Changes in 4.9.91
MIPS: ralink: Remove ralink_halt()
iio: st_pressure: st_accel: pass correct platform data to init
ALSA: usb-audio: Fix parsing descriptor of UAC2 processing unit
ALSA: aloop: Sync stale timer before release
ALSA: aloop: Fix access to not-yet-ready substream via cable
ALSA: hda/realtek - Always immediately update mute LED with pin VREF
mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occurs
PCI: Add function 1 DMA alias quirk for Highpoint RocketRAID 644L
ahci: Add PCI-id for the Highpoint Rocketraid 644L card
clk: bcm2835: Fix ana->maskX definitions
clk: bcm2835: Protect sections updating shared registers
clk: sunxi-ng: a31: Fix CLK_OUT_* clock ops
Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174
libata: fix length validation of ATAPI-relayed SCSI commands
libata: remove WARN() for DMA or PIO command without data
libata: don't try to pass through NCQ commands to non-NCQ devices
libata: Apply NOLPM quirk to Crucial MX100 512GB SSDs
libata: disable LPM for Crucial BX100 SSD 500GB drive
libata: Enable queued TRIM for Samsung SSD 860
libata: Apply NOLPM quirk to Crucial M500 480 and 960GB SSDs
libata: Make Crucial BX100 500GB LPM quirk apply to all firmware versions
libata: Modify quirks for MX100 to limit NCQ_TRIM quirk to MU01 version
nfsd: remove blocked locks on client teardown
mm/vmalloc: add interfaces to free unmapped page table
x86/mm: implement free pmd/pte page interfaces
mm/khugepaged.c: convert VM_BUG_ON() to collapse fail
mm/thp: do not wait for lock_page() in deferred_split_scan()
mm/shmem: do not wait for lock_page() in shmem_unused_huge_shrink()
drm/vmwgfx: Fix a destoy-while-held mutex problem.
drm/radeon: Don't turn off DP sink when disconnected
drm: udl: Properly check framebuffer mmap offsets
acpi, numa: fix pxm to online numa node associations
ACPI / watchdog: Fix off-by-one error at resource assignment
libnvdimm, {btt, blk}: do integrity setup before add_disk()
brcmfmac: fix P2P_DEVICE ethernet address generation
rtlwifi: rtl8723be: Fix loss of signal
tracing: probeevent: Fix to support minus offset from symbol
mtdchar: fix usage of mtd_ooblayout_ecc()
mtd: nand: fsl_ifc: Fix nand waitfunc return value
mtd: nand: fsl_ifc: Fix eccstat array overflow for IFC ver >= 2.0.0
mtd: nand: fsl_ifc: Read ECCSTAT0 and ECCSTAT1 registers for IFC 2.0
staging: ncpfs: memory corruption in ncp_read_kernel()
can: ifi: Repair the error handling
can: ifi: Check core revision upon probe
can: cc770: Fix stalls on rt-linux, remove redundant IRQ ack
can: cc770: Fix queue stall & dropped RTR reply
can: cc770: Fix use after free in cc770_tx_interrupt()
tty: vt: fix up tabstops properly
selftests/x86/ptrace_syscall: Fix for yet more glibc interference
kvm/x86: fix icebp instruction handling
x86/build/64: Force the linker to use 2MB page size
x86/boot/64: Verify alignment of the LOAD segment
x86/entry/64: Don't use IST entry for #BP stack
perf/x86/intel/uncore: Fix Skylake UPI event format
perf stat: Fix CVS output format for non-supported counters
perf/x86/intel: Don't accidentally clear high bits in bdw_limit_period()
perf/x86/intel/uncore: Fix multi-domain PCI CHA enumeration bug on Skylake servers
iio: ABI: Fix name of timestamp sysfs file
staging: lustre: ptlrpc: kfree used instead of kvfree
selftests, x86, protection_keys: fix wrong offset in siginfo
selftests/x86/protection_keys: Fix syscall NR redefinition warnings
signal/testing: Don't look for __SI_FAULT in userspace
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
selftests: x86: sysret_ss_attrs doesn't build on a PIE build
kbuild: disable clang's default use of -fmerge-all-constants
bpf: skip unnecessary capability check
bpf, x64: increase number of passes
Linux 4.9.91
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
commit 6007b080d2 upstream.
In Cilium some of the main programs we run today are hitting 9 passes
on x64's JIT compiler, and we've had cases already where we surpassed
the limit where the JIT then punts the program to the interpreter
instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON
or insertion failures due to the prog array owner being JITed but the
program to insert not (both must have the same JITed/non-JITed property).
One concrete case the program image shrunk from 12,767 bytes down to
10,288 bytes where the image converged after 16 steps. I've measured
that this took 340us in the JIT until it converges on my i7-6600U. Thus,
increase the original limit we had from day one where the JIT covered
cBPF only back then before we run into the case (as similar with the
complexity limit) where we trip over this and hit program rejections.
Also add a cond_resched() into the compilation loop, the JIT process
runs without any locks and may sleep anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fa4fe85f4 upstream.
The current check statement in BPF syscall will do a capability check
for CAP_SYS_ADMIN before checking sysctl_unprivileged_bpf_disabled. This
code path will trigger unnecessary security hooks on capability checking
and cause false alarms on unprivileged process trying to get CAP_SYS_ADMIN
access. This can be resolved by simply switch the order of the statement
and CAP_SYS_ADMIN is not required anyway if unprivileged bpf syscall is
allowed.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87e0d4f0f3 upstream.
Prasad reported that he has seen crashes in BPF subsystem with netd
on Android with arm64 in the form of (note, the taint is unrelated):
[ 4134.721483] Unable to handle kernel paging request at virtual address 800000001
[ 4134.820925] Mem abort info:
[ 4134.901283] Exception class = DABT (current EL), IL = 32 bits
[ 4135.016736] SET = 0, FnV = 0
[ 4135.119820] EA = 0, S1PTW = 0
[ 4135.201431] Data abort info:
[ 4135.301388] ISV = 0, ISS = 0x00000021
[ 4135.359599] CM = 0, WnR = 0
[ 4135.470873] user pgtable: 4k pages, 39-bit VAs, pgd = ffffffe39b946000
[ 4135.499757] [0000000800000001] *pgd=0000000000000000, *pud=0000000000000000
[ 4135.660725] Internal error: Oops: 96000021 [#1] PREEMPT SMP
[ 4135.674610] Modules linked in:
[ 4135.682883] CPU: 5 PID: 1260 Comm: netd Tainted: G S W 4.14.19+ #1
[ 4135.716188] task: ffffffe39f4aa380 task.stack: ffffff801d4e0000
[ 4135.731599] PC is at bpf_prog_add+0x20/0x68
[ 4135.741746] LR is at bpf_prog_inc+0x20/0x2c
[ 4135.751788] pc : [<ffffff94ab7ad584>] lr : [<ffffff94ab7ad638>] pstate: 60400145
[ 4135.769062] sp : ffffff801d4e3ce0
[...]
[ 4136.258315] Process netd (pid: 1260, stack limit = 0xffffff801d4e0000)
[ 4136.273746] Call trace:
[...]
[ 4136.442494] 3ca0: ffffff94ab7ad584 0000000060400145 ffffffe3a01bf8f8 0000000000000006
[ 4136.460936] 3cc0: 0000008000000000 ffffff94ab844204 ffffff801d4e3cf0 ffffff94ab7ad584
[ 4136.479241] [<ffffff94ab7ad584>] bpf_prog_add+0x20/0x68
[ 4136.491767] [<ffffff94ab7ad638>] bpf_prog_inc+0x20/0x2c
[ 4136.504536] [<ffffff94ab7b5d08>] bpf_obj_get_user+0x204/0x22c
[ 4136.518746] [<ffffff94ab7ade68>] SyS_bpf+0x5a8/0x1a88
Android's netd was basically pinning the uid cookie BPF map in BPF
fs (/sys/fs/bpf/traffic_cookie_uid_map) and later on retrieving it
again resulting in above panic. Issue is that the map was wrongly
identified as a prog! Above kernel was compiled with clang 4.0,
and it turns out that clang decided to merge the bpf_prog_iops and
bpf_map_iops into a single memory location, such that the two i_ops
could then not be distinguished anymore.
Reason for this miscompilation is that clang has the more aggressive
-fmerge-all-constants enabled by default. In fact, clang source code
has a comment about it in lib/AST/ExprConstant.cpp on why it is okay
to do so:
Pointers with different bases cannot represent the same object.
(Note that clang defaults to -fmerge-all-constants, which can
lead to inconsistent results for comparisons involving the address
of a constant; this generally doesn't matter in practice.)
The issue never appeared with gcc however, since gcc does not enable
-fmerge-all-constants by default and even *explicitly* states in
it's option description that using this flag results in non-conforming
behavior, quote from man gcc:
Languages like C or C++ require each variable, including multiple
instances of the same variable in recursive calls, to have distinct
locations, so using this option results in non-conforming behavior.
There are also various clang bug reports open on that matter [1],
where clang developers acknowledge the non-conforming behavior,
and refer to disabling it with -fno-merge-all-constants. But even
if this gets fixed in clang today, there are already users out there
that triggered this. Thus, fix this issue by explicitly adding
-fno-merge-all-constants to the kernel's Makefile to generically
disable this optimization, since potentially other places in the
kernel could subtly break as well.
Note, there is also a flag called -fmerge-constants (not supported
by clang), which is more conservative and only applies to strings
and it's enabled in gcc's -O/-O2/-O3/-Os optimization levels. In
gcc's code, the two flags -fmerge-{all-,}constants share the same
variable internally, so when disabling it via -fno-merge-all-constants,
then we really don't merge any const data (e.g. strings), and text
size increases with gcc (14,927,214 -> 14,942,646 for vmlinux.o).
$ gcc -fverbose-asm -O2 foo.c -S -o foo.S
-> foo.S lists -fmerge-constants under options enabled
$ gcc -fverbose-asm -O2 -fno-merge-all-constants foo.c -S -o foo.S
-> foo.S doesn't list -fmerge-constants under options enabled
$ gcc -fverbose-asm -O2 -fno-merge-all-constants -fmerge-constants foo.c -S -o foo.S
-> foo.S lists -fmerge-constants under options enabled
Thus, as a workaround we need to set both -fno-merge-all-constants
*and* -fmerge-constants in the Makefile in order for text size to
stay as is.
[1] https://bugs.llvm.org/show_bug.cgi?id=18538
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chenbo Feng <fengc@google.com>
Cc: Richard Smith <richard-llvm@metafoo.co.uk>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: linux-kernel@vger.kernel.org
Tested-by: Prasad Sodagudi <psodagud@codeaurora.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3346a6a4e5 upstream.
sysret_ss_attrs fails to compile leading x86 test run to fail on systems
configured to build using PIE by default. Add -no-pie fix it.
Relocation might still fail if relocated above 4G. For now this change
fixes the build and runs x86 tests.
tools/testing/selftests/x86$ make
gcc -m64 -o .../tools/testing/selftests/x86/single_step_syscall_64 -O2
-g -std=gnu99 -pthread -Wall single_step_syscall.c -lrt -ldl
gcc -m64 -o .../tools/testing/selftests/x86/sysret_ss_attrs_64 -O2 -g
-std=gnu99 -pthread -Wall sysret_ss_attrs.c thunks.S -lrt -ldl
/usr/bin/ld: /tmp/ccS6pvIh.o: relocation R_X86_64_32S against `.text'
can not be used when making a shared object; recompile with -fPIC
/usr/bin/ld: final link failed: Nonrepresentable section on output
collect2: error: ld returned 1 exit status
Makefile:49: recipe for target
'.../tools/testing/selftests/x86/sysret_ss_attrs_64' failed
make: *** [.../tools/testing/selftests/x86/sysret_ss_attrs_64] Error 1
Suggested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d12fe87e62 upstream.
Fix the debug print statements in these tests where they reference
si_codes and in particular __SI_FAULT. __SI_FAULT is a kernel
internal value and should never be seen by userspace.
While I am in there also fix si_code_str. si_codes are an enumeration
there are not a bitmap so == and not & is the apropriate operation to
test for an si_code.
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Fixes: 5f23f6d082 ("x86/pkeys: Add self-tests")
Fixes: e754aedc26 ("x86/mpx, selftests: Add MPX self test")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2195bff041 upstream.
The siginfo contains a bunch of information about the fault.
For protection keys, it tells us which protection key's
permissions were violated.
The wrong offset in here leads to reading garbage and thus
failures in the tests.
We should probably eventually move this over to using the
kernel's headers defining the siginfo instead of a hard-coded
offset. But, for now, just do the simplest fix.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8ba61ba58 upstream.
There's nothing IST-worthy about #BP/int3. We don't allow kprobes
in the small handful of places in the kernel that run at CPL0 with
an invalid stack, and 32-bit kernels have used normal interrupt
gates for #BP forever.
Furthermore, we don't allow kprobes in places that have usergs while
in kernel mode, so "paranoid" is also unnecessary.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32d43cd391 upstream.
The undocumented 'icebp' instruction (aka 'int1') works pretty much like
'int3' in the absense of in-circuit probing equipment (except,
obviously, that it raises #DB instead of raising #BP), and is used by
some validation test-suites as such.
But Andy Lutomirski noticed that his test suite acted differently in kvm
than on bare hardware.
The reason is that kvm used an inexact test for the icebp instruction:
it just assumed that an all-zero VM exit qualification value meant that
the VM exit was due to icebp.
That is not unlike the guess that do_debug() does for the actual
exception handling case, but it's purely a heuristic, not an absolute
rule. do_debug() does it because it wants to ascribe _some_ reasons to
the #DB that happened, and an empty %dr6 value means that 'icebp' is the
most likely casue and we have no better information.
But kvm can just do it right, because unlike the do_debug() case, kvm
actually sees the real reason for the #DB in the VM-exit interruption
information field.
So instead of relying on an inexact heuristic, just use the actual VM
exit information that says "it was 'icebp'".
Right now the 'icebp' instruction isn't technically documented by Intel,
but that will hopefully change. The special "privileged software
exception" information _is_ actually mentioned in the Intel SDM, even
though the cause of it isn't enumerated.
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 746201235b upstream.
While waiting for the TX object to send an RTR, an external message with a
matching id can overwrite the TX data. In this case we must call the rx
routine and then try transmitting the message that was overwritten again.
The queue was being stalled because the RX event did not generate an
interrupt to wake up the queue again and the TX event did not happen
because the TXRQST flag is reset by the chip when new data is received.
According to the CC770 datasheet the id of a message object should not be
changed while the MSGVAL bit is set. This has been fixed by resetting the
MSGVAL bit before modifying the object in the transmit function and setting
it after. It is not enough to set & reset CPUUPD.
It is important to keep the MSGVAL bit reset while the message object is
being modified. Otherwise, during RTR transmission, a frame with matching
id could trigger an rx-interrupt, which would cause a race condition
between the interrupt routine and the transmit function.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Tested-by: Richard Weinberger <richard@nod.at>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 591d65d5b1 upstream.
Older versions of the core are not compatible with the driver due
to various intrusive fixes of the core. Read out the VER register,
check the core revision bitfield and verify if the core in use is
new enough (rev 2.1 or newer) to work correctly with this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 880dd464b4 upstream.
The new version of the IFI CANFD core has significantly less complex
error state indication logic. In particular, the warning/error state
bits are no longer all over the place, but are all present in the
STATUS register. Moreover, there is a new IRQ register bit indicating
transition between error states (active/warning/passive/busoff).
This patch makes use of this bit to weed out the obscure selective
INTERRUPT register clearing, which was used to carry over the error
state indication into the poll function. While at it, this patch
fixes the handling of the ACTIVE state, since the hardware provides
indication of the core being in ACTIVE state and that in turn fixes
the state transition indication toward userspace. Finally, register
reads in the poll function are moved to the matching subfunctions
since those are also no longer needed in the poll function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c41aa24ba upstream.
If the server is malicious then *bytes_read could be larger than the
size of the "target" buffer. It would lead to memory corruption when we
do the memcpy().
Reported-by: Dr Silvio Cesare of InfoSect <Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b00c35138 upstream.
Due to missing information in Hardware manual, current
implementation doesn't read ECCSTAT0 and ECCSTAT1 registers
for IFC 2.0.
Add support to read ECCSTAT0 and ECCSTAT1 registers during
ecccheck for IFC 2.0.
Fixes: 656441478e ("mtd: nand: ifc: Fix location of eccstat registers for IFC V1.0")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 843c3a5999 upstream.
Number of ECC status registers i.e. (ECCSTATx) has been increased in IFC
version 2.0.0 due to increase in SRAM size. This is causing eccstat
array to over flow.
So, replace eccstat array with u32 variable to make it fail-safe and
independent of number of ECC status registers or SRAM size.
Fixes: bccb06c353 ("mtd: nand: ifc: update bufnum mask for ver >= 2.0.0")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa8e6d58c5 upstream.
As per the IFC hardware manual, Most significant 2 bytes in
nand_fsr register are the outcome of NAND READ STATUS command.
So status value need to be shifted and aligned as per the nand
framework requirement.
Fixes: 82771882d9 ("NAND Machine support for Integrated Flash Controller")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6de564939e upstream.
Section was not properly computed. The value of OOB region definition is
always ECC section 0 information in the OOB area, but we want to get all
the ECC bytes information, so we should call
mtd_ooblayout_ecc(mtd, section++, &oobregion) until it returns -ERANGE.
Fixes: c2b78452a9 ("mtd: use mtd_ooblayout_xxx() helpers where appropriate")
Cc: <stable@vger.kernel.org>
Signed-off-by: OuYang ZhiZhong <ouyzz@yealink.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78dc897b7e upstream.
In commit c713fb071e ("rtlwifi: rtl8821ae: Fix connection lost problem
correctly") a problem in rtl8821ae that caused loss of signal was fixed.
That same problem has now been reported for rtl8723be. Accordingly,
the ASPM L1 latency has been increased from 0 to 7 to fix the instability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 455f3e76cf upstream.
The firmware has a requirement that the P2P_DEVICE address should
be different from the address of the primary interface. When not
specified by user-space, the driver generates the MAC address for
the P2P_DEVICE interface using the MAC address of the primary
interface and setting the locally administered bit. However, the MAC
address of the primary interface may already have that bit set causing
the creation of the P2P_DEVICE interface to fail with -EBUSY. Fix this
by using a random address instead to determine the P2P_DEVICE address.
Cc: stable@vger.kernel.org # 3.10.y
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ffb0ba9b5 upstream.
Prior to 25520d55cd ("block: Inline blk_integrity in struct gendisk")
we needed to temporarily add a zero-capacity disk before registering for
blk-integrity. But adding a zero-capacity disk caused the partition
table scanning to bail early, and this resulted in partitions not coming
up after a probe of the BTT or blk namespaces.
We can now register for integrity before the disk has been added, and
this fixes the rescan problems.
Fixes: 25520d55cd ("block: Inline blk_integrity in struct gendisk")
Reported-by: Dariusz Dokupil <dariusz.dokupil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc9e0a9347 upstream.
Commit 99759869fa "acpi: Add acpi_map_pxm_to_online_node()" added
support for mapping a given proximity to its nearest, by SLIT distance,
online node. However, it sometimes returns unexpected results due to the
fact that it switches from comparing the PXM node to the last node that
was closer than the current max.
for_each_online_node(n) {
dist = node_distance(node, n);
if (dist < min_dist) {
min_dist = dist;
node = n; <---- from this point we're using the
wrong node for node_distance()
Fixes: 99759869fa ("acpi: Add acpi_map_pxm_to_online_node()")
Cc: <stable@vger.kernel.org>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73a88250b7 upstream.
When validating legacy surfaces, the backup bo might be destroyed at
surface validate time. However, the kms resource validation code may have
the bo reserved, so we will destroy a locked mutex. While there shouldn't
be any other users of that mutex when it is destroyed, it causes a lock
leak and thus throws a lockdep error.
Fix this by having the kms resource validation code hold a reference to
the bo while we have it reserved. We do this by introducing a validation
context which might come in handy when the kms code is extended to validate
multiple resources or buffers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6bdb7517c upstream.
On architectures with CONFIG_HAVE_ARCH_HUGE_VMAP set, ioremap() may
create pud/pmd mappings. A kernel panic was observed on arm64 systems
with Cortex-A75 in the following steps as described by Hanjun Guo.
1. ioremap a 4K size, valid page table will build,
2. iounmap it, pte0 will set to 0;
3. ioremap the same address with 2M size, pgd/pmd is unchanged,
then set the a new value for pmd;
4. pte0 is leaked;
5. CPU may meet exception because the old pmd is still in TLB,
which will lead to kernel panic.
This panic is not reproducible on x86. INVLPG, called from iounmap,
purges all levels of entries associated with purged address on x86. x86
still has memory leak.
The patch changes the ioremap path to free unmapped page table(s) since
doing so in the unmap path has the following issues:
- The iounmap() path is shared with vunmap(). Since vmap() only
supports pte mappings, making vunmap() to free a pte page is an
overhead for regular vmap users as they do not need a pte page freed
up.
- Checking if all entries in a pte page are cleared in the unmap path
is racy, and serializing this check is expensive.
- The unmap path calls free_vmap_area_noflush() to do lazy TLB purges.
Clearing a pud/pmd entry before the lazy TLB purges needs extra TLB
purge.
Add two interfaces, pud_free_pmd_page() and pmd_free_pte_page(), which
clear a given pud/pmd entry and free up a page for the lower level
entries.
This patch implements their stub functions on x86 and arm64, which work
as workaround.
[akpm@linux-foundation.org: fix typo in pmd_free_pte_page() stub]
Link: http://lkml.kernel.org/r/20180314180155.19492-2-toshi.kani@hpe.com
Fixes: e61ce6ade4 ("mm: change ioremap to set up huge I/O mappings")
Reported-by: Lei Li <lious.lilei@hisilicon.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Wang Xuefeng <wxf.wang@hisilicon.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Chintan Pandya <cpandya@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68ef3bc316 upstream.
We had some reports of panics in nfsd4_lm_notify, and that showed a
nfs4_lockowner that had outlived its so_client.
Ensure that we walk any leftover lockowners after tearing down all of
the stateids, and remove any blocked locks that they hold.
With this change, we also don't need to walk the nbl_lru on nfsd_net
shutdown, as that will happen naturally when we tear down the clients.
Fixes: 76d348fadf (nfsd: have nfsd4_lock use blocking locks for v4.1+ locks)
Reported-by: Frank Sorenson <fsorenso@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@vger.kernel.org # 4.9
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d418ff56b8 upstream.
When commit 9c7be59fc5 ("libata: Apply NOLPM quirk to Crucial MX100
512GB SSDs") was added it inherited the ATA_HORKAGE_NO_NCQ_TRIM quirk
from the existing "Crucial_CT*MX100*" entry, but that entry sets model_rev
to "MU01", where as the entry adding the NOLPM quirk sets it to NULL.
This means that after this commit we no apply the NO_NCQ_TRIM quirk to
all "Crucial_CT512MX100*" SSDs even if they have the fixed "MU02"
firmware. This commit splits the "Crucial_CT512MX100*" quirk into 2
quirks, one for the "MU01" firmware and one for all other firmware
versions, so that we once again only apply the NO_NCQ_TRIM quirk to the
"MU01" firmware version.
Fixes: 9c7be59fc5 ("libata: Apply NOLPM quirk to ... MX100 512GB SSDs")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bf7b5d6d0 upstream.
Commit b17e5729a6 ("libata: disable LPM for Crucial BX100 SSD 500GB
drive"), introduced a ATA_HORKAGE_NOLPM quirk for Crucial BX100 500GB SSDs
but limited this to the MU02 firmware version, according to:
http://www.crucial.com/usa/en/support-ssd-firmware
MU02 is the last version, so there are no newer possibly fixed versions
and if the MU02 version has broken LPM then the MU01 almost certainly
also has broken LPM, so this commit changes the quirk to apply to all
firmware versions.
Fixes: b17e5729a6 ("libata: disable LPM for Crucial BX100 SSD 500GB...")
Cc: stable@vger.kernel.org
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
