commit 042745ee53 upstream.
Commit 3a0f9aaee0 ("dm raid: round region_size to power of two")
intended to make sure that the default region size is a power of two.
However, the logic in that commit is incorrect and sets the variable
region_size to 0 or 1, depending on whether min_region_size is a power
of two.
Fix this logic, using roundup_pow_of_two(), so that region_size is
properly rounded up to the next power of two.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 3a0f9aaee0 ("dm raid: round region_size to power of two")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0dc3c8bc1 upstream.
When using nested btrees, the top leaves of the top levels contain
block addresses for the root of the next tree down. If we shadow a
shared leaf node the leaf values (sub tree roots) should be incremented
accordingly.
This is only an issue if there is metadata sharing in the top levels.
Which only occurs if metadata snapshots are being used (as is possible
with dm-thinp). And could result in a block from the thinp metadata
snap being reused early, thus corrupting the thinp metadata snap.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad83dbd974 upstream.
The "adl_pci7x3x" driver replaced the "adl_pci7230" and "adl_pci7432"
drivers in commits 8f567c373c ("staging: comedi: new adl_pci7x3x
driver") and 657f77d173 ("staging: comedi: remove adl_pci7230 and
adl_pci7432 drivers"). Although the new driver code agrees with the
user manuals for the respective boards, digital outputs stopped working
on the PCI-7230. This has 16 digital output channels and the previous
adl_pci7230 driver shifted the 16 bit output state left by 16 bits
before writing to the hardware register. The new adl_pci7x3x driver
doesn't do that. Fix it in `adl_pci7x3x_do_insn_bits()` by checking
for the special case of the subdevice having only 16 channels and
duplicating the 16 bit output state into both halves of the 32-bit
register. That should work both for what the board actually does and
for what the user manual says it should do.
Fixes: 8f567c373c ("staging: comedi: new adl_pci7x3x driver")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a30e577c96 upstream.
In btrfs_evict_inode, we properly truncate the page cache for evicted
inodes but then we call btrfs_wait_ordered_range for every inode as well.
It's the right thing to do for regular files but results in incorrect
behavior for device inodes for block devices.
filemap_fdatawrite_range gets called with inode->i_mapping which gets
resolved to the block device inode before getting passed to
wbc_attach_fdatawrite_inode and ultimately to inode_to_bdi. What happens
next depends on whether there's an open file handle associated with the
inode. If there is, we write to the block device, which is unexpected
behavior. If there isn't, we through normally and inode->i_data is used.
We can also end up racing against open/close which can result in crashes
when i_mapping points to a block device inode that has been closed.
Since there can't be any page cache associated with special file inodes,
it's safe to skip the btrfs_wait_ordered_range call entirely and avoid
the problem.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=100911
Tested-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c8f7710c1 upstream.
The previous fix of pxa library support, which was introduced to fix the
library dependency, broke the previous SoC behavior, where a machine
code binding pxa2xx-ac97 with a coded relied on :
- sound/soc/pxa/pxa2xx-ac97.c
- sound/soc/codecs/XXX.c
For example, the mioa701_wm9713.c machine code is currently broken. The
"select ARM" statement wrongly selects the soc/arm/pxa2xx-ac97 for
compilation, as per an unfortunate fate SND_PXA2XX_AC97 is both declared
in sound/arm/Kconfig and sound/soc/pxa/Kconfig.
Fix this by ensuring that SND_PXA2XX_SOC correctly triggers the correct
pxa2xx-ac97 compilation.
Fixes: 846172dfe3 ("ASoC: fix SND_PXA2XX_LIB Kconfig warning")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 225db5762d upstream.
When OSS emulation is loaded on ISA SB AWE32 chip, we get now kernel
warnings like:
WARNING: CPU: 0 PID: 2791 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x51/0x80()
sysfs: cannot create duplicate filename '/devices/isa/sbawe.0/sound/card0/seq-oss-0-0'
It's because both emux synth and opl3 drivers try to register their
OSS device object with the same static index number 0. This hasn't
been a big problem until the recent rewrite of device management code
(that exposes sysfs at the same time), but it's been an obvious bug.
This patch works around it just by using a different index number of
emux synth object. There can be a more elegant way to fix, but it's
enough for now, as this code won't be touched so often, in anyway.
Reported-and-tested-by: Michael Shell <list1@michaelshell.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f84a8990e upstream.
SunDong reported the following on
https://bugzilla.kernel.org/show_bug.cgi?id=103841
I think I find a linux bug, I have the test cases is constructed. I
can stable recurring problems in fedora22(4.0.4) kernel version,
arch for x86_64. I construct transparent huge page, when the parent
and child process with MAP_SHARE, MAP_PRIVATE way to access the same
huge page area, it has the opportunity to lead to huge page copy on
write failure, and then it will munmap the child corresponding mmap
area, but then the child mmap area with VM_MAYSHARE attributes, child
process munmap this area can trigger VM_BUG_ON in set_vma_resv_flags
functions (vma - > vm_flags & VM_MAYSHARE).
There were a number of problems with the report (e.g. it's hugetlbfs that
triggers this, not transparent huge pages) but it was fundamentally
correct in that a VM_BUG_ON in set_vma_resv_flags() can be triggered that
looks like this
vma ffff8804651fd0d0 start 00007fc474e00000 end 00007fc475e00000
next ffff8804651fd018 prev ffff8804651fd188 mm ffff88046b1b1800
prot 8000000000000027 anon_vma (null) vm_ops ffffffff8182a7a0
pgoff 0 file ffff88106bdb9800 private_data (null)
flags: 0x84400fb(read|write|shared|mayread|maywrite|mayexec|mayshare|dontexpand|hugetlb)
------------
kernel BUG at mm/hugetlb.c:462!
SMP
Modules linked in: xt_pkttype xt_LOG xt_limit [..]
CPU: 38 PID: 26839 Comm: map Not tainted 4.0.4-default #1
Hardware name: Dell Inc. PowerEdge R810/0TT6JF, BIOS 2.7.4 04/26/2012
set_vma_resv_flags+0x2d/0x30
The VM_BUG_ON is correct because private and shared mappings have
different reservation accounting but the warning clearly shows that the
VMA is shared.
When a private COW fails to allocate a new page then only the process
that created the VMA gets the page -- all the children unmap the page.
If the children access that data in the future then they get killed.
The problem is that the same file is mapped shared and private. During
the COW, the allocation fails, the VMAs are traversed to unmap the other
private pages but a shared VMA is found and the bug is triggered. This
patch identifies such VMAs and skips them.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: SunDong <sund_sky@126.com>
Reviewed-by: Michal Hocko <mhocko@suse.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02bc933ebb upstream.
On Intel Baytrail, there is case when interrupt handler get called, no SPI
message is captured. The RX FIFO is indeed empty when RX timeout pending
interrupt (SSSR_TINT) happens.
Use the BIOS version where both HSUART and SPI are on the same IRQ. Both
drivers are using IRQF_SHARED when calling the request_irq function. When
running two separate and independent SPI and HSUART application that
generate data traffic on both components, user will see messages like
below on the console:
pxa2xx-spi pxa2xx-spi.0: bad message state in interrupt handler
This commit will fix this by first checking Receiver Time-out Interrupt,
if it is disabled, ignore the request and return without servicing.
Signed-off-by: Tan, Jui Nee <jui.nee.tan@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a394d63519 upstream.
Actually, spi_master_put() after spi_alloc_master() must _not_ be followed
by kfree(). The memory is already freed with the call to spi_master_put()
through spi_master_class, which registers a release function. Calling both
spi_master_put() and kfree() results in often nasty (and delayed) crashes
elsewhere in the kernel, often in the networking stack.
This reverts commit eb4af0f534.
Link to patch and concerns: https://lkml.org/lkml/2012/9/3/269
or
http://lkml.iu.edu/hypermail/linux/kernel/1209.0/00790.html
Alexey Klimov: This revert becomes valid after
94c69f765f when spi-imx.c
has been fixed and there is no need to call kfree() so comment
for spi_alloc_master() should be fixed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b34a166f2 upstream.
Currently there is a number of issues preventing PVHVM Xen guests from
doing successful kexec/kdump:
- Bound event channels.
- Registered vcpu_info.
- PIRQ/emuirq mappings.
- shared_info frame after XENMAPSPACE_shared_info operation.
- Active grant mappings.
Basically, newly booted kernel stumbles upon already set up Xen
interfaces and there is no way to reestablish them. In Xen-4.7 a new
feature called 'soft reset' is coming. A guest performing kexec/kdump
operation is supposed to call SCHEDOP_shutdown hypercall with
SHUTDOWN_soft_reset reason before jumping to new kernel. Hypervisor
(with some help from toolstack) will do full domain cleanup (but
keeping its memory and vCPU contexts intact) returning the guest to
the state it had when it was first booted and thus allowing it to
start over.
Doing SHUTDOWN_soft_reset on Xen hypervisors which don't support it is
probably OK as by default all unknown shutdown reasons cause domain
destroy with a message in toolstack log: 'Unknown shutdown reason code
5. Destroying domain.' which gives a clue to what the problem is and
eliminates false expectations.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab76f7b4ab upstream.
Unused space between the end of __ex_table and the start of
rodata can be left W+x in the kernel page tables. Extend the
setting of the NX bit to cover this gap by starting from
text_end rather than rodata_start.
Before:
---[ High Kernel Mapping ]---
0xffffffff80000000-0xffffffff81000000 16M pmd
0xffffffff81000000-0xffffffff81600000 6M ro PSE GLB x pmd
0xffffffff81600000-0xffffffff81754000 1360K ro GLB x pte
0xffffffff81754000-0xffffffff81800000 688K RW GLB x pte
0xffffffff81800000-0xffffffff81a00000 2M ro PSE GLB NX pmd
0xffffffff81a00000-0xffffffff81b3b000 1260K ro GLB NX pte
0xffffffff81b3b000-0xffffffff82000000 4884K RW GLB NX pte
0xffffffff82000000-0xffffffff82200000 2M RW PSE GLB NX pmd
0xffffffff82200000-0xffffffffa0000000 478M pmd
After:
---[ High Kernel Mapping ]---
0xffffffff80000000-0xffffffff81000000 16M pmd
0xffffffff81000000-0xffffffff81600000 6M ro PSE GLB x pmd
0xffffffff81600000-0xffffffff81754000 1360K ro GLB x pte
0xffffffff81754000-0xffffffff81800000 688K RW GLB NX pte
0xffffffff81800000-0xffffffff81a00000 2M ro PSE GLB NX pmd
0xffffffff81a00000-0xffffffff81b3b000 1260K ro GLB NX pte
0xffffffff81b3b000-0xffffffff82000000 4884K RW GLB NX pte
0xffffffff82000000-0xffffffff82200000 2M RW PSE GLB NX pmd
0xffffffff82200000-0xffffffffa0000000 478M pmd
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1443704662-3138-1-git-send-email-sds@tycho.nsa.gov
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2922422c4 upstream.
The cpu feature flags are not ever going to change, so warning
everytime can cause a lot of kernel log spam
(in our case more than 10GB/hour).
The warning seems to only occur when nested virtualization is
enabled, so it's probably triggered by a KVM bug. This is a
sensible and safe change anyway, and the KVM bug fix might not
be suitable for stable releases anyway.
Signed-off-by: Dirk Mueller <dmueller@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d7c631d92 upstream.
The APIC LVTT register is MMIO mapped but the TSC_DEADLINE register is an
MSR. The write to the TSC_DEADLINE MSR is not serializing, so it's not
guaranteed that the write to LVTT has reached the APIC before the
TSC_DEADLINE MSR is written. In such a case the write to the MSR is
ignored and as a consequence the local timer interrupt never fires.
The SDM decribes this issue for xAPIC and x2APIC modes. The
serialization methods recommended by the SDM differ.
xAPIC:
"1. Memory-mapped write to LVT Timer Register, setting bits 18:17 to 10b.
2. WRMSR to the IA32_TSC_DEADLINE MSR a value much larger than current time-stamp counter.
3. If RDMSR of the IA32_TSC_DEADLINE MSR returns zero, go to step 2.
4. WRMSR to the IA32_TSC_DEADLINE MSR the desired deadline."
x2APIC:
"To allow for efficient access to the APIC registers in x2APIC mode,
the serializing semantics of WRMSR are relaxed when writing to the
APIC registers. Thus, system software should not use 'WRMSR to APIC
registers in x2APIC mode' as a serializing instruction. Read and write
accesses to the APIC registers will occur in program order. A WRMSR to
an APIC register may complete before all preceding stores are globally
visible; software can prevent this by inserting a serializing
instruction, an SFENCE, or an MFENCE before the WRMSR."
The xAPIC method is to just wait for the memory mapped write to hit
the LVTT by checking whether the MSR write has reached the hardware.
There is no reason why a proper MFENCE after the memory mapped write would
not do the same. Andi Kleen confirmed that MFENCE is sufficient for the
xAPIC case as well.
Issue MFENCE before writing to the TSC_DEADLINE MSR. This can be done
unconditionally as all CPUs which have TSC_DEADLINE also have MFENCE
support.
[ tglx: Massaged the changelog ]
Signed-off-by: Shaohua Li <shli@fb.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: <Kernel-team@fb.com>
Cc: <lenb@kernel.org>
Cc: <fenghua.yu@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/20150909041352.GA2059853@devbig257.prn2.facebook.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe2b592173 upstream.
wf_unregister_client() increments the client count when a client
unregisters. That is obviously incorrect. Decrement that client count
instead.
Fixes: 75722d3992 ("[PATCH] ppc64: Thermal control for SMU based machines")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a077224fd3 upstream.
While working on the 32-bit ARM port of UEFI, I noticed a strange
corruption in the kernel log. The following snprintf() statement
(in drivers/firmware/efi/efi.c:efi_md_typeattr_format())
snprintf(pos, size, "|%3s|%2s|%2s|%2s|%3s|%2s|%2s|%2s|%2s]",
was producing the following output in the log:
| | | | | |WB|WT|WC|UC]
| | | | | |WB|WT|WC|UC]
| | | | | |WB|WT|WC|UC]
|RUN| | | | |WB|WT|WC|UC]*
|RUN| | | | |WB|WT|WC|UC]*
| | | | | |WB|WT|WC|UC]
|RUN| | | | |WB|WT|WC|UC]*
| | | | | |WB|WT|WC|UC]
|RUN| | | | | | | |UC]
|RUN| | | | | | | |UC]
As it turns out, this is caused by incorrect code being emitted for
the string() function in lib/vsprintf.c. The following code
if (!(spec.flags & LEFT)) {
while (len < spec.field_width--) {
if (buf < end)
*buf = ' ';
++buf;
}
}
for (i = 0; i < len; ++i) {
if (buf < end)
*buf = *s;
++buf; ++s;
}
while (len < spec.field_width--) {
if (buf < end)
*buf = ' ';
++buf;
}
when called with len == 0, triggers an issue in the GCC SRA optimization
pass (Scalar Replacement of Aggregates), which handles promotion of signed
struct members incorrectly. This is a known but as yet unresolved issue.
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=65932). In this particular
case, it is causing the second while loop to be executed erroneously a
single time, causing the additional space characters to be printed.
So disable the optimization by passing -fno-ipa-sra.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 537b604c8b upstream.
b9d5c6b7ef ("[SCSI] cleanup setting task state in
scsi_error_handler()") has introduced a race between scsi_error_handler
and scsi_host_dev_release resulting in the hang when the device goes
away because scsi_error_handler might miss a wake up:
CPU0 CPU1
scsi_error_handler scsi_host_dev_release
kthread_stop()
kthread_should_stop()
test_bit(KTHREAD_SHOULD_STOP)
set_bit(KTHREAD_SHOULD_STOP)
wake_up_process()
wait_for_completion()
set_current_state(TASK_INTERRUPTIBLE)
schedule()
The most straightforward solution seems to be to invert the ordering of
the set_current_state and kthread_should_stop.
The issue has been noticed during reboot test on a 3.0 based kernel but
the current code seems to be affected in the same way.
[jejb: additional comment added]
Reported-and-debugged-by: Mike Mayer <Mike.Meyer@teradata.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93e3bce628 upstream.
The warning message in prepend_path is unclear and outdated. It was
added as a warning that the mechanism for generating names of pseudo
files had been removed from prepend_path and d_dname should be used
instead. Unfortunately the warning reads like a general warning,
making it unclear what to do with it.
Remove the warning. The transition it was added to warn about is long
over, and I added code several years ago which in rare cases causes
the warning to fire on legitimate code, and the warning is now firing
and scaring people for no good reason.
Reported-by: Ivan Delalande <colona@arista.com>
Reported-by: Omar Sandoval <osandov@osandov.com>
Fixes: f48cfddc67 ("vfs: In d_path don't call d_dname on a mount point")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
[ vlee: Backported to 3.10. Adjusted context. ]
Signed-off-by: Vinson Lee <vlee@twitter.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41fc014332 ]
dump_rules returns skb length and not error.
But when family == AF_UNSPEC, the caller of dump_rules
assumes that it returns an error. Hence, when family == AF_UNSPEC,
we continue trying to dump on -EMSGSIZE errors resulting in
incorrect dump idx carried between skbs belonging to the same dump.
This results in fib rule dump always only dumping rules that fit
into the first skb.
This patch fixes dump_rules to return error so that we exit correctly
and idx is correctly maintained between skbs that are part of the
same dump.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8e2d61e0ae ]
Consider sctp module is unloaded and is being requested because an user
is creating a sctp socket.
During initialization, sctp will add the new protocol type and then
initialize pernet subsys:
status = sctp_v4_protosw_init();
if (status)
goto err_protosw_init;
status = sctp_v6_protosw_init();
if (status)
goto err_v6_protosw_init;
status = register_pernet_subsys(&sctp_net_ops);
The problem is that after those calls to sctp_v{4,6}_protosw_init(), it
is possible for userspace to create SCTP sockets like if the module is
already fully loaded. If that happens, one of the possible effects is
that we will have readers for net->sctp.local_addr_list list earlier
than expected and sctp_net_init() does not take precautions while
dealing with that list, leading to a potential panic but not limited to
that, as sctp_sock_init() will copy a bunch of blank/partially
initialized values from net->sctp.
The race happens like this:
CPU 0 | CPU 1
socket() |
__sock_create | socket()
inet_create | __sock_create
list_for_each_entry_rcu( |
answer, &inetsw[sock->type], |
list) { | inet_create
/* no hits */ |
if (unlikely(err)) { |
... |
request_module() |
/* socket creation is blocked |
* the module is fully loaded |
*/ |
sctp_init |
sctp_v4_protosw_init |
inet_register_protosw |
list_add_rcu(&p->list, |
last_perm); |
| list_for_each_entry_rcu(
| answer, &inetsw[sock->type],
sctp_v6_protosw_init | list) {
| /* hit, so assumes protocol
| * is already loaded
| */
| /* socket creation continues
| * before netns is initialized
| */
register_pernet_subsys |
Simply inverting the initialization order between
register_pernet_subsys() and sctp_v4_protosw_init() is not possible
because register_pernet_subsys() will create a control sctp socket, so
the protocol must be already visible by then. Deferring the socket
creation to a work-queue is not good specially because we loose the
ability to handle its errors.
So, as suggested by Vlad, the fix is to split netns initialization in
two moments: defaults and control socket, so that the defaults are
already loaded by when we register the protocol, while control socket
initialization is kept at the same moment it is today.
Fixes: 4db67e8086 ("sctp: Make the address lists per network namespace")
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 25b4a44c19 ]
In the IPv6 multicast routing code the mrt_lock was not being released
correctly in the MFC iterator, as a result adding or deleting a MIF would
cause a hang because the mrt_lock could not be acquired.
This fix is a copy of the code for the IPv4 case and ensures that the lock
is released correctly.
Signed-off-by: Richard Laing <richard.laing@alliedtelesis.co.nz>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e41b0bedba ]
We previously register IPPROTO_ROUTING offload under inet6_add_offload(),
but in error path, we try to unregister it with inet_del_offload(). This
doesn't seem correct, it should actually be inet6_del_offload(), also
ipv6_exthdrs_offload_exit() from that commit seems rather incorrect (it
also uses rthdr_offload twice), but it got removed entirely later on.
Fixes: 3336288a9f ("ipv6: Switch to using new offload infrastructure.")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f50791ac1a ]
It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in
usbnet_stop(), but its value should be read before it is cleared
when dev->flags is set to 0.
The problem was spotted and the fix was provided by
Oliver Neukum <oneukum@suse.de>.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4257295ba ]
When a tunnel is deleted, the cached dst entry should be released.
This problem may prevent the removal of a netns (seen with a x-netns IPv6
gre tunnel):
unregister_netdevice: waiting for lo to become free. Usage count = 3
CC: Dmitry Kozlov <xeb@mail.ru>
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: huaibin Wang <huaibin.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 468b732b6f ]
"len" is a signed integer. We check that len is not negative, so it
goes from zero to INT_MAX. PAGE_SIZE is unsigned long so the comparison
is type promoted to unsigned long. ULONG_MAX - 4095 is a higher than
INT_MAX so the condition can never be true.
I don't know if this is harmful but it seems safe to limit "len" to
INT_MAX - 4095.
Fixes: a8c879a7ee ('RDS: Info and stats')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0848f6428b ]
When ip_frag_queue() computes positions, it assumes that the passed
sk_buff does not contain L2 headers.
However, when PACKET_FANOUT_FLAG_DEFRAG is used, IP reassembly
functions can be called on outgoing packets that contain L2 headers.
Also, IPv4 checksum is not corrected after reassembly.
Fixes: 7736d33f42 ("packet: Add pre-defragmentation support for ipv4 fanouts.")
Signed-off-by: Edward Hyunkoo Jee <edjee@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06f6d1094a ]
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[ 908.963051] eql: event: 9
[ 908.963052] eql: IFF_SLAVE
[ 908.963054] eql: event: 2
[ 908.963056] eql: IFF_SLAVE
[ 908.963058] eql: event: 6
[ 908.963059] eql: IFF_SLAVE
[ 908.963110] bond0: Releasing active interface eql
[ 908.976168] bond0: Destroying bond bond0
[ 908.976266] bond0 (unregistering): Released all slaves
[ 908.984097] ------------[ cut here ]------------
[ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[ 908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]
[ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O
4.2.0-rc2+ #8
[ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[ 908.984181] Call Trace:
[ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[ 908.984225] [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[ 908.984228] [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[ 908.984244] [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[ 908.984247] ---[ end trace 7c006ed4abbef24b ]---
Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f939981492 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3dd ("bonding: Manage /proc/net/bonding/ entries from
the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03645a11a5 ]
ip6_datagram_connect() is doing a lot of socket changes without
socket being locked.
This looks wrong, at least for udp_lib_rehash() which could corrupt
lists because of concurrent udp_sk(sk)->udp_portaddr_hash accesses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd98e9419d ]
Commit 79901317ce ("n_tty: Don't flush buffer when closing ldisc"),
first merged in kernel release 3.10, caused the following regression
in the Gigaset M101 driver:
Before that commit, when closing the N_TTY line discipline in
preparation to switching to N_GIGASET_M101, receive_room would be
reset to a non-zero value by the call to n_tty_flush_buffer() in
n_tty's close method. With the removal of that call, receive_room
might be left at zero, blocking data reception on the serial line.
The present patch fixes that regression by setting receive_room
to an appropriate value in the ldisc open method.
Fixes: 79901317ce ("n_tty: Don't flush buffer when closing ldisc")
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ebc784625 ]
Since the mdb add/del code was introduced there have been 2 br_mdb_notify
calls when doing br_mdb_add() resulting in 2 notifications on each add.
Example:
Command: bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent
Before patch:
root@debian:~# bridge monitor all
[MDB]dev br0 port eth1 grp 239.0.0.1 permanent
[MDB]dev br0 port eth1 grp 239.0.0.1 permanent
After patch:
root@debian:~# bridge monitor all
[MDB]dev br0 port eth1 grp 239.0.0.1 permanent
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: cfd5675435 ("bridge: add support of adding and deleting mdb entries")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0a2a66024 ]
The commit 738ac1ebb9 ("net: Clone
skb before setting peeked flag") introduced a use-after-free bug
in skb_recv_datagram. This is because skb_set_peeked may create
a new skb and free the existing one. As it stands the caller will
continue to use the old freed skb.
This patch fixes it by making skb_set_peeked return the new skb
(or the old one if unchanged).
Fixes: 738ac1ebb9 ("net: Clone skb before setting peeked flag")
Reported-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Brenden Blanco <bblanco@plumgrid.com>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89c22d8c3b ]
When we calculate the checksum on the recv path, we store the
result in the skb as an optimisation in case we need the checksum
again down the line.
This is in fact bogus for the MSG_PEEK case as this is done without
any locking. So multiple threads can peek and then store the result
to the same skb, potentially resulting in bogus skb states.
This patch fixes this by only storing the result if the skb is not
shared. This preserves the optimisations for the few cases where
it can be done safely due to locking or other reasons, e.g., SIOCINQ.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 738ac1ebb9 ]
Shared skbs must not be modified and this is crucial for broadcast
and/or multicast paths where we use it as an optimisation to avoid
unnecessary cloning.
The function skb_recv_datagram breaks this rule by setting peeked
without cloning the skb first. This causes funky races which leads
to double-free.
This patch fixes this by cloning the skb and replacing the skb
in the list when setting skb->peeked.
Fixes: a59322be07 ("[UDP]: Only increment counter on first peek/recv")
Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c17d27c36 ]
Incoming packet should be either in backlog queue or
in RCU read-side section. Otherwise, the final sequence of
flush_backlog() and synchronize_net() may miss packets
that can run without device reference:
CPU 1 CPU 2
skb->dev: no reference
process_backlog:__skb_dequeue
process_backlog:local_irq_enable
on_each_cpu for
flush_backlog => IPI(hardirq): flush_backlog
- packet not found in backlog
CPU delayed ...
synchronize_net
- no ongoing RCU
read-side sections
netdev_run_todo,
rcu_barrier: no
ongoing callbacks
__netif_receive_skb_core:rcu_read_lock
- too late
free dev
process packet for freed dev
Fixes: 6e583ce524 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f1158b74e5 ]
Since commit b0e9a30dd6 ("bridge: Add vlan id to multicast groups")
there's a check in br_ip_equal() for a matching vlan id, but the mdb
functions were not modified to use (or at least zero it) so when an
entry was added it would have a garbage vlan id (from the local br_ip
variable in __br_mdb_add/del) and this would prevent it from being
matched and also deleted. So zero out the whole local ip var to protect
ourselves from future changes and also to fix the current bug, since
there's no vlan id support in the mdb uapi - use always vlan id 0.
Example before patch:
root@debian:~# bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb del dev br0 port eth1 grp 239.0.0.1 permanent
RTNETLINK answers: Invalid argument
After patch:
root@debian:~# bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb del dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Fixes: b0e9a30dd6 ("bridge: Add vlan id to multicast groups")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fdd75ea8df ]
Calling connect() with an AF_TIPC socket would trigger a series
of error messages from SELinux along the lines of:
SELinux: Invalid class 0
type=AVC msg=audit(1434126658.487:34500): avc: denied { <unprintable> }
for pid=292 comm="kworker/u16:5" scontext=system_u:system_r:kernel_t:s0
tcontext=system_u:object_r:unlabeled_t:s0 tclass=<unprintable>
permissive=0
This was due to a failure to initialize the security state of the new
connection sock by the tipc code, leaving it with junk in the security
class field and an unlabeled secid. Add a call to security_sk_clone()
to inherit the security state from the parent socket.
Reported-by: Tim Shearer <tim.shearer@overturenetworks.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c938d22c8 ]
Before commit daad151263 ("ipv6: Make ipv6_is_mld() inline and use it
from ip6_mc_input().") MLD packets were only processed locally. After the
change, a copy of MLD packet goes through ip6_mr_input, causing
MRT6MSG_NOCACHE message to be generated to user space.
Make MLD packet only processed locally.
Fixes: daad151263 ("ipv6: Make ipv6_is_mld() inline and use it from ip6_mc_input().")
Signed-off-by: Hermin Anggawijaya <hermin.anggawijaya@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f7352bf21 upstream.
x86 has variable length encoding. x86 JIT compiler is trying
to pick the shortest encoding for given bpf instruction.
While doing so the jump targets are changing, so JIT is doing
multiple passes over the program. Typical program needs 3 passes.
Some very short programs converge with 2 passes. Large programs
may need 4 or 5. But specially crafted bpf programs may hit the
pass limit and if the program converges on the last iteration
the JIT compiler will be producing an image full of 'int 3' insns.
Fix this corner case by doing final iteration over bpf program.
Fixes: 0a14842f5a ("net: filter: Just In Time compiler for x86-64")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59c816c1f2 upstream.
This code in vhost_scsi_make_tpg() is confusing because we limit "tpgt"
to UINT_MAX but the data type of "tpg->tport_tpgt" and that is a u16.
I looked at the context and it turns out that in
vhost_scsi_set_endpoint(), "tpg->tport_tpgt" is used as an offset into
the vs_tpg[] array which has VHOST_SCSI_MAX_TARGET (256) elements so
anything higher than 255 then it is invalid. I have made that the limit
now.
In vhost_scsi_send_evt() we mask away values higher than 255, but now
that the limit has changed, we don't need the mask.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ The affected function was renamed to vhost_scsi_make_tpg before
the vulnerability was announced, I ported it to 3.10 stable and
changed the code in function tcm_vhost_make_tpg]
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d45a02d01 upstream.
->auto_asconf_splist is per namespace and mangled by functions like
sctp_setsockopt_auto_asconf() which doesn't guarantee any serialization.
Also, the call to inet_sk_copy_descendant() was backuping
->auto_asconf_list through the copy but was not honoring
->do_auto_asconf, which could lead to list corruption if it was
different between both sockets.
This commit thus fixes the list handling by using ->addr_wq_lock
spinlock to protect the list. A special handling is done upon socket
creation and destruction for that. Error handlig on sctp_init_sock()
will never return an error after having initialized asconf, so
sctp_destroy_sock() can be called without addrq_wq_lock. The lock now
will be take on sctp_close_sock(), before locking the socket, so we
don't do it in inverse order compared to sctp_addr_wq_timeout_handler().
Instead of taking the lock on sctp_sock_migrate() for copying and
restoring the list values, it's preferred to avoid rewritting it by
implementing sctp_copy_descendant().
Issue was found with a test application that kept flipping sysctl
default_auto_asconf on and off, but one could trigger it by issuing
simultaneous setsockopt() calls on multiple sockets or by
creating/destroying sockets fast enough. This is only triggerable
locally.
Fixes: 9f7d653b67 ("sctp: Add Auto-ASCONF support (core).")
Reported-by: Ji Jianwen <jiji@redhat.com>
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[wangkai: backport to 3.10: adjust context]
Signed-off-by: Wang Kai <morgan.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cb74be6fd upstream.
Pages looked up by __hfs_bnode_create() (called by hfs_bnode_create() and
hfs_bnode_find() for finding or creating pages corresponding to an inode)
are immediately kmap()'ed and used (both read and write) and kunmap()'ed,
and should not be page_cache_release()'ed until hfs_bnode_free().
This patch fixes a problem I first saw in July 2012: merely running "du"
on a large hfsplus-mounted directory a few times on a reasonably loaded
system would get the hfsplus driver all confused and complaining about
B-tree inconsistencies, and generates a "BUG: Bad page state". Most
recently, I can generate this problem on up-to-date Fedora 22 with shipped
kernel 4.0.5, by running "du /" (="/" + "/home" + "/mnt" + other smaller
mounts) and "du /mnt" simultaneously on two windows, where /mnt is a
lightly-used QEMU VM image of the full Mac OS X 10.9:
$ df -i / /home /mnt
Filesystem Inodes IUsed IFree IUse% Mounted on
/dev/mapper/fedora-root 3276800 551665 2725135 17% /
/dev/mapper/fedora-home 52879360 716221 52163139 2% /home
/dev/nbd0p2 4294967295 1387818 4293579477 1% /mnt
After applying the patch, I was able to run "du /" (60+ times) and "du
/mnt" (150+ times) continuously and simultaneously for 6+ hours.
There are many reports of the hfsplus driver getting confused under load
and generating "BUG: Bad page state" or other similar issues over the
years. [1]
The unpatched code [2] has always been wrong since it entered the kernel
tree. The only reason why it gets away with it is that the
kmap/memcpy/kunmap follow very quickly after the page_cache_release() so
the kernel has not had a chance to reuse the memory for something else,
most of the time.
The current RW driver appears to have followed the design and development
of the earlier read-only hfsplus driver [3], where-by version 0.1 (Dec
2001) had a B-tree node-centric approach to
read_cache_page()/page_cache_release() per bnode_get()/bnode_put(),
migrating towards version 0.2 (June 2002) of caching and releasing pages
per inode extents. When the current RW code first entered the kernel [2]
in 2005, there was an REF_PAGES conditional (and "//" commented out code)
to switch between B-node centric paging to inode-centric paging. There
was a mistake with the direction of one of the REF_PAGES conditionals in
__hfs_bnode_create(). In a subsequent "remove debug code" commit [4], the
read_cache_page()/page_cache_release() per bnode_get()/bnode_put() were
removed, but a page_cache_release() was mistakenly left in (propagating
the "REF_PAGES <-> !REF_PAGE" mistake), and the commented-out
page_cache_release() in bnode_release() (which should be spanned by
!REF_PAGES) was never enabled.
References:
[1]:
Michael Fox, Apr 2013
http://www.spinics.net/lists/linux-fsdevel/msg63807.html
("hfsplus volume suddenly inaccessable after 'hfs: recoff %d too large'")
Sasha Levin, Feb 2015
http://lkml.org/lkml/2015/2/20/85 ("use after free")
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/740814https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1027887https://bugzilla.kernel.org/show_bug.cgi?id=42342https://bugzilla.kernel.org/show_bug.cgi?id=63841https://bugzilla.kernel.org/show_bug.cgi?id=78761
[2]:
http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/\
fs/hfs/bnode.c?id=d1081202f1d0ee35ab0beb490da4b65d4bc763db
commit d1081202f1d0ee35ab0beb490da4b65d4bc763db
Author: Andrew Morton <akpm@osdl.org>
Date: Wed Feb 25 16:17:36 2004 -0800
[PATCH] HFS rewrite
http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/\
fs/hfsplus/bnode.c?id=91556682e0bf004d98a529bf829d339abb98bbbd
commit 91556682e0bf004d98a529bf829d339abb98bbbd
Author: Andrew Morton <akpm@osdl.org>
Date: Wed Feb 25 16:17:48 2004 -0800
[PATCH] HFS+ support
[3]:
http://sourceforge.net/projects/linux-hfsplus/http://sourceforge.net/projects/linux-hfsplus/files/Linux%202.4.x%20patch/hfsplus%200.1/http://sourceforge.net/projects/linux-hfsplus/files/Linux%202.4.x%20patch/hfsplus%200.2/http://linux-hfsplus.cvs.sourceforge.net/viewvc/linux-hfsplus/linux/\
fs/hfsplus/bnode.c?r1=1.4&r2=1.5
Date: Thu Jun 6 09:45:14 2002 +0000
Use buffer cache instead of page cache in bnode.c. Cache inode extents.
[4]:
http://git.kernel.org/cgit/linux/kernel/git/\
stable/linux-stable.git/commit/?id=a5e3985fa014029eb6795664c704953720cc7f7d
commit a5e3985fa0
Author: Roman Zippel <zippel@linux-m68k.org>
Date: Tue Sep 6 15:18:47 2005 -0700
[PATCH] hfs: remove debug code
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Anton Altaparmakov <anton@tuxera.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Sougata Santra <sougata@tuxera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e99b139f1 upstream.
The mlx4 IB driver implementation for ib_query_ah used a wrong offset
(28 instead of 29) when link type is Ethernet. Fixed to use the correct one.
Fixes: fa417f7b52 ('IB/mlx4: Add support for IBoE')
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b135db3e8 upstream.
The pkey mapping for RoCE must remain the default mapping:
VFs:
virtual index 0 = mapped to real index 0 (0xFFFF)
All others indices: mapped to a real pkey index containing an
invalid pkey.
PF:
virtual index i = real index i.
Don't allow users to change these mappings using files found in
sysfs.
Fixes: c1e7e46612 ('IB/mlx4: Add iov directory in sysfs under the ib device')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
