due to cable unplugged in the middle of aux channel reading or
cable plugged in while in suspended state. This patch fixes these problems.
This patch also replace ST_SUSPEND_PENDING with ST_DISPLAY_OFF.
Changes in V2:
-- Add more information to commit message.
Changes in V3:
-- change base
Changes in V4:
-- add Fixes tag
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2b1a5d40b ]
As reported by Yuming, currently tc always show a latency of UINT_MAX
for netem Qdisc's on 32-bit platforms:
$ tc qdisc add dev dummy0 root netem latency 100ms
$ tc qdisc show dev dummy0
qdisc netem 8001: root refcnt 2 limit 1000 delay 275s 275s
^^^^^^^^^^^^^^^^
Let us take a closer look at netem_dump():
qopt.latency = min_t(psched_tdiff_t, PSCHED_NS2TICKS(q->latency,
UINT_MAX);
qopt.latency is __u32, psched_tdiff_t is signed long,
(psched_tdiff_t)(UINT_MAX) is negative for 32-bit platforms, so
qopt.latency is always UINT_MAX.
Fix it by using psched_time_t (u64) instead.
Note: confusingly, users have two ways to specify 'latency':
1. normally, via '__u32 latency' in struct tc_netem_qopt;
2. via the TCA_NETEM_LATENCY64 attribute, which is s64.
For the second case, theoretically 'latency' could be negative. This
patch ignores that corner case, since it is broken (i.e. assigning a
negative s64 to __u32) anyways, and should be handled separately.
Thanks Ted Lin for the analysis [1] .
[1] https://github.com/raspberrypi/linux/issues/3512
Reported-by: Yuming Chen <chenyuming.junnan@bytedance.com>
Fixes: 112f9cb656 ("netem: convert to qdisc_watchdog_schedule_ns")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20220616234336.2443-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 911600bf5a ]
syzbot found the following issue on:
==================================================================
BUG: KASAN: use-after-free in tipc_named_reinit+0x94f/0x9b0
net/tipc/name_distr.c:413
Read of size 8 at addr ffff88805299a000 by task kworker/1:9/23764
CPU: 1 PID: 23764 Comm: kworker/1:9 Not tainted
5.18.0-rc4-syzkaller-00878-g17d49e6e8012 #0
Hardware name: Google Compute Engine/Google Compute Engine,
BIOS Google 01/01/2011
Workqueue: events tipc_net_finalize_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0xeb/0x495
mm/kasan/report.c:313
print_report mm/kasan/report.c:429 [inline]
kasan_report.cold+0xf4/0x1c6 mm/kasan/report.c:491
tipc_named_reinit+0x94f/0x9b0 net/tipc/name_distr.c:413
tipc_net_finalize+0x234/0x3d0 net/tipc/net.c:138
process_one_work+0x996/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298
</TASK>
[...]
==================================================================
In the commit
d966ddcc38 ("tipc: fix a deadlock when flushing scheduled work"),
the cancel_work_sync() function just to make sure ONLY the work
tipc_net_finalize_work() is executing/pending on any CPU completed before
tipc namespace is destroyed through tipc_exit_net(). But this function
is not guaranteed the work is the last queued. So, the destroyed instance
may be accessed in the work which will try to enqueue later.
In order to completely fix, we re-order the calling of cancel_work_sync()
to make sure the work tipc_net_finalize_work() was last queued and it
must be completed by calling cancel_work_sync().
Reported-by: syzbot+47af19f3307fc9c5c82e@syzkaller.appspotmail.com
Fixes: d966ddcc38 ("tipc: fix a deadlock when flushing scheduled work")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be07f05639 ]
This patch is to use "struct work_struct" for the finalize work queue
instead of "struct tipc_net_work", as it can get the "net" and "addr"
from tipc_net's other members and there is no need to add extra net
and addr in tipc_net by defining "struct tipc_net_work".
Note that it's safe to get net from tn->bcl as bcl is always released
after the finalize work queue is done.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b7fd1670a ]
Even when the eth port is resticted to work with speeds not higher than 1G,
and so the eth driver is requesting the phy (via phylink) to advertise up
to 1000BASET support, the aquantia phy device is still advertising for 2.5G
and 5G speeds.
Clear these advertising defaults when requested.
Cc: Ondrej Spacek <ondrej.spacek@nxp.com>
Fixes: 09c4c57f7b ("net: phy: aquantia: add support for auto-negotiation configuration")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220610084037.7625-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff672c67ee ]
On x86-64 the tail call count is passed from one BPF function to another
through %rax. Additionally, on function entry, the tail call count value
is stored on stack right after the BPF program stack, due to register
shortage.
The stored count is later loaded from stack either when performing a tail
call - to check if we have not reached the tail call limit - or before
calling another BPF function call in order to pass it via %rax.
In the latter case, we miscalculate the offset at which the tail call count
was stored on function entry. The JIT does not take into account that the
allocated BPF program stack is always a multiple of 8 on x86, while the
actual stack depth does not have to be.
This leads to a load from an offset that belongs to the BPF stack, as shown
in the example below:
SEC("tc")
int entry(struct __sk_buff *skb)
{
/* Have data on stack which size is not a multiple of 8 */
volatile char arr[1] = {};
return subprog_tail(skb);
}
int entry(struct __sk_buff * skb):
0: (b4) w2 = 0
1: (73) *(u8 *)(r10 -1) = r2
2: (85) call pc+1#bpf_prog_ce2f79bb5f3e06dd_F
3: (95) exit
int entry(struct __sk_buff * skb):
0xffffffffa0201788: nop DWORD PTR [rax+rax*1+0x0]
0xffffffffa020178d: xor eax,eax
0xffffffffa020178f: push rbp
0xffffffffa0201790: mov rbp,rsp
0xffffffffa0201793: sub rsp,0x8
0xffffffffa020179a: push rax
0xffffffffa020179b: xor esi,esi
0xffffffffa020179d: mov BYTE PTR [rbp-0x1],sil
0xffffffffa02017a1: mov rax,QWORD PTR [rbp-0x9] !!! tail call count
0xffffffffa02017a8: call 0xffffffffa02017d8 !!! is at rbp-0x10
0xffffffffa02017ad: leave
0xffffffffa02017ae: ret
Fix it by rounding up the BPF stack depth to a multiple of 8, when
calculating the tail call count offset on stack.
Fixes: ebf7d1f508 ("bpf, x64: rework pro/epilogue and tailcall handling in JIT")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220616162037.535469-2-jakub@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1342b5b23d ]
If the component driver fails to bind, or is unbound, the driver data
for the top-level platform device points to a freed drm_device. If the
system is then suspended, the driver passes this dangling pointer to
drm_mode_config_helper_suspend(), which crashes.
Fix this by only setting the driver data while the platform driver holds
a reference to the drm_device.
Fixes: 624b4b48d9 ("drm: sun4i: Add support for suspending the display driver")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220615054254.16352-1-samuel@sholland.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3046a82731 ]
A customer reported a request_socket leak in a Calico cloud environment. We
found that a BPF program was doing a socket lookup with takes a refcnt on
the socket and that it was finding the request_socket but returning the parent
LISTEN socket via sk_to_full_sk() without decrementing the child request socket
1st, resulting in request_sock slab object leak. This patch retains the
existing behaviour of returning full socks to the caller but it also decrements
the child request_socket if one is present before doing so to prevent the leak.
Thanks to Curtis Taylor for all the help in diagnosing and testing this. And
thanks to Antoine Tenart for the reproducer and patch input.
v2 of this patch contains, refactor as per Daniel Borkmann's suggestions to
validate RCU flags on the listen socket so that it balances with bpf_sk_release()
and update comments as per Martin KaFai Lau's suggestion. One small change to
Daniels suggestion, put "sk = sk2" under "if (sk2 != sk)" to avoid an extra
instruction.
Fixes: f7355a6c04 ("bpf: Check sk_fullsock() before returning from bpf_sk_lookup()")
Fixes: edbf8c01de ("bpf: add skc_lookup_tcp helper")
Co-developed-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Curtis Taylor <cutaylor-pub@yahoo.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/56d6f898-bde0-bb25-3427-12a330b29fb8@iogearbox.net
Link: https://lore.kernel.org/bpf/20220615011540.813025-1-jmaxwell37@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 566d3c57eb ]
When a write command to a sequential write required or sequential write
preferred zone result in the zone write pointer reaching the end of the
zone, the zone condition must be set to full AND the number of implicitly
or explicitly open zones updated to have a correct accounting for zone
resources. However, the function zbc_inc_wp() only sets the zone condition
to full without updating the open zone counters, resulting in a zone state
machine breakage.
Introduce the helper function zbc_set_zone_full() and use it in
zbc_inc_wp() to correctly transition zones to the full condition.
Link: https://lore.kernel.org/r/20220608011302.92061-1-damien.lemoal@opensource.wdc.com
Fixes: f0d1cf9378 ("scsi: scsi_debug: Add ZBC zone commands")
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1fd94e704 ]
bh might occur while updating per-cpu rnd_state from user context,
ie. local_out path.
BUG: using smp_processor_id() in preemptible [00000000] code: nginx/2725
caller is nft_ng_random_eval+0x24/0x54 [nft_numgen]
Call Trace:
check_preemption_disabled+0xde/0xe0
nft_ng_random_eval+0x24/0x54 [nft_numgen]
Use the random driver instead, this also avoids need for local prandom
state. Moreover, prandom now uses the random driver since d4150779e6
("random32: use real rng for non-deterministic randomness").
Based on earlier patch from Pablo Neira.
Fixes: 6b2faee0ca ("netfilter: nft_meta: place prandom handling in a helper")
Fixes: 978d8f9055 ("netfilter: nft_numgen: add map lookups for numgen random operations")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 345023b0db ]
This new function combines the netlink register attribute parser
and the store validation function.
This update requires to replace:
enum nft_registers dreg:8;
in many of the expression private areas otherwise compiler complains
with:
error: cannot take address of bit-field ‘dreg’
when passing the register field as reference.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f16d25c68 ]
This new function combines the netlink register attribute parser
and the load validation function.
This update requires to replace:
enum nft_registers sreg:8;
in many of the expression private areas otherwise compiler complains
with:
error: cannot take address of bit-field ‘sreg’
when passing the register field as reference.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce0db505bc ]
Following commit 17e822f759 ("drm/msm: fix unbalanced
pm_runtime_enable in adreno_gpu_{init, cleanup}"), any call to
adreno_unbind() will disable runtime PM twice, as indicated by the call
trees below:
adreno_unbind()
-> pm_runtime_force_suspend()
-> pm_runtime_disable()
adreno_unbind()
-> gpu->funcs->destroy() [= aNxx_destroy()]
-> adreno_gpu_cleanup()
-> pm_runtime_disable()
Note that pm_runtime_force_suspend() is called right before
gpu->funcs->destroy() and both functions are called unconditionally.
With recent addition of the eDP AUX bus code, this problem manifests
itself when the eDP panel cannot be found yet and probing is deferred.
On the first probe attempt, we disable runtime PM twice as described
above. This then causes any later probe attempt to fail with
[drm:adreno_load_gpu [msm]] *ERROR* Couldn't power up the GPU: -13
preventing the driver from loading.
As there seem to be scenarios where the aNxx_destroy() functions are not
called from adreno_unbind(), simply removing pm_runtime_disable() from
inside adreno_unbind() does not seem to be the proper fix. This is what
commit 17e822f759 ("drm/msm: fix unbalanced pm_runtime_enable in
adreno_gpu_{init, cleanup}") intended to fix. Therefore, instead check
whether runtime PM is still enabled, and only disable it in that case.
Fixes: 17e822f759 ("drm/msm: fix unbalanced pm_runtime_enable in adreno_gpu_{init, cleanup}")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Link: https://lore.kernel.org/r/20220606211305.189585-1-luzmaximilian@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 90736eb323 upstream.
Commit 85e123c27d ("dm mirror log: round up region bitmap size to
BITS_PER_LONG") introduced a regression on 64-bit architectures in the
lvm testsuite tests: lvcreate-mirror, mirror-names and vgsplit-operation.
If the device is shrunk, we need to clear log bits beyond the end of the
device. The code clears bits up to a 32-bit boundary and then calculates
lc->sync_count by summing set bits up to a 64-bit boundary (the commit
changed that; previously, this boundary was 32-bit too). So, it was using
some non-zeroed bits in the calculation and this caused misbehavior.
Fix this regression by clearing bits up to BITS_PER_LONG boundary.
Fixes: 85e123c27d ("dm mirror log: round up region bitmap size to BITS_PER_LONG")
Cc: stable@vger.kernel.org
Reported-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
