[ Upstream commit c207979f5a ]
comp_ctx can be NULL in a very rare case when an admin command is executed
during the execution of ena_remove().
The bug scenario is as follows:
* ena_destroy_device() sets the comp_ctx to be NULL
* An admin command is executed before executing unregister_netdev(),
this can still happen because our device can still receive callbacks
from the netdev infrastructure such as ethtool commands.
* When attempting to access the comp_ctx, the bug occurs since it's set
to NULL
Fix:
Added a check that comp_ctx is not NULL
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 886d208927 ]
Up till kernel 4.11 there was no enum defined for crc32 hash in ethtool,
thus the xor enum was used for supporting crc32.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3f89f91e9 ]
The function ena_com_ind_tbl_convert_from_device() has an overflow
bug as explained below. Either way, this function is not needed at
all since we don't retrieve the indirection table from the device
at any point which means that this conversion is not needed.
The bug:
The for loop iterates over all io_sq_queues, when passing the actual
number of used queues the io_sq_queues[i].idx equals 0 since they are
uninitialized which results in the following code to be executed till
the end of the loop:
dev_idx_to_host_tbl[0] = i;
This results dev_idx_to_host_tbl[0] in being equal to
ENA_TOTAL_NUM_QUEUES - 1.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92569fd27f ]
The indirection table has the indices of the Rx queues. When we store it
during set indirection operation, we convert the indices to our internal
representation of the indices.
Our internal representation of the indices is: even indices for Tx and
uneven indices for Rx, where every Tx/Rx pair are in a consecutive order
starting from 0. For example if the driver has 3 queues (3 for Tx and 3
for Rx) then the indices are as follows:
0 1 2 3 4 5
Tx Rx Tx Rx Tx Rx
The BUG:
The issue is that when we satisfy a get request for the indirection
table, we don't convert the indices back to the original representation.
The FIX:
Simply apply the inverse function for the indices of the indirection
table after we set it.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4844470d47 ]
The device receives, stores and retrieves the hash function value as bits
and not as their enum value.
The bug:
* In ena_com_set_hash_function() we set
cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func.
(1 << rss->hash_func)
* In ena_com_get_hash_function() we retrieve the hash function and store
it's bit value in rss->hash_func. (Now the bit value of rss->hash_func
is stored in rss->hash_func instead of it's enum value)
The fix:
This commit fixes the issue by converting the retrieved hash function
values from the device to the matching enum value of the set bit using
ffs(). ffs() finds the first set bit's index in a word. Since the function
returns 1 for the LSB's index, we need to subtract 1 from the returned
value (note that BIT(0) is 1).
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c8923c0a6 ]
On old hardware, getting / setting the hash function is not supported while
gettting / setting the indirection table is.
This commit enables us to still show the indirection table on older
hardwares by setting the hash function and key to NULL.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a4f7dc82d ]
Currently we allocate the key whether the device supports setting the
key or not. This commit adds a check to the allocation function and
handles the error accordingly.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d1c3de7b8 ]
Bug description:
When running "ethtool -x <if_name>" the key shows up as all zeros.
When we use "ethtool -X <if_name> hfunc toeplitz hkey <some:random:key>" to
set the key and then try to retrieve it using "ethtool -x <if_name>" then
we return the correct key because we return the one we saved.
Bug cause:
We don't fetch the key from the device but instead return the key
that we have saved internally which is by default set to zero upon
allocation.
Fix:
This commit fixes the issue by initializing the key to a random value
using netdev_rss_key_fill().
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf6d17fde9 ]
Current implementation of the driver calls skb_tx_timestamp()to add a
software tx timestamp to the skb, however the software-transmit capability
is not reported in ethtool -T.
This commit updates the ethtool structure to report the software-transmit
capability in ethtool -T using the standard ethtool_op_get_ts_info().
This function reports all software timestamping capabilities (tx and rx),
as well as setting phc_index = -1. phc_index is the index of the PTP
hardware clock device that will be used for hardware timestamps. Since we
don't have such a device in ENA, using the default -1 value is the correct
setting.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a6e5fa2f4 ]
>From the documentation of round_jiffies():
"Rounds a time delta in the future (in jiffies) up or down to
(approximately) full seconds. This is useful for timers for which
the exact time they fire does not matter too much, as long as
they fire approximately every X seconds.
By rounding these timers to whole seconds, all such timers will fire
at the same time, rather than at various times spread out. The goal
of this is to have the CPU wake up less, which saves power."
There are 2 parts to this patch:
================================
Part 1:
-------
In our case we need timer_service to be called approximately every
X=1 seconds, and the exact time does not matter, so using round_jiffies()
is the right way to go.
Therefore we add round_jiffies() to the mod_timer() in ena_timer_service().
Part 2:
-------
round_jiffies() is used in check_for_missing_keep_alive() when
getting the jiffies of the expiration of the keep_alive timeout. Here it
is actually a mistake to use round_jiffies() because we want the exact
time when keep_alive should expire and not an approximate rounded time,
which can cause early, false positive, timeouts.
Therefore we remove round_jiffies() in the calculation of
keep_alive_expired() in check_for_missing_keep_alive().
Fixes: 82ef30f13b ("net: ena: add hardware hints capability to the driver")
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91a65b7d3e ]
When ethtool -X is called without an hkey, ena_com_fill_hash_function()
is called with key=NULL, which is passed to memcpy causing a crash.
This commit fixes this issue by checking key is not NULL.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f27f37a04a ]
Commit d9d6a9aed3 ("i40e: Fix virtchnl_queue_select bitmap
validation") introduced a necessary change for verifying how queue
bitmaps from the iavf driver get validated. Unfortunately, the
conditional was reversed. Fix this.
Fixes: d9d6a9aed3 ("i40e: Fix virtchnl_queue_select bitmap validation")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 416611d9b6 ]
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c134c3caba ]
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df36f6cf23 ]
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e4473bb50 ]
In O_APPEND & O_DIRECT mode, the data from different writers will
be possibly overlapping each other since they take the shared lock.
For example, both Writer1 and Writer2 are in O_APPEND and O_DIRECT
mode:
Writer1 Writer2
shared_lock() shared_lock()
getattr(CAP_SIZE) getattr(CAP_SIZE)
iocb->ki_pos = EOF iocb->ki_pos = EOF
write(data1)
write(data2)
shared_unlock() shared_unlock()
The data2 will overlap the data1 from the same file offset, the
old EOF.
Switch to exclusive lock instead when O_APPEND is specified.
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ca2c0319a ]
Even though a SMMUv3 PMCG implementation may use an MSI as the form of
interrupt source, the kernel would still complain that it does not find
the wired (GSIV) interrupt in this case:
root@(none)$ dmesg | grep arm-smmu-v3-pmcg | grep "not found"
[ 59.237219] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.8.auto: IRQ index 0 not found
[ 59.322841] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.9.auto: IRQ index 0 not found
[ 59.422155] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.10.auto: IRQ index 0 not found
[ 59.539014] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.11.auto: IRQ index 0 not found
[ 59.640329] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.12.auto: IRQ index 0 not found
[ 59.743112] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.13.auto: IRQ index 0 not found
[ 59.880577] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.14.auto: IRQ index 0 not found
[ 60.017528] arm-smmu-v3-pmcg arm-smmu-v3-pmcg.15.auto: IRQ index 0 not found
Use platform_get_irq_optional() to silence the warning.
If neither interrupt source is found, then the driver will still warn that
IRQ setup errored and the probe will fail.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf5b4059ba ]
We want to make sure that we revalidate the dentry if and only if
we've done an OPEN by filename.
In order to avoid races with remote changes to the directory on the
server, we want to save the verifier before calling OPEN. The exception
is if the server returned a delegation with our OPEN, as we then
know that the filename can't have changed on the server.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: Benjamin Coddington <bcodding@gmail.com>
Tested-by: Benjamin Coddington <bcodding@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00516d13d4 ]
We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.
The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work. This is done based on the knowledge that it
has exactly 2 bulk endpoints. QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.
The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs. Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88bf54603f ]
Commit f25e1392fd removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples. It is therefore
necessary to support both variants.
Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either. Interface 1 will be rejected based on the HID class for the
production variant:
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
And interface 0 will be rejected based on too few endpoints for the
pre-production variant:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Fixes: f25e1392fd ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNk
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcd98d4002 ]
The internal statistic counters for the total number of
requests processed per card and per queue used integers. So they do
wrap after a rather huge amount of crypto requests processed. This
patch introduces uint64 counters which should hold much longer but
still may wrap. The sysfs attributes request_count for card and queue
also used only %ld and now display the counter value with %llu.
This is not a security relevant fix. The int overflow which happened
is not in any way exploitable as a security breach.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a04564c99b ]
We only use the parsing CRC for checking if a beacon changed,
and elements with an ID > 63 cannot be represented in the
filter. Thus, like we did before with WMM and Cisco vendor
elements, just statically add these forgotten items to the
CRC:
- WLAN_EID_VHT_OPERATION
- WLAN_EID_OPMODE_NOTIF
I guess that in most cases when VHT/HE operation change, the HT
operation also changed, and so the change was picked up, but we
did notice that pure operating mode notification changes were
ignored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-22-luca@coelho.fi
[restrict to VHT for the mac80211 branch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a4b03ffc6 ]
When a running task is moved on a throttled task group and there is no
other task enqueued on the CPU, the task can keep running using 100% CPU
whatever the allocated bandwidth for the group and although its cfs rq is
throttled. Furthermore, the group entity of the cfs_rq and its parents are
not enqueued but only set as curr on their respective cfs_rqs.
We have the following sequence:
sched_move_task
-dequeue_task: dequeue task and group_entities.
-put_prev_task: put task and group entities.
-sched_change_group: move task to new group.
-enqueue_task: enqueue only task but not group entities because cfs_rq is
throttled.
-set_next_task : set task and group_entities as current sched_entity of
their cfs_rq.
Another impact is that the root cfs_rq runnable_load_avg at root rq stays
null because the group_entities are not enqueued. This situation will stay
the same until an "external" event triggers a reschedule. Let trigger it
immediately instead.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Ben Segall <bsegall@google.com>
Link: https://lkml.kernel.org/r/1579011236-31256-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebc0f83c78 ]
The way loadavg is tracked during nohz only pays attention to the load
upon entering nohz. This can be particularly noticeable if full nohz is
entered while non-idle, and then the cpu goes idle and stays that way for
a long time.
Use the remote tick to ensure that full nohz cpus report their deltas
within a reasonable time.
[ swood: Added changelog and removed recheck of stopped tick. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/1578736419-14628-3-git-send-email-swood@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b8526d3ab ]
In error cases a NULL can be passed to memcpy. The length will always
be zero, so it doesn't really matter, but go ahead and check for NULL,
anyway, to be more precise and avoid static analysis errors.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afecdb376b ]
When splitting an RTA_MULTIPATH request into multiple routes and adding the
second and later components, we must not simply remove NLM_F_REPLACE but
instead replace it by NLM_F_CREATE. Otherwise, it may look like the netlink
message was malformed.
For example,
ip route add 2001:db8::1/128 dev dummy0
ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 \
nexthop via fe80::30:2 dev dummy0
results in the following warnings:
[ 1035.057019] IPv6: RTM_NEWROUTE with no NLM_F_CREATE or NLM_F_REPLACE
[ 1035.057517] IPv6: NLM_F_CREATE should be set when creating new route
This patch makes the nlmsg sequence look equivalent for __ip6_ins_rt() to
what it would get if the multipath route had been added in multiple netlink
operations:
ip route add 2001:db8::1/128 dev dummy0
ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0
ip route append 2001:db8::1/128 nexthop via fe80::30:2 dev dummy0
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e404b8c7cf ]
After commit 2759647247 ("ipv6: fix ECMP route replacement") it is no
longer possible to replace an ECMP-able route by a non ECMP-able route.
For example,
ip route add 2001:db8::1/128 via fe80::1 dev dummy0
ip route replace 2001:db8::1/128 dev dummy0
does not work as expected.
Tweak the replacement logic so that point 3 in the log of the above commit
becomes:
3. If the new route is not ECMP-able, and no matching non-ECMP-able route
exists, replace matching ECMP-able route (if any) or add the new route.
We can now summarize the entire replace semantics to:
When doing a replace, prefer replacing a matching route of the same
"ECMP-able-ness" as the replace argument. If there is no such candidate,
fallback to the first route found.
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7151affeef ]
netdev_next_lower_dev_rcu() will be used to implement a function,
which is to walk all lower interfaces.
There are already functions that they walk their lower interface.
(netdev_walk_all_lower_dev_rcu, netdev_walk_all_lower_dev()).
But, there would be cases that couldn't be covered by given
netdev_walk_all_lower_dev_{rcu}() function.
So, some modules would want to implement own function,
which is to walk all lower interfaces.
In the next patch, netdev_next_lower_dev_rcu() will be used.
In addition, this patch removes two unused prototypes in netdevice.h.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8743db4a9a ]
If crashed kernel does not shutdown the NIC properly, PCIe FLR
is required in the kdump kernel in order to initialize all the
functions properly.
Fixes: d629522e1d ("bnxt_en: Reduce memory usage when running in kdump kernel.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5567ae4a8d ]
Especially when bnxt_shutdown() is called during kexec, we need to
disable MSIX and disable Bus Master to completely quiesce the device.
Make these 2 calls unconditionally in the shutdown method.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 245709ec8b ]
When T2 timer is to be stopped, the asoc should also be deleted,
otherwise, there will be no chance to call sctp_association_free
and the asoc could last in memory forever.
However, in sctp_sf_shutdown_sent_abort(), after adding the cmd
SCTP_CMD_TIMER_STOP for T2 timer, it may return error due to the
format error from __sctp_sf_do_9_1_abort() and miss adding
SCTP_CMD_ASSOC_FAILED where the asoc will be deleted.
This patch is to fix it by moving the format error check out of
__sctp_sf_do_9_1_abort(), and do it before adding the cmd
SCTP_CMD_TIMER_STOP for T2 timer.
Thanks Hangbin for reporting this issue by the fuzz testing.
v1->v2:
- improve the comment in the code as Marcelo's suggestion.
Fixes: 96ca468b86 ("sctp: check invalid value of length parameter in error cause")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 303d0403b8 ]
As of the below commit, udp sockets bound to a specific address can
coexist with one bound to the any addr for the same port.
The commit also phased out the use of socket hashing based only on
port (hslot), in favor of always hashing on {addr, port} (hslot2).
The change broke the following behavior with disconnect (AF_UNSPEC):
server binds to 0.0.0.0:1337
server connects to 127.0.0.1:80
server disconnects
client connects to 127.0.0.1:1337
client sends "hello"
server reads "hello" // times out, packet did not find sk
On connect the server acquires a specific source addr suitable for
routing to its destination. On disconnect it reverts to the any addr.
The connect call triggers a rehash to a different hslot2. On
disconnect, add the same to return to the original hslot2.
Skip this step if the socket is going to be unhashed completely.
Fixes: 4cdeeee925 ("net: udp: prefer listeners bound to an address")
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 379349e9bc ]
This reverts commit ba27b4cdaa
Ahmed reported ouf-of-order issues bisected to commit ba27b4cdaa
("net: dev: introduce support for sch BYPASS for lockless qdisc").
I can't find any working solution other than a plain revert.
This will introduce some minor performance regressions for
pfifo_fast qdisc. I plan to address them in net-next with more
indirect call wrapper boilerplate for qdiscs.
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Fixes: ba27b4cdaa ("net: dev: introduce support for sch BYPASS for lockless qdisc")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af6565adb0 ]
If an event is added while the rdma workqueue is being destroyed
it could lead to several races, list corruption, null pointer
dereference during queue_work or init_queue.
This fixes the race between the two flows which can occur during
shutdown.
A kref object and a completion object are added to the rdma_dev
structure, these are initialized before the workqueue is created.
The refcnt is used to indicate work is being added to the
workqueue and ensures the cleanup flow won't start while we're in
the middle of adding the event.
Once the work is added, the refcnt is decreased and the cleanup flow
is safe to run.
Fixes: cee9fbd8e2 ("qede: Add qedr framework")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3331d2fe3 ]
The PN544 driver checks the "enable" polarity during of driver's probe and
it's doing that by turning ON and OFF NFC with different polarities until
enabling succeeds. It takes some time for the hardware to power-down, and
thus, to deassert the IRQ that is raised by turning ON the hardware.
Since the delay after last power-down of the polarity-checking process is
missed in the code, the interrupt may trigger immediately after installing
the IRQ handler (right after the checking is done), which results in IRQ
handler trying to touch the disabled HW and ends with marking NFC as
'DEAD' during of the driver's probe:
pn544_hci_i2c 1-002a: NFC: nfc_en polarity : active high
pn544_hci_i2c 1-002a: NFC: invalid len byte
shdlc: llc_shdlc_recv_frame: NULL Frame -> link is dead
This patch fixes the occasional NFC initialization failure on Nexus 7
device.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06f5201c63 ]
Current code doesn't check if tcp sequence number is starting from (/after)
1st record's start sequnce number. It only checks if seq number is before
1st record's end sequnce number. This problem will always be a possibility
in re-transmit case. If a record which belongs to a requested seq number is
already deleted, tls_get_record will start looking into list and as per the
check it will look if seq number is before the end seq of 1st record, which
will always be true and will return 1st record always, it should in fact
return NULL.
As part of the fix, start looking each record only if the sequence number
lies in the list else return NULL.
There is one more check added, driver look for the start marker record to
handle tcp packets which are before the tls offload start sequence number,
hence return 1st record if the record is tls start marker and seq number is
before the 1st record's starting sequence number.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
